Passive Inclination Sensor Based on a Patch Antenna with a Reconfigurable Water Load.

In order to ensure the safety and preserve the value of historical buildings, inclination is an essential parameter during the continuous structural health monitoring process. However, the wire and price of a traditional sensor limit application. This paper proposes a low-cost inclination sensor based on a patch antenna with a reconfigurable water load. Only the water directly on the antenna is considered effective. The different volume of the effective water load, which is determined by the inclination of the attached surface, will affect the effective permittivity of the dielectric plate of the patch antenna, further causing a variation in the resonant frequency. Therefore, the proposed antenna sensor can monitor the inclination of the attached surface by interrogating the resonant frequency. The working mechanism is first clarified by theoretically investigating the relationship between the dielectric properties and the inclination of the covering medium. The antenna sensor is then simulated using High-Frequency Structure Simulator ver.15 (HFSS 15), which helps to determine geometric parameters and confirm accuracy and sensitivity. An experiment has been conducted based on the design verified in the simulation. The inclination detection shows a correlation coefficient of 0.9771 with a sensitivity of 7.92 MHz/°, indicating a potential for real application.

A Capacitively-Fed Inverted-F Antenna for Displacement Detection in Structural Health Monitoring.

This paper presents a capacitive displacement sensor based on a capacitively fed inverted-F antenna (CFIFA) for displacement detection. The sensor is composed of a grounded L-shape patch and a rectangular upper patch, forming a capacitor between them. The asymmetric dipole model is adopted to explain the frequency shift and current distribution of the proposed antenna sensor at its first-order resonance. The numerical simulation of the CFIFA using the Ansoft high-frequency structure simulator (HFSS) software is carried out to optimize the dimensional parameters, allowing the antenna to perform better. Two sets of CFIFAs are fabricated and tested for verification. Results show that the CFIFA has a good linear relationship between its first resonant frequency and the relative displacement, and is capable of a long range of displacement measuring.

Long-Range Displacement Meters Based on Chipped Circular Patch Antenna.

This paper presents a passive wireless long-range displacement sensor that is based on the circular patch antenna, and the detecting range of the sensor can be customized. The sensor consists of a chipped circular antenna with two opened rectangular windows, a substrate, and a ground plate with a sloping channel. No bonding between the antenna and the ground plate allows for the chipped antenna to slide along the sloping channel. The channel will drive the current flow on the plate once the chip is activated, increasing the effective electrical length and, consequently, decreasing the resonant frequency of the circular antenna. The sensing mechanism equates the measuring displacement to the relative movement of the antenna with respect to the ground that achieves the measurement of long-range displacement and, thus, the proposed sensor can avoid stress damage to the antenna due to excessive deformation. Three different range sensors were simulated in the the Ansoft high frequency structure simulator (HFSS). The results show that the resonance frequency of the antenna has a linear relationship with the varying chute depth beneath the chip. Three sensors were fabricated, and the experimental results also validated that the sensitivity of the sensor can be adjusted.

A Displacement Sensor Based on a Normal Mode Helical Antenna.

This paper presents a passive displacement sensor based on a normal mode helical antenna. The sensor consists of an external helical antenna and an inserting dielectric rod. First, the perturbation theory is adopted to demonstrate that both the electric intensity and magnetic intensity have a noticeable gradient change within the in-and-out entrance of the helical antenna, which will cause the sensor to experience a resonant frequency shift. This phenomenon was further verified by numerical simulation using the Ansoft high frequency structure simulator (HFSS), and results show the linear correlation between the retrieved resonant frequency and the displacement. Two sets of proposed sensors were fabricated. The experiments validated that the resonant frequency shifts are linearly proportional to the applied displacement, and the sensing range can be adjusted to accommodate the user's needs.

A Passive Wireless Crack Sensor Based on Patch Antenna with Overlapping Sub-Patch.

Monolithic patch antennas for deformation measurements are designed to be stressed. To avoid the issues of incomplete strain transfer ratio and insufficient bonding strength of stressed antennas, this paper presents a passive wireless crack sensor based on an unstressed patch antenna. The rectangular radiation patch of the proposed sensor is partially covered by a radiation sub-patch, and the overlapped length between them will induce the resonate frequency shift representing the crack width. First, the cavity model theory is adopted to show how the resonant frequencies of the crack sensor are related to the overlapped length between the patch antenna and the sub-patch. This phenomenon is further verified by numerical simulation using the Ansoft high-frequency structure simulator (HFSS), and results show a sensitivity of 120.24 MHz/mm on average within an effective measuring range of 1.5 mm. One prototype of proposed sensor was fabricated. The experiments validated that the resonant frequency shifts are linearly proportional to the applied crack width, and the resolution is suitable for crack width measuring.

Rhodium-Catalyzed Branched and Enantioselective Direct α-Allylic Alkylation of Simple Ketones with Alkynes.

Herein, we report the first direct branched-selective α-allylic alkylation of simple ketones with alkynes under rhodium and secondary amine cooperative catalysis. Through a rhodium-hydride-catalyzed allylic substitution pathway, a series of valuable γ,δ-unsaturated ketones are obtained with excellent regioselectivity in an atom-economic and byproduct-free manner. With a chiral BIPHEP ligand, high enantioselectivity has been achieved for this transformation.

[The efficacy of bronchial artery infusion chemotherapy combined with immunotherapy for lung cancer with malignant hydrothorax].

BACKGROUND: To explore the therapeutic effect of bronchial artery infusion chemotherapy combined with immunotherapy for lung cancer with malignant hydrothorax. METHODS: Seventy-five lung cancer patients with malignant hydrothorax were randomly divided into the two groups: 38 patients were given intrathoracic chemotherapy and bronchial artery infusion chemotherapy combined with immunotherapy as observing group; 37cases only received intrathoracic chemotherapy as control group. Chi-square assay was performed to analyze the efficacy (responses for lung cancer and hydrothorax control) after the first course of treatment and the 1-, 2-year survival rates in the two groups. RESULTS: After the first course of treatment, the total responses for lung cancer were 31.58% (12/38) and 5.41% (2/37) in the observing group and control group (Chi-square=8.46, P < 0.01) respectively ; and responses for hydrothorax control were 86.84% and 64.86% respectively (Chi-square= 4.96, P <0.05). The 1- and 2-year survival rates in the observing group were 65.79% (25/38) and 26.32% (10/38) respectively, which were significantly higher than those of the control group (40.54% and 5.41%) respectively (Chi-square=4.80, P <0.05; Chi-square=6.10, P <0.05). CONCLUSIONS: The intrathoracic chemotherapy combined with bronchial artery infusion chemotherapy and immunotherapy is quite effective in the treatment of lung cancer with malignant hydrothorax.