Quantifying the Hydrophobic Effect per CF2 Moiety from Adsorption of Fluorinated Alcohols at the Water/Oil Interface.

Amphiphilic fluorocarbon substances are a trending topic of research due to their wide range of applications accompanied by an alarming environmental and health impact. In order to predict their fate in the environment, use them more economically, develop new water treatment methods, etc., a better understanding of their physicochemical behavior is required. Their hydrophobicity in water/oil systems is particularly sensitive to one key thermodynamic parameter: the free energy of transfer of a perfluoromethylene group from oil to water. However, for the -CF2- moiety, the transfer energy values reported in the literature vary by more than ±25%. Due to the exponential relationship between this energy and the adsorption constants or the partition coefficients, such an uncertainty can lead to orders of magnitude error in the predicted distribution of fluorinated species. We address this problem by presenting an experimental determination of the hydrophobic effect of a -CF2- moiety with a greater certainty than currently available. The transfer energy is determined by measuring the interfacial tension of water|hexane for aqueous solutions of short-chained fluorotelomer alcohols. The obtained results for the free energy of transfer of a -CF2- moiety from oil to water are 1.68±0.02×RT0, 1.75±0.02×RT0, and 1.88±0.02×RT0 at 288.15 K, 293.15 K, and 303.15 K, respectively.

Predictive scaling of fiber-based protein A capture chromatography using mechanistic modeling.

Protein A affinity chromatography is an important step in the purification of monoclonal antibodies (mAbs) and mAb-derived biotherapeutics. While the biopharma industry has extensive expertise in the operation of protein A chromatography, the mechanistic understanding of the adsorption/desorption processes is still limited, and scaling up and scaling down can be challenging because of complex mass transfer effects in bead-based resins. In convective media, such as fiber-based technologies, complex mass transfer effects such as film and pore diffusions do not occur which facilitates the study of the adsorption phenomena in more detail and simplifies the process scale-up. In the present study, the experimentation with small-scale fiber-based protein A affinity adsorber units using different flow rates forms the basis for modeling of mAb adsorption and elution behavior. The modeling approach combines aspects of both stoichiometric and colloidal adsorption models, and an empirical part for the pH. With this type of model, it was possible to describe the experimental chromatograms on a small scale very well. An in silico scale-up could be carried out solely with the help of system and device characterization without feedstock. The adsorption model could be transferred without adaption. Although only a limited number of runs were used for modeling, the predictions of up to 37 times larger units were accurate.

The Use of the Statistical Entropy in Some New Approaches for the Description of Biosystems.

Some problems of describing biological systems with the use of entropy as a measure of the complexity of these systems are considered. Entropy is studied both for the organism as a whole and for its parts down to the molecular level. Correlation of actions of various parts of the whole organism, intercellular interactions and control, as well as cooperativity on the microlevel lead to a more complex structure and lower statistical entropy. For a multicellular organism, entropy is much lower than entropy for the same mass of a colony of unicellular organisms. Cooperativity always reduces the entropy of the system; a simple example of ligand binding to a macromolecule carrying two reaction centers shows how entropy is consistent with the ambiguity of the result in the Bernoulli test scheme. Particular attention is paid to the qualitative and quantitative relationship between the entropy of the system and the cooperativity of ligand binding to macromolecules. A kinetic model of metabolism. corresponding to Schrödinger's concept of the maintenance biosystems by "negentropy feeding", is proposed. This model allows calculating the nonequilibrium local entropy and comparing it with the local equilibrium entropy inherent in non-living matter.

Pore size dependent molecular adsorption of cationic dye in biomass derived hierarchically porous carbon.

Hierarchically porous carbon adsorbents were successfully fabricated from different biomass resources (softwood, hardwood, bamboo and cotton) by a facile two-step process, i.e. carbonization in nitrogen and thermal oxidation in air. Without involving any toxic/corrosive chemicals, large surface area of up to 890 m2/g was achieved, which is comparable to commercial activated carbon. The porous carbons with various surface area and pore size were used as adsorbents to investigate the pore size dependent adsorption phenomenon. Based on the density functional theory, effective (E-SSA) and ineffective surface area (InE-SSA) was calculated considering the geometry of used probing adsorbate. It was demonstrated that the adsorption capacity strongly depends on E-SSA instead of total surface area. Moreover, a regression model was developed to quantify the adsorption capacities contributed from E-SSA and InE-SSA, respectively. The applicability of this model has been verified by satisfactory prediction results on porous carbons prepared in this work as well as commercial activated carbon. Revealing the pore size dependent adsorption behavior in these biomass derived porous carbon adsorbents will help to design more effective materials (either from biomass or other carbon resources) targeting to specific adsorption applications.

