Mechanistic insights into promoted dewaterability, drying behaviors and methane-producing potential of waste activated sludge by Fe2+-activated persulfate oxidation.

Sludge management represents a critical challenge because of complex compositions and poor dewaterability. Fe2+-activated persulfate oxidation (Fe2+/S2O82-) is an effective, and widely investigated method for enhancing sludge dewatering. However, the potential effects of Fe2+/S2O82- on sludge drying efficiency, anaerobic biodegradation behaviors and potential recycling of sludge residua are not yet well-known. In this study, a new sludge disposal route (step i: enhanced dewatering via Fe2+/S2O82-, and step ii: drying-incineration or anaerobic digestion) was proposed and appraised comprehensively. Results showed that Fe2+/S2O82- oxidation destroyed extracellular polymeric substances, lysed sludge cells and enhanced the dewaterability greatly. Capillary suction time and mechanical filtration time at 2.0/1.6 mmol-Fe2+/S2O82-/g-VS decreased by 88.0% and 79.6%, respectively. Moreover, 89.8% of micro-pollutants (e.g., methylbenzene, ethylbenzene, p-m-xylene and o-xylene) in sludge were removed. Besides, the pretreatment was able to alter sludge drying behaviors and methane-producing potential. Pretreated sludge exhibited faster drying rate and shorter lag-time for methane production. Incineration residua of dewatered sludge could be re-coupled with S2O82- as the conditioner to enhance sludge dewaterability, thereby reducing the chemical input and disposal cost. This study provides a novel, self-sustainable strategy for sludge management, reutilization and final safe disposal.

Thermophilic Solid-State Anaerobic Digestion of Corn Straw, Cattle Manure, and Vegetable Waste: Effect of Temperature, Total Solid Content, and C/N Ratio.

Thermophilic solid-state anaerobic digestion (SS-AD) of agricultural wastes, i.e., corn straw, cattle manure, and vegetable waste, was carried out in this study. The effects of temperature (40-60°C), initial solid content (ISC, 17.5-32.5%), and C/N ratio (15-32 : 1) on biogas production were evaluated using a Box-Behnken experimental design (BBD) combined with response surface methodology (RSM). The results showed that optimization of process parameters is important to promote the SS-AD performance. All the factors, including interactive terms (except the ISC), were significant in the quadratic model for biogas production with SS-AD. Among the three operation parameters, the C/N ratio had the largest effect on biogas production, followed by temperature, and a maximum biogas yield of 241.4 mL gVS-1 could be achieved at 47.3°C, ISC = 24.81%, and C/N = 22.35. After 20 d of SS-AD, the microbial community structure under different conditions was characterized by high-throughput sequencing, showing that Firmicutes, Bacteroidetes, Chloroflexi, Synergistetes, and Proteobacteria dominated the bacterial community, and that Firmicutes had a competitive advantage over Bacteroidetes at elevated temperatures. The biogas production values and relative abundance of OPB54 and Bacteroidia after 20 d of SS-AD can be fitted well using a quadratic model, implying that OPB54 and Bacteroidia play important roles in the methanogenic metabolism for agricultural waste thermophilic SS-AD.

Effects of light intensity on biomass, carbohydrate and fatty acid compositions of three different mixed consortia from natural ecological water bodies.

This study investigated the effect of light intensity on three various microalga consortia collected from natural ecological water bodies (named A, B and C) towards their fatty acid profiling and fractions, carbohydrate and protein production at different light intensities of 100, 200 and 300 µmol m-2 s-1. The results indicating that increasing light intensity positively correlated with the lipid production than carbohydrate and protein. Irrespective to the solids (Total and Volatile Solid) content, lipids and carbohydrate has varied significantly. Consortia C showed higher productivity toward lipids, whereas consortia A and B accumulated more carbohydrate and protein, respectively. The microscopic images revealed the breakdown of cells during the increase in light intensity, in spite, the similar algal species were observed in all consortia experimented. Principal component analysis (PCA) revealed that low light intensity aid relatively in high protein, Total Nitrogen and Total Phosphorus, meanwhile high intensity attributed carbohydrates and unsaturated fatty acids (USFA) contents.

