Vacancy-Induced Symmetry Breaking in Titanium Dioxide Boosts the Photocatalytic Hydrogen Production from Methanol Aqueous Solution.

The key to optimizing photocatalysts lies in the efficient separation and oriented migration of the photogenerated carriers. Herein, we report that breaking continuous TiO6 tetragonal (D4h) symmetry in titanium dioxide material by oxygen vacancy engineering could induce a dipole field within the bulk phase and thus facilitate the separation and transfer of photogenerated electron-hole pairs. After further loading of Cu single-atom co-catalysts, the obtained catalyst attained a hydrogen (H2) yield rate of 15.84 mmol g-1 h-1 and a remarkable apparent quantum yield of 12.67% at 385 nm from methanol aqueous solution. This catalyst also demonstrated impressive stability for at least 24 h during the photocatalytic tests. The innovative concept of producing dipole fields in semiconductors by breaking the crystal symmetry offers a new perspective for designing photocatalysts.

Photobiocidal Activity of TiO2/UHMWPE Composite Activated by Reduced Graphene Oxide under White Light.

Herein, we introduce a photobiocidal surface activated by white light. The photobiocidal surface was produced through thermocompressing a mixture of titanium dioxide (TiO2), ultra-high-molecular-weight polyethylene (UHMWPE), and reduced graphene oxide (rGO) powders. A photobiocidal activity was not observed on UHMWPE-TiO2. However, UHMWPE-TiO2@rGO exhibited potent photobiocidal activity (>3-log reduction) against Staphylococcus epidermidis and Escherichia coli bacteria after a 12 h exposure to white light. The activity was even more potent against the phage phi 6 virus, a SARS-CoV-2 surrogate, with a >5-log reduction after 6 h exposure to white light. Our mechanistic studies showed that the UHMWPE-TiO2@rGO was activated only by UV light, which accounts for 0.31% of the light emitted by the white LED lamp, producing reactive oxygen species that are lethal to microbes. This indicates that adding rGO to UHMWPE-TiO2 triggered intense photobiocidal activity even at shallow UV flux levels.

Green synthesis of Zn-doped TIO2 nanoparticles from Zanthoxylum armatum.

Green synthesis is an easy, safe, and environmentally beneficial nanoparticle creation method. It is a great challenge to simultaneously improve the capping and stabilizing agent carrier separation efficiency of photocatalysts. Herein, Zn-doped Titanium dioxide (TiO2) nanoparticles with high exposure of 360 nm using a UV/visible spectrophotometer were prepared via a one-step hydrothermal decomposition method. A detailed analysis reveals that the electronic structures were modulated by Zn doping; thus, the responsive wavelength was extended to 600 nm, which effectively improved the visible light absorption of TiO2. We have optimized the different parameters like concentration, time, and temperature. The peak for TiO2 is located at 600 cm-1 in FTIR. A scanning electron microscope revealed that TiO2 has a definite shape and morphology. The synthesized Zn-doped TiO2NPs were applied against various pathogens to study their anti-bacterial potentials. The anti-bacterial activity of Zn-doped TiO2 has shown robust against two gram-ve bacteria (Salmonella and Escherichia coli) and two gram + ve bacteria (Staphylococcus epidermidis and Staphylococcus aureus). Synthesized Zn-doped TiO2 has demonstrated strong antifungal efficacy against a variety of fungi. Moreover, doping TiO2 nanoparticles with metal oxide greatly improves their characteristics; as a result, doped metal oxide nanoparticles perform better than doped and un-doped metal oxide nanoparticles. Compared to pure TiO2, Zn-doped TiO2 nanoparticles exhibit considerable applications including antimicrobial treatment and water purification.

Unique properties of titanium dioxide quantum dots assisted regulation of growth and biochemical parameters of Hibiscus sabdariffa plants.

