High Efficiency and Low Roll-Off Pure-Red Perovskite LED Enabled by Simultaneously Inhibiting Auger and Trap Recombination of Quantum Dots.

CsPbI3 perovskite quantum dots (QDs) could achieve pure-red emission by reducing their size, but the increased exciton binding energy (EB) and surface defects for the small-sized QDs (SQDs) cause severe Auger and trap recombinations, thus worsening their electroluminescence (EL) performance. Herein, we utilize the dangling bonds of the SQDs as a driving force to accelerate KI dissolution to solve its low solubility in nonpolar solvents, thereby allowing K+ and I- to bond to the surface of SQDs. The EB of the SQDs was decreased from 305 to 51 meV because of the attraction of K+ to electrons, meanwhile surface vacancies were passivated by K+ and I-. The Auger and trap recombinations were simultaneously suppressed by this difunctional ligand. The SQD-based light-emitting diode showed a stable pure-red EL peak of 639 nm, an external quantum efficiency of 25.1% with low roll-off, and a brightness of 5934 cd m-2.

Efficient Quasi-2D Perovskite Based Blue Light-Emitting Diodes with Carbon Dots Modified Hole Transport Layer.

Quasi-2D perovskites based blue light-emitting diodes (LEDs) suffer from its poor electroluminescence performance, mainly caused by the nonradiative recombination in in defect-rich low-n phases and the unbalanced hole-electron injection in the device. Here, we developed a highly efficient quasi-2D perovskite based sky-blue LEDs behaving recorded external quantum efficiency (EQE) of 21.07% by employing carbon dots (CDs) as additives in the hole transport layer (HTL). We ascribe the high EQE to the effective engineering of CDs: (1) The CDs at the interface of HTLs can suppress the formation of low-efficient n = 1 phase, resulting a high luminescence quantum yield and energy transfer efficiency of the mixed n-phase quasi-2D perovskites. (2) The CDs additives can reduce the conductivity of HTL, partially blocking the hole injection, and thus making more balanced hole-electron injection. The CDs-treated devices have excellent Spectral stability and enhanced operational stability and could be a new alternative additive in the perovskite optoelectronic devices.

High-Efficiency and Emission-Tunable Inorganic Blue Perovskite Light-Emitting Diodes Based on Vacuum Deposition.

The fabrication of perovskite light-emitting diodes (PeLEDs) with vacuum deposition shows great potential and commercial value in realizing large-area display panel manufacturing. However, the electroluminescence (EL) performance of vacuum-deposited PeLEDs still lags behind the counterparts fabricated by solution process, especially in the field of blue PeLEDs. Here, the fabrication of high-quality CsPbBr3- x Clx film through tri-source co-evaporation is reported to achieve high photoluminescence quantum yield (PLQY). Compared with the conventional traditional dual-source co-evaporation, the tri-source co-evaporation method allows for freely adjustable elemental ratios, enabling the introduction of the lattice-matched Cs4 Pb(Br/Cl)6 phase with the quantum-limited effect into the inorganic CsPb(Br/Cl)3 emitter. By adjusting the phase distribution, the surface defects of the emitter can be effectively reduced, leading to better blue emission and film quality. Further, the effects of Cs/Pb ratio and Br/Cl ratio on the PLQY and carrier recombination dynamics of perovskite films are investigated. By optimizing the deposition rate of each precursor source, spectrally stable blue PeLEDs are achieved with tunable emission ranging from 468 to 488 nm. Particularly, the PeLEDs with an EL peak at 488 nm show an external quantum efficiency (EQE) of 4.56%, which is the highest EQE value for mixed-halide PeLEDs fabricated by vacuum deposition.

Tailoring Phase Distribution of Quasi-2D Perovskites via Taurine-Assistance Enables Efficient Blue Light-Emitting Diodes.

