Optimizing Photoelectrochemical UV Imaging Photodetection: Construction of Anatase/Rutile Heterophase Homojunctions and Oxygen Vacancies Engineering in MOF-Derived TiO2.

Self-powered photoelectrochemical (PEC) ultraviolet photodetectors (UVPDs) are promising for next-generation energy-saving and highly integrated optoelectronic systems. Constructing a heterojunction is an effective strategy to increase the photodetection performance of PEC UVPDs because it can promote the separation and transfer of photogenerated carriers. However, both crystal defects and lattice mismatch lead to deteriorated device performance. Here, we introduce a structural regulation strategy to prepare TiO2 anatase-rutile heterophase homojunctions (A-R HHs) with oxygen vacancies (OVs) photoanodes through an in situ topological transformation of titanium metal-organic framework (Ti-MOF) by pyrolysis treatment. The cooperative interaction between A-R HHs and OVs suppresses carrier recombination and accelerates carrier transport, thereby significantly enhancing the photodetection performance of PEC UVPDs. The obtained device realizes a high on/off ratio of 10,752, a remarkable responsivity of 24.15 mA W-1, an impressive detectivity of 3.28 × 1011 Jones, and excellent cycling stability. More importantly, under 365 nm light illumination, a high-resolution image of "HUST" (the abbreviation of Harbin University of Science and Technology) was obtained perfectly, confirming the excellent optical imaging capability of the device. This research not only presents an advanced methodology for constructing TiO2-based PEC UVPDs, but also provides strategic guidance for enhancing their performance and practical applications.

Design and Development of an Ultraviolet All-Sky Imaging System.

All-sky cameras capture a panoramic view of the full sky from horizon to horizon to generate a wide-angle image of the observable sky. State-of-the-art all-sky imagers are limited to imaging in the visible and infrared spectrum and cannot image in the UV spectrum. This article describes the development of an all-sky imaging system capable of capturing 130° wide-angle sky images from horizon to horizon in the UV-AB spectrum. The design of the UV all-sky imaging system is based on low-cost, accessible, and scalable components to develop multiple images that can be deployed over a wider geographical area. The spectral response of the camera system has been validated in the UV spectrum (280-420 nm) using a monochromatic UV beam with an average power output of 22 nW. UV all-sky imaging systems complement existing infrared and visible all-sky cameras. They have wide applications in astronomy, meteorology, atmospheric science, vulcanology, meteors and auroral monitoring, and the defence sector.

Real-Time Monitoring of SO2 Emissions Using a UV Camera with Built-in NO2 and Aerosol Corrections.

Nitrogen dioxide (NO2) absorption correction of the sulfur dioxide (SO2) camera was demonstrated for the first time. The key to improving the measurement accuracy is to combine a differential optical absorption spectroscopy (DOAS) instrument with the SO2 camera for the real-time NO2 absorption correction and aerosol scattering correction. This method performs NO2 absorption correction by the correlation between the NO2 column density measurement of the DOAS and the NO2 optical depth of the corresponding channel from the SO2 camera at a narrow wavelength window around 310 and 310 nm. The error of correction method is estimated through comparison with only using the second channel of the traditional SO2 camera to correct for aerosol scattering and it can be reduced by 11.3% after NO2 absorption corrections. We validate the correction method through experiments and demonstrate it to be of greatly improved accuracy. The result shows that the ultraviolet (UV) SO2 camera system with NO2 absorption corrections appears to have great application prospects as a technology for visualized real-time monitoring of SO2 emissions.

Methodological Considerations in Development of UV Imaging for Characterization of Intra-Tumoral Injectables Using cAMP as a Model Substance.

