RESUMEN
Recently, there has been a notable surge in interest regarding reclaiming valuable chemicals from waste plastics. However, the energy-intensive conventional thermal catalysis does not align with the concept of sustainable development. Herein, we report a sustainable electrocatalytic approach allowing the selective synthesis of glycolic acid (GA) from waste polyethylene terephthalate (PET) over a Pd67Ag33 alloy catalyst under ambient conditions. Notably, Pd67Ag33 delivers a high mass activity of 9.7 A mgPd-1 for ethylene glycol oxidation reaction (EGOR) and GA Faradaic efficiency of 92.7 %, representing the most active catalyst for selective GA synthesis. In situ experiments and computational simulations uncover that ligand effect induced by Ag incorporation enhances the GA selectivity by facilitating carbonyl intermediates desorption, while the lattice mismatch-triggered tensile strain optimizes the adsorption of *OH species to boost reaction kinetics. This work unveils the synergistic of strain and ligand effect in alloy catalyst and provides guidance for the design of future catalysts for PET upcycling. We further investigate the versatility of Pd67Ag33 catalyst on CO2 reduction reaction (CO2RR) and assemble EGOR//CO2RR integrated electrolyzer, presenting a pioneering demonstration for reforming waste carbon resource (i.e., PET and CO2) into high-value chemicals.
RESUMEN
Current un-sustainable plastic management is exacerbating plastic pollution, an urgent shift is thus needed to create a recycling society. Such recovering carbon (C) and hydrogen (H) from waste plastic has been considered as one practical route to achieve a circular economy. Here, we performed a simple pyrolysis-catalysis deconstruction of waste plastic via a monolithic multilayer stainless-steel mesh catalyst to produce multiwalled carbon nanotubes (MWCNTs) and H2, which are important carbon material and energy carrier to achieve sustainable development. Results revealed that the C and H recovery efficiencies were as high as 86% and 70%, respectively. The unique oxidation-reduction process and improvement of surface roughness led to efficient exposure of active sites, which increased MWCNTs by suppressing macromolecule hydrocarbons. The C recovery efficiency declined by only 5% after 10 cycles, proving the long-term employment of the catalyst. This catalyst can efficiently convert aromatics to MWCNTs by the vapor-solid-solid mechanism and demonstrate good universality in processing different kinds of waste plastics. The produced MWCNTs showed potential in applications of lithium-ion batteries and telecommunication. Owing to the economic profits and environmental benefits of the developed route, we highlighted its potential as a promising alternative to conventional incineration, simultaneously achieving the waste-to-resource strategy and circular economy.
RESUMEN
Plastic waste represents one of the most urgent environmental challenges facing humankind. Upcycling has been proposed to solve the low profitability and high market sensitivity of known recycling methods. Existing upcycling methods operate under energy-intense conditions and use precious-metal catalysts, but produce low-value oligomers, monomers, and common aromatics. Herein, we report a tandem degradation-upcycling strategy to exploit high-value chemicals from polystyrene (PS) waste with high selectivity. We first degrade PS waste to aromatics using ultraviolet (UV) light and then valorize the intermediate to diphenylmethane. Low-cost AlCl3 catalyzes both the reactions of degradation and upcycling at ambient temperatures under atmospheric pressure. The degraded intermediates can advantageously serve as solvents for processing the solid plastic wastes, forming a self-sustainable circuitry. The low-value-input and high-value-output approach is thus substantially more sustainable and economically viable than conventional thermal processes, which operate at high-temperature, high-pressure conditions and use precious-metal catalysts, but produce low-value oligomers, monomers, and common aromatics. The cascade strategy is resilient to impurities from plastic waste streams and is generalizable to other high-value chemicals (e.g., benzophenone, 1,2-diphenylethane, and 4-phenyl-4-oxo butyric acid). The upcycling to diphenylmethane was tested at 1-kg laboratory scale and attested by industrial-scale techno-economic analysis, demonstrating sustainability and economic viability without government subsidies or tax credits.
