Comparative responses of flocculating and nonflocculating yeasts to cell density and chemical stress in lactic acid fermentation.

While flocculation has demonstrated its efficacy in enhancing yeast robustness and ethanol production, its potential application for lactic acid fermentation remains largely unexplored. Our study examined the differences between flocculating and nonflocculating Saccharomyces cerevisiae strains in terms of their metabolic dynamics when incorporating an exogenous lactic acid pathway, across varying cell densities and in the presence of lignocellulose-derived byproducts. Comparative gene expression profiles revealed that cultivating a nonflocculant strain at higher cell density yielded a substantial upregulation of genes associated with glycolysis, energy metabolism, and other key pathways, resulting in elevated levels of fermentation products. Meanwhile, the flocculating strain displayed an inherent ability to sustain high glycolytic activity regardless of the cell density. Moreover, our investigation revealed a significant reduction in glycolytic activity under chemical stress, potentially attributable to diminished ATP supply during the energy investment phase. Conversely, the formation of flocs in the flocculating strain conferred protection against toxic chemicals present in the medium, fostering more stable lactic acid production levels. Additionally, the distinct flocculation traits observed between the two examined strains may be attributed to variations in the nucleotide sequences of the flocculin genes and their regulators. This study uncovers the potential of flocculation for enhanced lactic acid production in yeast, offering insights into metabolic mechanisms and potential gene targets for strain improvement.

Concentration of clarified pool by single-pass tangential flow filtration to improve productivity of protein A capture step: Impact of clarification strategies.

Protein A capture chromatography remains a high-cost and relatively low-productivity step for downstream processing of monoclonal antibodies. As bioprocessing transitions toward intensified processes, maximizing the efficiency of individual steps is key to achieving economic targets. This study was performed to assess the impact of inline concentration of clarified cell culture fluid (CCF), using single-pass tangential flow filtration, on protein A chromatography purification productivity. CCF with varying levels of impurities and turbidity were obtained dependent upon the clarification method. These CCFs were concentrated and processed over a protein A capture step. Productivity increases of 1.8- to 2.6-fold were achieved as compared to a protein A capture step with no CCF concentration. Achieving such targeted improvements requires careful consideration of the multiple components in the clarification strategy before implementation.

Biodesulfurization of landfill biogas by a pilot-scale bioscrubber: Operational limits and microbial analysis.

Biogas serves as a crucial renewable energy vector to ensure a more sustainable energy future. However, the presence of hydrogen sulfide (H2S) limits its application in various sectors, emphasizing the importance of effective H2S removal techniques for maximizing its potential. In the present study, the limits of a pilot-scale bioscrubber for biogas desulfurization was study in a real scenario. An increase in the superficial liquid velocity resulted in significant improvements in the H2S removal efficiency, increasing from 76 ± 8% (elimination capacity of 6.2 ± 0.5 gS-H2S m-3 h-1) to 97.7 ± 0.5% (elimination capacity of 8 ± 1 gS-H2S m-3 h-1) as the superficial liquid velocity increased from 50 ± 3 m h-1 to 200 ± 8 m h-1. A USL of 161.4 ± 0.5 m h-1 was able to achieve outlet H2S concentrations as low as 3 ± 1 ppmv (H2S removal efficiency of 97 ± 1%) for 7 days. High superficial liquid velocity favoured the aerobic H2S oxidation reducing the nitrate demand. The maximum EC reached throughout the operation was 50.8 ± 0.6 gS-H2S m-3 h-1 (H2S removal efficiency of 96 ± 1%) and a sulfur production of 60%. Studies in batch flocculation experiments showed sulfur removal rates up to 97.6 ± 0.9% with a cationic flocculant dose of 75 mg L-1. Microbial analysis revealed that the predominant genus with sulfo-oxidant capacity during periods of low H2S inlet load was Thioalkalispira-sulfurivermis (61-69%), while in periods of higher H2S inlet load, family Arcobacteraceae was the most prevalent (11%).

Analysing the role of Fe (II) on flocculation of sand-clay mixtures under estuarine mixing.