A comprehensive review on two-stage integrative schemes for the valorization of dark fermentative effluents.

This review provides the alternative routes towards the valorization of dark H2 fermentation effluents that are mainly rich in volatile fatty acids such as acetate and butyrate. Various enhancement and alternative routes such as photo fermentation, anaerobic digestion, utilization of microbial electrochemical systems, and algal system towards the generation of bioenergy and electricity and also for efficient organic matter utilization are highlighted. What is more, various integration schemes and two-stage fermentation for the possible scale up are reviewed. Moreover, recent progress for enhanced performance towards waste stabilization and overall utilization of useful and higher COD present in the organic source into value-added products are extensively discussed.

Comparison of alternative remediation technologies for recycled gravel contaminated with heavy metals.

To evaluate the effects of different remediation methods on heavy metals contaminated recycled gravel, three immobilization agents (monopotassium phosphate, lime, nano-iron) and two mobilization agents (glyphosate, humic acid (HA)) were studied and compared. Results indicated that nano-iron powder was found to be more effective to immobilize Zn, Cu, Pb and Cd. Meanwhile, glyphosate presents a higher mobilization effect than HA with removal rates of about 66.7% for Cd, more than 80% for Cr, Cu and Zn, and the highest removal percentage of 85.9% for Cr. After the mobilization by glyphosate, the leaching rates of Zn, Cu and Cr were about 0.8%, and below 0.2% for Pb and Cd. The leaching rates after nano-iron powder treatment were 1.18% for Zn, 0.96% for Cr, 0.61% for Cu, 0.45% for Pb and Cd not detected. The formation and disappearance of metal (Zn/Cu/Cr/Pb/Cd) compounds were firmly confirmed through X-ray diffraction and scanning electron microscopy analyses on crystalline phases and morphological surface structures.

Natural defence mechanisms of electrochemically active biofilms: From the perspective of microbial adaptation, survival strategies and antibiotic resistance.

Electrochemically active biofilms (EABs) play an ever-growingly critical role in the biological treatment of wastewater due to its low carbon footprint and sustainability. However, how the multispecies biofilms adapt, survive and become tolerant under acute and chronic toxicity such as antibiotic stress still remains well un-recognized. Here, the stress responses of EABs to tetracycline concentrations (CTC) and different operation schemes were comprehensively investigated. Results show that EABs can quickly adapt (start-up time is barely affected) to low CTC (≤ 5 µM) exposure while the adaptation time of EABs increases and the bioelectrocatalytic activity decreases at CTC ≥ 10 µM. EABs exhibit a good resilience and high anti-shocking capacity under chronic and acute TC stress, respectively. But chronic effects negatively affect the metabolic activity and extracellular electron transfer, and simultaneously change the spatial morphology and microbial community structure of EABs. Particularly, the typical exoelectrogens Geobacter anodireducens can be selectively enriched under chronic TC stress with relative abundance increasing from 45.11% to 85.96%, showing stronger TC tolerance than methanogens. This may be attributed to the effective survival strategies of EABs in response to TC stress, including antibiotic efflux regulated by tet(C) at the molecular level and the secretion of more extracellular proteins in the macro scale, as the C=O bond in amide I of aromatic amino acids plays a critical role in alleviating the damage of TC to cells. Overall, this study highlights the versatile defences of EABs in terms of microbial adaptation, survival strategies, and antibiotic resistance, and deepens the understanding of microbial communities' evolution of EABs in response to acute and chronic TC stress.

Sludge bound-EPS solubilization enhance CH4 bioconversion and membrane fouling mitigation in electrochemical anaerobic membrane bioreactor: Insights from continuous operation and interpretable machine learning algorithms.

