Osteoblast response to titanium surfaces functionalized with extracellular matrix peptide biomimetics.

OBJECTIVE: Functionalizing surfaces with specific peptides may aid osteointegration of orthopedic implants by favoring attachment of osteoprogenitor cells and promoting osteoblastic differentiation. This study addressed the hypothesis that implant surfaces functionalized with peptides targeting multiple ligands will enhance osteoblast attachment and/or differentiation. To test this hypothesis, we used titanium (Ti) surfaces coated with poly-l-lysine-grafted polyethylene glycol (PLL-g-PEG) and functionalized with two peptides found in extracellular matrix proteins, arginine-glycine-aspartic acid (RGD) and lysine-arginine-serine-arginine (KRSR), which have been shown to increase osteoblast attachment. KSSR, which does not promote osteoblast attachment, was used as a control. MATERIALS AND METHODS: Sandblasted acid-etched titanium surfaces were coated with PLL-g-PEG functionalized with varying combinations of RGD and KRSR, as well as KSSR. Effects of these surfaces on osteoblasts were assessed by measuring cell number, alkaline phosphatase-specific activity, and levels of osteocalcin, transforming growth factor beta-1 (TGF-ß1), and PGE(2). RESULTS: RGD increased cell number, but decreased markers for osteoblast differentiation. KRSR alone had no effect on cell number, but decreased levels of TGF-ß1 and PGE(2). KRSR and RGD/KRSR coatings inhibited osteoblast differentiation vs. PLL-g-PEG. KSSR decreased cell number and increased osteoblast differentiation, indicated by increased levels of osteocalcin and PGE(2). CONCLUSIONS: The RGD and KRSR functionalized surfaces supported attachment but did not enhance osteoblast differentiation, whereas KSSR increased differentiation. RGD decreased this effect, suggesting that multifunctional peptide surfaces can be designed that improve peri-implant healing by optimizing attachment and proliferation as well as differentiation of osteoblasts, but peptide combination, dose and presentation are critical variables.

Bacterial biofilm formation versus mammalian cell growth on titanium-based mono- and bi-functional coating.

Biomaterials-associated-infections (BAI) are serious complications in modern medicine. Although non-adhesive coatings, like polymer-brush coatings, have been shown to prevent bacterial adhesion, they do not support cell growth. Bi-functional coatings are supposed to prevent biofilm formation while supporting tissue integration. Here, bacterial and cellular responses to poly(ethylene glycol) (PEG) brush-coatings on titanium oxide presenting the integrin-active peptide RGD (arginine-glycine-aspartic acid) (bioactive "PEG-RGD") were compared to mono-functional PEG brush-coatings (biopassive "PEG") and bare titanium oxide (TiO2) surfaces under flow. Staphylococcus epidermidis ATCC 35983 was deposited on the surfaces under a shear rate of 11 s-1 for 2 h followed by seeding of U2OS osteoblasts. Subsequently, both S. epidermidis and U2OS cells were grown simultaneously on the surfaces for 48 h under low shear (0.14 s-1). After 2 h, staphylococcal adhesion was reduced to 3.6-/+1.8 x 103 and 6.0-/+3.9 x 103 cm-2 on PEG and PEG-RGD coatings respectively, compared to 1.3-/+0.4 x 105 cm-2 for the TiO2 surface. When allowed to grow for 48 h, biofilms formed on all surfaces. However, biofilms detached from the PEG and PEG-RGD coatings when exposed to an elevated shear (5.6 s-1) U2OS cells neither adhered nor spread on PEG brush-coatings, regardless of the presence of biofilm. In contrast, in the presence of biofilm, U2OS cells adhered and spread on PEG-RGD coatings with a significantly higher surface coverage than on bare TiO2. The detachment of biofilm and the high cell surface coverage revealed the potential significance of PEG-RGD coatings in the context of the "race for the surface" between bacteria and mammalian cells.

Reduced medical infection related bacterial strains adhesion on bioactive RGD modified titanium surfaces: a first step toward cell selective surfaces.

