Rotational scanning atomic force microscopy.

A non-raster scanning technique for atomic force microscopy (AFM) imaging which combines rotational and translational motion is presented. The use of rotational motion for the fast scan axis allows us to significantly increase the scanning speed while imaging a large area (diameter > 30 µm). An image reconstruction algorithm and the factors influencing the resolution of the technique are discussed. The experimental results show the potential of the rotational scanning technique for high-throughput large area AFM investigation.

Processive behaviour of kinesin observed using micro-fabricated cantilevers.

The mechanical characterization of biomolecular motors requires force sensors with sub-piconewton resolution. The coupling of a nanoscale motor to this type of microscale sensors introduces structural deformations in the motor according to the thermally activated degrees of freedom of the sensor. At present, no simple solution is available to reduce these effects. Here, we exploit the advantages of micro-fabricated cantilevers to produce a force sensor with essentially one degree of freedom and a spring constant of 0.03 pN nm(-1) for the study of the molecular motor protein kinesin-1. During processive runs, the cantilever constrains the movement of the cargo binding domain of kinesin in a straight line, parallel to the microtubule track, and excludes specific reaction coordinates such as cargo rotation. In these conditions, we measured a step size of 8.0 ± 0.4 nm and a maximal unloaded velocity of 820 ± 80 nm s(-1) at saturated adenosine triphosphate (ATP) concentration. We concluded that the motor does not need to rotate its tail as it moves through consecutive stepping cycles.

Hands-on with optical tweezers: a multitouch interface for holographic optical trapping.

We report the implementation of a multitouch console for control of a holographic optical tweezers system. This innovative interface enables the independent but simultaneous interactive control of numerous optical traps by multiple users, overcoming the limitations of traditional interfaces and placing the full power of holographic optical tweezing into the operators' hands.

Intermittent contact AFM using the higher modes of weak cantilever.

Employing the higher vibration modes of weak cantilevers enables operating frequencies up to megahertz to be reached, at the same time keeping the force on the sample reasonably low. This allows the interaction time between the tip and the surface to be reduced and should cause the response of surface to be dominated by surface stiffness. The simple distributed mass cantilever model is presented which shows that higher eigenmodes exhibit better sensitivity to surface properties. The images of laser-treated polymer on glass show the ability of the method to distinguish between the material phases with different properties.

Micro-fabricated mechanical sensors for lateral molecular-force microscopy.

Atomic force microscopy (AFM) has been very successful in measuring forces perpendicular to the sample plane. Here, we present the advantages of turning the AFM cantilever 90° in order for it to be perpendicular to the sample. This rotation leads naturally to the detection of in-plane forces with some extra advantages with respect to the AFM orientation. In particular, the use of extremely small (1µm wide) and soft (k≅10(-5)N/m) micro-fabricated cantilevers is demonstrated by recording their thermal power spectral density in ambient conditions and in liquid. These measurements lead to the complete characterisation of the sensors in terms of their stiffness and resonant frequency. Future applications, which will benefit from the use of this force microscopy technique, are also described.

High-speed AFM of human chromosomes in liquid.

Further developments of the previously reported high-speed contact-mode AFM are described. The technique is applied to the imaging of human chromosomes at video rate both in air and in water. These are the largest structures to have been imaged with high-speed AFM and the first imaging in liquid to be reported. A possible mechanism that allows such high-speed contact-mode imaging without significant damage to the sample is discussed in the context of the velocity dependence of the measured lateral force on the AFM tip.

A new detection system for extremely small vertically mounted cantilevers.

Detection techniques currently used in scanning force microscopy impose limitations on the geometrical dimensions of the probes and, as a consequence, on their force sensitivity and temporal response. A new technique, based on scattered evanescent electromagnetic waves (SEW), is presented here that can detect the displacement of the extreme end of a vertically mounted cantilever. The resolution of this method is tested using different cantilever sizes and a theoretical model is developed to maximize the detection sensitivity. The applications presented here clearly show that the SEW detection system enables the use of force sensors with sub-micron size, opening new possibilities in the investigation of biomolecular systems and high speed imaging. Two types of cantilevers were successfully tested: a high force sensitivity lever with a spring constant of 0.17 pN nm(-1) and a resonant frequency of 32 kHz; and a high speed lever with a spring constant of 50 pN nm(-1) and a resonant frequency of 1.8 MHz. Both these force sensors were fabricated by modifying commercial microcantilevers in a focused ion beam system. It is important to emphasize that these modified cantilevers could not be detected by the conventional optical detection system used in commercial atomic force microscopes.