Effects of dilution and pretreatment on nutrient removal and biomass production of Chlorella vulgaris in kitchen wastewater.

This research investigated the effect of kitchen wastewater (KWW) concentrations and pretreatment methods on Chlorella vulgaris biomass production, lipid content and nutrient removal. This study was divided into two separate experiments. The first experiment determined the appropriate dilution rate of KWW for the growth of microalgae, sterilized KWW was varied between 25%, 50%, 75%, and 100%(v/v). The result indicated that 50%(v/v) showed the highest nutrient removal by 90.23%, 85.87%, and 80.64% of sCOD, TKN, and TP, respectively. The highest biomass and lipid content were obtained with 50%(v/v) (1.447 g/L, 37.9%). The second experiment was to find an effective physical pretreatment method, which separated the biotic contaminant, non-sterilized KWW was diluted 50%(v/v) and filtered with different mesh size filters (150 µm, 50 µm, and 30 µm) compared with sterilized KWW as a control sample. The result indicated that pretreatment with 50 µm filtration was found highest nutrient removal by 90.51%, 84.74%, and 77.50% of sCOD, TKN, and TP, respectively. The highest biomass and lipid content were obtained with 50 µm filtration (1.496 g/L, 39.4%). Our results support the hypothesis that the optimal dilution and proper filtration of KWW helps create more favorable environment for microalgal growth.

The application of microalgae in actual wastewater treatment was the improper amount of nutrients and the presence of biotic contaminant in the non-sterilized wastewater, which is inhibit the microalgae growth. Hence, it is necessary to develop the technique for controlling biotic contamination and appropriately diluting wastewater to enable full-scale microalgae cultivation in the future.

Monolith or Powder: Improper Sample Pretreatment May Mislead the Understanding of Industrial V2O5-WO3/TiO2 Catalysts Operated in Stationary Resources.

Although various characterizations are widely applied to commercial V2O5-WO3/TiO2 catalysts, the influence of the catalyst physical structure, i.e., monolith or powder, on the characterization results has not been investigated. Several important catalytic behaviors and phenomena were observed in this study using V2O5-WO3/TiO2 monolithic catalysts employed for over 5000 h in various stationary flue gases, and many of the results were only observable on monolithic catalysts, such as depth-dependent distribution of external elements, penetration of As2O3, and the formation of Tl2O-TiO2 p-n junctions. If the monolith is ground into powder states, it will alter or destroy the catalyst surface and remove important clues closely related to catalytic performance under working conditions. The redox and acidity properties of V2O5-WO3/TiO2 obtained from powder samples may be significantly different from their true state under working conditions, resulting in a misperception of catalyst performance. Therefore, a cautious pretreatment should be taken into careful consideration when analyzing commercial honeycomb V2O5-WO3/TiO2 catalysts.

Rapid, Simultaneous, and Automatic Determination of Lead and Cadmium in Cereals with a New High Performance Composite Hollow Cathode Lamp Coupled to Graphite Furnace Atomic Absorption Spectrometry.

A simple, rapid, sensitive, accurate, and automatic graphite furnace atomic absorption spectrometry (GFAAS) method for detecting Cd and Pb in cereals is presented. This method enables the simultaneous determination of Cd and Pb in cereals with a pre-treatment method of diluted acid extraction and a high-performance lead-cadmium composite hollow-cathode lamp (LCC-HCL), and it realizes automatic determination from sample weighing to result output through an automatic diluted acid extraction system. Under the optimization, Pb and Cd in cereals were simultaneously and automatically detected in up to 240 measurements in 8 h. The LOD and LOQ of this method were 0.012 and 0.040 mg·kg-1 for Pb, and 0.0014 and 0.0047 mg·kg-1 for Cd, respectively. The results of the four certified reference materials were satisfied; there was no significant difference compared with the ICP-MS method according to a t-test, and the RSDs were less than 5% for Cd and Pb. The recoveries of naturally contaminated samples compared with the ICP-MS method were favorable, with 80-110% in eight laboratories. The developed method is rapid, low-cost, and highly automated and may be a good choice for grain quality discrimination and rapid analysis of Cd and Pb in different institutions.

