Unlocking the Na-Storage Behavior in Hard Carbon Anode by Mass Spectrometry.

Hard carbon (HC) is a promising anode candidate for Na-ion batteries (NIBs) because of its excellent Na-storage performance, abundance, and low cost. However, a precise understanding of its Na-storage behavior remains elusive. Herein, based on the D2O/H2SO4-based TMS results collected on charged/discharged state HC electrodes, detailed Na-storage mechanisms (the Na-storage states and active sites in different voltage regions), specific SEI dynamic evolution process (formation, rupture, regeneration and loss), and irreversible capacity contribution (dead Na0, NaH, etc.) were elucidated. Moreover, by employing the online electrochemical mass spectrometry (OEMS) to monitor the gassing behavior of HC-Na half-cell during the overdischarging process, a surprising rehydrogen evolution reaction (re-HER) process at around 0.02 V vs Na+/Na was identified, indicating the occurrence of Na-plating above 0 V vs Na+/Na. Additionally, the typical fluorine ethylene carbonate (FEC) additive was demonstrated to reduce the accumulation of dead Na0 and inhibit the re-HER process triggered by plated Na.

Spatial Effect on the Performance of Carboxylate Anode Materials in Na-Ion Batteries.

Developing low-voltage carboxylate anode materials is critical for achieving low-cost, high-performance, and sustainable Na-ion batteries (NIBs). However, the structure design rationale and structure-performance correlation for organic carboxylates in NIBs remains elusive. Herein, the spatial effect on the performance of carboxylate anode materials is studied by introducing heteroatoms in the conjugation structure and manipulating the positions of carboxylate groups in the aromatic rings. Planar and twisted organic carboxylates are designed and synthesized to gain insight into the impact of geometric structures to the electrochemical performance of carboxylate anodes in NIBs. Among the carboxylates, disodium 2,2'-bipyridine-5,5'-dicarboxylate (2255-Na) with a planar structure outperforms the others in terms of highest specific capacity (210 mAh g-1), longest cycle life (2000 cycles), and best rate capability (up to 5 A g-1). The cyclic stability and redox mechanism of 2255-Na in NIBs are exploited by various characterization techniques. Moreover, high-temperature (up to 100 °C) and all-organic batteries based on a 2255-Na anode, a polyaniline (PANI) cathode, and an ether-based electrolyte are achieved and exhibited exceptional electrochemical performance. Therefore, this work demonstrates that designing organic carboxylates with extended planar conjugation structures is an effective strategy to achieve high-performance and sustainable NIBs.

Revealing the Role of Ruthenium on the Performance of P2-Type Na0.67Mn1-xRuxO2 Cathodes for Na-Ion Full-Cells.

Herein, P2-type layered manganese and ruthenium oxide is synthesized as an outstanding intercalation cathode material for high-energy density Na-ion batteries (NIBs). P2-type sodium deficient transition metal oxide structure, Na0.67Mn1-xRuxO2 cathodes where x varied between 0.05 and 0.5 are fabricated. The partially substituted main phase where x = 0.4 exhibits the best electrochemical performance with a discharge capacity of ≈170 mAh g-1. The in situ X-ray Absorption Spectroscopy (XAS) and time-resolved X-ray Diffraction (TR-XRD) measurements are performed to elucidate the neighborhood of the local structure and lattice parameters during cycling. X-ray photoelectron spectroscopy (XPS) revealed the oxygen-rich structure when Ru is introduced. Density of States (DOS) calculations revealed the Fermi-Level bandgap increases when Ru is doped, which enhances the electronic conductivity of the cathode. Furthermore, magnetization calculations revealed the presence of stronger Ru─O bonds and the stabilizing effect of Ru-doping on MnO6 octahedra. The results of Time-of-flight secondary-ion mass spectroscopy (TOF-SIMS) revealed that the Ru-doped sample has more sodium and oxygenated-based species on the surface, while the inner layers mainly contain Ru-O and Mn-O species. The full cell study demonstrated the outstanding capacity retention where the cell maintained 70% of its initial capacity at 1 C-rate after 500 cycles.

Molecular Engineering to Regulate the Pseudo-Graphitic Structure of Hard Carbon for Superior Sodium Energy Storage.