Asunto(s)
Poliestirenos , Reciclaje , Eliminación de Residuos , Plásticos/síntesis química , Poliestirenos/química , Eliminación de Residuos/métodos , SolventesRESUMEN
The increasing demand for personal protective equipment such as single-use masks has led to large amounts of nondegradable plastic waste, aggravating economic and environmental burdens. This study reports a simple and scalable approach for upcycling waste masks via a chemical vapor deposition technique, realizing a trichome-like biomimetic (TLB) N95 respirator with superhydrophobicity (water contact angle ≥150°), N95-level protection, and reusability. The TLB N95 respirator comprising templated silicone nanofilaments with an average diameter of â¼150 nm offers N95-level protection and breathability comparable to those of commercial N95 respirators. The TLB N95 respirator can still maintain its N95-level protection against particulate matter and viruses after 10 disinfection treatment cycles (i.e., ultraviolet irradiation, microwave irradiation, dry heating, and autoclaving), demonstrating durable reusability. The proposed strategy provides new insight into upcycle waste masks, breaking the existing design and preparation concept of reusable masks.
Asunto(s)
COVID-19 , Dispositivos de Protección Respiratoria , Humanos , Respiradores N95 , Máscaras , SARS-CoV-2RESUMEN
Organic aerogels are emerging as promising materials due to their versatile properties, rendering them excellent candidates for a variety of applications in the fields of thermal insulation, energy storage, pharmaceuticals, chemical adsorption, and catalysis. However, current aerogel designs rely on cross-linked polymer networks, which lack efficient end-of-use solutions, thereby hindering their overall sustainability. In this study, a facile synthesis of organic aerogels with a unique combination of imine and cyanurate moieties is presented, resulting in high-performance, lightweight insulating materials. The aerogels' structure, ensures mechanical robustness, thermal resistance, and hydrophobicity without additional treatments, crucial for long-term performance. Additionally, in response to the currently unsustainable use of cross-linked polymer materials, the molecular design offers diverse avenues of chemical recycling. These include full depolymerization back into the original monomers, partial network fragmentation producing soluble oligomers that can be promptly employed to fabricate new aerogels, and upcycling of aerogel waste into useful building blocks. This work pioneers a novel approach to material design, emphasizing recyclability as a core feature while maintaining high-performance excellence.
RESUMEN
Plastics are widely used in daily lives, but unfortunately, their inadequate recycling practices have led to the accumulation of microplastics in the environment, posing a threat to public health. The existing methods for treating microplastics are energy-intensive and environmentally damaging. In this context, photoreforming has emerged as a sustainable solution to address the microplastic crisis by simultaneously recycling them into value-added chemicals. This review presents a comprehensive overview of the application of photoreforming for upcycling microplastic. The underlying mechanisms of photoreforming reaction are discussed, followed by the exploration of recent advancements and innovative strategies in photoreforming techniques with particular emphasis on their real-world applications and potential for large-scale implementation. Also, critical factors influencing the efficiency of microplastic photoreforming are identified, providing guidance for further research and optimization.
RESUMEN
Electrochemical upcycling of nitrate and polyester plastic into valuable products is an ideal solution to realize the resource utilization. Here, the co-production of ammonia (NH3) and glycolic acid (GA) via electrochemical upcycling of nitrate and polyethylene terephthalate (PET) plastics over mesoporous Pd3Au film on Ni foam (mPd3Au/NF), which is synthesized by micelle-assisted replacement method, is proposed. The mPd3Au/NF with well-developed mesoporous structure provides abundant active sites and facilitated transfer channels and strong electronic effect. As such, the mPd3Au/NF exhibits high Faraday efficiencies of 97.28% and 95.32% at 0.9 V for the formation of NH3 and GA, respectively. Theoretical results indicate that the synergistic effect of Pd and Au can optimize adsorption energy of key intermediates *NOH and *OCH2-CH2OH on active sites and increase bond energy of CâC band, thereby improving the activity and selectivity for the formation of NH3 and GA. This work proposes a promising strategy for the simultaneous conversation of nitrate and PET plastic into high-value NH3 and GA.