Development of a colloidal gold immunochromatographic strip for the rapid detection of pefloxacin in grass carp with a novel pretreatment method.

A rapid colloidal gold immunochromatography assay (GICA) for the detection of pefloxacin (PEF) was established and optimized. The anti-PEF monoclonal antibody (mAb) was used to target PEF as a colloidal gold-mAb conjugate. The mAb belonged to the IgG2b subtype, lambda light chain, the affinity constant (Ka) was 5.21 × 109 L·mol-1, and its half maximal inhibitory concentration (IC50) was 0.23 ng·mL-1. No obvious cross-reactivity (CR) was observed with other common fluoroquinolone antibiotics, including ciprofloxacin (CIP), norfloxacin (NOR), lomefloxacin (LOM) and ofloxacin (OFL). The visual limit of detection (vLOD) of the optimized GICA was 2 ng·g-1 under the conventional pretreatment method, and the assay was completed in 15 min. Liquid chromatography tandem-mass spectrometry (LC-MS/MS) was employed to confirm the performance of the strip. In addition, a novel pretreatment was established and compared with conventional pretreatment. Without the removal of organic solvents, the novel pretreatment method reduced the sample pretreatment time (more than 10 min). The vLOD of the optimized GICA was also 2 ng·g-1 when applying the novel pretreatment method. In conclusion, the proposed PEF-GICA could detect samples containing PEF rapidly and accurately, and the novel pretreatment method saved the time of sample pretreatment and improved the efficiency of detection.

Modern microextraction techniques for natural products.

Natural product analysis has gained wide attention in recent years, especially for herbal medicines, which contain complex ingredients and play a significant clinical role in the therapy of numerous diseases. The constituents of natural products are usually found at low concentrations, and the matrices are complex. Thus, the extraction of target compounds from natural products before analysis by analytical instruments is very significant for human health and its wide application. The commonly used traditional extraction methods are time-consuming, using large amounts of sample and organic solvents, as well as expensive and inefficient. Recently, microextraction techniques have been used for natural product extraction to overcome the disadvantages of conventional extraction methods. In this paper, the successful applications of and recent developments in microextraction techniques including solvent-based and sorbent-based microextraction methods, in natural product analysis in recent years, especially in the last 5 years, are reviewed for the first time. Their features, advantages, disadvantages, and future development trends are also discussed.

Rapid Quantitative Detection of Deltamethrin in Corydalis yanhusuo by SERS Coupled with Multi-Walled Carbon Nanotubes.

With the increase in demand, artificially planting Chinese medicinal materials (CHMs) has also increased, and the ensuing pesticide residue problems have attracted more and more attention. An optimized quick, easy, cheap, effective, rugged and safe (QuEChERS) method with multi-walled carbon nanotubes as dispersive solid-phase extraction sorbents coupled with surface-enhanced Raman spectroscopy (SERS) was first proposed for the detection of deltamethrin in complex matrix Corydalis yanhusuo. Our results demonstrate that using the optimized QuEChERS method could effectively extract the analyte and reduce background interference from Corydalis. Facile synthesized gold nanoparticles with a large diameter of 75 nm had a strong SERS enhancement for deltamethrin determination. The best prediction model was established with partial least squares regression of the SERS spectra ranges of 545~573 cm-1 and 987~1011 cm-1 with a coefficient of determination (R2) of 0.9306, a detection limit of 0.484 mg/L and a residual predictive deviation of 3.046. In summary, this article provides a new rapid and effective method for the detection of pesticide residues in CHMs.

Mass spectrometric analysis of free fatty acids in infant milk powders by frozen pretreatment coupled with isotope-labeling derivatization.