Quasi-2D (Q-2D) perovskites with typical varied n-phase structures deserve promising candidates in pursuing high-performance perovskite light-emitting diodes (PeLEDs). Whereas their weakness in precise n-phase distribution control disables the optical property of PeLEDs since the n = 1 phase is dominated by severe nonradiative recombination. Here, an effective phase distribution tailoring strategy is developed for pure blue PeLEDs by introducing taurine (TAU) into mixed halide Q-2D perovskites. The sulfonic acid group in TAU can coordinate with Pb2+ to suppress the formation of the n = 1 phase while promoting the growth of Q-2D perovskites into domains with the graded distribution of n = 2 and 3. The amino group in TAU forms hydrogen bonds with electronegative halide ions, suppressing the formation of halide vacancies and reducing the defect density in the Q-2D perovskite films. As a result, optimized blue Q-2D perovskite films boosted PLQY to 92%. Target blue PeLED  was endowed with a peak EQE of 14.82% (average 12.6%) at 475 nm and a maximum luminance of 1937 cd m-2 , which is among the reported high-level pure blue PeLEDs. This work demonstrates a feasible approach to regulate the phase distribution of Q-2D perovskites for high-performance blue PeLEDs.

Monoammonium Modified Dion-Jacobson Quasi-2D Perovskite for High Efficiency Pure-Blue Light Emitting Diodes.

Quasi-2D perovskites exhibit impressive optoelectronic properties and hold significant promise for future light-emitting devices. However, the efficiency of perovskite light-emitting diodes (PeLEDs) is seriously limited by defect-induced nonradiative recombination and imbalanced charge injection. Here, the defect states are passivated and charge injection balance is effectively improved by introducing the additive cyclohexanemethylammonium (CHMA) to bromide-based Dion-Jacobson (D-J) structure quasi-2D perovskite emission layer. CHMA participates in the crystallization of perovskite, leading to high quality film composed of compact and well-contacted grains with enhanced hole transportation and less defects. As a result, the corresponding PeLEDs exhibit stable pure blue emission at 466 nm with a maximum external quantum efficiency (EQE) of 9.22%. According to current knowledge, this represents the highest EQE reported for pure-blue PeLEDs based on quasi-2D bromide perovskite thin films. These findings underscore the potential of quasi-2D perovskites for advanced light-emitting devices and pave the way for further advancements in PeLEDs.

Strongly-Confined CsPbBr3 Perovskite Quantum Dots with Ultralow Trap Density and Narrow Size Distribution for Efficient Pure-Blue Light-Emitting Diodes.

The development of pure-blue perovskite light-emitting diodes (PeLEDs) faces challenges of spectral stability and low external quantum efficiency (EQE) due to phase separation in mixed halide compositions. Perovskite quantum dots (QDs) with strong confinement effects are promising alternatives to achieve high-quality pure-blue PeLEDs, yet their performance is often hindered by the poor size distribution and high trap density. A strategy combining thermodynamic control with a polishing-driven ligand exchange process to produce high-quality QDs is developed. The strongly-confined pure-blue (≈470 nm) CsPbBr3 QDs exhibit narrow size distribution (12% dispersion) and are achieved in Br-rich ion environment based on growth thermodynamic control. Subsequent polishing-driven ligand exchange process removes imperfect surface sites and replaces initial long-chain organic ligands with short-chain benzene ligands. The resulting QDs exhibit high photoluminescence quantum yield (PLQY) to near-unity. The resulting PeLEDs exhibit a pure-blue electroluminescence (EL) emission at 472 nm with narrow full-width at half-maximum (FWHM) of 25 nm, achieving a maximum EQE of 10.7% and a bright maximum luminance of 7697 cd m-2. The pure-blue PeLEDs show ultrahigh spectral stability under high voltage, a low roll-off of EQE, and an operational half-lifetime (T50) of 127 min at an initial luminance of 103 cd m-2 under continuous operation.

Enhanced Efficiency and Stability of Sky Blue Perovskite Light-Emitting Diodes via Introducing Lead Acetate.

