Mouldable Conductive Plastic with Optimised Mechanical Properties.

This paper investigates making an injection mouldable conductive plastic formulation that aims for conductivity into the electromagnetic interference (EMI) shielding range, with good mechanical properties (i.e., stiffness, strength, and impact resistance). While conductivity in the range (electrostatic charge dissipation) and EMI shielding have been attained by incorporating conductive fillers such as carbon black, metals powders, and new materials, such as carbon nanotubes (CNTs), this often occurs with a drop in tensile strength, elongation-to-break resistance, and impact resistance. It is most often the case that the incorporation of high modulus fillers leads to an increase in modulus but a drop in strength and impact resistance. In this work, we have used short carbon fibres as the conductive filler and selected a 50/50 PBT/rPET (recycled PET) for the plastic matrix. Carbon fibres are cheaper than CNTs and graphenes. The PBT/rPET has low melt viscosity and crystallises sufficiently fast during injection moulding. To improve impact resistance, a styrene-ethylene-butadiene-styrene (SEBS) rubber toughening agent was added to the plastic. The PBT/rPET had very low-impact resistance and the SEBS provided rubber toughening to it; however, the rubber caused a drop in the tensile modulus and strength. The short carbon fibre restored the modulus and strength, which reached higher value than the PBT/rPET while providing the conductivity. Scanning electron microscope pictures showed quite good bonding of the current filler (CF) to the PBT/rPET. An injection mouldable conductive plastic with high conductivity and raised modulus, strength, and impact resistance could be made.

Multi-electrode platform for selective electrochemical sensing: 3D-printed insulating plastic is turned into a five-electrodes chip.

We report a method to turn a 3D-printed plastic piece into a five-electrodes chip for multiple analytes detection. A chip containing Pd, Ni, and Ru working electrodes is used to sense hydroquinone, acetaminophen, salicylic acid, and hydroxychloroquine at once. The analysis is sequentially achieved simply by changing the proper electrode connection, without changing mobile parts, neither adding reactants, nor electrolytes. This strategy is an alternative for low-cost selective electrochemical detection.

Electrically-Responsive Reversible Polyketone/MWCNT Network through Diels-Alder Chemistry.

This study examines the preparation of electrically conductive polymer networks based on furan-functionalised polyketone (PK-Fu) doped with multi-walled carbon nanotubes (MWCNTs) and reversibly crosslinked with bis-maleimide (B-Ma) via Diels-Alder (DA) cycloaddition. Notably, the incorporation of 5 wt.% of MWCNTs results in an increased modulus of the material, and makes it thermally and electrically conductive. Analysis by X-ray photoelectron spectroscopy indicates that MWCNTs, due to their diene/dienophile character, covalently interact with the matrix via DA reaction, leading to effective interfacial adhesion between the components. Raman spectroscopy points to a more effective graphitic ordering of MWCNTs after reaction with PK-Fu and B-Ma. After crosslinking the obtained composite via the DA reaction, the softening point (tan(δ) in dynamic mechanical analysis measurements) increases up to 155 °C, as compared to the value of 130 °C for the PK-Fu crosslinked with B-Ma and that of 140 °C for the PK-Fu/B-Ma/MWCNT nanocomposite before resistive heating (responsible for crosslinking). After grinding the composite, compression moulding (150 °C/40 bar) activates the retro-DA process that disrupts the network, allowing it to be reshaped as a thermoplastic. A subsequent process of annealing via resistive heating demonstrates the possibility of reconnecting the decoupled DA linkages, thus providing the PK networks with the same thermal, mechanical, and electrical properties as the crosslinked pristine systems.