In combination with frozen pretreatment and carboxyl group derivatization, a novel workflow was developed for the determination of free fatty acids in milk powder. The workflow showed a significantly enhanced performance for comprehensive free fatty acid analysis owing to a highly efficient frozen extraction method. In addition, the advantages of the workflow also involved high sensitivity and great tolerance to a complex matrix. Characteristic fragment ions of derivatization reagents also provide clear evidence for the qualitative analysis of free fatty acids. Fourteen types of free fatty acids in a number of domestic and overseas infant milk powders have been successfully detected. The content of free fatty acids in the different samples was different, which probably indicates the diverse quality of infant milk powder. The workflow is expected to be a pragmatic tool for the analysis of free fatty acids in intricate matrices.

Optimization and application of pretreatment method of microplastics detection in municipal solid waste landfills.

The landfill is one of the most important sources of microplastics (MPs). The pretreatment method is a precondition of microplastics study for the presence of complex substances in landfills. Therefore, it is essential to examine the impact of different pretreatment methods on the microplastics detection. A literature review and a comparison experiment on digestion solutions were performed to establish a comprehensive identification method for MPs in landfills. When exposed to of 30 % H2O2, minimal mass reduction of PE, PP and PET were 4.00 %, 3.00 % and 3.00 % respectively, and the least surface damage was observed in MPs, while exhibiting the most optimal peak value for infrared spectral characteristics. It is demonstrated that the effect of 30 % H2O2 dissolution was superior compared to 10 % KOH and 65 % HNO3. The method was subsequently utilized to investigate the distribution of MPs in a landfill. The dominant MPs were polyethylene (PE, 18.56-23.91 %), polyethylene terephthalate (PET, 8.80-18.66 %), polystyrene (PS, 10.31-18.09 %), and polypropylene (PP, 11.60-14.91 %). The comprehensive identification method of "NaCl density separation + 30 % H2O2 digestion + NaI density separation + sampling microscope + Mirco-FTIR" is suitable for the detection of MPs in landfills.

The matrix effect derived from proteins in fluorescence detection for ciprofloxacin residues in eggs.

Based on the previously developed Al3+/CuNCs probe, the matrix effect (ME) derived from protein was investigated in the fluorescence determination of fluoroquinolones (FQs) residues in eggs, and a sample pretreatment method was established to rapidly reduce the ME. Molecular docking results indicated that the three main egg proteins and FQs were bound by hydrogen bond, van der Waals force, and alkyl groups, leading to the loss of FQs response signal, and then produced ME. After trichloroacetic acid treatment, the mean particle size of egg matrix decreased, the protein secondary structure changed, and the crystal structure was destroyed. The corresponding ME of the supernatant obtained by centrifugation was only 0.7 %. The standard addition experiment confirmed that the proposed pretreatment method improved the accuracy and reliability of the fluorescence probe. This work is helpful to promote the practical application of fluorescence analysis in the rapid monitoring of food safety hazard factors.

A novel pretreatment method for analysis the oxygen isotopic compositions of inorganic phosphorus pools in freshwater sediment.

Identifying the sources and cycling of phosphorus (P) is particularly important for formulating effective P management strategies in inland water. The oxygen isotopic compositions of phosphate (δ18OP) are recognized as a promising tool to solve this problem. However, the application of δ18OP in freshwater sediment is currently constrained by multiple difficulties. In this study, we presented a novel pretreatment method for δ18OP analysis of sediment inorganic P pools. Our results showed that the new method has advantages of simple operation, less time-consuming, and high P recovery rates. Specifically, we replaced the traditional Mg-induced co-precipitation (MAGIC) method by introducing Zr-Oxides gels with high selective adsorption function for phosphate. This made subsequent processing simpler and reduced the time consumption to ∼10 days, and the range of P recovery rates were from 88 % to 104 %. Furthermore, we emphasized the necessity of vacuum roasting following lyophilized Ag3PO4 to eliminate residual oxygen-containing impurities (e.g., NO3-, Ag2O, and organic matter). Additionally, evidences from microscopy and spectroscopy confirmed that this method ultimately yielded high-purity Ag3PO4 with the Ag:P molar ratios of 3.35:1. Importantly, combining direct synthesis Ag3PO4 between KH2PO4 and AgNO3 with the Ag3PO4 obtained by the method revealed no stark oxygen isotopic fractionation of phosphate during the pretreatment processes. The newly established δ18OP pretreatment methods here can also be extended to broader studies of the biogeochemical cycling of P in aquatic ecosystems, potentially advancing the understanding of the global P cycle.