RESUMEN
With ever-increasing requirements for cathodes in the lithium-ion batteries market, an efficiency and eco-friendly upcycling regeneration strategy is imperative to meet the demand for high-performance cathode materials. Herein, a facile, direct and upcycling regeneration strategy is proposed to restore the failed LiCoO2 and enhance the stability at 4.6 V. Double effects combination of relithiation and outside surface reconstruction are simultaneously achieved via a facile solid-phase sintering method. The evolution process of the Li-supplement and grain-recrystallization is systematically investigated, and the high performance of the upcycled materials at high voltage is comprehensively demonstrated. Thanks to the favorable spinel LiCoxMn2-xO4 surface coating, the upcycled sample displays outstanding electrochemical performance, superior to the pristine cathode materials. Notably, the 1% surface-coated LiCoO2 achieves a high discharge-specific capacity of 207.9 mA h g-1 at 0.1 C and delivers excellent cyclability with 77.0% capacity retention after 300 cycles. Significantly, this in situ created spinel coating layer can be potentially utilized for recycling spent LiCoO2, thus providing a viable, promising recycling strategy insights into the upcycling of degraded cathodes.
RESUMEN
Multiresponsive materials with reversible and durable characteristics are indispensable because of their promising applications in environmental change detections. To fabricate multiresponsive materials in mass production, however, complex reactions and impractical situations are often involved. Herein, a dual responsive (light and pH) spiropyran-based smart sensor fabricated by a simple layer-by-layer (LbL) assembly process from upcycled thermoplastic polyester elastomer (TPEE) materials derived from recycled polyethylene terephthalate (r-PET) is proposed. Positively charged chitosan solutions and negatively charged merocyanine-COOH (MC-COOH) solutions are employed in the LbL assembly technique, forming the chitosan-spiropyran deposited TPEE (TPEE-CH-SP) film. Upon UV irradiation, the spiropyran-COOH (SP-COOH) molecules on the TPEE-CH-SP film undergo the ring-opening isomerization, along with an apparent color change from colorless to purple, to transform into the MC-COOH molecules. By further exposing the TPEE-CH-MC film to hydrogen chloride (HCl) and nitric acid (HNO3) vapors, the MC-COOH molecules can be transformed into protonated merocyanine-COOH (MCH-COOH) with the simultaneous color change from purple to yellow.
RESUMEN
Upgrading thermosetting polymer waste and harvesting unwanted electromagnetic energy are of great significance in solving environmental pollution and energy shortage problems. Herein, inspired by the glass-blowing art, a spontaneous, controllable, and scalable strategy is proposed to prepare hollow carbon materials by inner blowing and outside blocking. Specifically, hierarchically neuron-like hollow carbon materials (HCMSs) with various sizes are fabricated from melamine-formaldehyde sponge (MS) waste. Benefiting from the synergistic of the hollow "cell body" and the connected "protrusions" networks, HCMSs reveal superior electromagnetic absorption performance with a strong reflection loss of -54.9 dB, electromagnetic-heat conversion ability with a high conversion efficiency of 34.4%, and efficient energy storage performance in supercapacitor. Furthermore, a multifunctional device integrating electromagnetic-heat-electrical energy conversion is designed, and its feasibility is proved by experiments and theoretical calculations. The integrated device reveals an output voltage of 34.5 mV and a maximum output power of 0.89 µW with electromagnetic radiation for 60 s. This work provides a novel solution to recycle polymer waste, electromagnetic energy, and unwanted thermal energy.
RESUMEN
Electrocatalytic nitrate reduction reaction (NO3 RR) is a promising approach for converting nitrate into environmentally benign or even value-added products such as ammonia (NH3 ) using renewable electricity. However, the poor understanding of the catalytic mechanism on metal-based surface catalysts hinders the development of high-performance NO3 RR catalysts. In this study, the NO3 RR mechanism of single-atom catalysts (SACs) is systematically explored by constructing single transition metal atoms supported on MXene with oxygen vacancies (Ov -MXene) using density functional theory (DFT) calculations. The results indicate that Ag/Ov -MXene (for precious metal) and Cu/Ov -MXene (for non-precious metal) are highly efficient SACs for NO3 RR toward NH3 , with low limiting potentials of -0.24 and -0.34 V, respectively. Furthermore, these catalysts show excellent selectivity toward ammonia due to the high energy barriers associated to the formation of byproducts such as NO2 , NO, N2 O, and N2 on Ag/Ov -MXene and Cu/Ov -MXene, effectively suppressing the competitive hydrogen evolution reaction (HER). The findings not only offer new strategies for promoting NH3 production by MXene-based SACs electrocatalysts under ambient conditions but also provide insights for the development of next-generation NO3 RR electrocatalysts.
