RESUMEN
Silicon (Si) anodes, free from the dendritic growth concerns found in lithium (Li) metal anodes, offer a promising alternative for high-energy all-solid-state batteries (ASSBs). However, most advancements in Si anodes have been achieved under impractical high operating pressures, which can mask detrimental electrochemo-mechanical issues. Herein, we effectively address the challenges related to the low-pressure operation of Si anodes in ASSBs by introducing an silver (Ag) interlayer between the solid electrolyte layer (Li6PS5Cl) and anode and prelithiating the anodes. The Si composite electrodes, consisting of Si/polyvinylidene fluoride/carbon nanotubes, are optimized for suitable mechanical properties and electrical connectivity. Although the impact of the Ag interlayer is insignificant at an exceedingly high operating pressure of 70 MPa, it substantially enhances the interfacial contacts under a practical low operating pressure of 15 MPa. Thus, Ag-coated Si anodes outperform bare Si anodes (discharge capacity: 2430 vs 1560 mA h g-1). The robust interfacial contact is attributed to the deformable, adhesive properties and protective role of the in situ lithiated Ag interlayer, as evidenced by comprehensive ex situ analyses. Operando electrochemical pressiometry is used effectively to probe the strong interface for Ag-coated Si anodes. Furthermore, prelithiation through the thermal evaporation deposition of Li metal significantly improves the cycling performance.
RESUMEN
The rapid proliferation of power sources equipped with lithium-ion batteries poses significant challenges in terms of post-scrap recycling and environmental impacts, necessitating urgent attention to the development of sustainable solutions. The cathode direct regeneration technologies present an optimal solution for the disposal of degraded cathodes, aiming to non-destructively re-lithiate and straightforwardly reuse degraded cathode materials with reasonable profits and excellent efficiency. Herein, a potential-regulated strategy is proposed for the direct recycling of degraded LiFePO4 cathodes, utilizing low-cost Na2SO3 as a reductant with lower redox potential in the alkaline systems. The aqueous re-lithiation approach, as a viable alternative, not only enables the re-lithiation of degraded cathode while ignoring variation in Li loss among different feedstocks but also utilizes the rapid sintering process to restore the cathode microstructure with desirable stoichiometry and crystallinity. The regenerated LiFePO4 exhibits enhanced electrochemical performance with a capacity of 144 mA h g-1 at 1 C and a high retention of 98% after 500 cycles at 5 C. Furthermore, this present work offers considerable prospects for the industrial implementation of directly recycled materials from lithium-ion batteries, resulting in improved economic benefits compared to conventional leaching methods.
RESUMEN
Among silicon-based anode family for Li-ion battery technology, SiOx, a nonstoichiometric silicon suboxide holds the potential for significant near-term commercial impact. In this context, this study mainly focuses on demonstrating an innovative SiOx@C anode design that adopts a pre-lithiation strategy based on in situ pyrolysis of Li-salt of silsesquioxane trisilanolate without the need for lithium metal or active lithium compounds and creates dual carbon encapsulation of SiOC nanodomains by simply one-step thermal treatment. This ingenious design ensures the pre-lithiation process and pre-lithiation material with high-environmental stability. Moreover, phenyl-rich organosiloxane clusters and polyacrylonitrile polymers are expected to serve as internal and external carbon source, respectively. The formation of an interpenetrating and continuous carbon matrix network would not only synergistically offer an improved electrochemical accessibility of active sites but also alleviate the volume expansion effect during cycling. As a result, this new type of anode delivered a high reversible capacity, remarkable cycle stability as well as excellent high-rate capability. In particular, the L2-SiOx@C material has a high initial coulomb efficienc of 80.4% and, after 500 cycles, a capacity retention as high as 97.5% at 0.5 A g-1 with a reversible specific capacity of 654.5 mA h g-1.