Estuaries are fragile environment that are most affected by climate change. One of the major consequences of climate change on estuarine processes is the enhancement in salt intrusion leading to higher salinity values. This has several implications on the estuarine sediment dynamics. Of the various factors that affect the flocculation of cohesive sediments, salinity and turbulence have been recognized as to have great significance. Many of the estuaries are contaminated with heavy metals, of which, the concentration of Iron (Fe (II)) are generally on the higher range. However, the influence of Fe (II) on the flocculation of cohesive sediments at various estuarine mixing conditions is not well known. The present study investigated the influence of Fe (II) on the flocculation of kaolin at various concentration of Fe (II), salinity and turbulence shear. The results indicated that Fe (II) and salinity have a positive influence on kaolin flocculation. The increase in turbulence shear caused an initial increase and then a decrease in floc size. In case of sand-clay mixtures, that are observed in mixed sediment estuarine environments, a reduction in the floc size was observed, which is attributed to the breakage of flocs induced by the shear of sand. Breakage coefficient, which is a measure of break-up of flocs, is generally adopted as 0.5 assuming binary breakage. The present study revealed that the breakage coefficient can take values from 0 to 1 and is a direct function of Fe (II) and salinity and an inverse function of turbulence and sand concentration. Thus, a new model for breakage coefficient with the influencing parameters has been proposed, which is an improvement of existing model that is expressed in terms of turbulence alone. Sensitivity analysis showed that the proposed model can very well predict the breakage coefficient of Fe (II) - kaolin flocs. Thus, the model can quantify the breakage coefficient of flocs in estuaries contaminated with Fe (II) that is a vital parameter for population balance models.

Inhibiting effects of humic acid on iron flocculation hindered As removal by electro-flocculation on air cathode iron anode.

Activated carbon air cathode combined with iron anode oxidation-flocculation synergistic Arsenic (As) removal was a new groundwater purification technology with low energy consumption and high efficiency for groundwater with high As concentration. The presence of organic matter such as humic acid (HA) had ambiguous effects on formation of organic colloids in the system. The effects of the particle size distribution characteristics of these colloids on the formation characteristics of flocs and the efficiency of As purification was not clear. In this work, we used five different pore size alumina filter membranes to separate mixed phase solutions and studied the corresponding changes in iron and arsenic concentrations in the presence and absence of humic acid conditions. In the presence of HA, the arsenic concentration of < 0.05 µm particle size components was 1.01, 1.28, 3.07, 7.69, 2.85 and 1.24 times of that in the absence of HA. At the same time, the arsenic content in 0.05-0.1 µm and 0.1-0.45 µm particle size components was also higher than that in the system without HA, which revealed that the presence of HA hindered the flocculation behavior of As distribution to higher particle sizes in the early stage of the reaction. The presence of HA affected the flocculation rate of iron flocs from small to large particle size fractions and it had limited effect on the behavior of large-size flocs in adsorption of As. These results provide a theoretical basis for targeted, rapid, and low consumption synergistic removal of arsenic and organic compounds in high arsenic groundwater.

Concentrated Deoiled Fat: A Novel Method of Fat Processing to Improve Fat Graft Survival-A Basic Research.