RESUMEN
Cyclohexanone oxime is an important intermediate in the chemical industry, especially for the manufacture of nylon-6. The traditional cyclohexanone oxime production strongly relies on cyclohexanone-hydroxylamine and cyclohexanone ammoxidation processes, which require harsh reaction conditions and consume considerable amounts of energy. Herein, direct electrosynthesis of cyclohexanone oxime is reported from environmental pollutants nitrite and cyclohexanone with almost 100% yield by using low-cost Cu2Se nanosheets as electrocatalysts. Combination of in situ Fourier transform infrared spectroscopy and theoretical calculations verifies that the p-d orbital hybridization between Cu and Se elements could synergistically optimize the surface electronic structure and enable improved adsorption and formation of the key active N intermediate NH2OH*, thereby enhancing cyclohexanone/nitrite-to-cyclohexanone oxime conversion over the Cu2Se nanosheets. Based on these, an efficient asymmetric co-electrolysis system is further demonstrated by coupling cyclohexanone/nitrite-to-cyclohexanone oxime conversion with the upcycling of polyethylene terephthalate plastics, achieveing energy-saving simultaneously production of value-added products (cyclohexanone oxime and glycolic acid).
RESUMEN
Plastic biodegradation has emerged as a sustainable approach and green alternative in handling the ever-increasing accumulation of plastic wastes in the environment. The complete biodegradation of polyethylene terephthalate is one of the most recent breakthroughs in the field of plastic biodegradation. Despite the success, the effective and complete biodegradation of a wide variety of plastics is still far from the practical implementation, and an on-going effort has been mainly devoted to the exploration of novel microorganisms and enzymes for plastic biodegradation. However, alternative strategies which enhance the existing biodegradation process should not be neglected in the continuous advancement of this field. Thus, this review highlights various strategies which have shown to improve the biodegradation of plastics, which include the pretreatment of plastics using UV irradiation, thermal, or chemical treatments to increase the susceptibility of plastics toward microbial action. Alternative pretreatment strategies are also suggested and compared with the existing techniques. Besides, the effects of additives such as pro-oxidants, natural polymers, and surfactants on plastic biodegradation are discussed. In addition, considerations governing the biodegradation performance, such as the formulation of biodegradation medium, cell-free biocatalysis, and physico-chemical properties of plastics, are addressed. Lastly, the challenges and future prospects for the advancement of plastic biodegradation are also highlighted.
Asunto(s)
Plásticos , Polímeros , Plásticos/química , Plásticos/metabolismo , Polímeros/metabolismo , Biodegradación Ambiental , BiocatálisisRESUMEN
Heme, an iron-containing tetrapyrrole in hemoproteins, including: hemoglobin, myoglobin, catalase, cytochrome c, and cytochrome P450, plays critical physiological roles in different organisms. Heme-derived chemicals, such as biliverdin, bilirubin, and phycocyanobilin, are known for their antioxidant and anti-inflammatory properties and have shown great potential in fighting viruses and diseases. Therefore, more and more attention has been paid to the biosynthesis of hemoproteins and heme derivatives, which depends on the adequate heme supply in various microbial cell factories. The enhancement of endogenous biosynthesis and exogenous uptake can improve the intracellular heme supply, but the excess free heme is toxic to the cells. Therefore, based on the heme-responsive regulators, several sensitive biosensors were developed to fine-tune the intracellular levels of heme. In this review, recent advances in the: biosynthesis, acquisition, regulation, and upcycling of heme were summarized to provide a solid foundation for the efficient production and application of high-value-added hemoproteins and heme derivatives.
RESUMEN
Plastic pollution constitutes an evergrowing urgent environmental problem, since overaccumulation of plastic waste, arising from the immense increase of the production of disposable plastic products, overcame planet's capacity to properly handle them. Chemical upcycling of polystyrene constitutes a convenient method for the conversion of plastic waste into high-added value chemicals, suggesting an attractive perspective in dealing with the environmental crisis. We demonstrate herein a novel, easy-to-perform organocatalytic photoinduced aerobic protocol, which proceeds via synergistic indirect hydrogen atom transfer (HAT) catalysis under LED 390â nm Kessil lamps as the irradiation source. The developed method employs a BrCH2CN-thioxanthone photocatalytic system and was successfully applied to a variety of everyday-life plastic products, leading to the isolation of benzoic acid after simple base-acid work up in yields varying from 23-49 %, while a large-scale experiment was successfully performed, suggesting that the photocatalytic step is susceptible to industrial application.