A UV imaging release-testing setup comprising an agarose gel as a model for tumorous tissue was developed. The setup was optimized with respect to agarose concentration (0.5% (w/v)), injection procedure, and temperature control. A repeatable injection protocol was established allowing injection into cavities with well-defined geometries. The effective resolution of the SDi2 UV imaging system is 30-80 µm. The linear range of the imaging system is less than that of typical spectrophotometers. Consequently, non-linear cAMP calibration curves were applied for quantification at 280 nm. The degree of deviation from Beer's law was affected by the background absorbance of the gel matrix. MATLAB scripts provided hitherto missing flexibility with respect to definition and utilization of quantification zones, contour lines facilitating visualization, and automated, continuous data analysis. Various release patterns were observed for an aqueous solution and in situ forming Pluronic F127 hydrogel and PLGA implants containing cAMP as a model for STING ligands. The UV imaging and MATLAB data analysis setup constituted a significant technical development in terms of visualizing behavior for injectable formulations intended for intra-tumoral delivery, and, thereby, a step toward establishment of a bio-predictive in vitro release-testing method.

A novel UV-fluorescence approach to assess the long wear efficacy of foundations.

BACKGROUND: The long wear properties of foundations are regarded as a must-have in terms of claims. Here, we propose an instrumental approach based on UV-fluorescence imaging as an alternative to clinical grading methods. METHODS: A method was developed, with UV-fluorescence images captured with the Visia CR as a first step, followed by images analysis using Image-Pro plus. Repeated-measures correlation was used to assess the degree of association between the UV-fluorescence method and a grading method when removing the foundation incrementally from the skin using wipes. Thresholds to ascertain whether a foundation pass or fail long-wearing using the newly developed method were established using a mixed linear model and cross-validated using two subsets of a panel of 20 women. RESULTS: The method could measure incremental removal of foundation using wipes, in a similar fashion to a grading method, as outlined with repeated measures correlation (r = -.86). Pass/fail thresholds established with the mixed linear model were tested versus the grading method when assessing a foundation under real conditions for a duration over 24 hours, with minimal discrepancies between the two methods. CONCLUSION: By capitalising on foundation physical/chemical properties, the proposed method allows to assess their long wear properties, irrespective of basal skin tone or foundation shade. It offers the advantage of appealing visuals for efficacy and to be less resource intensive than a clinical grading approach.

Surface Dissolution UV Imaging for Investigation of Dissolution of Poorly Soluble Drugs and Their Amorphous Formulation.

The aim of this study is to investigate the dissolution properties of poorly soluble drugs from their pure form and their amorphous formulation under physiological relevant conditions for oral administration based on surface dissolution ultraviolet (UV) imaging. Dissolution of two poorly soluble drugs (cefuroxime axetil and itraconazole) and their amorphous formulations (Zinnat® and Sporanox®) was studied with the Sirius Surface Dissolution Imager (SDI). Media simulating the fasted state conditions (compendial and biorelevant) with sequential media/flow rate change were used. The dissolution mechanism of cefuroxime axetil in simulated gastric fluid (SGF), fasted state simulated gastric fluid (FaSSGF) and simulated intestinal fluid (SIF) is predominantly swelling as opposed to the convective flow in fasted state simulated intestinal fluid (FaSSIF-V1), attributed to the effect of mixed micelles. For the itraconazole compact in biorelevant media, a clear upward diffusion of the dissolved itraconazole into the bulk buffer solution is observed. Dissolution of itraconazole from the Sporanox® compact is affected by the polyethylene glycol (PEG) gelling layer and hydroxypropyl methylcellulose (HPMC) matrix, and a steady diffusional dissolution pattern is revealed. A visual representation and a quantitative assessment of dissolution properties of poorly soluble compounds and their amorphous formulation can be obtained with the use of surface dissolution imaging under in vivo relevant conditions.

A Hybrid Readout Solution for GaN-Based Detectors Using CMOS Technology.

Gallium nitride (GaN) and its alloys are becoming preferred materials for ultraviolet (UV) detectors due to their wide bandgap and tailorable out-of-band cutoff from 3.4 eV to 6.2 eV. GaN based avalanche photodiodes (APDs) are particularly suitable for their high photon sensitivity and quantum efficiency in the UV region and for their inherent insensitivity to visible wavelengths. Challenges exist however for practical utilization. With growing interests in such photodetectors, hybrid readout solutions are becoming prevalent with CMOS technology being adopted for its maturity, scalability, and reliability. In this paper, we describe our approach to combine GaN APDs with a CMOS readout circuit, comprising of a linear array of 1 × 8 capacitive transimpedance amplifiers (CTIAs), implemented in a 0.35 µm high voltage CMOS technology. Further, we present a simple, yet sustainable circuit technique to allow operation of APDs under high reverse biases, up to ≈80 V with verified measurement results. The readout offers a conversion gain of 0.43 µV/e-, obtaining avalanche gains up to 10³. Several parameters of the CTIA are discussed followed by a perspective on possible hybridization, exploiting the advantages of a 3D-stacked technology.