Resin-derived hard carbons have shown great advantages in serving as promising anode materials for sodium-ion batteries due to their flexible microstructure tunability. However, it remains a daunting challenge to rationally regulate the pseudo-graphitic crystallite and defect of hard carbon toward advanced sodium storage performance. Herein, a molecular engineering strategy is demonstrated to modulate the cross-linking degree of phenolic resin and thus optimize the microstructure of hard carbon. Remarkably, the resorcinol endows resin with a moderate cross-linking degree, which can finely tune the pseudo-graphitic structure with enlarged interlayer spacing and restricted surface defects. As a consequence, the optimal hard carbon delivers a notable reversible capacity of 334.3 mAh g-1 at 0.02 A g-1, a high initial Coulombic efficiency of 82.1%, superior rate performance of 103.7 mAh g-1 at 2 A g-1, and excellent cycling durability over 5000 cycles. Furthermore, kinetic analysis and in situ Raman spectroscopy are performed to reveal the electrochemical advantage and sodium storage mechanism. This study fundamentally sheds light on the molecular design of resin-based hard carbons to advance sodium energy for scale-up applications.

Dual-Site Doping in Transition Metal Oxide Cathode Enables High-Voltage Stability of Na-Ion Batteries.

Designing cathode materials that effectively enhancing structural stability under high voltage is paramount for rationally enhancing energy density and safety of Na-ion batteries. This study introduces a novel P2-Na0.73K0.03Ni0.23Li0.1Mn0.67O2 (KLi-NaNMO) cathode through dual-site synergistic doping of K and Li in Na and transition metal (TM) layers. Combining theoretical and experimental studies, this study discovers that Li doping significantly strengthens the orbital overlap of Ni (3d) and O (2p) near the Fermi level, thereby regulates the phase transition and charge compensation processes with synchronized Ni and O redox. The introduction of K further adjusts the ratio of Nae and Naf sites at Na layer with enhanced structural stability and extended lattice space distance, enabling the suppression of TM dissolution, achieving a single-phase transition reaction even at a high voltage of 4.4 V, and improving reaction kinetics. Consequently, KLi-NaNMO exhibits a high capacity (105 and 120 mAh g-1 in the voltage of 2-4.2 V and 2-4.4 V at 0.1 C, respectively) and outstanding cycling performance over 300 cycles under 4.2 and 4.4 V. This work provides a dual-site doping strategy to employ synchronized TM and O redox with improved capacity and high structural stability via electronic and crystal structure modulation.

Fabrication of a Stable and Highly Effective Anode Material for Li-Ion/Na-Ion Batteries Utilizing ZIF-12.

Transition metal selenides (TMSs) are receiving considerable interest as improved anode materials for sodium-ion batteries (SIBs) and lithium-ion batteries (LIBs) due to their considerable theoretical capacity and excellent redox reversibility. Herein, ZIF-12 (zeolitic imidazolate framework) structure is used for the synthesis of Cu2Se/Co3Se4@NPC anode material by pyrolysis of ZIF-12/Se mixture. When Cu2Se/Co3Se4@NPC composite is utilized as an anode electrode material in LIB and SIB half cells, the material demonstrates excellent electrochemical performance and remarkable cycle stability with retaining high capacities. In LIB and SIB half cells, the Cu2Se/Co3Se4@NPC anode material shows the ultralong lifespan at 2000 mAg-1, retaining a capacity of 543 mAhg-1 after 750 cycles, and retaining a capacity of 251 mAhg-1 after 200 cycles at 100 mAg-1, respectively. The porous structure of the Cu2Se/Co3Se4@NPC anode material can not only effectively tolerate the volume expansion of the electrode during discharging and charging, but also facilitate the penetration of electrolyte and efficiently prevents the clustering of active particles. In situ X-ray difraction (XRD) analysis results reveal the high potential of Cu2Se/Co3Se4@NPC composite in building efficient LIBs and SIBs due to reversible conversion reactions of Cu2Se/Co3Se4@NPC for lithium-ion and sodium-ion storage.

Lithium Azides Induced SnS Quantum Dots for Ultra-Fast and Long-Term Sodium Storage.

Tin sulfide (SnS) is an attractive anode for sodium ion batteries (NIBs) because of its high theoretical capacity, while it seriously suffers from the inherently poor conductivity and huge volume variation during the cycling process, leading to inferior lifespan. To intrinsically maximize the sodium storage of SnS, herein, lithium azides (LiN3 )-induced SnS quantum dots (QDs) are first reported using a simple electrospinning strategy, where SnS QDs are uniformly distributed in the carbon fibers. Taking the advantage of LiN3 , which can effectively prevent the growth of crystal nuclei during the thermal treatment, the well-dispersed SnS QDs performs superior Na+ transfer kinetics and pseudocapacitive when used as an anode material for NIBs. The 3D SnS quantum dots embedded uniformly in N-doped nanofibers (SnS QDs@NCF) electrodes display superior long cycling life-span (484.6 mAh g-1 after 5800 cycles at 2 A g-1 and 430.9 mAh g-1 after 7880 cycles at 10 A g-1 ), as well as excellent rate capability (422.3 mAh g-1 at 20 A g-1 ). This fabrication of transition metal sulfides QDs composites provide a feasible strategy to develop NIBs with long life-span and superior rate capability to pave its practical implementation.