Owing to the uniqueness of quantum dots (QDs) as a potential nanomaterial for agricultural application, hence in the present study, titanium dioxide quantum dots (TiO2 QDs) were successfully synthesized via sol-gel technique and the physico-chemical properties of the prepared TiO2 QDs were analyzed. Based on the results, the TiO2 QDs showed the presence of anatase phase of TiO2. TEM examination revealed spherical QDs morphology with an average size of 7.69 ± 1.22 nm. The large zeta potential value (-20.9 ± 2.3 mV) indicate greater stability of the prepared TiO2 QDs in aqueous solutions. Moreover, in this work, the application of TiO2 QDs on Hibiscus sabdariffa plants was conducted, where H. sabdariffa plants were foliar sprayed twice a week in the early morning with different concentrations of TiO2 QDs (0, 2, 5, 10, 15 and 30 ppm) to evaluate their influence on these plants in terms of morphological indexes and biochemical parameters. The results exhibited an increasing impact of the different used concentrations of TiO2 QDs on morphological indexes, such as fresh weight, dry weight, shoot length, root length, and leaf number, and physio-biochemical parameters like chlorophyll a, chlorophyll b, carotenoid contents, total pigments and total phenolic contents. Remarkably, the most prominent result was recorded at 15 ppm TiO2 QDs where plant height, total protein and enzymatic antioxidants like catalase and peroxidase were noted to increase by 47.6, 20.5, 29.5 and 38.3%, respectively compared to control. Therefore, foliar spraying with TiO2 QDs positively serves as an effective strategy for inducing optimistic effects in H. sabdariffa plants.

Development of a bottom-up coarse-grained model for interactions of lipids with TiO 2 nanoparticles.

Understanding interactions of inorganic nanoparticles with biomolecules is important in many biotechnology, nanomedicine, and toxicological research, however, the size of typical nanoparticles makes their direct modeling by atomistic simulations unfeasible. Here, we present a bottom-up coarse-graining approach for modeling titanium dioxide (TiO 2 ) nanomaterials in contact with phospholipids that uses the inverse Monte Carlo method to optimize the effective interactions from the structural data obtained in small-scale all-atom simulations of TiO 2 surfaces with lipids in aqueous solution. The resulting coarse-grained models are able to accurately reproduce the structural details of lipid adsorption on different titania surfaces without the use of an explicit solvent, enabling significant computational resource savings and favorable scaling. Our coarse-grained simulations show that small spherical TiO 2 nanoparticles ( r = 2 nm) can only be partially wrapped by a lipid bilayer with phosphoethanolamine headgroups, however, the lipid adsorption increases with the radius of the nanoparticle. The current approach can be used to study the effect of the size and shape of TiO 2 nanoparticles on their interactions with cell membrane lipids, which can be a determining factor in membrane wrapping as well as the recently discovered phenomenon of nanoquarantining, which involves the formation of layered nanomaterial-lipid structures.

A systematic DFT study of structure and electronic properties of titanium dioxide.

DFT functionals are of paramount importance for an accurate electronic and structural description of transition metal systems. In this work, a systematic analysis using some well-known and commonly used DFT functionals is performed. A comparison of the structural and energetic parameters calculated with the available experimental data is made in order to find the adequate functional for an accurate description of the TiO2 bulk and surface of both anatase and rutile structures. In the absence of experimental data on the surface energy, the theoretical predictions obtained using the high-accuracy HSE06 functional were used as a reference to compare against the surface energy values calculated with the other DFT functionals. A clear improvement in the electronic description of both anatase and rutile was observed by introducing the Hubbard U correction term to PBE, PW91, and OptPBE functionals. The OptPBE-U4 functional was found to offer a good compromise between accurately describing the structural and electronic properties of titania.

TiO2 Films with Macroscopic Chiral Nematic-Like Structure Stabilized by Copper Promoting Light-Harvesting Capability for Hydrogen Generation.