An ultra-efficient pretreatment method adopted LPUV/CoFe2O4/PMS-based photolysis for accurate detection of Cd(II) and Pb(II) in water via SWASV.

Dissolved organic matter (DOM) is a widely occurring substance in rivers that can strongly complex with heavy metal ions (HMIs), severely interfering with the electrochemical signal of anodic stripping voltammetry (ASV) and reducing the detection accuracy of HMIs in water. In this study, we investigated a novel advanced oxidation process (AOP) that involves the activation of peroxymonosulfate (PMS) using low-pressure ultraviolet (LPUV) radiation and CoFe2O4 photocatalysis. This novel AOP was used for the first time as an effective pretreatment method to break or weaken the complexation between HMIs and DOM, thereby restoring the electrochemical signals of HMIs. The key parameters, including the PMS concentration, CoFe2O4 concentration, and photolysis time, were optimized to be 6 mg/L, 12 mg/L, and 30 s for eliminating DOM interference during the electrochemical analysis of HMIs via LPUV/CoFe2O4-based photolysis. Investigations of the microstructure, surface morphology, specific surface area, and pore volume of CoFe2O4 were conducted to reveal the exceptional signal recovery capability of LPUV/CoFe2O4/PMS-based photolysis in mitigating interference from DOM during HMIs analysis. The PMS activation mechanism, which is critical to the signal recovery process, was elucidated by analyzing the reactive oxygen species (ROS) and the surface elemental composition of CoFe2O4. Additionally, the degradation and transformation behavior of humus-HMIs complexes were analyzed to study the mechanism of ASV signal recovery further. Notably, the detection results of HMIs in actual water samples obtained using the proposed pretreatment method were compared with those obtained from ICP-MS, yielding an RMSE less than 0.04 µg/L, which indicated the satisfactory performance of the proposed pretreatment method for the ASV detection of HMIs in complex actual samples.

Characterization of the aroma-active compounds in Xiaokeng green tea by three pretreatment methods combined with gas chromatography-olfactometry (GC-O).

Chinese Xiaokeng green tea (XKGT) possesses elegant and fascinating aroma characteristics, but its key odorants are still unknown. In this study, 124 volatile compounds in the XKGT infusion were identified by headspace-solid phase microextraction (HS-SPME), stir bar sorptive extraction (SBSE), and solvent extraction-solid phase extraction (SE-SPE) combined with gas chromatography-mass spectrometry (GC-MS). Comparing these three pretreatments, we found HS-SPME was more efficient for headspace compounds while SE-SPE was more efficient for volatiles with higher boiling points. Furthermore, SBSE showed more sensitive to capture ketones then was effective to the application of pretreatment of aroma analysis in green tea. The aroma intensities (AIs) were further identified by gas chromatography-olfactometry (GC-O). According to the AI and relative odor activity value (rOAV), 27 compounds were identified as aroma-active compounds. Quantitative descriptive analysis (QDA) showed that the characteristic aroma attributes of XKGT were chestnut-like, corn-like, fresh, and so on. The results of network analysis showed that (E, Z)-2,6-nonadienal, nonanal, octanal and nerolidol were responsible for the fresh aroma. Similarly, dimethyl sulfide, (E, E)-2,4-heptadienal, (E)-2-octenal and ß-cyclocitral contributed to the corn-like aroma. Furthermore, indole was responsible for the chestnut-like and soybean-like aroma. This study contributes to a better understanding of the molecular mechanism of the aroma characteristics of XKGT.

