Tailoring precursors for deposition: synthesis, structure, and thermal studies of cyclopentadienylcopper(i) isocyanide complexes.

We report here the synthesis and characterization of a family of copper(I) metal precursors based around cyclopentadienyl and isocyanide ligands. The molecular structures of several cyclopentadienylcopper(I) isocyanide complexes have been unambiguously determined by single-crystal X-ray diffraction analysis. Thermogravimetric analysis of the complexes highlighted the isopropyl isocyanide complex [(η(5)-C5H5)Cu(CN(i)Pr)] (2a) and the tert-butyl isocyanide complex [(η(5)-C5H5)Cu(CN(t)Bu)] (2b) as possible copper metal chemical vapor deposition (CVD) precursors. Further modification of the precursors with variation of the substituents on the cyclopentadienyl ligand system (varying between H, Me, Et, and (i)Pr) has allowed the affect that these changes would have on features such as stability, volatility, and decomposition to be investigated. As part of this study, the vapor pressures of the complexes 2b, [(η(5)-MeC5H4)Cu(CN(t)Bu)] (3b), [(η(5)-EtC5H4)Cu(CN(t)Bu)] (4b), and [(η(5)-(i)PrC5H4)Cu(CN(t)Bu)] (5b) over a 40-65 °C temperature range have been determined. Low-pressure chemical vapor deposition (LP-CVD) was employed using precursors 2a and 2b to synthesize thin films of metallic copper on silicon, gold, and platinum substrates under a H2 atmosphere. Analysis of the thin films deposited onto both silicon and gold substrates at substrate temperatures of 180 and 300 °C by scanning electron microscopy and atomic force microscopy reveals temperature-dependent growth features: Films grown at 300 °C are continuous and pinhole-free, whereas films grown at 180 °C consist of highly crystalline nanoparticles. In contrast, deposition onto platinum substrates at 180 °C shows a high degree of surface coverage with the formation of high-density, continuous, and pinhole-free thin films. Powder X-ray diffraction and X-ray photoelectron spectroscopy (XPS) both show the films to be high-purity metallic copper.

Antiproliferative and apoptosis-inducing activity of an oxidovanadium(IV) complex with the flavonoid silibinin against osteosarcoma cells.

Flavonoids are a large family of polyphenolic compounds synthesized by plants. They display interesting biological effects mainly related to their antioxidant properties. On the other hand, vanadium compounds also exhibit different biological and pharmacological effects in cell culture and in animal models. Since coordination of ligands to metals can improve or change the pharmacological properties, we report herein, for the first time, a detailed study of the mechanisms of action of an oxidovanadium(IV) complex with the flavonoid silibinin, Na2[VO(silibinin)2]·6H2O (VOsil), in a model of the human osteosarcoma derived cell line MG-63. The complex inhibited the viability of osteosarcoma cells in a dose-dependent manner with a greater potency than that of silibinin and oxidovanadium(IV) (p < 0.01), demonstrating the benefit of complexation. Cytotoxicity and genotoxicity studies also showed a concentration effect for VOsil. The increase in the levels of reactive oxygen species and the decrease of the ratio of the amount of reduced glutathione to the amount of oxidized glutathione were involved in the deleterious effects of the complex. Besides, the complex caused cell cycle arrest and activated caspase 3, triggering apoptosis as determined by flow cytometry. As a whole, these results show the main mechanisms of the deleterious effects of VOsil in the osteosarcoma cell line, demonstrating that this complex is a promising compound for cancer treatments.

The Simons Observatory: Cryogenic half wave plate rotation mechanism for the small aperture telescopes.

We present the requirements, design, and evaluation of the cryogenic continuously rotating half-wave plate (CHWP) for the Simons Observatory (SO). SO is a cosmic microwave background polarization experiment at Parque Astronómico de Atacama in northern Chile that covers a wide range of angular scales using both small (⌀0.42 m) and large (⌀6 m) aperture telescopes. In particular, the small aperture telescopes (SATs) focus on large angular scales for primordial B-mode polarization. To this end, the SATs employ a CHWP to modulate the polarization of the incident light at 8 Hz, suppressing atmospheric 1/f noise and mitigating systematic uncertainties that would otherwise arise due to the differential response of detectors sensitive to orthogonal polarizations. The CHWP consists of a 505 mm diameter achromatic sapphire HWP and a cryogenic rotation mechanism, both of which are cooled down to ∼50 K to reduce detector thermal loading. Under normal operation, the HWP is suspended by a superconducting magnetic bearing and rotates with a constant 2 Hz frequency, controlled by an electromagnetic synchronous motor. We find that the number of superconductors and the number of magnets that make up the superconducting magnetic bearing are important design parameters, especially for the rotation mechanism's vibration performance. The rotation angle is detected through an angular encoder with a noise level of 0.07 µrad s. During a cooldown process, the rotor is held in place by a grip-and-release mechanism that serves as both an alignment device and a thermal path. In this paper, we provide an overview of the SO SAT CHWP: its requirements, hardware design, and laboratory performance.