Cellulose nanocrystals (CNCs) have inspired the synthesis of various advanced nanomaterials, opening opportunities for different applications. However, a simple and robust approach for transferring the long-range chiral nematic nanostructures into TiO2 photocatalyst is still fancy. Herein, a successful fabrication of freestanding TiO2 films maintaining their macroscopic chiral nematic structures after removing the CNCs biotemplate is reported. It is demonstrated that including copper acetate in the sol avoids the epitaxial growth of the lamellar-like structure of TiO2 and stabilizes the chiral nematic structure instead. The experimental results and optical simulation demonstrate an enhancement at the blue and red edges of the Fabry-Pérot reflectance peak located in the visible range. This enhancement arises from the light scattering effect induced by the formation of the chiral nematic structure. The nanostructured films showed 5.3 times higher performance in the photocatalytic hydrogen generation, compared to lamellar TiO2, and benefited from the presence of copper species for charge carriers' separation. This work is therefore anticipated to provide a simple approach for the design of chiral nematic photocatalysts and also offers insights into the electron transfer mechanisms on TiO2/CuxO with variable oxidation states for photocatalytic hydrogen generation.

Glucosylated Hybrid TiO2 /Polymer Nanomaterials for Actively Targeted Sonodynamic Therapy of Cancer.

Sonodynamic therapy (SDT) is an anti-cancer therapeutic strategy based on the generation of reactive oxygen species (ROS) upon local ultrasound (US) irradiation of sono-responsive molecules or nanomaterials that accumulate in the tumor. In this work, the sonodynamic efficiency of sono-responsive hybrid nanomaterials composed of amorphous titanium dioxide and an amphiphilic poly(ethylene oxide)-b-poly(propylene oxide) block copolymer is synthesized, fully characterized, and investigated both in vitro and in vivo. The modular and versatile synthetic pathway enables the control of the nanoparticle size between 30 and 300 nm (dynamic light scattering) and glucosylation of the surface for active targeting of tumors overexpressing glucose transporters. Studies on 2D and 3D rhabdomyosarcoma cell cultures reveal a statistically significant increase in the sonodynamic efficiency of glucosylated hybrid nanoparticles with respect to unmodified ones. Using a xenograft rhabdomyosarcoma murine model, it is demonstrated that by tuning the nanoparticle size and surface features, the tumor accumulation is increased by ten times compared to main off-target clearance organs such as the liver. Finally, the SDT of rhabdomyosarcoma-bearing mice is investigated with 50-nm glucosylated nanoparticles. Findings evidence a dramatic prolongation of the animal survival and tumor volumes 100 times smaller than those treated only with ultrasound or nanoparticles.

Enhanced Light Absorption and Photo-Generated Charge Separation Efficiency for Boosting Photocatalytic H2 Evolution through TiO2 Quantum Dots with N-Doping and Concomitant Oxygen Vacancy.

Low-range light absorption and rapid recombination of photo-generated charge carriers have prevented the occurrence of effective and applicable photocatalysis for decades. Quantum dots (QDs) offer a solution due to their size-controlled photon properties and charge separation capabilities. Herein, well-dispersed interstitial nitrogen-doped TiO2 QDs with stable oxygen vacancies (N-TiO2-x-VO) are fabricated by using a low-temperature, annealing-assisted hydrothermal method. Remarkably, electrostatic repulsion prevented aggregation arising from negative charges accumulated in situ on the surface of N-TiO2-x-VO, enabling complete solar spectrum utilization (200-800 nm) with a 2.5 eV bandgap. Enhanced UV-vis photocatalytic H2 evolution rate (HER) reached 2757 µmol g-1 h-1, 41.6 times higher than commercial TiO2 (66 µmol g-1 h-1). Strikingly, under visible light, HER rate was 189 µmol g-1 h-1. Experimental and simulated studies of mechanisms reveal that VO can serve as an electron reservoir of photo-generated charge carriers on N-doped active sites, and consequently, enhance the separation rate of exciton pairs. Moreover, the negative free energy (-0.35 V) indicates more favorable thermodynamics for HER as compared with bulk TiO2 (0.66 V). This research work paves a new way of developing efficient photocatalytic strategies of HER that are applicable in the sustainable carbon-zero energy supply.