BACKGROUND: Oil compromises graft outcomes via inflammation, which accounts for the unpredictability of volume retention rates as low as 20%. Existing techniques for oil removal are relatively inefficient. In this study, a novel approach was taken to prepare concentrated deoiled fat (CDF) by utilizing flocculation and centrifugation to remove the oil. The hypothesis put forward in this study was that CDF would exhibit improved volume retention and quality by enhancing purification efficiency and reducing inflammation. METHODS: This basic research involved both in vitro and in vivo experiments using samples obtained from women who underwent abdominal liposuction. The CDF was prepared by flocculation and centrifugation. In the vitro experiments, the microstructure of fat was assessed using Calcein acetoxymethyl ester (AM) staining for living cells and propidium iodide (PI) staining for dead nuclei in two groups: Coleman fat group and CDF group. Additionally, the glucose uptake capacity of these two groups was evaluated using the glucose transport test (GTT). In the vivo experiments, the study included three groups: two experimental groups (low-volume concentrated deoiled fat, LCDF; high-volume concentrated deoiled fat, HCDF) and one control group (Coleman fat), with 10 healthy female BALB/c nude mice in each group, 1ml of the graft was injected subcutaneously to each mouse. After 8 weeks, the fat grafts were harvested and subjected to volume evaluation, HE staining and immunostaining for perilipin to assess graft outcomes. RESULTS: In the vitro experiments, the concentration rate of the CDF was found to be 79.6% that of Coleman fat, with 15.1% more oil separated. Cell viability, as assessed by AM/PI staining, did not show a significant difference between the two grafts, but the results of the GTT showed that the tissue viability of the CDF was higher than that of Coleman fat. In the vivo experiments, the CDF had higher volume retention than Coleman fat, as measured by water displacement. Histopathologic scoring indicated that HCDF group and LCDF group had a more intact fat structure with fewer vacuoles, inflammation, and fibrosis compared to Coleman fat. Additionally, the percentages of perilipin-positive area in the LCDF group and HCDF group were higher than in the Coleman group, indicating improved graft quality and outcome with the use of concentrated deoiled fat. CONCLUSIONS: "Concentrated deoiled fat" refers to an autologous fat graft from which oil has been removed by flocculation and centrifugation. This process increases volume retention and viable cells and decreases infiltrated inflammatory cells. LEVEL OF EVIDENCE V: This journal requires that authors assign a level of evidence to each article. For a full description of these Evidence-Based Medicine ratings, please refer to the Table of Contents or the online Instructions to Authors   www.springer.com/00266 .

Potential of ash from agricultural waste as substitute of commercial FeCl3 in primary treatment of landfill leachate.

Due to the ever increasing global population, higher volumes of industrial waste discharges to landfill have caused major problems for the environment. This study investigated the performance of rice straw ash (RSA) as a natural coagulant under different conditions for the treatment of landfill leachates by coagulation-flocculation and microfiltration, with and without addition of FeCl3. The highest performing treatment conditions (RSA = 2.48 g/L, FeCl3 = 4.98 g/L, settling time = 54.75min) were achieved with the combined use of RSA and FeCl3 as coagulant and led to a sludge volume index of 41.65 mL/g, 51.27% COD removal and 76.48% total suspended solid removal. In contrast, FeCl3 alone achieved slightly better COD and total suspended solid removal rates, however it resulted in higher sludge volume index and sludge production. The combined use of RSA and FeCl3 reduced the consumption of these two coagulants by 78.76% and 46.69% respectively. Functional groups and thermal stability of the flocs showed that RSA + FeCl3 synergistically enhance the mechanisms of the coagulation-flocculation process, including adsorption by particle's bridging, charge neutralization and size of flocs. Combining the coagulants resulted in increased van der Waals forces and lower attractive forces of the inter-colloidal energy barrier in the leachate. Additionally, the highest and lowest heavy metals removal rates for treatment by microfiltration were found for Fe (92.15%) and Mg (7.63%), with a total heavy metals removal efficiency in the range of 6.08-90.78%. The findings of this study show that RSA can serve as a natural eco-friendly coagulant both alone and in combination with FeCl3 in the leachate treatment.

Effects of physical method and enzymatic hydrolysis on the properties of soybean fiber-rich stabilizer for oil in water emulsions.

BACKGROUND: Okara is a by-product from the soybean industry and an abundant resource of insoluble soybean fiber (ISF). ISF with various properties could be obtained by different extraction methods. It is an attractive option to utilize okara by taking advantage of ISF as an emulsifier or stabilizer. RESULTS: Compared with the untreated ISF (ISFUT ), superfine grinding reduced the particle size and viscosity of ISF (ISFSG ). Steam explosion increased the water solubility from 17.5% to 51.7% but decreased the water holding capacity and swelling capacity of ISF (ISFSE ) from 15.0 and 14.0 g/g to 4.2 and 3.3 g/g, respectively. Emulsions prepared by ISFUT and ISFSG before or after enzymatic hydrolysis presented large oil droplets and were unstable. Although emulsions prepared by ISFSE after enzymatic hydrolysis (ISFSE-E ) showed flocculation, the volume-weighted average diameter (19.7 µm) were the smallest while the viscosity and viscoelastic modulus were the highest, and exhibited excellent physical stability during storage. CONCLUSION: ISF obtained by physical and hydrolysis treatment displayed diverging physicochemical properties while ISF prepared by steam explosion-enzymatic hydrolysis presented the best potential to stabilize emulsions. The present study could provide novel information about the utilization of okara by the application of ISF as an emulsifier or stabilizer. © 2023 Society of Chemical Industry.