All-inorganic metal halide perovskite is promising for highly efficient and thermally stable perovskite light-emitting diodes (PeLEDs). However, there is still great room for improvement in the film quality, including low coverage and high trap density, which play a vital role in achieving high-efficiency PeLEDs. In this work, lead acetate (Pb(Ac)2) was introduced into the perovskite precursor solution as an additive. Experimental results show that perovskite films deposited from a one-step anti-solvent free solution process with increased surface coverage and reduced trap density were obtained, leading to enhanced photoluminescence (PL) intensity. More than that, the valence band maximum (VBM) of perovskite films was reduced, bringing about a better energy level matching the work function of the hole-injection layer (HIL) poly (3,4-ethylenedioxythiophene)-poly (styrene sulfonate) (PEDOT: PSS), which is facilitated for the hole injection, leading to a decrease in the turn-on voltage (Vth) of PeLEDs from 3.4 V for the control device to 2.6 V. Finally, the external quantum efficiency (EQE) of the sky blue PeLEDs (at 484 nm) increased from 0.09% to 0.66%. The principles of Pb(Ac)2 were thoroughly investigated by using X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR). This work provides a simple and effective strategy for improving the morphology of perovskite and therefore the performance of PeLEDs.

Chemical Reaction Modulated Low-Dimensional Phase Toward Highly Efficient Sky-Blue Perovskite Light-Emitting Diodes.

Blue perovskite light-emitting diodes (PeLEDs) are crucial avenues for achieving full-color displays and lighting based on perovskite materials. However, the relatively low external quantum efficiency (EQE) has hindered their progression towards commercial applications. Quasi-two-dimensional (quasi-2D) perovskites stand out as promising candidates for blue PeLEDs, with optimized control over low-dimensional phases contributing to enhanced radiative properties of excitons. Herein, the impact of organic molecular dopants on the crystallization of various n-phase structures in quasi-2D perovskite films. The results reveal that the highly reactive bis(4-(trifluoromethyl)phenyl)phosphine oxide (BTF-PPO) molecule could effectively restrain the formation of organic spacer cation-ordered layered perovskite phases through chemical reactions, simultaneously passivate those uncoordinated Pb2+ defects. Consequently, the prepared PeLEDs exhibited a maximum EQE of 16.6% (@ 490 nm). The finding provides a new route to design dopant molecules for phase modulation in quasi-2D PeLEDs.

Nucleophilic Reaction-Enabled Chloride Modification on CsPbI3 Quantum Dots for Pure Red Light-Emitting Diodes with Efficiency Exceeding 26 .

High-performance pure red perovskite light-emitting diodes (PeLEDs) with an emission wavelength shorter than 650 nm are ideal for wide-color-gamut displays, yet remain an unprecedented challenge to progress. Mixed-halide CsPb(Br/I)3 emitter-based PeLEDs suffer spectral stability induced by halide phase segregation and CsPbI3 quantum dots (QDs) suffer from a compromise between emission wavelength and electroluminescence efficiency. Here, we demonstrate efficient pure red PeLEDs with an emission centered at 638 nm based on PbClx -modified CsPbI3 QDs. A nucleophilic reaction that releases chloride ions and manipulates the ligand equilibrium of the colloidal system is developed to synthesize the pure red emission QDs. The comprehensive structural and spectroscopic characterizations evidence the formation of PbClx outside the CsPbI3 QDs, which regulates exciton recombination and prevents the exciton from dissociation induced by surface defects. In consequence, PeLEDs based on PbClx -modified CsPbI3 QDs with superior optoelectronic properties demonstrate stable electroluminescence spectra at high driving voltages, a record external quantum efficiency of 26.1 %, optimal efficiency roll-off of 16.0 % at 1000 cd m-2 , and a half lifetime of 7.5 hours at 100 cd m-2 , representing the state-of-the-art pure red PeLEDs. This work provides new insight into constructing the carrier-confined structure on perovskite QDs for high-performance PeLEDs.

High Efficiency Near-Infrared Perovskite Light Emitting Diodes With Reduced Rolling-Off by Surface Post-Treatment.