Visible-Light-Responsive Photoreversible Multi-Color Switching for Rewritable Light-Printing and Information Display.

Photoreversible color switching systems (PCSSs) exhibiting multi-color responses to visible light are favored for sustainable societal development over those relying on ultraviolet light due to safer operation and better penetration depth. Here, a PCSS capable of multi-color switching responsive to visible light based on highly photoreductive rutile-phase Sn-doped TiO2-x nanoparticles is reported. The Sn-doping significantly red-shifts the absorption band of the nanoparticles to the visible region, improving charge separation and transfer efficiencies and introducing Ti3+ species and oxygen vacancies as internal sacrificial electron donors for scavenging photogenerated holes. The resulting Sn-doped TiO2-x nanoparticles feature exceptional photoreduction ability and activity, thereby enabling photoreversible color switching of various redox dyes operational under visible light illumination. Furthermore, multi-color switching can be achieved via the color overlay effect by combining different redox dyes in one system, opening the door to many advanced applications, as demonstrated in their successful uses for developing visible-light-driven rewritable multi-color light-printing systems and visual information displays.

Anchoring Carbon Spheres on Titanium Dioxide Modified Commercial Polyethylene (PE) Separator to Suppress Lithium Dendrites for Lithium Metal Batteries.

Lithium dendrites are easily generated for excessively-solved lithium ions (Li+) inside the lithium metal batteries, which will lead serious safety issues. In this experiment, carbon spheres (CS) are successfully anchored on TiO2 (CS@TiO2) in the hydrothermal polymerization, which is filtrated on the commercial PE separator (CS@TiO2@PE). The negative charge in CS can suppress random diffusion of anions through electrostatic interactions. Density functional theory (DFT) calculations show that CS contributes to the desolvation of Li+, thereby increasing the migration rate of Li+. Furthermore, TiO2 exhibits high affinity to liquid electrolytes and acts as a physical barrier to lithium dendrite formation. CS@TiO2 is a combination of the advantages of CS and TiO2. As results, the Li+ transference number of the CS@TiO2@PE separator can be promoted to 0.63. The Li||Li cell with the CS@TiO2@PE separator exhibits a stable cycle performance for more than 600 h and lower polarization voltage (17 mV) at 1 mA cm-2. The coulombic efficiency (CE) of the Li||Cu cells employe the CS@TiO2@PE separator is 81.63% over 130 cycles. The discharge capacity of LiFePO4||Li cells based on the CS@TiO2@PE separator is 1.73 mAh (capacity retention = 91.53% after 260 cycles). Thus, the CS@TiO2 layer inhibits lithium dendrite formation.

The enhanced antibacterial and antibiofilm properties of titanium dioxide nanoparticles biosynthesized by multidrug-resistant Pseudomonas aeruginosa.

The emergence of Multidrug-resistant (MDR) bacteria are becoming a major worldwide health concern, encouraging the development effective alternatives to conventional antibiotics. The study identified P. aeruginosa and assessed its antimicrobial sensitivity using the Vitek-2 system. Carbapenem-resistant genes were detected through Polymerase chain reaction (PCR). MDR- P. aeruginosa isolates were used to biosynthesize titanium dioxide nanoparticles (TiO2NPs) and characterized using X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM), field emission scanning electron microscopy (FE-SEM). A study involving 78 P. aeruginosa isolates revealed that 85.8% were MDR, with meropenem and amikacin showing effectiveness against 70% of the isolates. The most prevalent carbapenemase gene was blaOXA-48, present in 83% of the isolates. Majority of the isolates formed biofilms, and biosynthesized TiO2NPs were able to reduce biofilm formation by 94%. TiO2NPs exhibited potent antibacterial action against MDR-Gram-negative bacilli pathogens and showed synergistic activity with antibiotics, particularly piperacillin, with a significant fold increase in areas (283%). A new local strain of P. aeruginosa, identified as ON678251 in the World GenBank, was found capable of producing TiO2NPs. Our findings demonstrate the potential of biosynthesized TiO2NPs to manage antibiotic resistance and regulate the formation of biofilms. This presents a promising direction for the creation of novel antimicrobial agents or substitutes for use in clinical settings, particularly in the management of isolates capable of resisting multiple drugs.