Effect of Pretreatments on the Chemical, Bioactive and Physicochemical Properties of Cinnamomum camphora Seed Kernel Extracts.

Cinnamomum camphora seed kernels (CCSKs) are rich in phytochemicals, especially plant extracts. Phytochemicals play a vital role in therapy due to their strong antioxidant and anti-inflammatory activities. Extracts from CCSK can be obtained through multiple steps, including pretreatment, extraction and purification, and the purpose of pretreatment is to separate the oil from other substances in CCSKs. However, C. camphora seed kernel extracts (CKEs) were usually considered as by-products and discarded, and their potential bioactive values were underestimated. Additionally, little has been known about the effect of pretreatment on CKE. This study aimed to investigate the effects of pretreatment methods (including the solvent extraction method, cold pressing method, aqueous extraction method and sub-critical fluid extraction method) on the extraction yields, phytochemical profiles, volatile compounds and antioxidant capacities of different CKE samples. The results showed that the CKE samples were rich in phenolic compounds (15.28-20.29%) and alkaloids (24.44-27.41%). The extraction yield, bioactive substances content and in vitro antioxidant capacity of CKE pretreated by the sub-critical fluid extraction method (CKE-SCFE) were better than CKEs obtained by other methods. CKE pretreated by the solvent extraction method (CKE-SE) showed the best lipid emulsion protective capacity. Moreover, the volatile substances composition of the CKE samples was greatly influenced by the pretreatment method. The results provided a fundamental basis for evaluating the quality and nutritional value of CKE and increasing the economic value of by-products derived from CCSK.

Differences in the effectiveness of the high-efficient concentrated pretreatment method on the norovirus detection in oysters and mussels.

Oysters and mussels are important vectors for norovirus (NoV). An efficient pretreatment method for NoV detection in oysters based on ISO 15216-2:2019 was established in our previous work, but its effectiveness for other types of shellfish remains unknown. Therefore, this study systematically compared the differences between the standard and modified ISO methods in detecting NoV for oysters and mussels. Using the standard ISO method, the recovery rates of NoV in oysters (2.10 ± 0.80 %) and mussels (2.39 ± 0.56 %) were comparable (p > 0.05, unpaired t-test). In contrast, the virus recovery rates in oysters (19.83 ± 3.64 %) and mussels (46.96 ± 3.55 %) were both significantly improved by the modified method. Also, a significant difference was found between the virus recovery rates in two shellfish (p < 0.05, unpaired t-test), resulting in a 2.09-fold difference in their virus concentrations. Additionally, the limits of detection at 95 % probability of the modified ISO method for oysters and mussels could both reach 3.33 × 103 copies/g of digestive glands. Finally, the modified ISO method has been successfully applied in commercial oysters (14/27, 51.85 %) and mussels (15/23, 65.22 %), and the results indicated a significant difference in NoV recovery rates between two shellfish (p < 0.05, one-way analysis of variance). In summary, the modified ISO method showed higher virus recovery rates than the standard ISO method, which would be used as an essential tool for NoV detection in oysters and mussels.

Influence of Pretreatment Methods on Compressive Performance Improvement and Failure Mechanism Analysis of Recycled Aggregate Concrete.