Application of UV Imaging in Formulation Development.

Efficient drug delivery is dependent on the drug substance dissolving in the body fluids, being released from dosage forms and transported to the site of action. A fundamental understanding of the interplay between the physicochemical properties of the active compound and pharmaceutical excipients defining formulation behavior after exposure to the aqueous environments and pharmaceutical performance is critical in pharmaceutical development, manufacturing and quality control of drugs. UV imaging has been explored as a tool for qualitative and quantitative characterization of drug dissolution and release with the characteristic feature of providing real-time visualization of the solution phase drug transport in the vicinity of the formulation. Events occurring during drug dissolution and release, such as polymer swelling, drug precipitation/recrystallization, or solvent-mediated phase transitions related to the structural properties of the drug substance or formulation can be monitored. UV imaging is a non-intrusive and simple-to-operate analytical technique which holds potential for providing a mechanistic foundation for formulation development. This review aims to cover applications of UV imaging in the early and late phase pharmaceutical development with a special focus on the relation between structural properties and performance. Potential areas of future advancement and application are also discussed.

Role of Electrostatic Interactions on the Transport of Druglike Molecules in Hydrogel-Based Articular Cartilage Mimics: Implications for Drug Delivery.

In the field of drug delivery to the articular cartilage, it is advantageous to apply artificial tissue models as surrogates of cartilage for investigating drug transport and release properties. In this study, artificial cartilage models consisting of 0.5% (w/v) agarose gel containing 0.5% (w/v) chondroitin sulfate or 0.5% (w/v) hyaluronic acid were developed, and their rheological and morphological properties were characterized. UV imaging was utilized to quantify the transport properties of the following four model compounds in the agarose gel and in the developed artificial cartilage models: H-Ala-ß-naphthylamide, H-Lys-Lys-ß-naphthylamide, lysozyme, and α-lactalbumin. The obtained results showed that the incorporation of the polyelectrolytes chondroitin sulfate or hyaluronic acid into agarose gel induced a significant reduction in the apparent diffusivities of the cationic model compounds as compared to the pure agarose gel. The decrease in apparent diffusivity of the cationic compounds was not caused by a change in the gel structure since a similar reduction in apparent diffusivity was not observed for the net negatively charged protein α-lactalbumin. The apparent diffusivity of the cationic compounds in the negatively charged hydrogels was highly dependent on the ionic strength, pointing out the importance of electrostatic interactions between the diffusant and the polyelectrolytes. Solution based affinity studies between the model compounds and the two investigated polyelectrolytes further confirmed the electrostatic nature of their interactions. The results obtained from the UV imaging diffusion studies are important for understanding the effect of drug physicochemical properties on the transport in articular cartilage. The extracted information may be useful in the development of hydrogels for in vitro release testing having features resembling the articular cartilage.

Ultraviolet Imaging with Low Cost Smartphone Sensors: Development and Application of a Raspberry Pi-Based UV Camera.

Here, we report, for what we believe to be the first time, on the modification of a low cost sensor, designed for the smartphone camera market, to develop an ultraviolet (UV) camera system. This was achieved via adaptation of Raspberry Pi cameras, which are based on back-illuminated complementary metal-oxide semiconductor (CMOS) sensors, and we demonstrated the utility of these devices for applications at wavelengths as low as 310 nm, by remotely sensing power station smokestack emissions in this spectral region. Given the very low cost of these units, ≈ USD 25, they are suitable for widespread proliferation in a variety of UV imaging applications, e.g., in atmospheric science, volcanology, forensics and surface smoothness measurements.