RESUMEN
Bio-upcycling of plastics is an emerging alternative process that focuses on extracting value from a wide range of plastic waste streams. Such streams are typically too contaminated to be effectively processed using traditional recycling technologies. Medium-chain-length (mcl) diols and dicarboxylates (DCA) are major products of chemically or enzymatically depolymerized plastics, such as polyesters or polyethers. In this study, we enabled the efficient metabolism of mcl-diols and -DCA in engineered Pseudomonas putida as a prerequisite for subsequent bio-upcycling. We identified the transcriptional regulator GcdR as target for enabling metabolism of uneven mcl-DCA such as pimelate, and uncovered amino acid substitutions that lead to an increased coupling between the heterologous ß-oxidation of mcl-DCA and the native degradation of short-chain-length DCA. Adaptive laboratory evolution and subsequent reverse engineering unravelled two distinct pathways for mcl-diol metabolism in P. putida, namely via the hydroxy acid and subsequent native ß-oxidation or via full oxidation to the dicarboxylic acid that is further metabolized by heterologous ß-oxidation. Furthermore, we demonstrated the production of polyhydroxyalkanoates from mcl-diols and -DCA by a single strain combining all required metabolic features. Overall, this study provides a powerful platform strain for the bio-upcycling of complex plastic hydrolysates to polyhydroxyalkanoates and leads the path for future yield optimizations.
Asunto(s)
Polihidroxialcanoatos , Pseudomonas putida , Pseudomonas putida/genética , Pseudomonas putida/metabolismo , Poliésteres/metabolismo , Ácidos Carboxílicos/metabolismo , Oxidación-ReducciónRESUMEN
Plastic waste has emerged as a serious issue due to its impact on environmental degradation and resource scarcity. Plastic recycling, especially of halogen-containing plastics, presents challenges due to potential secondary pollution and lower-value implementations. Chemical recycling via pyrolysis is the most versatile and robust approach for combating plastic waste. In this Review, we present recent advancements in halogen-plastic pyrolysis for resource utilization and the potential pathways from "reducing to recycling to upcycling" halogens. We emphasize the advanced management of halogen-plastics through copyrolysis with solid wastes (waste polymers, biomass, coal, etc.), which is an efficient method for dealing with mixed wastes to obtain high-value products while reducing undesirable substances. Innovations in catalyst design and reaction configurations for catalytic pyrolysis are comprehensively evaluated. In particular, a tandem catalysis system is a promising route for halogen removal and selective conversion of targeted products. Furthermore, we propose novel insights regarding the utilization and upcycling of halogens from halogen-plastics. This includes the preparation of halogen-based sorbents for elemental mercury removal, the halogenation-vaporization process for metal recovery, and the development of halogen-doped functional materials for new materials and energy applications. The reutilization of halogens facilitates the upcycling of halogen-plastics, but many efforts are needed for mutually beneficial outcomes. Overall, future investigations in the development of copyrolysis and catalyst-driven technologies for upcycling halogen-plastics are highlighted.
Asunto(s)
Halógenos , Plásticos , Plásticos/química , Pirólisis , Reciclaje , Residuos SólidosRESUMEN
Arsenic (As)-bearing Fe(III) precipitate groundwater treatment sludge has traditionally been viewed by the water sector as a disposal issue rather than a resource opportunity, partly due to assumptions of the low value of As. However, As has now been classified as a Critical Raw Material (CRM) in many regions, providing new incentives to recover As and other useful components of the sludge, such as phosphate (P) and the reactive hydrous ferric oxide (HFO) sorbent. Here, we investigate alkali extraction to separate As from a variety of field and synthetic As-bearing HFO sludges, which is a critical first step to enable sludge upcycling. We found that As extraction was most effective using NaOH, with the As extraction efficiency increasing up to >99% with increasing NaOH concentrations (0.01, 0.1, and 1 M). Extraction with Na2CO3 and Ca(OH)2 was ineffective (<5%). Extraction time (hour, day, week) played a secondary role in As release but tended to be important at lower NaOH concentrations. Little difference in As extraction efficiency was observed for several key variables, including sludge aging time (50 days) and cosorbed oxyanions (e.g., Si, P). However, the presence of â¼10 mass% calcite decreased As release from field and synthetic sludges considerably (<70% As extracted). Concomitant with As release, alkali extraction promoted crystallization of poorly ordered HFO and decreased particle specific surface area, with structural modifications increasing with NaOH concentration and extraction time. Taken together, these results provide essential information to inform and optimize the design of resource recovery methods for As-bearing treatment sludge.