RESUMEN
The first crystal structure of an ortho-lithium phosphinothioic amide complexed with tetramethylethylenediamine 12 is reported. The complex consists of a spirane in which the spiro-lithium is N,N- and C,S-chelated by the diamine and organophosphorus ligands, respectively. The analogous ortho anion 14 obtained by Sn(IV)/Li transmetallation in THF has also been synthesized. Nuclear magnetic resonance study of both anions showed that they exist as monomers in solution and are involved in dynamic processes including the restricted rotation around the P-N bond. 14 is converted at room temperature by nucleophilic cyclization to the dearomatized anion 15, which evolves after a few hours to the benzophosphindole sulfide 16. Density functional theory calculations supported the aggregation state in solution and were used to explore the conformational space of anion 12, the mechanism of ortho-lithiation directed by P(X)-N (X=O, S) groups, and the mechanism of formation of 15.
RESUMEN
Bicyclo[1.1.1]pentane (BCP) derivatives have attracted significant recent interest in drug discovery as alkyne, tert-butyl and arene bioisosteres, where their incorporation is frequently associated with increased compound solubility and metabolic stability. While strategies for functionalisation of the bridgehead (1,3) positions are extensively developed, platforms allowing divergent substitution at the bridge (2,4,5) positions remain limited. Recent reports have introduced 1-electron strategies for arylation and incorporation of a small range of other substituents, but are limited in terms of scope, yields or practical complexity. Herein, we show the synthesis of diverse 1,2,3-trifunctionalised BCPs through lithium-halogen exchange of a readily accessible BCP bromide. When coupled with medicinally relevant product derivatisations, our developed 2-electron "late stage" approach provides rapid and straightforward access to unprecedented BCP structural diversity (>20â hitherto-unknown motifs reported). Additionally, we describe a method for the synthesis of enantioenriched "chiral-at-BCP" bicyclo[1.1.1]pentanes through a novel stereoselective bridgehead desymmetrisation.
RESUMEN
Li-CO2 batteries facilitate renewable energy storage in a cost-effective, eco-friendly manner. However, an inadequate understanding of their reaction mechanism severely impedes their development. Here we outline recent mechanistic advances in the discharge processes of Li-CO2 batteries, particularly in terms of the theoretical aspect. First, the vital factors affecting the formation of discharge intermediates are highlighted, and a surface lithiation mechanism predominantly applicable to catalysts with weak CO2 adsorption is proposed. Subsequently, the modeling of the chemical potential of Li++e-, which is crucial for the evaluation of the theoretical limiting voltage, is detailed. Finally, challenges and future directions pertaining to the further development of Li-CO2 are discussed. In essence, this concept article seeks to inspire future experimental and theoretical studies in advancing the development of Li-CO2 electrochemical technology.
RESUMEN
VO2 has shown great promise for sensors, smart windows, and energy storage devices, because of its drastic semiconductor-to-metal transition (SMT) near 340 K coupled with a structural transition. To push its application toward room-temperature, effective transition temperature (Tc) tuning in VO2 is desired. In this study, tailorable SMT characteristics in VO2 films have been achieved by the electrochemical intercalation of foreign ions (e.g., Li ions). By controlling the relative potential with respect to Li/Li+ during the intercalation process, Tc of VO2 can be effectively and systematically tuned in the window from 326.7 to 340.8 K. The effective Tc tuning could be attributed to the observed strain and lattice distortion and the change of the charge carrier density in VO2 introduced by the intercalation process. This demonstration opens up a new approach in tuning the VO2 phase transition toward room-temperature device applications and enables future real-time phase change property tuning.
RESUMEN
Layered oxides with ultrahigh nickel content are considered promising high energy cathode materials. However, their cycle stability is constrained by a series of heterogeneous structural transformations during the complex solid-state lithiation process. By in-depth investigation into the solid-state lithiation process of LiNi0.92Co0.04Mn0.04O2, it is found that the protruded parts on the surface of precursor particles tend to be surrounded by locally excessive LiOH, which promotes the formation of a rigid and dense R 3 - m ${{\rm { R}}\mathrel{\mathop{{\rm { 3}}}\limits^{{\rm -}}}{\rm { m}}}$ shell during the early stage of lithiation process. The shell will hinder the diffusion of lithium and topotactic lithiation within the particles, culminating in spatially heterogeneous intermediates that can impair the electrochemical properties of the cathode material. The spheroidization of the precursor can enhance uniformity in structural evolution during solid-phase lithiation. Ultrahigh nickel cathodes derived from spherical precursors demonstrate high initial discharge specific capacity (234.2â mAh g-1, in the range of 2.7-4.3â V) and capacity retention (89.3 % after 200â cycles), significantly superior to the non-spherical samples. This study not only sheds light on the intricate relationship between precursor shape and structural transformation but also introduces a novel strategy for enhancing cathode performance through precursor spheroidization.