Ideally, implants should inhibit nonspecific protein adsorption, bacterial adhesion, and at the same time, depending on the final application be selective toward cellular adhesion and spreading for all or only selected cell types. Poly(L-lysine)-grafted-poly(ethylene glycol) (PLL-g-PEG) polymers have been shown to adsorb from aqueous solution onto negatively charged metal oxide surfaces, reducing protein adsorption as well as fibroblast, osteoblast and epithelial cell adhesion significantly. PLL-g-PEG can be functionalized with bioligands such as RGD (Arg-Gly-Asp), which then restores host cell adhesion, but the surface remains resistant to nonspecific protein adsorption. Previously, it was also shown that both nonfunctionalized PLL-g-PEG and RGD-peptide functionalized PLL-g-PEG reduced the adhesion of Staphylococcus aureus to titanium (Ti) surfaces. The present study looked at the effect of other implant associated infection relevant bacteria, Staphylococcus epidermidis, Streptococcus mutans and Pseudomonas aeruginosa towards the same surface chemistries. The different surfaces were exposed to the bacteria for 1-24 h, and bacteria surface density was evaluated using scanning electron microscopy (SEM) and fluorescence light microscopy (FM). The adhesion of all bacteria strains tested was reduced on Ti surfaces coated with PLL-g-PEG compared to uncoated Ti surfaces even in the presence of RGD. The percentage reduction in bacterial adhesion over the 24-h culture time investigated was 88%-98%, depending on the bacteria type. Therefore, coating surfaces with PLL-g-PEG/PEG-RGD allows cells such as fibroblasts and osteoblasts to attach but not bacteria, resulting in a selective biointeractive pattern that may be useful on medical implants.

MICROPATTERNING OF GOLD SUBSTRATES BASED ON POLY(PROPYLENE SULFIDE-BL-ETHYLENE GLYCOL), (PPS-PEG) BACKGROUND PASSIVATION AND THE MOLECULAR-ASSEMBLY PATTERNING BY LIFT-OFF (MAPL) TECHNIQUE.

Poly(propylene sulfide-bl-ethylene glycol (PPS-PEG) is an amphiphilic block copolymer that spontaneously adsorbs onto gold from solution. This results in the formation of a stable polymeric layer that renders the surface protein resistant when an appropriate architecture is chosen. The established molecular assembly patterning by lift-off (MAPL) technique can convert a prestructured resist film into a pattern of biointeractive chemistry and a noninteractive background. Employing the MAPL technique, we produced a micron-scale PPS-PEG pattern on a gold substrate, and then characterized the patterned structure with Time-of-Flight Secondary Ion Mass Spectrometry (TOF-SIMS) and Atomic Force Microscopy (AFM). Subsequent exposure of the PPS-PEG/gold pattern to protein adsorption (full human serum) was monitored in situ; SPR-imaging (i-SPR) shows a selective adsorption of proteins on gold, but not on PPS-PEG areas. Analysis shows a reduction of serum adsorption up to 93% on the PPS-PEG areas as compared to gold, in good agreement with previous analysis of homogenously adsorbed PPS-PEG on gold. MAPL patterning of PPS-PEG block copolymers is straightforward, versatile and reproducible, and may be incorporated into biosensor-based surface analysis methods.

Patterned cell adhesion by self-assembled structures for use with a CMOS cell-based biosensor.

A strategy for patterned cell adhesion based on chemical surface modification is presented. To confine cell adhesion to specific locations, an engineered surface for high-contrast protein adsorption and, hence, cell attachment has been developed. Surface functionalization is based on selective molecular-assembly patterning (SMAP). An amine-terminated self-assembled monolayer is used to define areas of cell adhesion. A protein-repellent grafted copolymer, poly(L-lysine)-graft-poly(ethylene glycol) (PLL-g-PEG), is used to render the surrounding silicon dioxide resistant to protein adsorption. X-ray photoelectron spectroscopy, scanning ellipsometry and fluorescence microscopy techniques were used to monitor the individual steps of the patterning process. Successful guided growth using these layers is demonstrated with primary neonatal rat cardiomyocytes, up to 4 days in vitro, and with the HL-1 cardiomyocyte cell line, up to 7 days in vitro. The advantage of the presented method is that high-resolution engineered surfaces can be realized using a simple, cost-effective, dip-and-rinse process. The technique has been developed for application on a CMOS cell-based biosensor, which comprises an array of microelectrodes to extracellularly record electrical activity from cardiomyocytes.