Bound extracellular polymeric substances (EPS) are complex, high-molecular-weight polymer mixtures that play a critical role in pore clogging, foulants adhesion, and fouling layer formation during membrane filtration, owing to their adhesive properties and gelation tendencies. In this study, a novel electrochemical anaerobic membrane bioreactor (EC-AnMBR) was constructed to investigate the effect of sludge bound-EPS solubilization on methane bioconversion and membrane fouling mitigation. During the 150-days' operation, the EC-AnMBR demonstrated remarkable performance, characterized by an exceptionally low fouling rate (transmembrane pressure (TMP) < 4.0 kPa) and high-quality effluent (COD removal > 98.2 %, protein removal > 97.7 %, and polysaccharide removal > 98.5 %). The highest methane productivity was up to 38.0 ± 3.1 mL/Lreactor/d at the applied voltage of 0.8 V with bound-EPS solubilization, 107.6 % higher than that of the control stage (18.3 ± 2.4 mL/Lreactor/d). Morphological and multiplex fluorescence labeling analyses revealed higher fluorescence intensities of proteins, polysaccharides, total cells and lipids on the surface of the fouling layer. In contrast, the interior exhibited increased compression density and reduced activity, likely attributable to compression effect. Under the synergistic influence of the electric field and bound-EPS solubilization, biomass characteristics exhibited a reduced propensity for membrane fouling. Furthermore, the bio-electrochemical regulation enhanced the electroactivity of microbial aggregates and enriched functional microorganisms, thereby promoting biofilm growth and direct interspecies electron transfer. Additionally, the potential hydrogenotrophic and methylotrophic methanogenesis pathways were enhanced at the cathode and anode surfaces, thereby increasing CH4 productivity. The random forest-based machine learning model analyzed the nonlinear contributions of EPS characteristics on methane productivity and TMP values, achieving R² values of 0.879 and 0.848, respectively. Shapley additive explanations (SHAP) analysis indicated that S-EPSPS and S-EPSPN were the most critical factors affecting CH4 productivity and membrane fouling, respectively. Partial dependence plot analysis further verified the marginal and interaction effects of different EPS layers on these outcomes. By combining continuous operation with interpretable machine learning algorithms, this study unveils the intricate impacts of EPS characteristics on methane productivity and membrane fouling behaviors, and provides new insights into sludge bound-EPS solubilization in EC-AnMBR.

Identification of extracellular polymeric substances layer barrier in chloroquine phosphate-disturbed anammox consortia and mechanism dissection on cytotoxic behavior by computational chemistry.

The over-dosing use of chloroquine phosphate (CQ) poses severe threats to human beings and ecosystem due to the high persistence and biotoxicity. The discharge of CQ into wastewater would affect the biomass activity and process stability during the biological processes, e.g., anammox. However, the response mechanism of anammox consortia to CQ remain unknown. In this study, the accurate role of extracellular polymeric substances barrier in attenuating the negative effects of CQ, and the mechanism on cytotoxic behavior were dissected by molecular spectroscopy and computational chemistry. Low concentrations (≤6.0 mg/L) of CQ hardly affected the nitrogen removal performance due to the adaptive evolution of EPS barrier and anammox bacteria. Compact protein of EPS barrier can bind more CQ (0.24 mg) by hydrogen bond and van der Waals force, among which O-H and amide II region respond CQ binding preferentially. Importantly, EPS contributes to the microbiota reshape with selectively enriching Candidatus_Kuenenia for self-protection. Furthermore, the macroscopical cytotoxic behavior was dissected at a molecular level by CQ fate/distribution and computational chemistry, suggesting that the toxicity was ascribed to attack of CQ on functional proteins of anammox bacteria with atom N17 (f-=0.1209) and C2 (f+=0.1034) as the most active electrophilic and nucleophilic sites. This work would shed the light on the fate and risk of non-antibiotics in anammox process.

Hydrogen production promotion and energy saving in anaerobic co-fermentation of heat-treated sludge and food waste.

The objective of this paper is to gain insights into the synergistic advantage of anaerobic co-fermentation of heat-treated sludge (HS) with food waste (FW) and heat-treated food waste (HFW) for hydrogen production. The results showed that, compared with raw sludge (RS) mixed with FW (RS-FW), the co-substrate of HS mixed with either FW (HS-FW) or HFW (HS-HFW) effectively promoted hydrogen production, with HS-HFW promoted more than HS-FW. The maximum specific hydrogen production (MSHP) and the maximum hydrogen concentration (MHC) of HS-HFW were 40.53 mL H2/g dry weight and 57.22%, respectively, and 1.21- and 1.45-fold as high as those from HS-FW. The corresponding fermentation was ethanol type for HS-HFW and butyric acid type for HS-FW. The net energy production from RS-FW and HS-FW was both negative, but it was positive (2.57 MJ) from 40% HFW addition to HS-HFW. Anaerobic fermentation was more viable for HS-HFW.