Wilderness Medical Society Clinical Practice Guidelines on Water Treatment for Wilderness, International Travel, and Austere Situations: 2024 Update.

To provide guidance to medical providers, wilderness users, and travelers, the Wilderness Medical Society convened an expert panel to develop evidence-based guidelines for treating water in situations where the potability of available water is not assured, including wilderness and international travel, areas impacted by disaster, and other areas without adequate sanitation. The guidelines present the available methods for reducing or eliminating microbiological contamination of water for individuals, groups, or households; evaluation of their effectiveness; and practical considerations. The evidence base includes both laboratory and clinical publications. The panel graded the recommendations based on the quality of supporting evidence and the balance between benefits and risks/burdens according to the criteria published by the American College of Chest Physicians.

Effect of FeCl3 concentration in chemically enhanced primary treatment on the performance of a conventional wastewater treatment plant. A case study.

The effect of coagulant dosage in a chemically enhanced primary treatment (CEPT) on the performance of a conventional wastewater treatment plant (WWTP) has been investigated. Lab-scale experiments simulations were carried out in order to evaluate the effect of coagulant addition on the primary settling performance. In these experiments, FeCl3 was used as coagulant. Later, the WWTP was theoretically simulated using a commercial software (WEST®) to evaluate the effect of coagulation/flocculation on the global system, based on the results obtained at lab-scale. According to these results, the CEPT modifies the organic matter balance in the WWTP, decreasing the contribution of readily (SS) and slowly (XS) biodegradable fractions of COD to the aerobic biological process up to 27.3% and 80.8%, respectively, for a dosage of FeCl3 of 24 mg L-1. Consequently, total suspended solids in the aerobic reactor and the secondary purged sludge decreased up to 33% and 13%, respectively. However, the influence on effluent quality was negligible. On the contrary, suspended solids concentration in the sludge to be treated by anaerobic digestion increased, mainly regarding the Ss and Xs fractions, which caused an 8.1% increase in biogas production potential, with approximately 60% of CH4 concentration.

Synthesis of chitosan-based grafting magnetic flocculants for flocculation of kaolin suspensions.

A series of novel chitosan-based magnetic flocculants FS@CTS-P(AM-DMC) was prepared by molecular structure control. The characterization results showed that FS@CTS-P(AM-DMC) had a uniform size of about 21.46 nm, featuring a typical core-shell structure, and the average coating layer thickness of CTS-P(AM-DMC) was about 5.03 nm. FS@CTS-P(AM-DMC) exhibited excellent flocculation performance for kaolin suspension, achieved 92.54% turbidity removal efficiency under dosage of 150 mg/L, pH 7.0, even at high turbidity (2000 NTU) with a removal efficiency of 96.96%. The flocculation mechanism was revealed to be dominated by charge neutralization under acidic and neutral conditions, while adsorption and bridging effects play an important role in alkaline environments. The properties of magnetic aggregates during flocculation, breakage, and regeneration were studied at different pH levels and dosages. In the process of magnetophoretic, magnetic particles collide and adsorb with kaolin particles continuously due to magnetic and electrostatic attraction, transform into magnetic chain clusters, and then further form three-dimensional network magnetic aggregates that can capture free kaolin particles and other chain clusters. Particle image velocimetry confirmed the formation of eddy current of magnetic flocs and experienced three stages: acceleration, stabilization, and deceleration.

Sequential inoculation of flocculent Torulaspora delbrueckii with Saccharomyces cerevisiae increases color density of Pinot Noir wines.

Pinot noir grapes require careful management in the winery to prevent loss of color density and promote aging stability. Winemaking with flocculent yeast has been shown to increase color density, which is desirable to consumers. This research explored interspecies sequential inoculation and co-flocculation of commercial yeast on Pinot noir wine color. Sedimentation rates of six non-Saccharomyces species and two Saccharomyces cerevisiae strains were assayed individually and in combination. The most flocculent pairings, Torulaspora delbrueckii BIODIVA with S. cerevisiae RC212 or VL3, were used to ferment 20 L Pinot noir must. Sequential fermentations produced wines with greater color density at 420 + 520 nm, confirmed by sensory panel. Total and monomeric anthocyanin concentrations were decreased in sequentially fermented wines, despite being the main source of red wine color. BIODIVA adsorbed more anthocyanins than S. cerevisiae, indicating a greater number of cell wall mannoproteins in flocculent yeast, that could then result in a later release of anthocyanins and enhance copigment formation in red wines.