The utilization of recycled aggregate can avert the squandering of resources and the destruction of the environment. Nevertheless, there exists a slew of old cement mortar and microcracks on the surface of recycled aggregate, which give rise to the poor performance of aggregates in concrete. In this study, for the sake of ameliorating this property of recycled aggregates, the surface of the recycled aggregates is covered with a layer of cement mortar to compensate for the microcracks on the surface and reinforce the bond between old cement mortar and aggregates. In order to demonstrate the influence of recycled aggregate by different cement mortar pretreatment methods, this study prepared natural aggregate concrete (NAC) and concretes with recycled aggregate after the wetting pretreatment (RAC-W) and cement mortar pretreatment (RAC-C), and conducted uniaxial compressive strength tests on different types of concrete at different curing ages. The test results indicated that the compressive strength of RAC-C at a 7 d curing age was higher than that of RAC-W and NAC, and the compressive strength of RAC-C at a 28 d curing age was higher than RAC-W but lower than NAC. The compressive strength of NAC and RAC-W at a 7 d curing age was about 70% of that at a 28 d curing age, and the compressive strength of RAC-C at a 7 d curing age was about 85-90% of that at a 28 d curing age. The compressive strength of RAC-C increased dramatically at the early stage, while the post-strength of the NAC and RAC-W groups increased rapidly. The fracture surface of RAC-W mainly occurred in the transition zone between the recycled aggregates and old cement mortar under the pressure of the uniaxial compressive load. However, the main failure of RAC-C was the crushing destruction of cement mortar. With changes in the amount of cement added beforehand, the proportion of aggregate damage and A-P interface damage of RAC-C also changed accordingly. Therefore, the recycled aggregate pretreated with cement mortar can significantly improve the compressive strength of recycled aggregate concrete. The optimal amount of pre-added cement was 25%, which is recommended for practical engineering.

Improved 31P NMR analysis of phosphorus in highly mineralized lake water using a modified pretreatment procedure with H resin.

31P Nuclear Magnetic Resonance (31P NMR) is an important analytical tool for identifying and quantifying phosphorus-based compounds in aquatic environments. However, the precipitation method typically used for analyzing phosphorus species via 31P NMR has limited application. To expand the scope of the method and apply it to highly mineralized rivers and lakes worldwide, we present an optimization technique that employs H resin to assist phosphorus (P) enrichment in highly mineralized lake water. To explore how to reduce analysis interference from salt in highly mineralized water and improve the accuracy of P analysis using 31P NMR, we conducted case studies on Lake Hulun and Qing River. This study aimed to increase the efficiency of phosphorus extraction in highly mineralized water samples by using H resin and optimizing key parameters. The optimization procedure included determining the enriched water volume, H resin treatment time, AlCl3 addition amount, and precipitation time. The final recommended optimization enrichment procedure involves treating 10 L of filtered water sample with 150 g of Milli-Q water-washed H resin for 30 s, adjusting the pH of the treated sample to 6-7, adding 1.6 g of AlCl3, stirring the mixture, and allowing the solution to settle for 9 h to collect the flocculated precipitate. The precipitate was then extracted with 30 mL of 1 M NaOH +0.05 M DETA extraction solution at 25 °C for 16 h, and the supernatant was separated and lyophilized. The lyophilized sample was redissolved in 1 mL of 1 M NaOH +0.05 M EDTA. This optimized analytical method using 31P NMR effectively identified phosphorus species in highly mineralized natural waters and can be applied to other highly mineralized lake waters globally.

Optimization framework of sediment phosphate oxygen isotope pretreatment method based on large-scale application: A case study of Fuyang River basin.

Phosphate oxygen isotope (δ18OP) technique is an effective tool to identify the source and transformation process of phosphorus. The poor applicability of existing δ18OP pretreatment methods for sediments hindered the large-scale application of δ18OP technology. This paper presents an optimization framework for the pretreatment of sediment δ18OP samples based on large-scale applications, using the Fuyang River Basin as a case study. The typical channel landscape outflow lake, South Lake, was selected as the most favorable point for assessing the applicability and optimizing the mainstream δ18OP pretreatment method, which was achieved by clarifying the sediment environmental characteristics of South Lake. To evaluate the suitability of the Blake and McLaughlin methods in South Lake, a comparative study was carried out based on five dimensions: phosphorus recovery rate, removal efficiency of organic matter, removal efficiency of extraction liquid impurity ion, experimental time, and reagent consumption cost. The findings demonstrated that the Blake method outperformed the McLaughlin method across all five dimensions. Based on the environmental characteristics of the sediments of South Lake, the Blake method was optimized from two perspectives, namely the substitution of reagents and adjustment and optimization of experimental procedures. This resulted in an enhancement of phosphorus recovery and organic matter removal efficiency, while also reducing the experimental time required. The optimized method also yielded satisfactory results when applied to the entire watershed. This research paper can thus offer valuable technical support for the widespread application of sediment δ18OP technology.