Optimizing bioelectromethanosynthesis of CO2 and membrane fouling mitigation in MECs via in-situ biogas recirculation.

The CO2 bioelectromethanosynthesis via two-chamber microbial electrolysis cell (MEC) holds tremendous potential to solve the energy crisis and mitigate the greenhouse gas emissions. However, the membrane fouling is still a big challenge for CO2 bioelectromethanosynthesis owing to the poor proton diffusion across membrane and high inter-resistance. In this study, a new MEC bioreactor with biogas recirculation unit was designed in the cathode chamber to enhance secondary-dissolution of CO2 while mitigating the contaminant adhesion on membrane surface. Biogas recirculation improved CO2 re-dissolution, reduced concentration polarization, and facilitated the proton transmembrane diffusion. This resulted in a remarkable increase in the cathodic methane production rate from 0.4 mL/L·d to 8.5 mL/L·d. A robust syntrophic relationship between anodic organic-degrading bacteria (Firmicutes 5.29%, Bacteroidetes 25.90%, and Proteobacteria 6.08%) and cathodic methane-producing archaea (Methanobacterium 65.58%) enabled simultaneous organic degradation, high CO2 bioelectromethanosynthesis, and renewable energy storage.

Biogas upgrading and membrane anti-fouling mechanisms in electrochemical anaerobic membrane bioreactor (EC-AnMBR): Focusing on spatio-temporal distribution of metabolic functionality of microorganisms.

Electrochemical anaerobic membrane bioreactor (EC-AnMBR) by integrating a composite anodic membrane (CAM), represents an effective method for promoting methanogenic performance and mitigating membrane fouling. However, the development and formation of electroactive biofilm on CAM, and the spatio-temporal distribution of key functional microorganisms, especially the degradation mechanism of organic pollutants in metabolic pathways were not well documented. In this work, two AnMBR systems (EC-AnMBR and traditional AnMBR) were constructed and operated to identify the role of CAM in metabolic pathway on biogas upgrading and mitigation of membrane fouling. The methane yield of EC-AnMBR at HRT of 20 days was 217.1 ± 25.6 mL-CH4/g COD, about 32.1 % higher compared to the traditional AnMBR. The 16S rRNA analysis revealed that the EC-AnMBR significantly promoted the growth of hydrolysis bacteria (Lactobacillus and SJA-15) and methanogenic archaea (Methanosaeta and Methanobacterium). Metagenomic analysis revealed that the EC-AnMBR promotes the upregulation of functional genes involved in carbohydrate metabolism (gap and kor) and methane metabolism (mtr, mcr, and hdr), improving the degradation of soluble microbial products (SMPs)/extracellular polymeric substances (EPS) on the CAM and enhancing the methanogens activity on the cathode. Moreover, CAM biofilm exhibits heterogeneity in the degradation of organic pollutants along its vertical depth. The bacteria with high hydrolyzing ability accumulated in the upper part, driving the feedstock degradation for higher starch, sucrose and galactose metabolism. A three-dimensional mesh-like cake structure with larger pores was formed as a biofilter in the middle and lower part of CAM, where the electroactive Geobacter sulfurreducens had high capabilities to directly store and transfer electrons for the degradation of organic pollutants. This outcome will further contribute to the comprehension of the metabolic mechanisms of CAM module on membrane fouling control and organic solid waste treatment and disposal.

Enhanced dewaterability and triclosan removal of waste activated sludge with iron-rich mineral-activated peroxymonosulfate.