Modelling the pH dependent retention and competitive adsorption of charged and ionizable solutes in mixed-mode and reversed-phase liquid chromatography.

This study investigated the influence of pH on the retention of solutes using a mixed-mode column with carboxyl (-COOH) groups acting as weak cation exchanger bonded to the terminal of C18 ligands (C18-WCX column) and a traditional reversed-phase C18 column. First, a model based on electrostatic theory was derived and successfully used to predict the retention of charged solutes (charged, and ionizable) as a function of mobile phase pH on a C18-WCX column. While the Horváth model predicts the pH-dependent retention of ionizable solutes in reversed-phase liquid chromatography (RPLC) solely based on solute ionization, the developed model incorporates the concept of surface potential generated on the surface of the stationary phase and its variation with pH. To comprehensively understand the adsorption process, adsorption isotherms for these solutes were individually acquired on the C18-WCX and reversed-phase C18 columns. The adsorption isotherms followed the Langmuir model for the uncharged solute and the electrostatically modified Langmuir model for charged solutes. The elution profiles for the single components were calculated from these isotherms using the equilibrium dispersion column model and were found to be in close agreement with the experimental elution profiles. To enable modelling of two-component cases involving charged solute(s), a competitive adsorption isotherm model based on electrostatic theory was derived. This model was later successfully used to calculate the elution profiles of two components for scenarios involving (a) a C18 Column: two charged solutes, (b) a C18 Column: one charged and one uncharged solute, and (c) a C18-WCX Column: two charged solutes. The strong alignment between the experimental and calculated elution profiles in all three scenarios validated the developed competitive adsorption model.

Investigation of the mucin-nanoparticle interactions via real-time monitoring by microbalance and kinetic model simulation.

Interactions between nanoparticles and the mucus layer are crucial to understand the behaviours in biological environments and design drug delivery systems. In this study, we developed a kinetic deposition model for the dynamic mucin-nanoparticle interactions using quartz crystal microbalance with dissipation (QCM-D). We investigated the effects of the physiochemical properties of several nanoparticles (including size, charge, and shape) and the physiological conditions on the mucin-nanoparticle interaction. Interestingly, layered double hydroxide (LDH) nanoparticles showed stronger interactions with the mucus layer compared to other types of nanoparticles due to their unique plate-like morphology. In specific for sheet-like LDH nanoparticles, our model found that their equilibrium adsorption capacity (Qe) followed the Langmuir adsorption isotherm, and the adsorption rate (k1) increased proportionally with the nanoparticle concentration. In addition, the particle size and thickness affected Qe and the surface coverage. Furthermore, bovine serum albumin (BSA) coating dramatically increased k1 of LDH nanoparticles. We proposed a novel mechanism to elucidate mucin-nanoparticle interactions, shedding light on the synergistic roles of drag force (Fd), repulsive force (Fr), and adsorptive force (Fa). These findings offer valuable insights into the complex mucin-nanoparticle interactions and provide guidance for the design of drug delivery systems.

Competitive adsorption of Cd(II), Zn(II) and Ni(II) from their binary and ternary acidic systems using tourmaline.

The adsorption of Cd(II), Zn(II) and Ni(II) from aqueous solutions in binary and ternary component systems by tourmaline was investigated. Kinetic data were accurately fitted to pseudo-second order and internal diffusion models, which indicated that the adsorption of heavy metals occurred on the interior surface of the sorbent and internal diffusion was the controlling mechanism during heavy metal ion adsorption but was not the only rate-controlling step. Additionally, tourmaline had a very good adsorption capacity for Cd(II), Zn(II) and Ni(II) in multi-component aqueous solutions at strongly acidic pH values (in contrast to industrial wastewater pH values). This good adsorption capacity is attributed to the fact that tourmaline can automatically adjust the pH values of acidic (except pH 2.0 and 3.0), neutral or alkaline aqueous solutions to 6.0. Adsorption isotherms and separation factors showed that tourmaline displays a high selectivity toward one metal in a two-component or a three-component system with an affinity order of Cd(II) > Zn(II) > Ni(II). Thermodynamic parameters indicated that heavy metal adsorption was feasible, spontaneous, and endothermic. Therefore, tourmaline should be explored as a material for removing pollutants from the strongly acidic wastewater.