Rapid Assessment of Tablet Film Coating Quality by Multispectral UV Imaging.

Chemical imaging techniques are beneficial for control of tablet coating layer quality as they provide spectral and spatial information and allow characterization of various types of coating defects. The purpose of this study was to assess the applicability of multispectral UV imaging for assessment of the coating layer quality of tablets. UV images were used to detect, characterize, and localize coating layer defects such as chipped parts, inhomogeneities, and cracks, as well as to evaluate the coating surface texture. Acetylsalicylic acid tablets were prepared on a rotary tablet press and coated with a polyvinyl alcohol-polyethylene glycol graft copolymer using a pan coater. It was demonstrated that the coating intactness can be assessed accurately and fast by UV imaging. The different types of coating defects could be differentiated and localized based on multivariate image analysis and Soft Independent Modeling by Class Analogy applied to the UV images. Tablets with inhomogeneous texture of the coating could be identified and distinguished from those with a homogeneous surface texture. Consequently, UV imaging was shown to be well-suited for monitoring of the tablet coating layer quality. UV imaging is a promising technique for fast quality control of the tablet coating because of the high data acquisition speed and its nondestructive analytical nature.

Influence of the frequency of laser toning for melasma on occurrence of leukoderma and its early detection by ultraviolet imaging.

BACKGROUND AND OBJECTIVE: Laser "toning" with a Q-switched neodymium-doped yttrium aluminum garnet (Nd:YAG) laser has recently been described to be effective for the treatment of melasma. Leukoderma is a refractory complication of laser toning for melasma, but it can be detected early with ultraviolet (UV) imaging. We assessed the relationship between leukoderma and the frequency or total number of laser toning sessions, as well as the effectiveness of UV imaging for detecting leukoderma. MATERIALS AND METHODS: The subjects included 147 patients who received at least five laser toning sessions. Subjects were classified into three groups according to the frequency of treatment (weekly for Group A1, fortnightly for Group A2, and monthly for Group B), and the incidence of leukoderma was compared among the three groups. In patients who developed leukoderma, the interval between clinical diagnosis and leukoderma detection on UV images (obtained with a Visia Evolution during every laser toning session) was determined to evaluate the effectiveness of UV imaging for the early detection of leukoderma. RESULTS: The overall incidence of leukoderma was 2% (3/147 patients): 3.8% (1/26 patients) in Group A1, 4% (2/49 patients) in Group A2, and 0% (0/72 patients) in Group B. There were no significant differences in the incidence of leukoderma relative to the frequency of laser toning. In two of the three patients who developed leukoderma, it was diagnosed clinically at the 20th and 21st laser toning session, whereas it was diagnosed by UV imaging at the 12th and 13th session. In the remaining 1 patient, leukoderma was detected clinically and by UV imaging at the 7th session. CONCLUSIONS: There was no significant difference in the incidence of leukoderma related to the frequency of laser toning. This study showed that there are two types of leukoderma associated with laser toning. UV imaging was effective for the early detection of type 1 leukoderma, which seems to be related to the cumulative laser energy delivered, but not for detecting type 2 leukoderma, which may be due to direct phototoxicity.

UV-VIS imaging-based investigation of API concentration fluctuation caused by the sticking behaviour of pharmaceutical powder blends.

Surface powder sticking in pharmaceutical mixing vessels poses a risk to the uniformity and quality of drug formulations. This study explores methods for evaluating the amount of pharmaceutical powder mixtures adhering to the metallic surfaces. Binary powder blends consisting of amlodipine and microcrystalline cellulose (MCC) were used to investigate the effect of the mixing order on the adherence to the vessel wall. Elevated API concentrations were measured on the wall and within the dislodged material from the surface, regardless of the mixing order of the components. UV imaging was used to determine the particle size and the distribution of the API on the metallic surface. The results were compared to chemical maps obtained by Raman chemical imaging. The combination of UV and VIS imaging enabled the rapid acquisition of chemical maps, covering a substantially large area representative of the analysed sample. UV imaging was also applied in tablet inspection to detect tablets that fail to meet the content uniformity criteria. The results present powder adherence as a possible source of poor content uniformity, highlighting the need for 100% inspection of pharmaceutical products to ensure product quality and safety.