An RpoN-dependent PEP-CTERM gene is involved in floc formation of an Aquincola tertiaricarbonis strain.

BACKGROUND: The floc is a characteristic of microbial aggregate growth, displaying cloudy suspensions in water. Floc formation has been demonstrated in a series of bacteria and the floc-forming bacteria play a crucial role in activated sludge (AS) process widely used for municipal sewage and industrial wastewater treatment over a century. It has been demonstrated that some exopolysaccharide biosynthesis genes and the sigma factor (sigma54 or rpoN) were required for floc forming in some bacteria. However, the mechanism underlying the floc formation stills need to be elucidated. RESULTS: In this study, we demonstrate that a TPR (Tetratricopeptide repeats) protein-encoding gene prsT is required for floc formation of Aquincola tertiaricarbonis RN12 and an upstream PEP-CTERM gene (designated pepA), regulated by RpoN1, is involved in its floc formation but not swarming motility and biofilm formation. Overexpression of PepA could rescue the floc-forming phenotype of the rpoN1 mutant by decreasing the released soluble exopolysaccharides and increasing the bound polymers. CONCLUSION: Our results indicate that the wide-spread PEP-CTERM proteins play an important role in the self-flocculation of bacterial cells and may be a component of extracellular polymeric substances required for floc-formation.

Intracellular accumulation of c-di-GMP and its regulation on self-flocculation of the bacterial cells of Zymomonas mobilis.

Zymomonas mobilis is an emerging chassis for being engineered to produce bulk products due to its unique glycolysis through the Entner-Doudoroff pathway with less ATP produced for lower biomass accumulation and higher product yield. When self-flocculated, the bacterial cells are more productive, since they can self-immobilize within bioreactors for high density, and are more tolerant to stresses for higher product titers, but this morphology needs to be controlled properly to avoid internal mass transfer limitation associated with their strong self-flocculation. Herewith we explored the regulation of cyclic diguanosine monophosphate (c-di-GMP) on self-flocculation of the bacterial cells through activating cellulose biosynthesis. While ZMO1365 and ZMO0919 with GGDEF domains for diguanylate cyclase activity catalyze c-di-GMP biosynthesis, ZMO1487 with an EAL domain for phosphodiesterase activity catalyzes c-di-GMP degradation, but ZMO1055 and ZMO0401 contain the dual domains with phosphodiesterase activity predominated. Since c-di-GMP is synthesized from GTP, the intracellular accumulation of this signal molecule through deactivating phosphodiesterase activity is preferred for activating cellulose biosynthesis to flocculate the bacterial cells, because such a strategy exerts less perturbance on intracellular processes regulated by GTP. These discoveries are significant for not only engineering unicellular Z. mobilis strains with the self-flocculating morphology to boost production but also understanding mechanism underlying c-di-GMP biosynthesis and degradation in the bacterium.

Parametric and kinetic studies of activated sludge dewatering by cationic chitosan-like bioflocculant BF01314 produced from Citrobacter youngae.

