Improving heart rate monitoring in the obese with time-of-flight photoplethysmography (TOF-PPG): a quantitative analysis of source-detector-distance effect.

Commercial photoplethysmography (PPG) sensors rely on the measurement of continuous-wave diffuse reflection signals (CW-DRS) to monitor heart rate. Using Monte Carlo modeling of light propagation in skin, we quantitatively evaluate the dependence of continuous-wave photoplethysmography (CW-PPG) in commercial wearables on source-detector distance (SDD). Specifically, when SDD increases from 0.5 mm to 3.3 mm, CW-PPG signal increases by roughly 846% for non-obese (NOB) skin and roughly 683% for morbidly obese (MOB) skin. Ultimately, we introduce the concept of time-of-flight PPG (TOF-PPG) which can significantly improve heart rate signals. Our model shows that the optimized TOF-PPG improves heart rate monitoring experiences by roughly 47.9% in NOB and 93.2% in MOB when SDD = 3.3 mm is at green light. Moving forward, these results will provide a valuable source for hypothesis generation in the scientific community to improve heart rate monitoring.

Determinants of vascular impairment in type 1 diabetes-impact of sex and connexin 37 gene polymorphism: A cross-sectional study.

BACKGROUND: The associations of risk factors with vascular impairment in type 1 diabetes patients seem more complex than that in type 2 diabetes patients. Therefore, we analyzed the associations between traditional and novel cardiovascular risk factors and vascular parameters in individuals with T1D and modifications of these associations according to sex and genetic factors. METHODS: In a cross-sectional study, we analyzed the association of risk factors in T1D individuals younger than 65 years using vascular parameters, such as ankle brachial index (ABI) and toe brachial index (TBI), duplex ultrasound, measuring the presence of plaques in carotid and femoral arteries (Belcaro score) and intima media thickness of carotid arteries (CIMT). We also used photoplethysmography, which measured the interbranch index expressed as the Oliva-Roztocil index (ORI), and analyzed renal parameters, such as urine albumin/creatinine ratio (uACR) and glomerular filtration rate (GFR). We evaluated these associations using multivariate regression analysis, including interactions with sex and the gene for connexin 37 (Cx37) polymorphism (rs1764391). RESULTS: In 235 men and 227 women (mean age 43.6 ± 13.6 years; mean duration of diabetes 22.1 ± 11.3 years), pulse pressure was strongly associated with unfavorable values of most of the vascular parameters under study (ABI, TBI, Belcaro scores, uACR and ORI), whereas plasma lipids, represented by remnant cholesterol (cholesterol - LDL-HDL cholesterol), the atherogenic index of plasma (log (triglycerides/HDL cholesterol) and Lp(a), were associated primarily with renal impairment (uACR, GFR and lipoprotein (a)). Plasma non-HDL cholesterol was not associated with any vascular parameter under study. In contrast to pulse pressure, the associations of lipid factors with kidney and vascular parameters were modified by sex and the Cx37 gene. CONCLUSION: In addition to known information, easily obtainable risk factor, such as pulse pressure, should be considered in individuals with T1D irrespective of sex and genetic background. The associations of plasma lipids with kidney function are complex and associated with sex and genetic factors. The decision of whether pulse pressure, remnant lipoproteins, Lp(a) and other determinants of vascular damage should become treatment targets in T1D should be based on the results of future clinical trials.

Vascular targeted optical theranostics: enhanced photoplethysmography imaging of laser-induced singlet oxygen effects.

The work considers a theranostic system that implements a multimodal approach allowing the simultaneous generation of singlet oxygen and visualization of the various parameters of the vascular bed. The system, together with the developed data processing algorithm, has the ability to assess architectural changes in the vascular network and its blood supply, as well as to identify periodic signal changes associated with mechanisms of blood flow oscillation of various natures. The use of this system seems promising in studying the effect of laser-induced singlet oxygen on the state of the vascular bed, as well as within the framework of the theranostic concept of treatment and diagnosis of oncological diseases and non-oncological vascular anomalies.

Reliable detection of generalized convulsive seizures using an off-the-shelf digital watch: A multisite phase 2 study.