Glycerol Oligomerization over Titania-Based Catalyst Compositions.

The possibility of using TiO2 -based compositions: individual and sulfated titania, and their composites with carbon nanotubes as catalysts for glycerol oligomerization has been displayed. The effect of modification of TiO2 with sulfur and carbon nanotubes on acid-base and catalytic characteristics in the glycerol conversion was investigated. The activation of glycerol on the catalysts has been studied using attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy. Only the samples based on sulfated titania are active over glycerol transformation, showing up to 58.7 % conversion. This is explained by the presence of strong base sites. Glycerides up to pentaglycerides, both linear and nonlinear structure are formed by glycerol oligomerization over TiO2 -S. The addition of nanotubes to the catalyst reduces both the glycerol conversion (up to 10.5 %) and the yield of glycerides. However, the spectrum of the resulting products is significantly narrowed, increasing the selectivity for short-chain glycerides: the portion of diglycerides reaches 72 %, and triglycerides 21 %. Herewith, glycerides of a linear structure only formed.

Nanoparticle-based nanocomposite coatings with postprocessing for enhanced antimicrobial capacity of polymeric film.

Bacterial adhesion and biofilm formation on surfaces pose a significant risk of microbial contamination and chronic diseases, leading to potential health complications. To mitigate this concern, the implementation of antibacterial coatings becomes paramount in reducing pathogen propagation on contaminated surfaces. To address this requirement, our study focuses on developing cost-effective and sustainable methods using polymer composite coatings. Copper and titanium dioxide nanoparticles were used to assess their active antimicrobial functions. After coating the surface with nanoparticles, four different combinations of two postprocessing treatments were performed. Intense pulsed light was utilized to sinter the coatings further, and plasma etching was applied to manipulate the physical properties of the nanocomposite-coated sheet surface. Bacterial viability was comparatively analyzed at four different time points (0, 30, 60, and 120 min) upon contact with the nanocomposite coatings. The samples with nanoparticle coatings and postprocessing treatments showed an above-average 84.82% mortality rate at 30 min and an average of 89.77% mortality rate at 120 min of contact. In contrast, the control sample, without nanoparticle coatings and postprocessing treatments, showed a 95% microbe viability after 120 min of contact. Through this study, we gained critical insights into effective strategies for preventing the spread of microorganisms on high-touch surfaces, thereby contributing to the advancement of sustainable antimicrobial coatings.

Biomedical application of TiO2NPs can cause arterial thrombotic risks through triggering procoagulant activity, activation and aggregation of platelets.

BACKGROUND: Titanium dioxide nanoparticles (TiO2NPs) are widely used in medical application. However, the relevant health risk has not been completely assessed, the potential of inducing arterial thrombosis (AT) in particular. METHODS: Alterations in platelet function and susceptibility to arterial thrombosis induced by TiO2NPs were examined using peripheral blood samples from healthy adult males and an in vivo mouse model, respectively. RESULTS: Here, using human platelets (hPLTs) freshly isolated from health volunteers, we demonstrated TiO2NP treatment triggered the procoagulant activity of hPLTs through phosphatidylserine exposure and microvesicles generation. In addition, TiO2NP treatment increased the levels of glycoprotein IIb/IIIa and P-selectin leading to aggregation and activation of hPLTs, which were exacerbated by providing physiology-mimicking conditions, including introduction of thrombin, collagen, and high shear stress. Interestingly, intracellular calcium levels in hPLTs were increased upon TiO2NP treatment, which were crucial in TiO2NP-induced hPLT procoagulant activity, activation and aggregation. Moreover, using mice in vivo models, we further confirmed that TiO2NP treatment a reduction in mouse platelet (mPLT) counts, disrupted blood flow, and exacerbated carotid arterial thrombosis with enhanced deposition of mPLT. CONCLUSIONS: Together, our study provides evidence for an ignored health risk caused by TiO2NPs, specifically TiO2NP treatment augments procoagulant activity, activation and aggregation of PLTs via calcium-dependent mechanism and thus increases the risk of AT.