The rolling-off phenomenon of device efficiency at high current density caused by quenching of luminescence in perovskite light-emitting diodes (PeLED) is challenging to be solved. Here, 2-amino-5-iodopyrazine (AIPZ) is dissolved in a mixed solvent of chlorobenzene (CB)/isopropanol (IPA) (7:3 volume ratio) for surface post-treatment of FAPbI3 perovskite film. The interaction of AIPZ and perovskite surface not only balances the charge injection but also passivates defects to enhance radiative recombination in PeLED. Therefore, the PeLED champion yields peak external quantum efficiency reaching 23.2% at the current density of 45 mA cm-2 with a radiance brightness of 290 W sr-1 m-2 . More importantly, the rolling-off of device efficiency is significantly reduced. The lowest rolling-off devices can maintain 80% of peak EQE (22.1%) at a high current density of 460 mA cm-2 , whereas the control device only retains 25% of the peak EQE value. This work provides an effective strategy to improve performance and reduce the EQE rolling-off of PeLED for practical application.

Glutamine Induced High-Quality Perovskite Film to Improve the Efficiency of NIR Perovskite Light-Emitting Diodes.

Formamidine lead iodide (FAPbI3 ) is an important material for realizing high-performance near-infrared light-emitting diodes (NIR-LEDs). However, due to the uncontrollable growth of solution-processed films which usually causes low coverage, and poor surface morphology, the development of FAPbI3 -based NIR-LEDs is hindered, restraining its potential industrial applications. In this work, by employing glutamine (Gln) in perovskite precursor, the quality of FAPbI3 film is improved significantly. Due to the ameliorated solution process by the organic additive, the film coverage over the substrate is substantially enhanced. Meanwhile, the trap state of grain is largely reduced. Consequently, NIR perovskite LEDs are demonstrated with a maximum external quantum efficiency (EQE) of 15% with the emission peak at 795 nm, which is four times higher than the device with pristine perovskite film.

High Curvature PEDOT:PSS Transport Layer Toward Enhanced Perovskite Light-Emitting Diodes.

The rapidly developed metal halide perovskite light-emitting diodes (PeLEDs) are considered as a promising candidate for next-generation display and illumination, but the unbalanced charge transport is still a hard-treat case to restrict its efficiency and operational stability. Here, a high curvature PEDOT:PSS transport layer is demonstrated via the self-assembly island-like structures by the incorporation of alkali metal salts. Benefiting from the dielectric confinement effect of the high curvature surface, the modified CsPbBr3 -based PeLEDs present a 2.1 times peak external quantum efficiency (EQE) from 6.75% to 14.23% and a 3.3 times half lifetime (T50 ) from 3.96 to 13.01 h. Besides, the PeLEDs show high luminance up to 44834 cd m-2 . Evidently, this work may provide a deep insight into the structure-activity relationship between the micro-structures at the PEDOT:PSS/perovskite interface and the performance of PeLEDs, and crack the codes for ameliorating the performance of PeLEDs via interfacial micro-structured regulation.

Multidentate Molecule Anchoring Halide Perovskite Surface and Regulating Crystallization Kinetics toward Efficient Light-Emitting Diodes.

Functional passivators are conventionally utilized in modifying the crystallization properties of perovskites to minimize the non-radiative recombination losses in perovskite light-emitting diodes (PeLEDs). However, the weak anchor ability of some commonly adopted molecules has limited passivation ability to perovskites and even may desorb from the passivated defects in a short period of time, which bring about plenty of challenges for further development of high-performance PeLEDs. Here, a multidentate molecule, formamidine sulfinic acid (FSA), is introduced as a novel passivator to perovskites. FSA has multifunctional groups (S≐O, C≐N and NH2 ) where the S≐O and C≐N groups enable coordination with the lead ions and the NH2 interacts with the bromide ions, thus providing the most effective chemical passivation for defects and in turn the formation of highly stable perovskite emitters. Moreover, the interaction between the FSA and octahedral [PbBr6 ]4- can inhibit the formation of unfavorable low-n domains to further minimize the inefficient energy transfer inside the perovskite emitters. Therefore, the FSA passivated green-emitting PeLED exhibits a high external quantum efficiency (EQE) of 26.5% with fourfold enhancement in operating lifetime as compared to the control device, consolidating that the multidentate molecule is a promising strategy to effectively and sustainably passivate the perovskites.