Synthesis, characterization and self-assembly of biosurfactants based on hydrophobically modified inulins.

Biosurfactants have been synthesized using a low energy, environmentally friendly process by the derivatization of inulin with octenyl (OSA) and dodecenyl (DDSA) succinic anhydrides in aqueous solution. The inulin and its derivatives have been characterized using gel permeation chromatography/multi angle light scattering (GPC/MALLS), high-performance anion exchange chromatography with pulsed amperometric detection (HPAEC-PAD), Fourier transform infrared spectroscopy (FTIR), and NMR, and the reaction efficiency was found to be between 59 and 95%. The efficiency was generally higher for OSA derivatives compared to DDSA derivatives. The hydrophobic derivatives were found to aggregate in solution and the critical aggregation concentration (CAC) was determined using dye solubilization, surface tension, dynamic light scattering (DLS), and conductivity. There was reasonable agreement in the CAC values obtained by the different techniques except for conductivity. It was found that the CAC decreased with increasing alkenyl chain length and degree of modification, and the values were significantly lower for the DDSA derivatives compared to the OSA derivatives. GPC elution profiles for the DDSA-inulin using 12 mol % reagent confirmed the presence of aggregates with a molecular mass of ∼2.5 × 10(6) g/mol and a radius of gyration of ∼25 nm corresponding to ∼550 inulin molecules. DLS study was undertaken to determine the hydrodynamic radius, and values obtained for the DDSA (12%) derivative were 30 nm in both water and 0.1 M sodium nitrate, while for the OSA (12%) derivative values of 13 and 7 nm were obtained. The derivatives have potential application in the stabilization of particulate dispersions and emulsions and also in the encapsulation and delivery of drugs.

Selective Visualization of Live Intestinal Parasites in Stool Specimens Without Purification.

PURPOSE: Microscopic observation of live parasites in the stool is an important diagnostic tool in human and veterinary medicine. Because of the presence of large amounts of contaminating organic matter, microscopic analysis must be preceded by time-consuming pre-purification steps. Transmission-through-dye (TTD) optical microscopy obviates this problem. The purpose of this study is to illustrate the use of TTD for the analysis of stool samples. METHODS: TTD imaging is based on the exclusion of a strongly absorbing dye by living cells. A food colorant Acid Blue 9 (AB9) is added to a fecal suspension, and the sample is observed under transmitted illumination through a 630 nm bandpass filter. AB9 strongly absorbs red light, and it comes out of the sample significantly attenuated. However, if a viable cell of any origin is present in the sample, it excludes the dye and reduces the depth of the light-absorbing layer. RESULTS: Live cells or eggs appear bright red on a dark background, while most of the organic contaminants remain dark. The method has been demonstrated on schistosomes, hookworms, giardia, yeast, and other organisms. CONCLUSION: TTD dramatically increases the visibility of live parasites and permits their direct observation in a fecal suspension. TTD can be enabled on any microscope by simply adding a red filter.

Metal organic chemical vapour deposition of vertically aligned ZnO nanowires using oxygen donor adducts.

Vertically aligned zinc oxide (ZnO) nanowires (NWs) have been grown by liquid injection Metal Organic Chemical Vapour Deposition, using oxygen donor adducts of Me2Zn. The growth and characterisation of the nanowires grown using [Me2Zn(L)] where L = monodentate ethers, tetrahydrofuran (C4H8O) (1), tetrahydropyran (C5H10O) (2), furan (C4H4O) (3) and the bidentate ethers, 1,2-dimethoxyethane (C4H12O2,) (4) 1,4-dioxane (C4H8O2) (5) and 1,4-thioxane (C4H8SO) (6) is discussed. Single crystal X-ray structures of (4), (5), (6) have been established and are included here. The ZnO NWs were deposited in the absence of a seed catalyst on Si(111) and F-doped SnO2/glass substrates over the temperature range 350-600 degrees C. X-ray diffraction (XRD) data shows that the nanowires grown from all adduct precursors were deposited in the wurtzitic phase.