CdSe nanostructured thin film by electrophoretic deposition for quantum dots sensitized solar cell.

Cadmium selenide (CdSe) quantum dots (QDs) with different size, 2.5 and 3.2 nm, were successfully deposited on mesoporous titanium dioxide (TiO2) (Degussa-P25) nanostructures by electrophoretic deposition method (EPD) at the applied voltage 100 V for 120 s deposition time. In this study, the morphology of CdSe films deposited by EPD and the performance of the film when assembled into a solar cell were investigated. From the field emission scanning electron microscopy cross-section, the thickness of the CdSe nanoparticles with size 2.5 nm films were 3.4 and 3.0µm for CdSe 3.2 nm nanoparticles film. The structure of 2.5 nm is denser than compare of 3.2 nm CdSe nanoparticles. From UV visible spectroscopy, the band gap calculated for 2.5 nm CdSe nanoparticles is 2.28 eV and for 3.2 nm is 2.12 eV. Photovoltaic characterization was performed under an illumination of 100 mW cm-2. A photovoltaic conversion efficiency of 1.81% was obtained for 2.5 nm CdSe and 2.1% was obtained for 3.2 nm CdSe nanoparticles. This result shows that the photovoltaic efficiency is dependent on CdSe nanoparticle size.

Density functional theory for doped TiO2: current research strategies and advancements.

Since the inception of the density functional theory (DFT) by Hohenberg and Kohn in 1964, it rapidly became an indispensable theoretical tool across various disciplines, such as chemistry, biology, and materials science, among others. This theory has ushered in a new era of computational research, paving the way for substantial advancements in fundamental understanding. Today, DFT is routinely employed for a diverse range of applications, such as probing new material properties and providing a profound understanding of the mechanisms underlying physical, chemical, and biological processes. Even after decades of active utilization, the improvement of DFT principles has never been slowed down, meaning that more accurate theoretical results are continuously generated with time. This work highlights the latest achievements acquired by DFT in the specific research field, namely the theoretical investigations of doped TiO2systems, which have not been comprehensively reviewed and summarized yet. Successful progress in this niche is currently hard to imagine without the support by DFT. It can accurately reveal new TiO2properties after introducing the desired dopant and help to find the optimal system design for a specific application prior to proceeding to more time-consuming and expensive experimental research. Hence, by evaluating a selection of the most recent research studies, we aim to highlight the pertinent aspects of DFT as they relate to the study of doped TiO2systems. We also aim to shed light on the strengths and weaknesses of DFT and present the primary strategies employed thus far to predict the properties of various doped TiO2systems reliably.

Plasmonic effect of metal nanoparticles on the photocatalytic properties of TiO2/rGO composite.