The model and mechanism of adsorptive technologies for wastewater containing fluoride: A review.

With the continuous development of society, industrialization, and human activities have been producing more and more pollutants. Fluoride discharge is one of the main causes of water pollution. This review summarizes various commonly used and effective fluoride removal technologies, including ion exchange technology, electrochemical technology, coagulation technology, membrane treatment, and adsorption technology, and points out the outstanding advantages of adsorption technology. Various commonly used fluoride removal techniques as well as typical adsorbent materials have been discussed in published papers, however, the relationship between different adsorbent materials and adsorption models has rarely been explored, therefore, this paper categorizes and summarizes the various models involved in static adsorption, dynamic adsorption, and electrosorption fluoride removal processes, such as pseudo-first-order and pseudo-second-order kinetic models, Langmuir and Freundlich isotherm models, Thomas and Clark dynamic adsorption models, including the mathematical equations of the corresponding models and the significance of the models are also comprehensively summarized. Furthermore, this comprehensive discussion delves into the fundamental adsorption mechanisms, quantification of maximum adsorption capacity, evaluation of resistance to anion interference, and assessment of adsorption regeneration performance exhibited by diverse adsorption materials. The selection of the best adsorption model not only predicts the adsorption performance of the adsorbent but also provides a better description and understanding of the details of each part of the adsorption process, which facilitates the adjustment of experimental conditions to optimize the adsorption process. This review may provide some guidance for the development of more cost-effective adsorbent materials and adsorption processes in the future.

Quantitative characterizations of mOR-EG activated by vanilla odorants using advanced statistical physics modeling.

An advanced monolayer adsorption model of an ideal gas was successfully employed to investigate the adsorption of vanillin, vanillin methyl ether, vanillin ethyl ether, and vanillin acetate odorants on mouse eugenol olfactory receptor mOR-EG. In order to understand the adsorption process putatively introduced in olfactory perception, model parameters were analyzed. Hence, fitting results showed that the studied vanilla odorants were linked in mOR-EG binding pockets with a non-parallel orientation, and their adsorption was a multi-molecular process (n > 1). The adsorption energy values that ranged from 14.021 to 19.193 kJ/mol suggested that the four vanilla odorants were physisorbed on mOR-EG (ΔEa < 40 kJ/mol) and the adsorption mechanism may be considered as an exothermic mechanism (ΔEa > 0). The estimated parameters may also be utilized for the quantitative characterization of the interactions of the studied odorants with mOR-EG to determine the corresponding olfactory bands ranging from 8 to 24.5 kJ/mol.

Heterogenous adsorption mechanisms for describing enantioselective retention in normal-phase liquid chromatography.

In this study, the enantioselective retention behaviors of methyl mandelate (MM) and benzoin (B) were investigated using Chiralpak IB as a sorbent and ethanol, 1-propanol, and 1-butanol as solvent modifiers in the normal-phase mode. For both MM and B, similar chiral recognition mechanisms were observed, potentially involving at least two types of chiral adsorption sites. With a retention model describing local retention behaviors, an enantioselectivity model based on a three-site model was proposed to describe the data. Fitted parameters were also used to analyze the contributions of each type of adsorption site to the apparent retention behavior. Combining the local retention model with the three-site model provided a qualitative and quantitative explanation for the correlation between modifier concentration and enantioselectivity. Overall, our results indicated that heterogeneous adsorption mechanisms are a key aspect in understanding enantioselective retention behaviors. Distinct local adsorption sites contribute differently to apparent retention behaviors, with these contributions being influenced by the mobile phase composition to varying degrees. Hence, enantioselectivity changes with variations in modifier concentration.

Determination of catechol in water with deep eutectic supramolecular solvents-assisted magnetic κ-carrageenan nanoparticles.