Dielectric Regulation for Efficient Top-Emission Perovskite Light-Emitting Diodes with Suppressed Efficiency Roll-off.

Perovskite light-emitting diodes (PeLEDs) have shown incalculable application potential in the fields of next-generation displays and light communication owing to the rapidly increased external quantum efficiencies (EQEs). However, most PeLEDs obtain a maximum EQE at small current density (J) region and suffer from severe efficiency roll-off in different extents. Herein, it is demonstrated that the dopant with large dipole moment like KBF4 facilitates the effective dielectric regulation of perovskite emissive layer. The increased dielectric constant lowers the exciton binding energy and suppresses the Auger recombination of the 2D/3D segregated perovskite structure, which improves the photoluminescence quantum yield remarkably at an excitation intensity up to 103  mW cm-2 . Accordingly, the top-emission PeLED that delivers a high maximum EQE above 20% is fabricated and can retain EQE > 10% at an extremely high J of 708 mA cm-2 . These results represent one of the most efficient top-emission PeLEDs with ultra-low efficiency roll-off, which provide a viable methodology for tuning the dielectric response of perovskite films for improved high radiance performance of perovskite electroluminescence devices.

Improving Crystallinity and Out-of-Plane Orientation in Quasi-2D Ruddlesden-Popper Perovskite by Fluorinated Organic Salt for Light-Emitting Diodes.

Fluoro-substituted aromatic alkylammonium spacer cations are found effective to improve the performance of quasi-2D perovskite light-emitting diodes (PeLEDs). The fluorine substitution is generally attributed to the defect passivation, quantum well width control, and energy level adjustments. However, the substituted cations can also affect the crystallization process but is not thoroughly studied. Herein, a comparison study is carried out using bare PEA cation and three different fluoro-substituted PEA (x-F-PEA, x = o, ortho; m, meta; p, para) cations to investigate the impacts of different substitution sites on the perovskite crystallization and orientations. By using GIWAXS, p-F-PEA cation is found to induce the strongest preferential out-of-plane orientations with the best crystallinity in quasi-2D perovskite. Using dynamic light scattering (DLS) methods, larger colloidal particles (630 nm) are revealed in p-F-PEA precursor solutions than the PEA cations (350 nm). The larger particles can accelerate the crystallization process and induce out-of-plane orientation from increased dipole-dipole interaction. The transient absorption measurement confirms longer radiative recombination lifetime, proving beneficial effect of p-F-PEA cation. As a result, the fabricated p-F-PEA-based PeLEDs achieved the highest EQE of 15.2%, which is higher than those of PEA- (8.8%), o-F-PEA- (4.3%), and m-F-PEA-based (10.3%) PeLEDs.

High-Efficiency Pure-Red Perovskite Quantum-Dot Light-Emitting Diodes.

It is still challenging to achieve high-efficiency pure-red (620-650 nm wavelength) perovskite light-emitting diodes (PeLEDs). Herein, we report pure-red PeLEDs with Commission Internationale de l'Eclairage coordinates (0.703, 0.297) meeting the Rec. 2020, an external quantum efficiency of 20.8%, and a luminance of 3775 cd/m2. This design is based on the strong quantum confinement CsPbI3 quantum dots (QDs) capped by composite ligands of 3-phenyl-1-propylamine and tetrabutylammonium iodide. This strategy stabilized the structure of the strong-confined QDs and reduced the influence of the electric field-induced Stark effect on the PeLEDs. Furthermore, the exciton binding energy of the QDs was decreased by the composited ligands to suppress Auger recombination within the devices. Additionally, the valence-band maximum of the QDs was lifted to match the hole-transport layer, thus balancing charge injection in the PeLEDs. Our device also demonstrated a stable electroluminescence spectrum and a lifetime of 5.6 times longer than the control device.

Conductive Phosphine Oxide Passivator Enables Efficient Perovskite Light-Emitting Diodes.