Comparing the needs of health professional and peer cancer support group facilitators in an Australian context.

This study explored the perceived needs of health professional and peer facilitators of cancer support groups. Participants were facilitators of support groups affiliated with The Cancer Council Victoria (Australia). Facilitators completed questionnaires assessing their experience of support group facilitation, including training and support needs. Data from health professional and peer facilitators (n= 74) were analysed in this paper. The majority of facilitators (88%) were female; 57% had run their group for more than 3 years, and 47% reported between 11 and 20 people attended each group. Although results showed the characteristics of support groups are broadly similar for peers and professionals, there were some distinct differences in perceived needs. Health professional facilitators were more likely than peers to regard training as valuable and beneficial to their role. In addition, health professionals more frequently reported needing debriefing as well as more difficulty accessing debriefing than cancer peers. This study builds on the small body of literature exploring the experiences of cancer support group facilitators. Given the experiences and needs of health professional and peer facilitators may differ, it may be relevant to tailor training and support so that it meets the needs of both health professionals and cancer peers.

Electrostatic interaction and complex formation between gum arabic and bovine serum albumin.

The interaction of gum arabic (GA) and bovine serum albumin (BSA) has been investigated through turbidity and light scattering intensity measurements and by the use of dynamic light scattering, laser Doppler velocimetry, and isothermal titration calorimetry. It has been shown that GA and BSA can form soluble and insoluble complexes depending on the solution pH and the mixing ratio and is a function of the net charge on the complex. Soluble complexes were obtained when the electrophoretic mobility was greater than ±1. 5 µm s(-1) V(-1) cm(-1). Changes in the value of the isoelectric point of the complexes with mixing ratio and isothermal titration calorimetric data indicated that complexes formed at pHs 3 and 4 consisted of ∼60 BSA molecules for every GA molecule, while at pH 5 there were ∼10 BSA molecules per GA molecule. Calorimetric studies also indicated that the interaction occurred in two stages at both pH 3 and pH 4, but that the nature of the interaction at these two pH values was significantly different. This was attributed to differences in the relative magnitude of the positive and negative charges on the BSA and GA, respectively, and possibly due to changes in the BSA conformation. The fact that there is an interaction at pH 5, which is above the isoelectric point of the BSA, is due to the interaction of the carboxylate groups on the GA with positive patches on the BSA or to the charge regulation of the protein-polysaccharide system brought about by changes in dissociation equilibria. Complexation is reduced as the ionic strength of the solvent increases and is prevented at a NaCl concentration of 120 mM.

Liquid injection atomic layer deposition of silver nanoparticles.

Silver nanoparticles are being developed for applications in plasmonics, catalysts and analytical methods, amongst others. Herein, we demonstrate the growth of silver nanoparticles using an atomic layer deposition (ALD) process for the first time. The silver was deposited from pulses of the organometallic precursor (hfac)Ag(1,5-COD) ((hexafluoroacetylacetonato)silver(I)(1,5-cyclooctadiene)) dissolved in a 0.1 M toluene solution. Catalytic oxidative dehydrogenation of the silver was achieved using intermittent pulses of propanol. The effect of substrate temperature on the size and distribution of nanoparticles has been investigated over the temperature range 110-150 degrees C. Transmission electron microscopy reveals that the nanoparticles consist of face centred cubic, facetted silver crystallites. The localized surface plasmon modes of the nanoparticles have been investigated using electron energy loss spectroscopy mapping. The distributions of plasmons within the ALD nanoparticles are comparable to those grown by solution methods. Both dipolar and quadrupolar resonant modes are observed, which is consistent with previous discrete dipole approximation models. Energy loss mapping of a loss feature at 8.1 eV reveals that it correlates with the bulk or volume region of the silver nanoparticles investigated here.

Third-body abrasive wear challenge of 32 mm conventional and 44 mm highly crosslinked polyethylene liners in a hip simulator model.