From Li to Na: Exploratory Analysis of Fe-Based Phosphates Polyanion-Type Cathode Materials by Mn Substitution.

Both LiFePO4 (LFP) and NaFePO4 (NFP) are phosphate polyanion-type cathode materials, which have received much attention due to their low cost and high theoretical capacity. Substitution of manganese (Mn) elements for LFP/NFP materials can improve the electrochemical properties, but the connection between local structural changes and electrochemical behaviors after Mn substitution is still not clear. This study not only achieves improvements in energy density of LFP and cyclic stability of NFP through Mn substitution, but also provides an in-depth analysis of the structural evolutions induced by the substitution. Among them, the substitution of Mn enables LiFe0.5 Mn0.5 PO4 to achieve a high energy density of 535.3 Wh kg-1 , while NaFe0.7 Mn0.3 PO4 exhibits outstanding cyclability with 89.6% capacity retention after 250 cycles. Specifically, Mn substitution broadens the ion-transport channels, improving the ion diffusion coefficient. Moreover, LiFe0.5 Mn0.5 PO4 maintains a more stable single-phase transition during the charge/discharge process. The transition of NaFe0.7 Mn0.3 PO4 to the amorphous phase is avoided, which can maintain structural stability and achieve better electrochemical performance. With systematic analysis, this research provides valuable guidance for the subsequent design of high-performance polyanion-type cathodes.

Rational Engineering of p-n Heterogeneous ZnS/SnO2 Quantum Dots with Fast Ion Kinetics for Superior Li/Na-Ion Battery.

Constructing heterogeneous nanostructures is an efficient strategy to improve the electrical and ionic conductivity of metal chalcogenide-based anodes. Herein, ZnS/SnO2 quantum dots (QDs) as p-n heterojunctions that are uniformly anchored to reduced graphene oxides (ZnS-SnO2 @rGO) are designed and engineered. Combining the merits of fast electron transport via the internal electric field and a greatly shortened Li/Na ion diffusion pathway in the ZnS/SnO2 QDs (3-5 nm), along with the excellent electrical conductivity and good structural stability provided by the rGO matrix, the ZnS-SnO2 @rGO anode exhibits enhanced electronic and ionic conductivity, which can be proved by both experiments and theoretical calculations. Consequently, the ZnS-SnO2 @rGO anode shows a significantly improved rate performance that simple counterpart composite anodes cannot achieve. Specifically, high reversible specific capacities are achieved for both lithium-ion battery (551 mA h g-1 at 5.0 A g-1 , 670 mA h g-1 at 3.0 A g-1 after 1400 cycles) and sodium-ion battery (334 mA h g-1 at 5.0 A g-1 , 313 mA h g-1 at 1.0 A g-1 after 400 cycles). Thus, this strategy to build semiconductor metal sulfides/metal oxide heterostructures at the atomic scale may inspire the rational design of metal compounds for high-performance battery applications.

Is "Water in Salt" Electrolytes the Ultimate Solution? Achieving High Stability of Organic Anodes in Diluted Electrolyte Solutions Via a Wise Anions Selection.

The introduction of the water-in-salt (WIS) electrolytes concept to prevent water splitting and widen the electrochemical stability window, has spurred extensive research efforts toward development of improved aqueous batteries. The successful implementation of these electrolyte solutions in many electrochemical systems shifts the focus from diluted to WIS electrolyte solutions. Considering the high costs and the tendency of these nearly saturated solutions to crystallize, this trend can be carefully re-evaluated. Herein we show that the stability of organic electrodes comprising the active material perylene-3,4,9,10-tetracarboxylic dianhydride (PTCDA), is strongly influenced by the solvation character of the anions rather than the concentration of the electrolyte solution. Even though the charging process of PTCDA involves solely insertion of cations (i.e., principal counter-ions), surprisingly, the dominant factor influencing its electrochemical performance, including long-term electrode stability, is the type of the co-ions (i.e., electrolytic anions). Using systematic electrochemical analysis combined with theoretical simulations, we show that the selection of kosmotropic anions results in fast fading of the PTCDA anodes, while a selection of chaotropic anions leads to excellent stability, even at electrolytes concentrations as low as 0.2 M. These findings provide a new conceptual approach for designing advanced electrolyte solutions for aqueous batteries.