A combination of magnetic κ-carrageenan nanoparticles and deep eutectic supramolecular solvents used for extraction of catechol from water was evaluated by the magnetic dispersion solid phase extraction method. The magnetic κ-carrageenan nanoparticles (KC@Fe3O4MNPs) and the deep eutectic supramolecular solvent (DESP) were characterised by 1H NMR, FT-IR, XRD, SEM, VSM, TG, and BET. The adsorption kinetics, adsorption isothermal model, adsorption thermodynamics and effects of pH and salt concentration were investigated. Additionally, the factors used in the desorption process, such as the type, dosage, concentration and time, were analysed. Under the optimised conditions, the analytes were linear over the range 5-5000 ng mL-1, with a correlation coefficient greater than 0.999 and detection and quantitation limits of 1.6 and 4.7 ng mL-1, respectively. The procedure was successfully applied to determinations of the analytes of interest in spiked water samples with relative average recoveries ranging from 94.3% to 101.5%. These results indicated that the combination of functionalized magnetic nanoparticles and DESP had high specificity and extraction efficiency for catechol and will be a feasible alternative to conventional analyses of organic phenolic pollutants in water.

Coloration Modeling and Processing of Commodity Plastic Buttons in Supercritical Carbon Dioxide.

We examined the color processing of the commodity plastic buttons made of acrylic, polyester, nylon, and casein with scCO2. The buttons' dyeing color depth (K/S) was measured over a wide range of scCO2 and correlated accurately with the response surface method. Moreover, we measured the solubility of C.I. Disperse Red 22 in scCO2 to formulate a dye-sorption model for the K/S value in the color processing of the plastic buttons. Finally, the dye-sorption model for the K/S value combining the dye solubility in scCO2 with the dye diffusion inside the buttons successfully represented the color processing of the buttons.

Adsorption of l-buthionine sulfoximine on Bi(III) and Eu(III) co-substituted hydroxyapatite nanocrystals for enhancing radiosensitization effects.

Cancer theranostics combines therapeutic and diagnostic capabilities into a single system to treat cancer efficiently. Biocompatible nanomaterials can be engineered to exhibit cancer theranostic functions, for instance radiosensitization and photoluminescence. In this study, trivalent Bi and Eu ions were co-substituted into the lattice of hydroxyapatite (Bi(III):Eu(III) HAp) to develop a cancer theranostic nanocrystal. Bi provides radiosensitization capabilities while Eu imparts photoluminescence properties. To complement the radiotherapeutic function, l-buthionine sulfoximine (l-BSO) was adsorbed onto the nanocrystal surface. l-BSO inhibits the biosynthesis of cellular antioxidants, which can enhance radiosensitization effects. The Bi(III):Eu(III) HAp nanocrystals were prepared via a hydrothermal method. Structural and compositional analyses showed that both Bi and Eu ions were substituted into the HAp lattice. l-BSO was adsorbed onto the surface via electrostatic interactions between the charged carboxyl and amino groups of l-BSO and the surface ions of the nanocrystals. The adsorption followed the Langmuir isotherm model, implying a homogeneous monolayer adsorption. The l-BSO adsorbed Bi(III):Eu(III) HAp nanocrystals were found to have negligible cytotoxicity except the setting with l-BSO adsorbed amounts of 0.44 µmol/m2. This l-BSO amount was found to be high enough to elicit cytotoxicity due to l-BSO being released and causing excessive antioxidant depletion. Gamma ray irradiation clearly activated the cytotoxicity of the samples and increased the cell death rate, confirming radiosensitization abilities. At a constant amount of nanocrystals, the cell death rate increases with l-BSO concentration. This indicates that l-BSO can enhance the radiosensitization effect of the Bi(III):Eu(III) HAp nanocrystals.

Removal of Typical PPCPs by Reverse Osmosis Membranes: Optimization of Treatment Process by Factorial Design.

In this paper, the removal effect of reverse osmosis (RO) on three common pharmaceuticals and personal care products (PPCPs), including ibuprofen (IBU), carbamazepine (CBZ), and triclosan (TCS), were compared under different process conditions, and the removal rate of PPCPs, membrane flux, and PPCPs membrane adsorption capacity were analyzed. The removal rate increased with the increase of the influent concentration and pre-membrane pressure, while pH influenced the removal effect of different PPCPs by affecting the electrostatic interaction between pollutants and membranes. It was also found that the dynamic adsorption of PPCPs on RO membranes under different conditions complied with the pseudo-first-order reaction kinetic adsorption model. The maximum stable adsorption capacity and the adsorption rate of PPCPs on membranes under various conditions were simulated based on the model. Moreover, through factorial design, the removal rates of RO on IBU, CBZ, and TCS could reach 98.93%, 97.47%, and 99.01%, respectively, under the optimal conditions (with an influent concentration of 500 µg/L, pre-membrane pressure of 16 bar and pH = 10). By optimizing the process of removing PPCPs with the RO membrane method, the optimal process conditions of removing IBU, CBZ, and TCS with the RO membrane method were obtained, which provided reference conditions and data support for the practical application of removing PPCPs with the RO membrane method.