Characterization of bioactives and in vitro biological activity from Protaetia brevitarsis larval extracts obtained by different pretreatment extractions.

Intestinal contents affect the characterization of edible insect bioactive compounds. Two empty intestine methods, namely, traditional static method (TSM) or salt immersion stress method (SISM), associated with extraction solvents water (W), 50 % water-ethanol (W:E) or 100 % ethanol (E), were used to obtain six Protaetia brevitarsis larval extracts. The total flavonoid content (TFC) in the W:E extracts was significantly higher than that in the W and E extracts, with TSM-W:E the highest (p < 0.05). The relative contents of 132 bioactive compounds, especially p-hydroxyphenylacetic acid, citric acid, and dehydroepiandrosterone, were different between TSM-W and SISM-W. TSM-W:E had significantly higher 2,2-diphenyl-1-picrylhydroxy· (DPPH) scavenging and pancreatic lipase (PL) inhibitory activity than SISM-W:E (p < 0.05). DPPH scavenging and PL inhibitory activities were highly correlated with TFC and carbohydrates, respectively. Thus, bioactive compounds in P. brevitarsis extracts can be obtained selectively using pretreatment methods, which might be beneficial for high-value utilization of P. brevitarsis.

Fabrication and application of hydrangea-like magnetic titanium dioxide (Fe3O4-TiO2) particles: Development of magnetic "one-step" pretreatment method for multi-pesticide residues analysis in fish.

Magnetic titanium dioxide (Fe3O4-TiO2) was prepared and utilized as the cleanup adsorbent and separation medium to modify the QuEChERS method, affording a facile, robust, and rapid magnetic "one-step" pretreatment method for the determination of multi-pesticide residues in fish. The pretreatment key parameters, such as the dosages of the purification adsorbents (Fe3O4-TiO2 and PSA), the dehydrating and salting out reagents, were systematically optimized by the orthogonal test method. Under the optimal conditions, satisfactory results of method evaluation were obtained. Good linearity of 127 target analytes was obtained from 1 to 250 µg L-1. The recoveries of 127 analytes at five spiked levels of 10, 25, 50, 125, and 250 µg kg-1 ranged from 71.0% to 129% with RSDs less than 15.0%. The method LOQs (MLOQs) of 127 analytes were 10 µg kg-1, meeting the requirement for multi-pesticide residues analysis in fish. Additionally, this magnetic "one-step" method was used for the analysis of multi-pesticide residues in real fish samples collected from Zhejiang Province, China. In summary, this method can work as a viable tool for multi-pesticide residues monitoring in fish.

The pretreatment method in marine organisms and sediment for microplastics analysis by FTIR using "Cylindrical microplastics fractionator".

For the detection of microplastics (MPs) in aquatic biota using Fourier transform infrared spectroscopy (FTIR), the ability to remove organic matter (OM) in pretreatment steps is essential to increase the time efficiency of MPs measurement and method uniformity. In principle, decreasing OM can be achieved by increasing the number of pretreatment steps. However, MPs are lost in proportion to the number of transfers between each step. Therefore, we have created a "Cylindrical MPs Fractionator" composed of commercially available materials. This container allows for a six-step pretreatment process that is designed to increase the removal capacity of OM with only one transfer to prevent the loss of MPs.•Biological or sediment samples are placed in the extractor and subjected to chemical treatment and density separation.•Residues containing MPs are obtained on filters by vacuum filtration.•After additional chemical treatment of the obtained residue, the components of the residue are identified by microscopic FTIR.This method removed 99.3% of OM and recovered 88.5% of MPs. The presenting method confirmed that this can be used with the same process for 11 organisms and sediments from estuarine ecosystem in Japan as models.