OBJECTIVE: The aim of this study was to develop a machine learning algorithm using an off-the-shelf digital watch, the Samsung watch (SM-R800), and evaluate its effectiveness for the detection of generalized convulsive seizures (GCS) in persons with epilepsy. METHODS: This multisite epilepsy monitoring unit (EMU) phase 2 study included 36 adult patients. Each patient wore a Samsung watch that contained accelerometer, gyroscope, and photoplethysmographic sensors. Sixty-eight time and frequency domain features were extracted from the sensor data and were used to train a random forest algorithm. A testing framework was developed that would better reflect the EMU setting, consisting of (1) leave-one-patient-out cross-validation (LOPO CV) on GCS patients, (2) false alarm rate (FAR) testing on nonseizure patients, and (3) "fixed-and-frozen" prospective testing on a prospective patient cohort. Balanced accuracy, precision, sensitivity, and FAR were used to quantify the performance of the algorithm. Seizure onsets and offsets were determined by using video-electroencephalographic (EEG) monitoring. Feature importance was calculated as the mean decrease in Gini impurity during the LOPO CV testing. RESULTS: LOPO CV results showed balanced accuracy of .93 (95% confidence interval [CI] = .8-.98), precision of .68 (95% CI = .46-.85), sensitivity of .87 (95% CI = .62-.96), and FAR of .21/24 h (interquartile range [IQR] = 0-.90). Testing the algorithm on patients without seizure resulted in an FAR of .28/24 h (IQR = 0-.61). During the "fixed-and-frozen" prospective testing, two patients had three GCS, which were detected by the algorithm, while generating an FAR of .25/24 h (IQR = 0-.89). Feature importance showed that heart rate-based features outperformed accelerometer/gyroscope-based features. SIGNIFICANCE: Commercially available wearable digital watches that reliably detect GCS, with minimum false alarm rates, may overcome usage adoption and other limitations of custom-built devices. Contingent on the outcomes of a prospective phase 3 study, such devices have the potential to provide non-EEG-based seizure surveillance and forecasting in the clinical setting.

Non-invasive methods for heart rate measurement in fish based on photoplethysmography.

Heart rate is a crucial physiological indicator for fish, but current measurement methods are often invasive or require delicate manipulation. In this study, we introduced two non-invasive and easy-to-operate methods based on photoplethysmography, namely reflectance-type photoplethysmography (PPG) and remote photoplethysmography (rPPG), which we applied to the large yellow croaker (Larimichthys crocea). PPG showed perfect synchronization with electrocardiogram (ECG), with a Pearson's correlation coefficient of 0.99999. For rPPG, the results showed good agreement with ECG. Under active provision of green light, the Pearson's correlation coefficient was 0.966, surpassing the value of 0.947 under natural light. Additionally, the root mean square error was 0.810, which was lower than the value of 1.30 under natural light, indicating not only that the rPPG method had relatively high accuracy but also that green light may have the potential to further improve its accuracy.

Genital arousal and responsive desire among women with and without sexual interest/arousal disorder symptoms.

BACKGROUND: Models depicting sexual desire as responsive to sexual arousal may be particularly apt for women experiencing arousal or desire difficulties, and the degree to which arousal triggers desire may depend on the relationship context and desire target and timing-yet, these associations have not been directly tested among women with and without sexual interest/arousal disorder (SIAD). AIM: To assess the role of SIAD status and relationship satisfaction in the associations between genital arousal and 4 types of responsive desire. METHODS: One hundred women (n = 27 meeting diagnostic criteria for SIAD) in romantic relationships with men viewed a sexual film (pleasurable intimate depiction of oral sex and penile-vaginal intercourse) while their genital arousal was recorded via vaginal photoplethysmography (n = 63) or thermal imaging of the labia (n = 37). Partner and solitary desire was assessed immediately before and after the film (immediate desire) and 3 days later (delayed desire). OUTCOMES: Outcomes consisted of genital response (z scored by method) and associations between genital response and responsive sexual desire. RESULTS: The key difference between women with and without SIAD was not in their ability to experience genital arousal but in how their genital responses translated to responsive sexual desire. Women with SIAD actually exhibited greater genital arousal than unaffected women. Associations between genital arousal and desire were significant only for women with SIAD and depended on relationship satisfaction and desire type. For women with SIAD with low relationship satisfaction, higher arousal predicted lower immediate desire for a partner; for those with high relationship satisfaction, arousal was either positively related (vaginal photoplethysmography) or unrelated (thermal imaging of the labia) to immediate desire for a partner. Associations with other desire types were not significant. CLINICAL IMPLICATIONS: Patterns of genital arousal and partner-specific responsive desire among women affected with SIAD were indicative of an avoidance model in response to heightened genital arousal, unless relationship satisfaction was high; attending to genital arousal sensations could be a means of triggering sexual desire for women with SIAD who are satisfied in their relationships. STRENGTHS AND LIMITATIONS: This is one of the first sexual psychophysiologic studies to connect relationship factors to patterns of sexual response. The differing arousal assessment procedures and lack of official diagnosis may have attenuated results. The homogeneous sample and in-person session requirement limit generalizability. CONCLUSION: When compared with unaffected women, women affected by SIAD may exhibit stronger arousal responses with sufficiently incentivized sexual stimuli, and the connection between their genital arousal and responsive desire for their partners may be stronger and more dependent on relationship context.