Bacterial strains belonging to Citrobacter spp. were reported to produce polysaccharides consisting of N-acetylglucosamine and glucosamine like chitosan, with high flocculation activity. In this work, the flocculation dewatering performance of activated sludge conditioned by a novel cationic chitosan-like bioflocculant (BF) named BF01314, produced from Citrobacter youngae GTC 01314, was evaluated under the influences of flocculant dosage, pH, and temperature. At BF dosage as low as 0.5 kg/t DS, the sludge dewaterability was significantly enhanced in comparison to the raw (untreated) sludge, featuring well-flocculated characteristic (reduction in CST from 22.0 s to 9.4 s) and good sludge filterability with reduced resistance (reduction in SRF by one order from 7.42 × 1011 to 9.59 × 1010 m/kg) and increased compactness of sludge (increase in CSC from 15.2 to 23.2%). Besides, the BF demonstrated comparable high sludge dewatering performance within the pH range between 2 and 8, and temperature range between 25 °C and 80 °C. Comparison between the BF, the pristine chitosan and the commercial cationic copolymer MF 7861 demonstrated equivalent performance with enhanced dewaterability at the dosage between 2.0 and 3.0 kg/t DS. Besides, the BF demonstrated strong flocculation activity (>99%) when added to the sludge suspension using moderate to high flocculation speeds (100-200 rpm) with at least 3-min mixing time. The BF's reaction in sludge flocculation was best fitted with a pseudo first-order kinetic model. Electrostatic charge patching and polymer bridging mechanisms are believed to be the dominant mechanistic phenomena during the BF's sludge conditioning process (coagulation-flocculation).

Promoting dewatering efficiency of sludge by bioleaching coupling chemical flocculation.

In recent years, bioleaching has emerged as a cost-effective technology for enhancing the dewaterability of sludge. However, the lengthy treatment time involved in sludge bioleaching processes limits daily treatment capacity for sludge. Here, a novel approach was developed through a short time of sludge bioleaching with A. ferrooxidans LX5 (A. f) and A. thiooxidans TS6 (A. t) followed by polyferric sulfate (PFS) flocculation (A. f + A. t + PFS). After 12.5 h of the A. f + A. t + PFS treatment (30% A. f, 10% A. t, 40 mg/g DS S0, 60 mg/g DS FeSO4•7H2O, and 120 mg/g DS PFS), the reduction efficiency of specific resistance to filtration (SRF) and sludge cake moisture content reached 94.0% and 11.6%, respectively, which were comparable to the results achieved through 24 h of completed bioleaching treatment. In pilot-scale applications, the mechanical dewatering performance was notably improved following A. f + A. t + PFS treatment, with the low moisture content of the treated sludge cake (∼59.2%). This study provides new insights into the A. f + A. t + PFS process and holds potential for developing efficient and promising sludge dewatering strategies in engineering application.

Disinfection of treated urban effluents for reuse by combination of coagulation/flocculation and Fenton processes.

In this study, a combination of coagulation/flocculation and Fenton processes was studied as tertiary treatment in order to generate treated water susceptible to reuse. The combination of both processes has never been applied in disinfection of real urban wastewater. The best removals of turbidity and enterobacteria were achieved when applying a coagulant (FeCl3) dosage of 120 mg/L and the natural pH of the effluent (7.14). The following Fenton reaction presented the maximal enterobacteria inactivation after 120 min at 25 °C, when using hydrogen peroxide and added iron concentrations of 100 mg/L and 7 mg/L, respectively. The abundance of antibiotic resistant (amoxicillin and sulfamethoxazole) enterobacteria and total enterobacteria, enterococci, and heterotrophs, and antibiotic resistance genes - ARG - (sul1, blaTEM and qnrS) was evaluated before and after each step of the treatment. Values below 10 CFU/100 mL were achieved for total and resistant cultivable enterobacteria immediately after treatment and after storage for 72 h, therefore meeting the strictest limit imposed for E. coli. Physico-chemical parameters also met the established limits for water reuse. Despite harbouring a rich and diverse bacterial community, the final stored disinfected wastewater contained high relative abundance of potentially hazardous bacteria. Such results point out the need of a deep microbiological characterization of treated wastewater to evaluate the risk of its reuse in irrigation.

Enhancement of EDDS-photo-Fenton process with plant-based coagulants for winery wastewater management.