Electrophoretic deposition of zirconia-Bioglass composite coatings for biomedical implants.

Composite bilayer coatings on Ti6Al4V substrates were prepared by electrophoretic deposition, a simple and fast low temperature coating technique. Biocompatible yttrium-stabilized zirconia (YSZ) in the form of nanoparticles and bioactive Bioglass (45S5) in the form of microparticles were chosen as coating materials. The first layer consisted of 5 microm of YSZ, deposited with the intention to avoid any metal tissue contact. The second layer consisted of 15-microm thick 45S5-YSZ composite, supposed to react with the surrounding bone tissue and to enhance implant fixation. The adsorption of YSZ nanoparticles on 45S5 microparticles in organic suspension was found to invert the surface charge of the 45S5 particles from negative to positive. This enabled cathodic electrophoretic deposition of 45S5, avoiding uncontrolled anodization (oxidation) of the substrate. The coatings were sintered at 900 degrees C for 2 h under argon flow. The characterization was performed using SEM, EDX, and nanoindentation (cross section). Potential applications in the orthopedics field are discussed.

Waveguide excitation fluorescence microscopy: a new tool for sensing and imaging the biointerface.

A novel biosensing and imaging technique, the waveguide excitation fluorescence microscope, has been developed for the dynamic and quantitative investigation of bio-interfacial events in situ, ranging from ligand-receptor binding to focal adhesion formation in cell-surface interactions. The technique makes use of the evanescent field created when light travels in a mono-mode, planar optical waveguide to excite fluorescence in the near interface region. Advantages of the technique include high target sensitivity for fluorescence detection (femtomolar range), high surface specificity (ca. 100 nm perpendicular to the waveguide), large area analysis with submicron resolution, 'built-in' calibration of fluorescent light gain, and the capability to perform multi-colour imaging in situ and in real time. In this work, the sensitivity of the system has already been demonstrated through dynamic measurements of the streptavidin-biotin binding event to below 20 pM concentrations, signal to noise comparisons with conventional fluorescence microscopy have shown more than a 10-fold improvement, and surface specificity of the technique has also been illustrated in a comparison of fibroblast focal adhesion images. Thus, this new tool can be used to illuminate processes occurring at the interface between biology and synthetic surfaces in a unique manner.

Functionalization of titanium oxide surfaces by means of poly(alkyl-phosphonates).

The use of a multiple attachment sites strategy is considered in order to improve the stability of monomolecular adlayers. The hypothesis was tested in the case of PEG-ylated compounds carrying phosphonate groups, known for their affinity toward titanium oxide surfaces. As a result, a new class of co- and terpolymers were synthesized by free-radical polymerization of three different monomers: dialkyl(methacryloyloxyalkyl)phosphonates, PEG methyl ether methacrylate, and/or butyl methacrylate monomers. Adlayers were formed following a simple dip-and-rinse protocol using diluted aqueous polymer solutions and were characterized by evaluating their thicknesses with variable angle spectroscopic ellipsometry (VASE) and their elemental compositions with X-ray photoelectron spectroscopy (XPS). The same techniques were used to determine changes of the adlayer as a function of exposure to electrolytes at different pH values and to monitor nonspecific protein adsorption upon serum exposures. The results indicated that the poly(alkyl-phosphonate)-based adlayers combine multiple site attachment of phosphonic groups and presentation of PEG side chains to the aqueous environment, resulting in both improved stability over a wide pH range in comparison to the tested reference surfaces and excellent resistance to protein adsorption when exposed to full human serum.

Silk fibroin as an organic polymer for controlled drug delivery.