The utility of wearable headband electroencephalography and pulse photoplethysmography to assess cortical and physiological arousal in individuals with stress-related mental disorders.

Several stress-related mental disorders are characterised by disturbed sleep, but objective sleep biomarkers are not routinely examined in psychiatric patients. We examined the use of wearable-based sleep biomarkers in a psychiatric sample with headband electroencephalography (EEG) including pulse photoplethysmography (PPG), with an additional focus on microstructural elements as especially the shift from low to high frequencies appears relevant for several stress-related mental disorders. We analysed 371 nights of sufficient quality from 83 healthy participants and those with a confirmed stress-related mental disorder (anxiety-affective spectrum). The median value of macrostructural, microstructural (spectral slope fitting), and heart rate variables was calculated across nights and analysed at the individual level (N = 83). The headbands were accepted well by patients and the data quality was sufficient for most nights. The macrostructural analyses revealed trends for significance regarding sleep continuity but not sleep depth variables. The spectral analyses yielded no between-group differences except for a group × age interaction, with the normal age-related decline in the low versus high frequency power ratio flattening in the patient group. The PPG analyses showed that the mean heart rate was higher in the patient group in pre-sleep epochs, a difference that reduced during sleep and dissipated at wakefulness. Wearable devices that record EEG and/or PPG could be used over multiple nights to assess sleep fragmentation, spectral balance, and sympathetic drive throughout the sleep-wake cycle in patients with stress-related mental disorders and healthy controls, although macrostructural and spectral markers did not differ between the two groups.

Calibration-free blood pressure estimation based on a convolutional neural network.

In this study, we conducted research on a deep learning-based blood pressure (BP) estimation model suitable for wearable environments. To measure BP while wearing a wearable watch, it needs to be considered that computing power for signal processing is limited and the input signals are subject to noise interference. Therefore, we employed a convolutional neural network (CNN) as the BP estimation model and utilized time-series electrocardiogram (ECG) and photoplethysmogram (PPG) signals, which are quantifiable in a wearable context. We generated periodic input signals and used differential and thresholding methods to decrease noise in the preprocessing step. We then applied a max-pooling technique with filter sizes of 2 × 1 and 5 × 1 within a 3-layer convolutional neural network to estimate BP. Our method was trained, validated, and tested using 2.4 million data samples from 49 patients in the intensive care unit. These samples, totaling 3.1 GB were obtained from the publicly accessible MIMIC database. As a result of a test with 480,000 data samples, the average root mean square error in BP estimation was 3.41, 5.80, and 2.78 mm Hg in the prediction of pulse pressure, systolic BP (SBP), and diastolic BP (DBP), respectively. The cumulative error percentage less than 5 mm Hg was 68% and 93% for SBP and DBP, respectively. In addition, the cumulative error percentage less than 15 mm Hg was 98% and 99% for SBP and DBP. Subsequently, we evaluated the impact of changes in input signal length (1 cycle vs. 30 s) and the introduction of noise on BP estimation results. The experimental results revealed that the length of the input signal did not significantly affect the performance of CNN-based analysis. When estimating BP using noise-added ECG signals, the mean absolute error (MAE) for SBP and DBP was 9.72 and 6.67 mm Hg, respectively. Meanwhile, when using noise-added PPG signals, the MAE for SBP and DBP was 26.85 and 14.00 mm Hg, respectively. Therefore, this study confirmed that using ECG signals rather than PPG signals is advantageous for noise reduction in a wearable environment. Besides, short sampling frames without calibration can be effective as input signals. Furthermore, it demonstrated that using a model suitable for information extraction rather than a specialized deep learning model for sequential data can yield satisfactory results in BP estimation.