Complete defluorination of perfluorooctanoic acid (PFOA) by ultrasonic pyrolysis towards zero fluoro-pollution.

Advanced oxidation/reduction of PFAS is challenged and concerned by the formation of toxic, short-chain intermediates during water treatments. In this study, we investigated the complete defluorination of PFOA by ultrasound/persulfate (US/PS) with harmless end-products of CO2, H2O, and F‒ ions. We observed 100% defluorination after 4 h of US treatment alone with a power input of 900 W. PS addition, however, suppressed defluorination. We demonstrated by kinetics-fitted Langmuir-type adsorption modeling, the added PS increased competition with PFOA for adsorption sites on the bubble-water interface where radical oxidation and pyrolysis may occur. Providing sulfate (SO4•-) and hydroxyl (•OH) radicals by means other than US did not defluorinate PFOA, indicating that pyrolysis likely contributes to the high defluorination performance. Bond dissociation energies for CC and CF were independent of pressure but decreased at elevated temperatures within cavitation bubbles (i.e., 5000 K) favoring the pyrolysis reactions. Furthermore, bond length calculations indicated that PFOA cleavage only begins to occur at temperatures in excess of those generated at the bubble interface (i.e., >1500 K) at the femtosecond level. This suggests that PFOA vaporizes or injects by nanodrops upon attachment to the cavitation bubble, enters the bubble, and is then cleaved within the bubble by pyrolysis. Our research in low-frequency ultrasonic horn system challenges the previous founding that defluorination of PFOA initiates and occurs at the bubble-water interface. We describe here that supplementing US-based processes with complementary treatments may have undesired effects on the efficacy of US. The mechanistic insights will further promote the implementation of US technology for PFAS treatment in achieving the zero fluoro-pollution goal.

Mechanistic modeling, simulation, and optimization of mixed-mode chromatography for an antibody polishing step.

Mixed-mode chromatography combines features of ion-exchange chromatography and hydrophobic interaction chromatography and is increasingly used in antibody purification. As a replacement for flow-through operations on traditional unmixed resins or as a pH-controlled bind-and-elute step, the use of both interaction modes promises a better removal of product-specific impurities. However, the combination of the functionalities makes industrial process development significantly more complex, in particular the identification of the often small elution window that delivers the desired selectivity. Mechanistic modeling has proven that even difficult separation problems can be solved in a computer-optimized manner once the process dynamics have been modeled. The adsorption models described in the literature are also very complex, which makes model calibration difficult. In this work, we approach this problem with a newly constructed model that describes the adsorber saturation with the help of the surface coverage function of the colloidal particle adsorption model for ion-exchange chromatography. In a case study, a model for a pH-controlled antibody polishing step was created from six experiments. The behavior of fragments, aggregates, and host cell proteins was described with the help of offline analysis. After in silico optimization, a validation experiment confirmed an improved process performance in comparison to the historical process set point. In addition to these good results, the work also shows that the high dynamics of mixed-mode chromatography can produce unexpected results if process parameters deviate too far from tried and tested conditions.

A critical and recent developments on adsorption technique for removal of heavy metals from wastewater-A review.

This review provides a quantitative description of the nano-adsorbent processing and its viability against wastewater detoxification by extracting heavy metal ions. The impact of nano-adsorbent functionalities on specific essential attributes such as the surface area, segregation, and adsorption capacity were comprehensively evaluated. A detailed analysis has been presented on the characteristics of nanomaterials through their limited resistance to adsorb some heavy metal ions. Experimental variables such as the adsorbent dosage, pH, substrate concentration, response duration, temperature, and electrostatic force that influence the uptake of metal ions have been studied. Besides, separate models for the adsorption kinetics and isothermal adsorption have been investigated to understand the mechanism behind adsorption. Here, we reviewed the different adsorbent materials with nano-based techniques for the removal of heavy metals from wastewater and especially highlighted the nano adsorption technique. The influencing factors such as pH, temperature, dosage time, sorbent dosage, adsorption capacities, ion concentration, and mechanisms related to the removal of heavy metals by nano composites are highlighted. Lastly, the application potentials and challenges of nano adsorption for environmental remediation are discussed. This critical review would benefit engineers, chemists, and environmental scientists involved in the utilization of nanomaterials for wastewater treatment.