Recently, surface passivation has been proved to be an essential approach for obtaining efficient and stable perovskite light-emitting diodes (Pero-LEDs). Phosphine oxides performed well as passivators in many reports. However, the most commonly used phosphine oxides are insulators, which may inhibit carrier transport between the perovskite emitter and charge-transporter layers, limiting the corresponding device performance. Here, 2,7-bis(diphenylphosphoryl)-9,9'-spirobifluorene (SPPO13), a conductive molecule with two phosphine oxide functional groups, is introduced to modify the perovskite emitting layer. The bifunctional SPPO13 can passivate the nonradiative defects of perovskite and promote electron injection at the interface of perovskite emitter and electron-transporter layers. As a result, the corresponding Pero-LEDs obtain a maximum external quantum efficiency (EQE) of 22.3%. In addition, the Pero-LEDs achieve extremely high brightness with a maximum of around 190 000 cd/m2.

Manipulating Local Lattice Distortion for Spectrally Stable and Efficient Mixed-halide Blue Perovskite LEDs.

Mixed-halide perovskites are considered the most straightforward candidate to realize blue perovskite light-emitting diodes (PeLEDs). However, they suffer severe halide migration, leading to spectral instability, which is particularly exaggerated in high chloride alloying perovskites. Here, we demonstrate energy barrier of halide migration can be tuned by manipulating the degree of local lattice distortion (LLD). Enlarging the LLD degree to a suitable level can increase the halide migration energy barrier. We herein report an "A-site" cation engineering to tune the LLD degree to an optimal level. DFT simulation and experimental data confirm that LLD manipulation suppresses the halide migration in perovskites. Conclusively, mixed-halide blue PeLEDs with a champion EQE of 14.2 % at 475 nm have been achieved. Moreover, the devices exhibit excellent operational spectral stability (T50 of 72 min), representing one of the most efficient and stable pure-blue PeLEDs reported yet.

Blue Perovskite Nanocrystal Light-Emitting Diodes: Overcoming RuddlesdenPopper Fault-Induced Nonradiative Recombination via Post-Halide Exchange.

Metal halide perovskites (MHPs) have gained traction as emitters owing to their excellent optical properties, such as facile bandgap tuning, defect tolerance, and high color purity. Nevertheless, blue-emitting MHP light-emitting diodes (LEDs) show only marginal progress in device efficiency compared with green and red LEDs. Herein, the origin of the drop in efficiency of blue-emitting perovskite nanocrystals (PNCs) by mixing halides and the genesis of Ruddlesden-Popper faults (RPFs) in CsPbBrX Cl3-X nanocrystals is investigated. Using scanning transmission electron microscopy and density functional theory calculations, the authors have found that RPFs induce possible nonradiative recombination pathways owing to the high chloride vacancy concentration nearby. The authors further confirm that the blue-emitting PNCs do not show RPFs post-halide exchange in the CsPbBr3 nanocrystals. By introducing the post-halide exchange treatment, high-efficiency pure blue-emitting (464 nm) PNC-based LEDs with an external quantum efficiency of 2.1% and excellent spectral stability with a full-width at half-maximum of 14 nm are obtained.

18-Crown-6 Additive to Enhance Performance and Durability in Solution-Processed Halide Perovskite Electronics.

Recently, an "interlayer" has been often adopted in organic-inorganic hybrid perovskite light-emitting diodes (PeLEDs). The term "interlayer" infers that the layer function is not clear, but it improves electroluminescence (EL) performance. In this respect, it is of interest to determine the exact role of the interlayer and how it works in PeLEDs. In this study, the interlayer is determined to play a crucial role in suppressing the chemical reaction between the metal oxide and hybrid perovskite layers. Nevertheless, the use of an interlayer, a wide gap insulator, does not guarantee the best PeLED performance because it hinders charge injection into the emission layer. Here, a method is proposed that does not apply an "interlayer" but enables simultaneous attainment of high EL performance and outstanding device stability. 18-crown 6-ether (18C6) additive (2.5 mg mL-1 ) is found to fully suppress the chemical reaction between the metal oxide and hybrid perovskite layers. With the 18C6 additive, an 82-fold longer device lifetime and very low operating voltage (3.2 V at 10 000 cd m-2 ) are demonstrated in a PeLED.