RESUMEN
Application of silicon-based anodes is significantly challenged by low initial Coulombic efficiency (ICE) and poor cyclability. Traditional pre-lithiation reagents often pose safety concerns due to their unstable chemical nature. Achieving a balance between water-stability and high ICE in prelithiated silicon is a critical issue. Here, we present a lithium-enriched silicon/graphite material with an ultra-high ICE of ≥110 % through a high-stable lithium pre-storage methodology. Lithium pre-storage prepared a nano-drilled graphite material with surficial lithium functional groups, which can form chemical bonds with adjacent silicon during high-temperature sintering. This results in an unexpected O-Li-Si interaction, leading to in situ pre-lithiation of silicon nanoparticles and providing high stability in air and water. Additionally, the lithium-enriched silicon/graphite materials impart a combination of high ICE, high specific capacity (620â mAh g-1), and long cycling stability (>400 cycles). This study opens up a promising avenue for highly air- and water-stable silicon anode prelithiation methods.
RESUMEN
Pre-lithiation via electrolysis, herein defined as electrolytic pre-lithiation, using cost-efficient electrolytes based on lithium chloride (LiCl), is successfully demonstrated as a proof-of-concept for enabling lithium-ion battery full-cells with high silicon content negative electrodes. An electrolyte for pre-lithiation based on γ-butyrolactone and LiCl is optimized using boron-containing additives (lithium bis(oxalato)borate, lithium difluoro(oxalate)borate) and CO2 with respect to the formation of a protective solid electrolyte interphase (SEI) on silicon thin films as model electrodes. Reversible lithiation in Si||Li metal cells is demonstrated with Coulombic efficiencies (CEff ) of 95-96% for optimized electrolytes comparable to 1 m LiPF6 /EC:EMC 3:7. Formation of an effective SEI is shown by cyclic voltammetry and X-ray photoelectron spectroscopy (XPS). electrolytic pre-lithiation experiments show that notable amounts of the gaseous product Cl2 dissolve in the electrolyte leading to a self-discharge Cl2 /Cl- shuttle mechanism between the electrodes lowering pre-lithiation efficiency and causing current collector corrosion. However, no significant degradation of the Si active material and the SEI due to contact with elemental chlorine is found by SEM, impedance, and XPS. In NCM111||Si full-cells, the capacity retention in the 100th cycle can be significantly increased from 54% to 78% by electrolytic pre-lithiation, compared to reference cells without pre-lithiation of Si.
RESUMEN
Highly enantiomerically enriched dihydrohydroquinolines were prepared in two steps from quinoline. Addition of aryllithiums to quinoline with tert-butoxycarbonyl (Boc) protection gave N-Boc-2-aryl-1,2-dihydroquinolines. These were treated with n-butyllithium and electrophilic trapping occurred exclusively at C-4 of the dihydroquinoline, a result supported by DFT studies. Variable temperature NMR spectroscopy gave kinetic data for the barrier to rotation of the carbonyl group (ΔG≠ ≈49â kJ mol-1 , 195â K). Lithiation using the diamine sparteine allowed kinetic resolutions with high enantioselectivities (enantiomer ratio up to 99 : 1). The enantioenriched 1,2-dihydroquinolines could be converted to 1,4-dihydroquinolines with retention of stereochemistry. Further functionalisation led to trisubstituted products. Reduction provided enantioenriched tetrahydroquinolines, whereas acid-promoted removal of Boc led to quinolines, and this was applied to a synthesis of the antimalarial compound M5717.