High water and pharmaceutical and care products (PPCPs) bounded in sludge flocs limit its utilization and disposal. The advanced oxidation process of perxymonosulfate (PMS) catalyzed by iron salts has been widely used in sludge conditioning. In this study, two iron-rich minerals pyrite and siderite were proposed to enhance sludge dewatering performance and remove the target contaminant of triclosan (TCS). The permanent release of Fe2+ in the activation of PMS made siderite more effective in enhancing sludge dewater with capillary suction time (CST) diminishing by 60.5 %, specific resistance to filtration (SRF) decreasing by 79.2 %, and bound water content (BWC) dropping from 37.1 % to 2.6 % at siderite/PMS dosages of 0.36/0.20 mmol/g-TSS after 20 min of pretreatment. Pyrite/PMS performed slightly inferior under the same conditions and the corresponding CST and SRF decreased by 51.5 % and 71.8 % while the BWC only declined to 17.8 %. Rheological characterization was employed to elucidate the changes in sludge dewatering performance, with siderite/PMS treated sludge showing a 48.3 % reduction in thixotropy, higher than 28.4 % of pyrite/PMS. Oscillation and creep tests further demonstrated the significantly weakened viscoelastic behavior of the sludge by siderite/PMS pretreatment. For TCS mineralization removal, siderite/PMS achieved a high removal efficiency of 43.9 %, in comparison with 39.9 % for pyrite/PMS. The reduction in the sludge solids phase contributed the most to the TCS removal. Free radical quenching assays and EPR spectroscopy showed that both siderite/PMS and pyrite/PMS produced SO4-·  and ·OH, with the latter acting as the major radicals. Besides, the dosage of free radicals generated from siderite/PMS exhibited a lower time-dependence, which also allowed it to outperform in destroying EPS matrix, neutralizing the negative Zeta potential of sludge flocs, and mineralizing macromolecular organic matter.

Simultaneous removal of antibiotic resistance genes and improved dewatering ability of waste activated sludge by Fe(II)-activated persulfate oxidation.

Waste activated sludge properties vary widely with different regions due to the difference in living standards and geographical distribution, making a big challenge to developing a universally effective sludge dewatering technique. The Fe(II)-activated persulfate (S2O82-) oxidation process shows excellent ability to disrupt sludge cells and extracellular polymeric substances (EPS), and release bound water from sludge flocs. In this study, the discrepancies in the physicochemical characteristics of sludge samples from seven representative cities in China (e.g., dewaterability, EPS composition, surface charge, microbial community, relative abundance of antibiotic resistance genes (ARGs), etc.) were investigated, and the role of Fe(II)-S2O82- oxidation in enhancing removal of antibiotic resistance genes and dewatering ability were explored. The results showed significant differences between the EPS distribution and chemical composition of sludge samples due to different treatment processes, effluent sources, and regions. The Fe(II)-S2O82- oxidation pretreatment had a good enhancement of sludge dewatering capacity (up to 76 %). Microbial analysis showed that the microbial community in each sludge varied significantly depending on the types of wastewater, the wastewater treatment processes, and the regions, but Fe(II)-S2O82- oxidation was able to attack and rupture the sludge zoogloea indiscriminately. Genetic analysis further showed that a considerable number of ARGs were detected in all of these sludge samples and that Fe(II)-S2O82- oxidation was effective in removing ARGs by higher than 90 %. The highly active radicals (e.g., SO4-·, ·OH) produced in this process caused drastic damage to sludge microbial cells and DNA stability while liberating the EPS/cell-bound water. Co-occurrence network analysis highlighted a positive correlation between population distribution and ARGs abundance, while variations in microbial communities were linked to regional differences in living standards and level of economic development. Despite these variations, the Fe(II)-S2O82- oxidation consistently achieved excellent performance in both ARGs removal and sludge dewatering. The significant modularity of associations between different microbial communities also confirms its ability to reduce horizontal gene transfer (HGT) by scavenging microbes.

Bioelectrochemically altering microbial ecology in upflow anaerobic sludge blanket to enhance methanogenesis fed with high-sulfate methanolic wastewater.