The pharmaceutical utility of silk fibroin (SF) materials for drug delivery was investigated. SF films were prepared from aqueous solutions of the fibroin protein polymer and crystallinity was induced and controlled by methanol treatment. Dextrans of different molecular weights, as well as proteins, were physically entrapped into the drug delivery device during processing into films. Drug release kinetics were evaluated as a function of dextran molecular weight, and film crystallinity. Treatment with methanol resulted in an increase in beta-sheet structure, an increase in crystallinity and an increase in film surface hydrophobicity determined by FTIR, X-ray and contact angle techniques, respectively. The increase in crystallinity resulted in the sustained release of dextrans of molecular weights ranging from 4 to 40 kDa, whereas for less crystalline films sustained release was confined to the 40 kDa dextran. Protein release from the films was studied with horseradish peroxidase (HRP) and lysozyme (Lys) as model compounds. Enzyme release from the less crystalline films resulted in a biphasic release pattern, characterized by an initial release within the first 36 h, followed by a lag phase and continuous release between days 3 and 11. No initial burst was observed for films with higher crystallinity and subsequent release patterns followed linear kinetics for HRP, or no substantial release for Lys. In conclusion, SF is an interesting polymer for drug delivery of polysaccharides and bioactive proteins due to the controllable level of crystallinity and the ability to process the biomaterial in biocompatible fashion under ambient conditions to avoid damage to labile compounds to be delivered.

Substratum roughness alters the growth, area, and focal adhesions of epithelial cells, and their proximity to titanium surfaces.

Epithelial (E) cells were cultured on smooth tissue culture plastic (TCP), TCP-Ti, polished Ti (P), and rough grit-blasted Ti (B), acid-etched Ti (AE), and grit-blasted and acid-etchedTi (SLA) surfaces and their growth, area, adhesion, and membrane-Ti proximity assessed. Rough surfaces decreased the growth of E cells compared to smooth surfaces in cultures up to 28 days. In general rough surfaces decreased the spreading of E cells as assessed by their area with the most pronounced affect for the SLA surface. On the other hand, the strength of E cells adhesion as inferred by immunofluorescence staining of vinculin in focal adhesions indicated that E cells formed more and larger focal adhesions on the smooth P surface compared to the rougher AE surface. As this finding indicates a stronger adhesion to smooth surfaces, it is likely that E cells on rough surfaces are more susceptible to mechanical removal. An immunogold labeling method was developed to visualize focal adhesions using back-scattered electron imaging with a scanning electron microscope (SEM). On rough surfaces focal adhesions were primarily localized on to the ridges rather than the valleys and the cells tended to bridge over the valleys. Transmission electron microscopy (TEM) measurements of membrane proximity to the Ti surface indicated that average distance of cell to the Ti increased as the Ti surface roughness increased. Therefore, the size and shape of surface features are important determinants of epithelial adhesive behavior and epithelial coverage of rough surfaces would be difficult to attain if such surfaces become exposed.

Anodic plasma-chemical treatment of CP titanium surfaces for biomedical applications.

The anodic plasma-chemical (APC) process was used to modify CP titanium surfaces for biomedical applications. This technique allows for the combined chemical and morphological modification of titanium surfaces in a single process step. The resulting conversion coatings, typically several micrometer thick, consist mainly of titanium oxide and significant amounts of electrolyte constituents. In this study, a new electrolyte was developed containing both calcium-stabilized by complexation with EDTA-and phosphate ions at pH 14. The presence of the Ca-EDTA complex, negatively charged at high pH, favors incorporation of high amounts of calcium into the APC coatings during the anodic (positive) polarization. The coating properties were evaluated as a function of the process variables by XPS, GD-OES, Raman spectroscopy, SEM and tensile testing, and compared to those of calcium-free APC coatings and uncoated CP titanium surfaces. The maximal Ca/P atomic ratio in the coating produced with the new APC electrolyte was approximately 1.3, with higher Ca concentrations than reported in conventional APC coatings. The dissolution behavior of the incorporated, amorphous CaP phases was investigated by exposure to a diluted EDTA solution. The coatings produced in the new electrolyte system exhibit favorable mechanical stability. The new APC technology is believed to be a versatile and cost-effective coating technique to render titanium implant surfaces bioactive.

Staphylococcus aureus adhesion to titanium oxide surfaces coated with non-functionalized and peptide-functionalized poly(L-lysine)-grafted-poly(ethylene glycol) copolymers.