Hip simulator studies have shown that wear in the polyethylene liners used for total hip replacements increased with the larger-diameter femoral balls and could also be exacerbated by third-body abrasion. However, they also indicated that the more highly cross-linked polyethylene (HXPE) bearings were more wear resistant than conventional polyethylene (CXPE) bearings. Unfortunately the HXPE bearings appeared to be particularly sensitive to adverse wear conditions. One simulator study in particular indicated that poly(methyl methacrylate) (PMMA) debris increased wear sixfold by means of two-body abrasive interactions rather than the supposed third-body abrasion or roughening effects of the Co-Cr surfaces. There has been no confirmation of such novel theories. Therefore the goal of this study was to investigate the sensitivity of large-diameter HXPE bearings to the third-body PMMA wear challenge in a hip simulator model. An orbital hip simulator was used in standard test mode with a physiological load profile. The 32 mm control liners were machined from moulded GUR1050 and gamma irradiated to 35 kGy under nitrogen (CXPE). The 44 mm liners were also from moulded blanks, gamma irradiated to 75 kGy, machined to shape, given a proprietary heat treatment, and sterilized by gas plasma (HXPE). As in the published simulator model, the study was conducted in three phases. In phase 1, all cups were run in standard ('clean') lubricant for 1.5 x 10(6) cycles duration. In phase 2, three CXPE cups and six HXPE cups were run for 2 x 10(6) cycles with a slurry of PMMA particles added to the lubricant. In phase 3, the implants were again run in 'clean' lubricant for 2 x 10(6) cycles duration. In addition, three HXPE cups were run as wear controls for 5.5 x 10(6) cycles duration in clean lubricant. In phase-1, the HXPE liners demonstrated twelvefold reduced wear compared with the CXPE controls. The 32 mm and 44 mm Co-Cr balls were judged of comparable roughnesses. However, the surface finish of HXPE liners was superior to that of CXPE liners. In phase-2 abrasion, wear rates increased sixfold and eighty-fold for CXPE and HXPE bearings respectively. These data confirmed that HXPE bearings were particularly sensitive to 'severe' test modes. The Co-Cr balls revealed numerous surface patches representing transferred PMMA with average transient roughness increased to 25 nm and 212 nm for the 32 mm and 44 mm balls respectively. These PMMA patches produced an aggressive two-body abrasion wear of the polyethylene. After cleaning, the ball roughness returned to near normal. Therefore the Co-Cr roughness was not an issue in this severe test mode. In phase 3, the wear decreased to near the index values of phase 1, while liner roughness dropped by more than 90 per cent. The control CXPE liners now demonstrated twice the wear of the HXPE, as would be predicted comparing the diameter and cross-linking algorithms. No previous study has correlated polyethylene roughness profiles to wear performance. In phase 2, PMMA abrasion created significant damage to the polyethylene surfaces. The average roughness Sa of CXPE liners increased to 3.6 microm, a twenty-four-fold increase with some scratches up to 40 microm deep. The HXPE roughness also increased but only to 1.5 microm, a ninefold increase. The scratch indices Sz and Sp for HXPE surfaces were also 50 per cent less severe than on CXPE surfaces. However, within 2 x 10(6) cycles duration of phase 3, all liners had recovered to virtually their original surface finish in phase 1. In all test phases, the surface finish of the HXPE liners remained superior to control liners. These experimental data confirmed many of the results from the previous simulator study with the PMMA abrasion models. Thus the 44 mm liners appeared an excellent clinical alternative to the smaller ball designs used in total hip replacements.

The interfacial, emulsification and encapsulation properties of hydrophobically modified inulin.

Octenyl- and dodecenyl succinic anhydride derivatives (OSA- and DDSA-) of inulin have been synthesised and their solution and interfacial properties have been determined and compared to a commercially available alkylated inulin, Inutec SP1. All samples formed micellar aggregates in solution above a critical concentration (critical aggregation concentration) and were able to 'dissolve' a hydrophobic dye. They were also able to form stable oil-in-water (O/W) emulsions as assessed by measurements of their droplet size as a function of time. DDSA-inulin with a high degree of substitution was found to be effective at encapsulating beta carotene using the solvent evaporation method which yielded a solid which dissolved readily in simulated gastric fluid. The results confirm the potential application of these materials in a number of areas including, drug delivery, pharmaceuticals, neutraceuticals, cosmetics and personal care.

Synthesis of cationic alkylated chitosans and an investigation of their rheological properties and interaction with anionic surfactant.

Two methods were used to alkylate high MW chitosan with glycidyltrimethylammonium chloride (GTAC) in order to produce chitosan derivatives that are water-soluble throughout the pH range. In addition, a novel chitosan derivative was created by alkylating one of the products with the GTAC analogue Quab 342 containing C12 alkyl chains. The phase behaviour and rheological characteristics of the chitosan derivatives were studied in the presence of anionic surfactant. The derivatives were found to form soluble complexes at low and high SDS concentrations and that the Quab 342 derivative was able to form gels.