A bioelectrochemical upflow anaerobic sludge blanket (BE-UASB) was constructed and compared with the traditional UASB to investigate the role of bioelectrocatalysis in modulating methanogenesis and sulfidogensis involved within anaerobic treatment of high-sulfate methanolic wastewater (COD/SO42- ratio ≤ 2). Methane production rate for BE-UASB was 1.4 times higher than that of the single UASB, while SO42- removal stabilized at 16.7%. Bioelectrocatalysis selectively enriched key functional anaerobes and stimulated the secretion of extracellular polymeric substances, especially humic acids favoring electron transfer, thereby accelerating the electroactive biofilms development of electrodes. Methanomethylovorans was the dominant genus (35%) to directly convert methanol to CH4. Methanobacterium as CO2 electroreduction methane-producing archaea appeared only on electrodes. Acetobacterium exhibited anode-dependence, which provided acetate for sulfate-reducing bacteria (norank Syntrophobacteraceae and Desulfomicrobium) through synergistic coexistence. This study confirmed that BE-UASB regulated the microbial ecology to achieve efficient removal and energy recovery of high-sulfate methanolic wastewater.

Characterization of controlled low-strength material obtained from dewatered sludge and refuse incineration bottom ash: mechanical and microstructural perspectives.

Potential reuse of dewatered sludge (DS) and municipal solid waste incineration (MSWI) bottom ash as components to develop controlled low-strength material (CLSM) was explored. The effects of DS:MSWI bottom ash:calcium sulfoaluminate (CS¯A) cement ratio and thermal treatment of MSWI bottom ash at 900 °C on the mechanical and microstructural properties of CLSM were intensively studied to optimize the process. Results showed DS and MSWI bottom ash could be utilized for making CLSM. The CLSM prepared with milled MSWI bottom ash gave higher unconfined compressive strength (UCS) of 2.0-6.2 MPa following 1 year of curing at 1.0:0.1:0.9 ≤ DS:MSWI bottom ash:CS¯A ≤ 1.0:0.8:0.2. However, the corresponding strengths for CLSM containing thermally treated MSWI bottom ash ranged from 0.7 to 4.6 MPa, decreasing 26-65%. The microstructural analysis by X-ray powder diffraction (XRD), Fourier transforms infrared spectroscopy (FT-IR), as well as scanning electron microscopy (SEM) combined with an energy dispersive X-ray spectroscopy (EDS) revealed that ettringite (C3A·3CS¯·H32, or AFt) crystals were the most important strength-producing constituents which grew into and filled the CLSM matrix pores. Milled MSWI bottom ash addition favored the formation of highly crystalline AFt phases and accordingly enhanced compressive strengths of CLSM specimens. In contrast, thermal treatment at 900 °C produced new phases such as gehlenite (Ca2Al2SiO7) and hydroxylapatite (Ca5(PO4)3(OH)), which deteriorated the pozzolanic activity of bottom ash and caused the strengths to decrease. Leaching tests evidenced that leachable substances from CLSM samples exhibited negligible health and environmental risks. The results of this study suggested that MSWI bottom ash can be effectively recycled together with DS in developing CLSM mixtures with restricted use of CS¯A cement.

Self-assembled electrochemically active biofilms doped with carbon nanotubes: Electron exchange efficiency and cytotoxicity evaluation.

Thick electrochemically active biofilms (EABs) will lead to insufficient extracellular electron transfer (EET) rate because of the limitation of both substrate diffusion and electron exchange. Herein, carbon nanotubes (CNTs)-doped EABs are developed through self-assembly. The highly conductive biofilms (internal resistance of ∼211 Ω) are efficiently enriched at CNTs dosage of 1 g L-1, with the stable power output of 0.568 W m-2 over three months. The embedded CNTs can act as electron tunnel to accelerate the EET rate in thick biofilm. Self-charging/discharging experiments and Nernst-Monod model stimulation demonstrate a higher net charge storage capacity (0.15 C m-2) and more negative half-saturation potential (-0.401 V) for the hybrid biofilms than that of the control (0.09 C m-2, and -0.378 V). Enzyme activity tests and the observation of confocal laser scanning microscopy by live/dead staining show a nearly negligible cytotoxicity of CNTs, and non-targeted metabonomics analysis reveals fourteen differential metabolites that do not play key roles in microbial central metabolic pathways according to KEGG compound database. The abundance of typical exoelectrogens Geobacter sp. is 2-fold of the control, resulting in a better bioelectrocatalytic activity. These finding provide a possible approach to prolong electron exchange and power output by developing a hybrid EABs doped with conductive material.

