Dopamine-induced photoluminescence quenching of bovine serum albumin-capped manganese-doped zinc sulphide quantum dots.

The direct detection of dopamine (DA) in human body fluids is a great challenge for medical diagnostics of neurological disorders like Parkinson's disease, Alzheimer's disease, senile dementia, and schizophrenia. In this work, a simple and turn off luminescence sensing of DA based on bovine serum albumin (BSA)-capped manganese-doped zinc sulphide quantum dots (Mn:ZnS/BSA QDs) is developed. The Mn:ZnS/BSA QDs were synthesized by a chemical co-precipitation method. Due to the special interaction of DA with BSA and metal ions, Mn:ZnS/BSA QDs can serve as an effective sensing platform for DA. The luminescence of Mn:ZnS/BSA QDs decreased linearly with increasing concentration of DA in the range from 6.6 to 50.6 nM. The limit of detection is 2.02 nM. The driving force for the luminescence quenching is partly provided by ground-state complex formation of QDs with DA. The photo-induced electron transfer from the conduction band of QDs to oxidized dopamine (quinone) also favors quenching. The Mn:ZnS/BSA QDs are barely interfered with by other competing biomolecules except catecholamine neurotransmitter like epinephrine. Moreover, this method is used in the analysis of DA-spiked human serum and human urine samples and good recovery percentages are found. To assess the utility of the developed sensor, paper strip assay was also successfully conducted. Graphical abstract.

A microfluidic direct formate fuel cell on paper.

We describe the first direct formate fuel cell on a paper microfluidic platform. In traditional membrane-less microfluidic fuel cells (MFCs), external pumping consumes power produced by the fuel cell in order to maintain co-laminar flow of the anode stream and oxidant stream to prevent mixing. However, in paper microfluidics, capillary action drives flow while minimizing stream mixing. In this work, we demonstrate a paper MFC that uses formate and hydrogen peroxide as the anode fuel and cathode oxidant, respectively. Using these materials we achieve a maximum power density of nearly 2.5 mW/mg Pd. In a series configuration, our MFC achieves an open circuit voltage just over 1 V, and in a parallel configuration, short circuit of 20 mA absolute current. We also demonstrate that the MFC does not require continuous flow of fuel and oxidant to produce power. We found that we can pre-saturate the materials on the paper, stop the electrolyte flow, and still produce approximately 0.5 V for 15 min. This type of paper MFC has potential applications in point-of-care diagnostic devices and other electrochemical sensors.

A Paper-Based Biological Solar Cell.

A merged system incorporating paperfluidics and papertronics has recently emerged as a simple, single-use, low-cost paradigm for disposable point-of-care (POC) diagnostic applications. Stand-alone and self-sustained paper-based systems are essential to providing effective and lifesaving treatments in resource-constrained environments. Therefore, a realistic and accessible power source is required for actual paper-based POC systems as their diagnostic performance and portability rely significantly on power availability. Among many paper-based batteries and energy storage devices, paper-based microbial fuel cells have attracted much attention because bacteria can harvest electricity from any type of organic matter that is readily available in those challenging regions. However, the promise of this technology has not been translated into practical power applications because of its short power duration, which is not enough to fully operate those systems for a relatively long period. In this work, we for the first time demonstrate a simple and long-lasting paper-based biological solar cell that uses photosynthetic bacteria as biocatalysts. The bacterial photosynthesis and respiration continuously and self-sustainably generate power by converting light energy into electricity. With a highly porous and conductive anode and an innovative solid-state cathode, the biological solar cell built upon the paper substrates generated the maximum current and power density of 65 µA/cm2 and 10.7 µW/cm2, respectively, which are considerably greater than those of conventional micro-sized biological solar cells. Furthermore, photosynthetic bacteria in a 3-D volumetric chamber made of a stack of papers provided stable and long-lasting electricity for more than 5 h, while electrical current from the heterotrophic culture on 2-D paper dramatically decreased within several minutes.

Current status of point-of-care diagnostic devices in the Indian healthcare system with an update on COVID-19 pandemic.

Point-of-care (POC) diagnostic device is an instrument that is used to acquire particular clinical information of patients in clinical as well as resource-limited settings. The conventional clinical diagnostic procedure requires high-end and costly instruments, an expert technician for operation and result interpretation, longer time, etc. that ultimately makes it exhausting and expensive. Although there are a lot of improvements in the medical facilities in the Indian healthcare system, the use of POC diagnostic devices is still in its nascent phase. This review illustrates the status of POC diagnostic devices currently used in clinical setups along with constraints in their use. The devices and technologies that are in the research and development phase across the country that has tremendous potential to elevate the clinical diagnostics scenario along with the diagnosis of ongoing COVID-19 pandemic are emphasized. The implications of using POC diagnostic devices and the future objectives for technological advancements that may eventually uplift the status of healthcare and related sectors in India are also discussed here.