To achieve an efficient remediation of a winery wastewater (WW), it was studied a physical-chemical process (coagulation-flocculation-decantation - CFD) involving plant-based coagulants (PBC) with advanced oxidation processes (AOPs), aiming to achieve the Portuguese legal limits. Initially, one invasive (Acacia dealbata) and three native species (Quercus ilex, Platanus x acerifólia and Tanacetum vulgare) were collected and used as plant-based coagulants (PBCs). The combination of Platanus acerifólia (P.a.) seeds with polyvinylpolypyrrolidone (PVPP) achieved high turbidity (97.3%) and chemical oxygen demand (COD = 48.2%) removals, from raw WW, with [PBC] = 0.1 g/L, [PVPP] = 5 mg/L, pH = 3.0, fast mix = 150 rpm/3 min, slow mix = 20 rpm/20 min, sedimentation time = 12 h. Different AOPs were studied to treat raw WW, with photo-Fenton process revealing the highest COD efficiency (88.0%). To enhance the capabilities of photo-Fenton, ethylenediamine-N,N'-disuccinic acid trisodium salt (EDDS) was assessed as a chelation agent, reducing iron precipitation. The pre-treatment of WW by PBCs followed by EDDS/photo-Fenton (pH = 6.0, [H2O2] = 175 mM, [Fe2+] = 5 mM, [EDDS] = 1 mM, T = 298 K, time = 240 min) increased the COD removal, whatever the radiation source applied (UV-C, UV-A and solar). Among the different processes, the combined P. a. seeds and UV-C/EDDS/Fenton allowed increase the WW biodegradability from 0.26 to 0.46, and achieved a COD removal of 95.7%, reaching the Portuguese legal limits. As final remark, the synergy of PBCs and EDDS/photo-Fenton is considered effective and sustainable process for raw WW remediation and water reuse.

Novel thermodynamic mechanisms of co-conditioning with polymeric aluminum chloride and polyacrylamide for improved sludge dewatering: A paradigm shift in the field.

This study investigated the combined effects of polymeric aluminum chloride (PAC) and polyacrylamide (PAM) on sludge dewatering, aiming to unveil underlying mechanisms. Co-conditioning with 15 mg g-1 PAC and 1 mg g-1 PAM achieved optimal dewatering, reducing specific filtration resistance (SFR) of co-conditioned sludge to 4.38 × 1012 m-1kg-1, a mere 48.1% of raw sludge's SFR. Compared with the CST of raw sludge (36.45 s), sludge sample can be significantly reduced to 17.7 s. Characterization tests showed enhanced neutralization and agglomeration in co-conditioned sludge. Theoretical calculations revealed elimination of interaction energy barriers between sludge particles post co-conditioning, converting sludge surface from hydrophilic (3.03 mJ m-2) to hydrophobic (-46.20 mJ m-2), facilitating spontaneous agglomeration. Findings explain improved dewatering performance. Based on Flory-Huggins lattice theory, connection between polymer structure and SFR was established. Raw sludge formation triggered significant change in chemical potential, increasing bound water retention capacity and SFR. In contrast, co-conditioned sludge exhibited thinnest gel layer, reducing SFR and significantly improving dewatering. These findings represent a paradigm shift, shedding new light on fundamental thermodynamic mechanisms of sludge dewatering with different chemical conditioning.

Treatment technologies for olive mill wastewater with impacts on plants.

Olive mill wastewater (OMW), produced during olive oil production, contains high levels of salt contents, organic matter, suspended particles, and toxic chemicals (particularly phenols), which all result in increased biological and chemical oxygen demand. Olive Oil Mills' Wastes (OMW), which have dark brown color with unpleasant smell, consist mainly of water, high organic (mainly phenols and polyphenols) and low inorganic compounds (e.g. potassium and phosphorus), as well as grease. OMW components can negatively affect soil's physical, chemical, and biological properties, rendering it phytotoxic. However, OMW can positively affect plants' development when it's applied to the soil after pretreatment and treatment processes due to its high mineral contents and organic matter. There are various approaches for removing impurities and the treatment of OMW including chemical, biological, thermal, physiochemical, and biophysical processes. Physical techniques involve filtration, dilution, and centrifugation. Thermal methods include combustion and pyrolysis; biological techniques use anaerobic and aerobic techniques, whereas adsorption and electrocoagulation act as physiochemical methods, and coagulation and flocculation as biophysical methods. In contrast, combined biological treatment methods use co-digestion and composting. A comparison of the effects of both treated and untreated OMW samples on plant development and soil parameters can help us to understand the potential role of OMW in increasing soil fertility. This review discusses the impacts of untreated OMW and treated OMW in terms of soil characteristics, seed germination, and plant growth. This review summarizes all alternative approaches and technologies for pretreatment, treatment, and recovery of valuable byproducts and reuse of OMW across the world.