Tetracycline adsorption trajectories on aged polystyrene in a simulated aquatic environment: A mechanistic investigation.

Microplastics (MPs) have attracted widespread attention as an organic class of pollutants as well as pollutant carriers in recipient aquatic ecosystems. In this study, tetracycline (TC) adsorption by polystyrene (PS), with multiple aging-based temporal changes in the adsorption mechanism, was observed. The results revealed that the pseudo-second-order model accurately predicted the TC adsorption kinetics for different types of PS. In addition, the isothermal adsorption processes fit the Freundlich model; however, their interactions were drastically weakened at lower temperatures or increasing salinities. Corresponding to the electrostatic interactions, adsorption TC was largely pH-dependent, with the maximum adsorbed TC content on the PS surface at a pH of 5 in an aqueous environment. More importantly, mechanistic studies have revealed that, compared to virgin PS, TC complexes with aged PS are principally controlled by hydrogen bonding and ionic interactions, followed by π-π, polar-polar, and van der Waals interactions. These findings will aid in understanding the insights of TC and aged PS interactions and the underlying interactive molecular forces, which will be advantageous for comprehending the real case scenario of inter-pollutant interactions and related environmental pollution.

Adsorption behavior of biochar pyrolyzed from barracuda grass for cadmium ions.

This work investigated the removal of cadmium ions (Cd2+) by using biochar derived from Barracuda Grass. The biochars derived from the pyrolysis of roots (BGR), stems (BGS) and leaves (BGL) were characterized and their performance for cadmium adsorption was studied at varying parameters of temperature, time, and alkali (earth) metal concentrations. The maximum adsorption amount at equilibrium of BGR, BGS and BGL was determined experimentally as 8.38 mg/g, 42.12 mg/g, and 30.39 mg/g. Adsorption fitting results revealed that Cd2+ adsorbed on BGR and BGS preferred to be multilayer-covered, and BGL was more likely to have monolayer-covered functions. The kinetic data fitted well to the pseudo-second-order model (R 2 > 0.99), revealing the adsorption process was a spontaneous monolayer chemisorption process. The results of alkaline (earth) metals leaching of biochar revealed that the inherent alkaline (earth) metals in biochar made inhibitory functions on the Cd2+ adsorption behavior by occupying the active sites. And in the process of wastewater treatment, the leaching of alkaline earth metals might enhance the complexation reaction between surface groups and Cd2+. This study provides a feasible strategy for the resource utilization of abundant hydrophytic plants in waste management.

The influence of electrolytes in the adsorption kinetics of reactive BF-5G blue dye on bone char: a mass transfer model.

The discharge of harmful dyes in water bodies is a serious pollution problem, dangerous for the ecosystem's equilibrium and human health. In this sense, the aim of this work was to determine the influence of electrolytes (NaCl, KCl, CaCl2 and MgCl2) in the adsorption of Reactive Blue BF-5G dye, the most common dye used in industrial process for fabric colouring, using bovine bone char as the adsorbent. The bovine bone char was characterized by pH of point of zero charge (pHPZC), N2 adsorption-desorption isotherms, Fourier transform-infrared spectroscopy (FT-IR) and X-ray diffractometry (XDR). The characterization revealed a mesoporous structure (pore mean diameter of 94 Šand SBET ∼107 m2 g-1) with negative charge distribution at the surface (pHPZC = 3.8). The adsorption experiments revealed that the presence of KCl enhanced the material adsorption capacity (qmax = 195 mg g-1), that the Sips isotherm best fitted the experimental data (R2 > 0.9 except for KCl solution) and the adsorption process was mono- and multilayered. The kinetic adsorption experiments indicated that the inorganic electrolytes increased the initial adsorption velocity and the data was best modelled by the surface diffusional model (SDM), implying a resistance (aqueous > CaCl2 > NaCl > MgCl2 > KCl) to mass transfer at the surface of the pores which, in turn, prevented the dye diffusion to the interior of the adsorbent (qe = 71 mg g-1). Therefore, small quantities of KCl can be used to lower the mass transfer resistance and provide higher adsorption capacity with reduced time of operation, thus increasing the overall process efficiency.