Long-term performance, microbial evolution and spatial microstructural characteristics of anammox granules in an upflow blanket filter (UBF) treating high-strength nitrogen wastewater.

Granule formation, microstructure and microbial spatial distribution are crucial to granule stability and nitrogen removal. Here, an upflow blanket filter (UBF) reactor with porous fixed cylinder carriers was fabricated and operated for 234 days to investigate overall performance and the formation mechanism of anammox granules. Results showed that the UBF performed the highest nitrogen removal efficiency of 93.19 ± 3.39% under nitrogen loading rate of 3.6 kg-N/m3/d and HRT of 2 h. The tryptophan-like proteins as the key component in EPS were vital for granules formation. Further 16 s rRNA analysis indicated that SBR1031 with a relative abundance of 40.5% played an important role in cell aggregation. Thus, anammox granules were developed successfully with a two-layered spatial structure where outer-layer was ammonia oxidizing bacteria and inner-core was anaerobic ammonia oxidizing bacteria. Together, introduction of porous fixed cylinder carriers is a valid method to avoid biomass loss and floatation.

Prospects for humic acids treatment and recovery in wastewater: A review.

Clean water shortages require the reuse of wastewater. The presence of organic substances such as humic acids in wastewater makes the water treatment process more difficult. Humic acids can significantly affect the removal of heavy metals and other such toxins. Humic acids is formed by the decomposition and transformation of animal and plant remains by microorganisms, and naturally exists in soil and water. It is necessary to degrade and remove humic acids from wastewater. As it seriously human health, effective technologies for removing humic acids from wastewater have attracted great interest over the past decades. This study compared existing techniques for removing humic acids from wastewater, as well as their limitations. Physicochemical treatments including filtration and oxidation are basic and key approaches to removing humic acids. Biological treatments including enzyme and fungi-mediated humic acids degradation are economically feasible but require some scalability. In conclusion, the integrated treatment processes are more significant options for the effective removal of humic acids from wastewater. In addition, humic acids have rich utilization values. It can improve the soil, increase crop yields, and promote the removal of pollutants.

Effective multipurpose sewage sludge and food waste reduction strategies: A focus on recent advances and future perspectives.

Energy crisis and increasing rigorous management standards pose significant challenges for solid waste management worldwide. Several emerging diseases such as COVID-19 aggravated the already complex solid waste management crisis, especially sewage sludge and food waste streams, because of the increasingly large production year by year. As mature waste disposal technologies, landfills, incineration, composting, and some other methods are widespread for solid wastes management. This paper reviews recent advances in key sewage sludge disposal technologies. These include incineration, anaerobic digestion, and valuable products oriented-conversion. Food waste disposal technologies comprised of thermal treatment, fermentation, value-added product conversion, and composting have also been described. The hot topic and dominant research foci of each area are summarized, simultaneously compared with conventional technologies in terms of organic matter degradation or conversion performance, energy generation, and renewable resources production. Future perspectives of each technology that include issues not well understood and predicted challenges are discussed with a positive effect on the full-scale implementation of the discussed disposal methods.

Impact of sandwich-type composite anodic membrane on membrane fouling and methane recovery from sewage sludge and food waste via electrochemical anaerobic membrane bioreactor.

Membrane fouling presents a big challenge for the real-world implementation of anaerobic membrane bioreactors (AnMBRs) in digesting high-solid biowastes. In this study, an electrochemical anaerobic membrane bioreactor (EC-AnMBR) with a novel sandwich-type composite anodic membrane was designed and constructed for controlling membrane fouling whilst improving the energy recovery. The results showed that EC-AnMBR produced a higher methane yield of 358.5 ± 74.8 mL/d, rising by 12.8% compared to the AnMBR without applied voltage. Integration of composite anodic membrane induced a stable membrane flux and low transmembrane pressure through forming an anodic biofilm while total coliforms removal reached 97.9%. The microbial community analysis further provided compelling evidence that EC-AnMBR enriched the relative abundance of hydrolyzing (Chryseobacterium 2.6%) bacteria and methane-producing (Methanobacterium 32.8%) archaea. These findings offered new insights into anti-biofouling performance and provided significant implications for municipal organic waste treatment and energy recovery in the new EC-AnMBR.