Implanted biomaterials are coated immediately with host plasma constituents, including extracellular matrix (ECM); this reaction may be undesirable in some cases. Poly(L-lysine)-grafted-poly(ethylene glycol) (PLL-g-PEG) has been shown to spontaneously adsorb from aqueous solution onto metal oxide surfaces, effectively reducing the degree of non-specific adsorption of blood and ECM proteins, and decreasing the adhesion of fibroblastic and osteoblastic cells to the coated surfaces. Cell adhesion through specific peptide-integrin receptors could be restored on surfaces coated with PLL-g-PEG functionalized with peptides of the RGD (Arg-Asp-Gly) type. To date, no study has examined the effect of surface modifications by PLL-g-PEG-based polymers on bacterial adhesion. The ability of Staphylococcus aureus to adhere to the ECM and plasma proteins deposited on biomaterials is a significant factor in the pathogenesis of medical-device-related infections. This study describes methods for visualizing and quantifying the adhesion of S. aureus to smooth and rough (chemically etched) titanium surfaces without and with monomolecular coatings of PLL-g-PEG, PLL-g-PEG/PEG-RGD and PLL-g-PEG/PEG-RDG. The different surfaces were exposed to S. aureus cultures for 1-24h and bacteria surface density was evaluated using scanning electron microscopy and fluorescence microscopy. Coating titanium surfaces with any of the three types of copolymers significantly decreased the adhesion of S. aureus to the surfaces by 89-93% for PLL-g-PEG, and 69% for PLL-g-PEG/PEG-RGD. Therefore, surfaces coated with PLL-g-PEG/PEG-RGD have the ability to attach cells such as fibroblasts and osteoblasts while showing reduced S. aureus adhesion, resulting in a selective biointeraction pattern that may be useful for applications in the area of osteosynthesis, orthopaedic and dental implantology.

Chemically patterned, metal oxide based surfaces produced by photolithographic techniques for studying protein- and cell-surface interactions I: Microfabrication and surface characterization.

Chemical patterns on smooth wafer substrates comprising areas with two different metals have been produced by vacuum metal deposition and photolithographic techniques. The combination of metals has been chosen from the series titanium (Ti), aluminium (Al), vanadium (V) and niobium (Nb), producing patterns (dots and stripes with dimensions of 50, 100 and 150 micrometer) with one of the metals as the background and with the second metal (foreground pattern) deposited on the background metal. The structure and chemical composition of the patterned surfaces were evaluated by scanning electron microscopy, X-ray photoelectron spectroscopy and imaging time-of-flight secondary-ion mass spectrometry. The surfaces proved to be geometrically well defined with the expected surface-chemical composition, i.e. a surface oxide (passive) film essentially composed of TiO(2),Al(2)O(3),V(2)O(5), or Nb(2)O(5). Ti/Ti patterned surfaces were produced as controls and found to show no chemical composition contrast. The surface roughness of the pattern was greater than that of the background by a factor of 2-3, but was still extremely smooth with Ra<2nm. The patterns serve as model surfaces for studying in vitro the behaviour of cells as well as the adsorption of serum proteins on different metal oxides, which will be reported in a companion paper. These surfaces can be used to compare and contrast the response of osteoblasts to Ti and other alloy components, such as Al, V, or Nb, which are used in load-bearing medical implants.

Peptide functionalized poly(L-lysine)-g-poly(ethylene glycol) on titanium: resistance to protein adsorption in full heparinized human blood plasma.

The graft copolymer poly(L-lysine)-graft-poly(ethylene glycol) (PLL-g-PEG) and its RGD- and RDG-functionalized derivatives (PLL-g-PEG/PEG-peptide) were assembled from aqueous solutions on titanium (oxide) surfaces. The polymers were characterized by NMR in order to determine quantitatively the grafting ratio, g (Lys monomer units/PEG side chains), and the fraction of the PEG side chains carrying the terminal peptide group. The titanium surfaces modified with the polymeric monomolecular adlayers were exposed to full heparinized blood plasma. The adsorbed masses were measured by in situ ellipsometry. The different PLL-g-PEG-coated surfaces showed, within the detection limit of the ellipsometric technique, no statistically significant protein adsorption during exposure to plasma for 30 min at 22 degrees C or 37 degrees C, whereas clean, uncoated titanium surfaces adsorbed approximately 350 ng/cm2 of plasma proteins. The high degree of resistance of the PEGylated surface to non-specific adsorption makes peptide-modified PLL-g-PEG a useful candidate for the surface modification of biomedical devices such as implants that are capable of eliciting specific interactions with integrin-type cell receptors even in the presence of full blood plasma. The results refer to short-term blood plasma exposure that cannot be extrapolated a priori to long-term clinical performance.