A comparative study of the plasmon effect of Ag and Au nanoparticles on TiO2/rGO nanocomposite was carried out. The synthesis of Au and Ag nanoparticles was carried out by laser ablation. The morphology and structure of the nanocomposites were studied by EDA, HRTEM, XRD and Raman spectroscopy. It was shown that the absorption capacity of the nanocomposite material was increased in the visible range of the spectrum when Ag and Au nanoparticles were added to TiO2/rGO. This leads to an increase in their photocatalytic activity. The photocurrent generated by NC/Au 10-11films is in 3.8 times and NC/Ag 10-12is in 2 times higher compared to pure TiO2/rGO film. Similar results were obtained from experimental data on the dyes photodegradation. In the presence of plasmon nanoparticles a significant enhancement in the electrical properties of the TiO2/rGO nanocomposite was recorded. The charge carrier transfer resistance in nanocomposites was decreased by almost ∼7 times for NC/Au,10-11and ∼4 times for NC/Ag,10-12films compared to pure TiO2/rGO. In addition, for nanocomposites with Ag or Au nanoparticles, a decrease in the effective electron lifetime was observed. The data obtained allow us to conclude that plasmonic NPs have a synergistic effect in TiO2/rGO nanocomposites, which consists in modifying both their light-harvesting properties and charge-transport characteristics. The results obtained can be used for the design of materials with improved photocatalytic and optoelectronic characteristics.

Prediction of Nanoparticle Photoreactivity in Mixtures of Surface Foulants Requires Kinetic (Non-equilibrium) Adsorption Considerations.

The adsorption of foulants on photocatalytic nanoparticles can suppress their reactivity in water treatment applications by scavenging reactive species at the photocatalyst surface, screening light, or competing for surface sites. These inhibitory effects are commonly modeled using the Langmuir-Hinshelwood model, assuming that adsorbed layer compositions follow Langmuirian (equilibrium) competitive adsorption. However, this assumption has not been evaluated in complex mixtures of foulants. This study evaluates the photoreactivity of titanium dioxide (TiO2) nanoparticles toward a target compound, phenol, in the presence of two classes of foulants ─ natural organic matter (NOM) and a protein, bovine serum albumin (BSA) ─ and mixtures of the two. Langmuir adsorption models predict that BSA should strongly influence the nanoparticle photoreactivity because of its higher adsorption affinity relative to phenol and NOM. However, model evaluation of the experimental phenol decay rates suggested that neither the phenol nor foulant surface coverages are governed by Langmuirian competitive adsorption. Rather, a reactivity model incorporating kinetic predictions of adsorbed layer compositions (favoring NOM adsorption) outperformed Langmuirian models in providing accurate, unbiased predictions of phenol degradation rates. This research emphasizes the importance of using first-principles models that account for adsorption kinetics when assumptions of equilibrium adsorption do not apply.

Dissecting the Photochemical Reactivity of Metal Ions during Atmospheric Nitrate Transformations on Photoactive Mineral Dust.

Dissecting the photochemical reactivity of metal ions is a significant contribution to understanding secondary pollutant formation, as they have a role to be reckoned with atmospheric chemistry. However, their photochemical reactivity has received limited attention within the active nitrogen cycle, particularly at the gas-solid interface. In this study, we delve into the contribution of magnesium ion (Mg2+) and ferric ion (Fe3+) to nitrate decomposition on the surface of photoactive mineral dust. Under simulated sunlight irradiation, the observed NOX production rate differs by an order of magnitude in the presence of Mg2+ (6.02 × 10-10 mol s-1) and Fe3+ (2.07 × 10-11 mol s-1). The markedly decreased fluorescence lifetime induced by Mg2+ and the change in the valence of Fe3+ revealed that Mg2+ and Fe3+ significantly affect the concentration of nitrate decomposition products by distinct photochemical reactivity with photogenerated electrons. Mg2+ promotes NOX production by accelerating charge transfer, while Fe3+ hinders nitrate decomposition by engaging in a redox cyclic reaction with Fe2+ to consume photogenerated carriers continuously. Furthermore, when Fe3+ coexists with other metal ions (e.g., Mg2+, Ca2+, Na+, and K+) and surpasses a proportion of approximately 12%, the photochemical reactivity of Fe3+ tends to be dominant in depleting photogenerated electrons and suppressing nitrate decomposition. Conversely, below this threshold, the released NOX concentration increases sharply as the proportion of Fe3+ decreases. This research offers valuable insights into the role of metal ions in nitrate transformation and the generation of reactive nitrogen species, contributing to a deep understanding of atmospheric photochemical reactions.