UV imaging for the rapid at-line content determination of different colourless APIs in their tablets with artificial neural networks.

This paper presents a novel high-resolution and rapid (50 ms) UV imaging system, which was used for at-line, non-destructive API content determination of tablets. For the experiments, amlodipine and valsartan were selected as two colourless APIs with different UV induced fluorescent properties according to the measured solid fluorescent spectra. Images were captured with a LED-based UV illumination (385-395 nm) of tablets containing amlodipine or valsartan and common tableting excipients. Blue or green colour components from the RGB colour space were extracted from the images and used as an input dataset to execute API content prediction with artificial neural networks. The traditional destructive, solution-based transmission UV measurement was applied as reference method. After the optimization of the number of hidden layer neurons it was found that the relative error of the content prediction was 4.41 % and 3.98 % in the case of amlodipine and valsartan containing tablets respectively. The results open the possibility to use the proposed UV imaging-based system as a rapid, in-line tool for 100 % API content screening in order to greatly improve pharmaceutical quality control and process understanding.

Some practical guidelines for UV imaging in the protein crystallization laboratory.

High-throughput imaging of protein crystallization experiments with ultraviolet (UV) light has recently become commercially available and can enable crystallographers to differentiate between crystals of protein and those of salt, as the visualization of protein crystals is based on intrinsic tryptophan fluorescence. Unfortunately, UV imaging is not a panacea, as some protein crystals will not fluoresce under UV excitation and some salt crystals are UV-fluorescently active. As a new technology, there is little experience within the general community on how to use this technology effectively and what caveats to look out for. Here, an attempt is made to identify some of the common problems that may arise using UV-imaging technology by examining test proteins, common crystallization reagents and a range of proteins by assessing their UV-Vis absorbance spectra. Some pointers are offered as to which systems may not be appropriate for this methodology.

Drug diffusion in biomimetic hydrogels: importance for drug transport and delivery in non-vascular tumor tissue.

Hydrogels of varying complexity are routinely used as scaffolds and 3D structures for in vitro tumor models to increase physiological relevance within pre-clinical cancer research. Relatively simple hydrogels such as agarose are well characterised, meanwhile biomimetic gels containing collagen and fibrin(ogen) have been studied to a much lesser extent. In this study, hydrogels mimicking the biophysical characteristics of liver cancer progression were investigated in terms of their UV-properties and influence on diffusion coefficients of different substances. UV-imaging technology was used to both visualize and quantify the diffusion process in a simple and rapid way. In general, agarose gel diffusion agreed well with predictions using the Stokes-Einstein equation meanwhile the biomimetic gels reduced diffusion coefficients by up to 70%. For doxorubicin, spatio-temporal tissue concentration modelling was used to translate in vitro diffusion to the more clinical context of tumor penetration in a solid liver tumor supplied by arterial blood.

Low-Temperature Vapor-Phase Anion-Exchange Strategy for Wide-Bandgap Double-Perovskite Cs2AgBiCl6 Films toward Weak Ultraviolet Light Imaging.

Low-temperature synthesis of high-quality, high-stability, wide-bandgap perovskite films by solution methods is still challenging. Herein, large-scale wide-bandgap Cs2AgBiCl6 (CABC) double perovskite films are synthesized by a vapor-phase anion-exchange strategy. By dedicatedly designing an ultrathin TiO2 modification layer between the substrate and double perovskites, high-quality heterojunctions with matched energy band alignment are formed, contributing to a remarkably enhanced ON/OFF ratio of 2.4 × 104 (86 times) and a responsivity of 16 mA W-1 (12 times). Additionally, the ultraviolet photodetectors (UV PDs) exhibit an excellent UV detection limit of 1.18 µW cm-2 (20 nW), a broad linear dynamic range of 146 dB, and a high specific detectivity of 2.06 × 1011 Jones, as well as long-term stability. Finally, we further demonstrate a weak UV imaging system using CABC UV PDs as imaging sensors. The system is capable of imaging weak UV signals as low as 2.94 µW cm-2 (50 nW). Our results provide a feasible approach for low-temperature fabrication of wide-bandgap perovskite UV PDs and explore the promising application for weak UV detection and imaging.