Asunto(s)
Álcalis , Arsénico , Agua Subterránea , Aguas del Alcantarillado , Aguas del Alcantarillado/química , Agua Subterránea/química , Álcalis/química , Contaminantes Químicos del Agua/química , Purificación del Agua/métodos , Compuestos Férricos/químicaRESUMEN
Environmental concerns arising from the increasing use of polluting plastics highlight polylactic acid (PLA) as a promising eco-friendly alternative. PLA is a biodegradable polyester that can be produced through the fermentation of renewable resources. Together with its excellent properties, suitable for a wide range of applications, the use of PLA has increased significantly over the years and is expected to further grow. However, insufficient degradability under natural conditions emphasizes the need for the exploration of biodegradation mechanisms, intending to develop more efficient techniques for waste disposal and recycling or upcycling. Biodegradation occurs through the secretion of depolymerizing enzymes, mainly proteases, lipases, cutinases, and esterases, by various microorganisms. This review focuses on the enzymatic degradation of PLA and presents different enzymes that were isolated and purified from natural PLA-degrading microorganisms, or recombinantly expressed. The review depicts the main characteristics of the enzymes, including recent advances and analytical methods used to evaluate enantiopurity and depolymerizing activity. While complete degradation of solid PLA particles is still difficult to achieve, future research and improvement of enzyme properties may provide an avenue for the development of advanced procedures for PLA degradation and upcycling, utilizing its building blocks for further applications as envisaged by circular economy principles. KEY POINTS: ⢠Enzymes can be promisingly utilized for PLA upcycling. ⢠Natural and recombinant PLA depolymerases and methods for activity evaluation are summarized. ⢠Approaches to improve enzymatic degradation of PLA are discussed.
Asunto(s)
Biodegradación Ambiental , Poliésteres , Poliésteres/metabolismo , Hidrolasas de Éster Carboxílico/metabolismo , Hidrolasas de Éster Carboxílico/genética , Lipasa/metabolismo , Esterasas/metabolismo , Bacterias/enzimología , Bacterias/metabolismo , Péptido Hidrolasas/metabolismoRESUMEN
The transition towards a sustainable model, particularly the circular economy, emphasizes the importance of redefining waste as a valuable resource, paving the way for innovative upcycling strategies. The olive oil industry, with its significant output of agricultural waste, offers a promising avenue for high-value biomass conversion into useful products through microbial processes. This study focuses on exploring new, high-value applications for olive leaves waste, utilizing a biotechnological approach with Lactobacillus casei for the production of second-generation lactic acid. Contrary to initial expectations, the inherent high polyphenol content and low fermentable glucose levels in olive leaves posed challenges for fermentation. Addressing this, an enzymatic hydrolysis step, following a preliminary extraction process, was implemented to increase glucose availability. Subsequent small-scale fermentation tests were conducted with and without nutrient supplements, identifying the medium that yielded the highest lactic acid production for scale-up. The scaled-up batch fermentation process achieved an enhanced conversion rate (83.58%) and specific productivity (0.26 g/L·h). This research confirms the feasibility of repurposing olive waste leaves for the production of lactic acid, contributing to the advancement of a greener economy through the valorization of agricultural waste. KEY POINTS: ⢠Olive leaves slurry as it did not allow L. casei to ferment. ⢠High concentrations of polyphenols inhibit fermentation of L. casei. ⢠Enzymatic hydrolysis combined to organosolv extraction is the best pretreatment for lactic acid production starting from leaves and olive pruning waste.