Optical grating coupler biosensors.

By incorporating a grating in a planar optical waveguide one creates a device with which the spectrum of guided lightmodes can he measured. When the surface of the waveguide is exposed to different solutions, the peaks in the spectrum shift due to molecular interactions with the surface. Optical waveguide lightmode spectroscopy (OWLS) is a highly sensitive technique that is capable of real-time monitoring of these interactions. Since this integrated optical method is based on the measurement of the polarizability density (i.e., refractive index) in the vicinity of the waveguide surface, radioactive, fluorescent or other kinds of labeling are not required. In addition, measurement of at least two guided modes enables the absolute mass of adsorbed molecules to be determined. In this article, the technique will be described in some detail, and applications from different areas will be discussed. Selected examples will be presented to demonstrate how monitoring the modification of different metal oxides with polymers and the response of the coated oxides to biofluids help in the design of novel biomaterials; how OWLS is useful for accurate bioaffinity sensing, which is a key issue in the development of new drugs; and how the quantitative study of protein-DNA/RNA and cell surface interactions can enhance the understanding of processes in molecular and cellular biology.

Chemically patterned, metal-oxide-based surfaces produced by photolithographic techniques for studying protein- and cell-interactions. II: Protein adsorption and early cell interactions.

Protein adsorption and adhesion of primary human osteoblasts on chemically patterned, metal-oxide-based surfaces comprising combinations of titanium, aluminium, vanadium and niobium were investigated. Single metal samples with a homogeneous surface and bimetal samples with a surface pattern produced by photolithographic techniques were used. The physical and chemical properties of the samples have been extensively characterised and are presented in a companion paper. Here, we describe their properties in terms of cell responses during the initial 24h of cell culture. Regarding the cell number and activity there was no significant difference between any of the single metal surfaces. However the morphology of cells on vanadium surfaces became spindle-like. In contrast to the behaviour on single metal samples, cells exhibited a pronounced reaction on bimetallic surfaces that contained aluminium. Cells tended to stay away from aluminium, which was the least favoured metal in all two-metal combinations. An initial cell alignment relative to the pattern geometry was detectable after 2h and was fully developed after 18h of incubation. The organisation of f-actin and microtubules as well as the localisation of vinculin were all more pronounced on non-aluminium regions. We hypothesised that the differences in cell response could be associated with differences in the adsorption of serum proteins onto the various metal oxides. Protein adsorption experiments were performed using microscopy in conjunction with immunofluorescent stains. They indicated that both fibronectin and albumin adsorption were significantly greater on the non-aluminium regions, suggesting that differences in cellular response correlate with a modulation of the concentration of serum proteins on the surface.

Fibroblast and osteoblast adhesion and morphology on calcium phosphate surfaces.

Implant loosening in bone fixation is an unresolved complication associated with internal fixation. It is generally accepted that this problem can be overcome by modifying the implant/bone interface for improved osseointegration. This is achieved, in part, by hydroxyapatite (HA) or tricalcium phosphate coatings. Unfortunately, the benefits of these coatings are constrained by not only the generally low strength of their adhesion to the implant surface but also the limited cohesion within their layers. Anodic Plasma-chemical treatment (APC) has been developed to incorporate electrolytes and produce coatings with various microtopographies and strong adhesion to implants. In this in vitro study fibroblast and osteoblast morphologies and adhesion to various substrates were evaluated using qualitative and quantitative methods. The substrates were Thermanox plastic and commercially pure titanium. The latter were surface-treated using several different methods: conventional anodisation, plasma spraying of HA and anodic plasma-chemical (APC) treatment in an electrolyte solution containing either calcium and phosphate (APC-CaP) or phosphoric acid (APC-P). Both osteoblasts and fibroblasts showed extensive cell spreading, total cell area and greatest amount of adhesion, with defined adhesion patterns on the Thermanox plastic, anodised titanium, and the two APC-CaP substrates. With fibroblasts, almost no cell spreading and very low adhesion, was observed in cells cultured on the APC-P and HA surfaces. The extent of cell spreading correlated with the area of focal adhesions as assessed by the amount of vinculin labelling. The Thermanox plastic, anodised titanium, and the two APC-CaP substrates were the most cytocompatible substrates with regard to this in vitro evaluation.

