Versatile Application of TiO2@PDA Modified Filter Paper for Oily Wastewater Treatment.

Although membrane separation technology has been widely used in the treatment of oily wastewater, the complexity and high cost of the membrane preparation, as well as its poor stability, limit its further development. In this study, via the vacuum-assisted suction filtration method, polydopamine (PDA)-coated TiO2 nanoparticles were tightly attached and embedded on both sides of laboratory filter paper (FP). The resultant FP possessed the typical wettability of high hydrophilicity in the air with the water contact angle (WCA) of 28°, superoleophilicity with the oil contact angle (OCA) close to 0°, underwater superoleophobicity with the underwater OCA greater than 150°, and superhydrophobicity under the water with the underoil WCA over 150° for five kinds of organic solvents (carbon tetrachloride, toluene, n-hexane, n-octane, and iso-octane). The separation efficiency of immiscible oil/water, oil-in-water, and water-in-oil emulsions using the modified FP is higher than 99%. After 17 cycles of emulsion separation, a high separation efficiency of 99% was still maintained for the FP, along with good chemical and mechanical stability. In addition, successful separation and purification were also realized for the oil-in-water emulsion that contained the methylene blue (MB) dye, along with the complete degradation of MB in an aqueous solution under UV irradiation.

Robust Superhydrophobic Brass Mesh with Electrodeposited Hydroxyapatite Coating for Versatile Applications.

A robust superhydrophobic brass mesh was fabricated based on a low-energy surface and a roughness on the nano/micro-meter scale. It was carried out by the forming of hydroxyapatite (HP) coatings on its surface through a constant current electro-deposition process, followed by immersion in fluoroalkylsilane solution. Surface morphology, composition and wetting behavior were investigated by field-emission scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), high speed camera, and contact angle goniometer. Under optimal conditions, the resulting brass mesh exhibited superhydrophobicity, excellent anti-corrosion (η = 91.2%), and anti-scaling properties. While the surfactant liquid droplets of tetradecyl trimethyl ammonium bromide (TTAB) with different concentration were dropped on the superhydrophobic surface, maximum droplet rebounding heights and different contact angles (CAs) were observed and measured from side-view imaging. The plots of surfactant-concentration-maximum bounding height/CA were constructed to determine its critical-micelle-concentration (CMC) value. Close CMC results of 1.91 and 2.32 mM based on the determination of maximum rebounding height and CAs were obtained. Compared with its theoretical value of 2.1 mM, the relative errors are 9% and 10%, respectively. This indicated that the novel application based on the maximum rebounding height could be an alternative approach for the CMC determination of other surfactants.

Superwetting Stainless Steel Mesh Used for Both Immiscible Oil/Water and Surfactant-Stabilized Emulsion Separation.

The design and fabrication of advanced membrane materials for versatile oil/water separation are major challenges. In this work, a superwetting stainless steel mesh (SSM) modified with in situ-grown TiO2 was successfully prepared via one-pot hydrothermal synthesis at 180 °C for 24 h. The modified SSM was characterized by means of scanning electron microscopy, energy spectroscopy, and X-ray photoelectron spectroscopy analysis. The resultant SSM membrane was superhydrophilic/superoleophilic in air, superoleophobic underwater, with an oil contact angle (OCA) underwater of over 150°, and superhydrophobic under oil, with a water contact angle (WCA) as high as 158°. Facile separation of immiscible light oil/water and heavy oil/water was carried out using the prewetting method with water and oil, respectively. For both "oil-blocking" and "water-blocking" membranes, the separation efficiency was greater than 98%. Also, these SSMs wrapped in TiO2 nanoparticles broke emulsions well, separating oil-in-water and oil-in-water emulsions with an efficiency greater than 99.0%. The as-prepared superwetting materials provided a satisfactory solution for the complicated or versatile oil/water separation.