Research progress on the application of spectral imaging technology in pharmaceutical tablet analysis.

Tablet as a traditional dosage form in pharmacy has the advantages of accurate dosage, ideal dissolution and bioavailability, convenient to carry and transport. The most concerned tablet quality attributes include active pharmaceutical ingredient (API) contents and polymorphic forms, components distribution, hardness, density, coating state, dissolution behavior, etc., which greatly affect the bioavailability and consistency of tablet final products. In the pharmaceutical industry, there are usually industry standard methods to analyze the tablet quality attributes. However, these methods are generally time-consuming and laborious, and lack a comprehensive understanding of the properties of tablets, such as spatial information. In recent years, spectral imaging technology makes up for the shortcomings of traditional tablet analysis methods because it provides non-contact and rich information in time and space. As a promising technology to replace the traditional tablet analysis methods, it has attracted more and more attention. The present paper briefly describes a series of spectral imaging techniques and their applications in tablet analysis. Finally, the possible application prospect of this technology and the deficiencies that need to be improved were also prospected.

Impact of Swelling of Spray Dried Dispersions in Dissolution Media on their Dissolution: An Investigation Based on UV Imaging.

Impact of SDD-dissolution medium interactions on the swelling and dissolution of spray dried dispersions (SDDs) was investigated using UV imaging by monitoring SDD swelling in situ, along with correlating of the swelling with the micro-dissolution and intrinsic dissolution of SDDs. SDDs of ketoconazole or indomethacin with three polymers: polyvinylpyrrolidone (PVP), hydroxypropyl cellulose (HPC), and hydroxypropyl methylcellulose acetate succinate (HPMC-AS) were prepared for the study. Dissolution media employed for assessing swelling and dissolution include water, acetate buffer, phosphate buffer, fasted state simulated intestinal fluid (FaSSIF), and fed state simulated intestinal fluid (FeSSIF), in which influence of polymers and drugs together with the physical-chemical properties of dissolution media (pH, and the presence of sodium taurocholate and lecithin) on SDD swelling and dissolution was evaluated. It appears that hydrophilic and hydrophobic properties of polymers can significantly impact SDD swelling and thus the dissolution. Furthermore, properties of dissolution media such as pH as well as presence of bile salts and lecithin seems to affect SDD swelling and dissolution as well. Throughout the text, thermodynamic swelling of polymers was used to interpret SDD dissolution behavior. Finally, practical implication of polymer swelling on dissolution was discussed.

In Situ Fabrication of PdSe2/GaN Schottky Junction for Polarization-Sensitive Ultraviolet Photodetection with High Dichroic Ratio.

Polarization-sensitive ultraviolet (UV) photodetection is of great technological importance for both civilian and military applications. Two-dimensional (2D) group-10 transition-metal dichalcogenides (TMDs), especially palladium diselenide (PdSe2), are promising candidates for polarized photodetection due to their low-symmetric crystal structure. However, the lack of an efficient heterostructure severely restricts their applications in UV-polarized photodetection. Here, we develop a PdSe2/GaN Schottky junction by in situ van der Waals growth for highly polarization-sensitive UV photodetection. Owing to the high-quality junction, the device exhibits an appealing UV detection performance in terms of a large responsivity of 249.9 mA/W, a high specific detectivity, and a fast response speed. More importantly, thanks to the puckered structure of the PdSe2 layer, the device is highly sensitive to polarized UV light with a large dichroic ratio up to 4.5, which is among the highest for 2D TMD material-based UV polarization-sensitive photodetectors. These findings further enable the demonstration of the outstanding polarized UV imaging capability of the Schottky junction, as well as its utility as an optical receiver for secure UV optical communication. Our work offers a strategy to fabricate the PdSe2-based heterostructure for high-performance polarization-sensitive UV photodetection.