Feasibility study of an online toxicological sensor based on the optical waveguide technique.

Morphological properties of the cells often change as an early response to the presence of a pharmacologically acting toxic substance [Etcheverry, S.B., Crans, D.C., Keramidas, A.D., Cortizo, A.M., Arch. Biochem. Biophys. 338 (1997) 7-14]. Recently it has been shown that living animal cell adhesion and spreading can be monitored online and quantitatively via the interaction of the cells with the evanescent electromagnetic field present at the surface of an optical waveguide [Ramsden, J.J., Li, S.Y., Heinzle, E., Prinosil, J.E. Cytometry 19 (1995) 97-102]. In the present study, optical waveguide lightmode spectroscopy (OWLS) and confocal laser scanning microscopy (CLSM), which provides information about the shape of the cells at the surface, were compared under identical experimental conditions. This allowed for the correlation between the cell-shape information from CLSM and the cell-surface interaction measurements from OWLS. The proposed design of the microsystem sensor involves the establishment of a cell layer on the surface of the waveguide and the subsequent online measurement of the morphological response of the cells to various toxic substances. In the present study, the setup was evaluated using cells from an osteoblastic MC 3T3-E1 cell line, and sodium hypochlorite was used as model toxic substance. Comparing the OWLS signal to the morphological response measured by CLSM reveals that OWLS is effective in monitoring not only cell attachment and spreading but also the cellular response to toxic compounds (i.e. by means of change in cell morphology). For the model toxin, the OWLS measurements indicate that, at concentrations above 0.01%, the cells exhibit a clearly discernable morphological effect (i.e. a decrease in average cell contact area). Thus, the potential of an on-line sensor based on OWLS to applications in toxicology, pharmacy and biocompatibility was demonstrated.

Advantages of stereo imaging of metallic surfaces with low voltage backscattered electrons in a field emission scanning electron microscope

High emission current backscattered electron (HC-BSE) stereo imaging at low accelerating voltages ( 10 keV) BSE or SE stereo images. The low voltage HC-BSE stereo images displayed similar surface detail to the low voltage SE images, although they showed more contrast and directional sensitivity on surface structures. At or below 5 keV, only structures a very short distance into the metallic surface were observed. At higher accelerating voltages a greater appearance of depth could be seen but there was less information on the fine surface detail and its angular orientation. The combined technique of HC-BSE imaging and stereo imaging should be useful for detailed studies on material surfaces and for biological samples with greater contrast and directional sensitivity than can be obtained with current SE or BSE detection modes.

Surface modification of PLGA microspheres.

Microspheres made of poly(lactic-co-glycolic acid) (PLGA) are biocompatible and biodegradable, rendering them a promising tool in the context of drug delivery. However, nonspecific adsorption of plasma proteins on PLGA micro- and nanospheres is a main limitation of drug targeting. Poly(L-lysine)-g-poly(ethylene glycol) (PLL-g-PEG), physisorbed on flat metal oxide surfaces, has previously been shown to suppress protein adsorption drastically. The goal of our work was to characterize the efficiency of the protein repellent character of PLL-g-PEG on PLGA microspheres and to show the feasibility of introducing functional groups on the PLGA microspheres via functionalized PLL-g-PEG. To quantify the adsorbed amount of protein, a semiquantitative method that uses confocal laser scanning microscopy (CLSM) was applied. The first part of the experiment confirms the feasibility of introducing specific functional groups on PLL-g-PEG-coated PLGA microspheres. In the second part of the experiment, PLL-g-PEG-coated PLGA microspheres show a drastic decrease of adsorbed proteins by two orders of magnitude in comparison to uncoated PLGA microspheres. Low protein-binding, functionalizable microspheres provide a fundamental basis for the design of drug delivery and biosensor systems.