A chronic histopathological and electrophysiological analysis of a rodent hypoxic-ischemic brain injury model and its use as a model of epilepsy.

Ischemic brain injury is one of the leading causes of epilepsy in the elderly, and there are currently no adult rodent models of global ischemia, unilateral hemispheric ischemia, or focal ischemia that report the occurrence of spontaneous motor seizures following ischemic brain injury. The rodent hypoxic-ischemic (H-I) model of brain injury in adult rats is a model of unilateral hemispheric ischemic injury. Recent studies have shown that an H-I injury in perinatal rats causes hippocampal mossy fiber sprouting and epilepsy. These experiments aimed to test the hypothesis that a unilateral H-I injury leading to severe neuronal loss in young-adult rats also causes mossy fiber sprouting and spontaneous motor seizures many months after the injury, and that the mossy fiber sprouting induced by the H-I injury forms new functional recurrent excitatory synapses. The right common carotid artery of 30-day old rats was permanently ligated, and the rats were placed into a chamber with 8% oxygen for 30 min. A quantitative stereologic analysis revealed that the ipsilateral hippocampus had significant hilar and CA1 pyramidal neuronal loss compared with the contralateral and sham-control hippocampi. The septal region from the ipsilateral and contralateral hippocampus had small but significantly increased amounts of Timm staining in the inner molecular layer compared with the sham-control hippocampi. Three of 20 lesioned animals (15%) were observed to have at least one spontaneous motor seizure 6-12 months after treatment. Approximately 50% of the ipsilateral and contralateral hippocampal slices displayed abnormal electrophysiological responses in the dentate gyrus, manifest as all-or-none bursts to hilar stimulation. This study suggests that H-I injury is associated with synaptic reorganization in the lesioned region of the hippocampus, and that new recurrent excitatory circuits can predispose the hippocampus to abnormal electrophysiological activity and spontaneous motor seizures.

The orientationally controlled assembly of genetically modified enzymes in an amperometric biosensor.

A novel, nitroreductase (NTR) containing a sequence of six cysteine amino acids, enabling strong thiolate bonds to form on a gold electrode surface without the loss of enzyme activity, was genetically engineered. The enzyme was directly immobilised at a gold electrode without the need for pre-treatment of the surface with a self-assembled monolayer or a conducting polymer. The ensemble was used to develop an amperometric biosensor for the detection of explosives containing nitroaromatic compounds. Preliminary results demonstrate detection levels down to 100 parts per trillion, signifying tremendous promise towards an in situ sensor for the detection of explosives.

Biophotonic Tools in Cell and Tissue Diagnostics.

In order to maintain the rapid advance of biophotonics in the U.S. and enhance our competitiveness worldwide, key measurement tools must be in place. As part of a wide-reaching effort to improve the U.S. technology base, the National Institute of Standards and Technology sponsored a workshop titled "Biophotonic tools for cell and tissue diagnostics." The workshop focused on diagnostic techniques involving the interaction between biological systems and photons. Through invited presentations by industry representatives and panel discussion, near- and far-term measurement needs were evaluated. As a result of this workshop, this document has been prepared on the measurement tools needed for biophotonic cell and tissue diagnostics. This will become a part of the larger measurement road-mapping effort to be presented to the Nation as an assessment of the U.S. Measurement System. The information will be used to highlight measurement needs to the community and to facilitate solutions.

Synthesis, characterisation and physicochemical properties of hydrophobically modified inulin using long-chain fatty acyl chlorides.

A series of inulin derivatives were synthesized in aqueous solution using acyl chlorides with varying alkyl chain length (C10-C16). They were characterised using a number of techniques including MALDI TOF-MS, 1H NMR and FTIR and their degree of substitution determined. The solution properties of the hydrophobically modified inulins were investigated using dye solubilisation and surface tension and it was confirmed that the molecules aggregated in solution above a critical concentration (critical aggregation concentration, CAC). The value of the CAC was found to be reasonably consistent between the different techniques and was shown to decrease with increasing hydrophobe chain length. It was found that the C10, C12 and C14 derivatives formed stable oil-in-water emulsions and the emulsion droplet size decreased with increasing alkyl chain length. The C16 derivative was not able to produce stable oil-in-water emulsions; however, it was able to form stable water-in-oil emulsions. The fact that the derivatives are able to form micellar-like aggregates and stabilise emulsions makes them suitable candidates for the encapsulation and delivery of active compounds with potential application in food, cosmetic, personal care and pharmaceutical formulations.