RESUMEN
Silica (SiO2)-based materials are a promising alternative anode material due to their high specific capacity, abundance, safety, and environmental friendliness. However, the significant volume expansion and the formation of a solid electrolyte interphase (SEI) with electrolytes cause active lithium loss and result in poor Coulombic efficiency of SiO2-based materials, which hinder their commercial applications. Therefore, pre-lithiation, a method of embedding extra lithium ions in the electrodes prior to cycling, is an effective approach to replenish the largely irreversible lithium loss during cycling and overcomes these challenges. In this study, carbon-coated silica (SiO2@C) nano composite was synthesized via a sol-gel method and the beneficial impacts of using pre-lithiated SiO2@C electrodes in coin cells were investigated. It is shown that the carbon coating onto the surface of the SiO2particles and the pre-lithiation method led to a distinct improvement in the overall capacity and Coulombic efficiency of the cells due to the pre-formed SEI and the presence of a lithium reservoir within the anode. Furthermore, the anodes exhibited excellent cycling stability and good rate capability up to 2 A g-1.
RESUMEN
Ion intercalation assisted exfoliation is the oldest and most popular method for the scalable synthesis of molybdenum disulfide (MoS2) nanosheets. The commonly used organolithium reagents for Li+ intercalation are n-butyllithium (n-BuLi) and naphthalenide lithium (Nap-Li); however, the highly pyrophoric nature of n-BuLi and the overly reducing power of Nap-Li hinder their extensive application. Here, a novel organolithium reagent, pyrene lithium (Py-Li), which has intrinsic safe properties and a well-matched redox potential, is reported for the intercalation and exfoliation of MoS2. The redox potential of Py-Li (0.86 V vs Li+/Li) is located just between the intercalation (1.13 V) and decomposition (0.55 V) potentials of bulk MoS2, thus allowing precise Li+ intercalation to form a lamellar LiMoS2 compound without undesirable structural damage. The lithiation reaction can be accomplished within 1 h at room temperature and the exfoliated nanosheets are almost single layer. This method also offers the advantages of low cost, high repeatability, and ease in realizing large-scale production.
RESUMEN
In this contribution, the first amidinate and amidine derivatives of p-carborane are described. Double lithiation of p-carborane (1) with n-butyllithium followed by treatment with 1,3-diorganocarbodiimides, R-N=C=N-R (R = iPr, Cy (= cyclohexyl)), in DME or THF afforded the new p-carboranylamidinate salts p-C2H10B10[C(NiPr)2Li(DME)]2 (2) and p-C2H10B10[C(NCy)2Li(THF)2]2 (3). Subsequent treatment of 2 and 3 with 2 equiv. of chlorotrimethylsilane (Me3SiCl) provided the silylated neutral bis(amidine) derivatives p-C2H10B10[C{iPrN(SiMe3)}(=NiPr)]2 (4) and p-C2H10B10[C{CyN(SiMe3)}(=NCy)]2 (5). The new compounds 3 and 4 have been structurally characterized by single-crystal X-ray diffraction. The lithium carboranylamidinate 3 comprises a rare trigonal planar coordination geometry around the lithium ions.
RESUMEN
Pyrrolopyrimidines are important scaffolds for the preparation of bioactive molecules. Therefore, developing efficient and flexible ways for selective functionalization of the pyrrolopyrimidine skeleton is of interest. We have investigated lithiation-addition at C-6 of protected 4-chloro-7H-pyrrolo [2,3-d]pyrimidine as a route to new building blocks for medicinal chemistry. It was found that bis(2-dimethylaminoethyl) ether as an additive increased the yield in the additional reaction with benzaldehyde. Deuterium oxide quench experiments showed that this additive offered both a higher degree of lithiation and increased stability of the lithiated intermediate. The substrate scope of the protocol was investigated with 16 aldehydes and ketones, revealing the method to be excellently suited for reaction with aldehydes, cyclohexanone derivatives and 2,2,2-trifluoroacetophenone, while being less efficient for acetophenones. Yields in the range of 46-93% were obtained.