On the interaction of vanadium species with meso-2,3-dimercaptosuccinic acid.

The interaction of the VO2+ cation with meso-2,3-dimercaptosuccinic acid (DMSA) was investigated by electron absorption spectroscopy in aqueous solution at different pH values. The spectral behavior, complemented with a spectrophotometric titration, shows the generation of a [VO(DMSA)2]2- complex in which the oxocation interacts with two pairs of deprotonated -SH groups of the acid. It was also found that DMSA rapidly reduces VO3- to VO2+, which might be chelated by an excess of the acid. DMSA can also produce the partial reduction of a V2O5 suspension at pH=5.2. The results of this study suggest that DMSA might be a potentially useful detoxification agent for vanadium.

'Severe' wear challenge to 'as-cast' and 'double heat-treated' large-diameter metal-on-metal hip bearings.

The wear generation of double-heat-treated and as-cast large-diameter metal-on-metal (MOM) hip bearings was investigated using standard- and 'severe'-gait simulations. The test hypothesis was that double heat treatment would change MOM hip wear compared with the as-cast condition. Two groups of high-carbon MOM bearings of 40 mm diameter were manufactured and subjected to either hot isostatic pressing (HIP) and solution annealing (SA) or no heat treatment (as cast). The results showed no statistical difference between the two groups under both running-in and steady state conditions. Even under the most 'severe'-gait simulation published to date, the mean volumetric wear rates were 2.9 and 3.9 mm3 per 10(6) cycles for the HIP-SA and as-cast bearings respectively, showing a ten-fold increase in wear compared with walking. These differences were not statistically different; therefore our hypothesis was negated. Changes in alloy microstructure do not appear to influence the wear behaviour of high-carbon cast MOM articulations with similar chemical compositions. This is in sharp contrast with the published significance of bearing diameter and radial clearance on the wear of MOM hip bearings.

Metal-on-metal hip simulator study of increased wear particle surface area due to 'severe' patient activity.

This study investigated changes in metal-on-metal (MOM) hip wear and wear particle characteristics arising from a more aggressive patient activity level compared with normal walking. The test hypothesis was that 'severe'-gait conditions will change wear, wear particle sizes, and morphology owing to a decline in joint lubrication. Four carbon MOM hip bearings 40 mm high were subjected to normal-walking and fast-jogging simulations in an orbital hip joint simulator with 25 per cent alpha-calf serum as a lubricant. Co-Cr-Mo wear particles were extracted using an enzymatic method, and prolate ellipsoid equations were used to estimate particle volume and surface area. Fast-jogging simulations generated a sevenfold increase in volumetric wear, a 33 per cent increase in mean wear particle size, and a threefold increase in the number of larger (needle) particles compared with walking. This resulted in a twentyfold increase in total wear particle surface area per 10(6) cycles compared with walking, thereby confirming our hypothesis. The clinical significance of this result suggests that highly active MOM patients may exhibit greater ion release than less active patients.

Purification of the proteinase from group B streptococci that inactivates human C5a.

We previously reported that group B streptococci (GBS) possess a cell-associated activity that inactivates the chemotactic activity generated in zymosan-activated serum by cleaving a specific site within the carboxy termini of C5a and C5adesarg. This inactivates the major chemoattractants for neutrophils that are generated when serum complement is activated. We now report the isolation of the enzyme responsible for the proteolytic cleavage of C5a. Treatment of GBS with mutanolysin, an endo-N-acetyl muramidase, released activity from GBS which destroyed the functional activity of C5a. The soluble activity was purified to homogeneity by hydroxyapatite, ion-exchange and gel-filtration chromatography. Analysis by SDS-PAGE showed that the enzyme (GBS C5a-ase) has an Mr of approx. 120,000. The GBS C5a-ase appears to be a serine esterase on the basis of its sensitivity to di-isopropyl fluorophosphate. This enzyme is distinct from the C5a-cleaving enzyme produced by group A streptococci, since the two bacterial products migrate differently on SDS-PAGE, and lack antigenic cross reactivity. This enzyme may play a role in the pathogenesis of group B streptococcal disease through its ability to rapidly inactivate the potent neutrophil agonist, C5a, at sites of infection.