RESUMEN
The cobalt bis(dicarbollide)(1-) anion (1-), [(1,2-C2B9H11)2-3,3'-Co(III)](1-), plays an increasingly important role in material science and medicine due to its high chemical stability, 3D shape, aromaticity, diamagnetic character, ability to penetrate cells, and low cytotoxicity. A key factor enabling the incorporation of this ion into larger organic molecules, biomolecules, and materials, as well as its capacity for "tuning" interactions with therapeutic targets, is the availability of synthetic routes that enable easy modifications with a wide selection of functional groups. Regarding the modification of the dicarbollide cage, syntheses leading to substitutions on boron atoms are better established. These methods primarily involve ring cleavage of the ether rings in species containing an oxonium oxygen atom connected to the B(8) site. These pathways are accessible with a broad range of nucleophiles. In contrast, the chemistry on carbon vertices has remained less elaborated over the previous decades due to a lack of reliable methods that permit direct and straightforward cage modifications. In this review, we present a survey of methods based on metalation reactions on the acidic C-H vertices, followed by reactions with electrophiles, which have gained importance in only the last decade. These methods now represent the primary trends in the modifications of cage carbon atoms. We discuss the scope of currently available approaches, along with the stereochemistry of reactions, chirality of some products, available types of functional groups, and their applications in designing unconventional drugs. This content is complemented with a report of the progress in physicochemical and biological studies on the parent cobalt bis(dicarbollide) ion and also includes an overview of recent syntheses and emerging applications of boron-substituted compounds.
RESUMEN
Silicon (Si) has been considered to be one of the most promising anode materials for high energy density lithium-ion batteries (LIBs) due to its high theoretical capacity, low discharge platform, abundant raw materials and environmental friendliness. However, the large volume changes, unstable solid electrolyte interphase (SEI) formation during cycling and intrinsic low conductivity of Si hinder its practical applications. Various modification strategies have been widely developed to enhance the lithium storage properties of Si-based anodes, including cycling stability and rate capabilities. In this review, recent modification methods to suppress structural collapse and electric conductivity are summarized in terms of structural design, oxide complexing and Si alloys, etc. Moreover, other performance enhancement factors, such as pre-lithiation, surface engineering and binders are briefly discussed. The mechanisms behind the performance enhancement of various Si-based composites characterized by in/ex situ techniques are also reviewed. Finally, we briefly highlight the existing challenges and future development prospects of Si-based anode materials.
RESUMEN
A one-pot lithiation-phosphonylation procedure was elaborated as a method to prepare heteroaromatic phosphonic acids. It relied on the direct lithiation of heteroaromatics followed by phosphonylation with diethyl chlorophosphite and then oxidation with hydrogen peroxide. This protocol provided the desired phosphonates with satisfactory yields. This procedure also had some limitations in its dependence on the accessibility and stability of the lithiated heterocyclic compounds. The same procedure could be applied to phosphonylation of aromatic compounds, which do not undergo direct lithiation and thus require the use of their bromides as substrates. The obtained compounds showed weak antiproliferative activity when tested on three cancer cell lines.
RESUMEN
This work shows why it is imperious to use an excess of butyllithium for a directed ortho-lithiation of a trifluoromethyl sulfoximine. The analysis of mixtures of n-BuLi and sulfoximine 1 in THF-d8 using {1 H, 6 Li, 13 C, 15 N, 19 F} NMR experiments at low temperatures reveal that a first deprotonation occurs that leads to dimeric and tetrameric N-lithiated sulfoximine (93 : 7). Using an excess n-BuLi (5â equivalents), the second deprotonation on the ortho-position of the aromatic occurs. Six species were observed and characterized on the way. It includes three aggregates involving a sulfoximine: i)â a [dilithiated sulfoximine/(n-BuLi)] dimer solvated by four molecules of THF (Agg2, 39 %); ii)â a [dilithiated sulfoximine/(n-BuLi)3 ] tetramer solvated by six molecules of THF (Agg3, 39 %); iii)â a [dilithiated sulfoximine/(n-BuOLi)3 ] tetramer solvated by four molecules of THF (Agg1, 22 %). A DFT study afforded optimized solvated structures for all these aggregates, fully consistent with the NMR data.
RESUMEN
Enones are widely utilized linchpin functional groups in chemical synthesis and molecular biology. We herein report the direct conversion of boronic esters into enones using commercially available methoxyallene as a three-carbon building block. Following boronate complex formation by reaction of the boronic ester with lithiated-methoxyallene, protonation triggers a stereospecific 1,2-migration before oxidation generates the enone. The protocol shows broad substrate scope and complete enantiospecificity is observed with chiral migrating groups. In addition, various electrophiles could be used to induce 1,2-migration and give a much broader range of α-functionalized enones. Finally, the methodology was applied to a 14-step synthesis of the enone-containing polyketide 10-deoxymethynolide.