Publication guidelines for human heart rate and heart rate variability studies in psychophysiology-Part 1: Physiological underpinnings and foundations of measurement.

This Committee Report provides methodological, interpretive, and reporting guidance for researchers who use measures of heart rate (HR) and heart rate variability (HRV) in psychophysiological research. We provide brief summaries of best practices in measuring HR and HRV via electrocardiographic and photoplethysmographic signals in laboratory, field (ambulatory), and brain-imaging contexts to address research questions incorporating measures of HR and HRV. The Report emphasizes evidence for the strengths and weaknesses of different recording and derivation methods for measures of HR and HRV. Along with this guidance, the Report reviews what is known about the origin of the heartbeat and its neural control, including factors that produce and influence HRV metrics. The Report concludes with checklists to guide authors in study design and analysis considerations, as well as guidance on the reporting of key methodological details and characteristics of the samples under study. It is expected that rigorous and transparent recording and reporting of HR and HRV measures will strengthen inferences across the many applications of these metrics in psychophysiology. The prior Committee Reports on HR and HRV are several decades old. Since their appearance, technologies for human cardiac and vascular monitoring in laboratory and daily life (i.e., ambulatory) contexts have greatly expanded. This Committee Report was prepared for the Society for Psychophysiological Research to provide updated methodological and interpretive guidance, as well as to summarize best practices for reporting HR and HRV studies in humans.

Real-world validation of smartphone-based photoplethysmography for rate and rhythm monitoring in atrial fibrillation.

AIMS: Photoplethysmography- (PPG) based smartphone applications facilitate heart rate and rhythm monitoring in patients with paroxysmal and persistent atrial fibrillation (AF). Despite an endorsement from the European Heart Rhythm Association, validation studies in this setting are lacking. Therefore, we evaluated the accuracy of PPG-derived heart rate and rhythm classification in subjects with an established diagnosis of AF in unsupervised real-world conditions. METHODS AND RESULTS: Fifty consecutive patients were enrolled, 4 weeks before undergoing AF ablation. Patients used a handheld single-lead electrocardiography (ECG) device and a fingertip PPG smartphone application to record 3907 heart rhythm measurements twice daily during 8 weeks. The ECG was performed immediately before and after each PPG recording and was given a diagnosis by the majority of three blinded cardiologists. A consistent ECG diagnosis was exhibited along with PPG data of sufficient quality in 3407 measurements. A single measurement exhibited good quality more often with ECG (93.2%) compared to PPG (89.5%; P < 0.001). However, PPG signal quality improved to 96.6% with repeated measurements. Photoplethysmography-based detection of AF demonstrated excellent sensitivity [98.3%; confidence interval (CI): 96.7-99.9%], specificity (99.9%; CI: 99.8-100.0%), positive predictive value (99.6%; CI: 99.1-100.0%), and negative predictive value (99.6%; CI: 99.0-100.0%). Photoplethysmography underestimated the heart rate in AF with 6.6 b.p.m. (95% CI: 5.8 b.p.m. to 7.4 b.p.m.). Bland-Altman analysis revealed increased underestimation in high heart rates. The root mean square error was 11.8 b.p.m. CONCLUSION: Smartphone applications using PPG can be used to monitor patients with AF in unsupervised real-world conditions. The accuracy of AF detection algorithms in this setting is excellent, but PPG-derived heart rate may tend to underestimate higher heart rates.

Validation of a novel smartphone-based photoplethysmographic method for ambulatory heart rhythm diagnostics: the SMARTBEATS study.

AIMS: In the current guidelines, smartphone photoplethysmography (PPG) is not recommended for diagnosis of atrial fibrillation (AF), without a confirmatory electrocardiogram (ECG) recording. Previous validation studies have been performed under supervision in healthcare settings, with limited generalizability of the results. We aim to investigate the diagnostic performance of a smartphone-PPG method in a real-world setting, with ambulatory unsupervised smartphone-PPG recordings, compared with simultaneous ECG recordings and including patients with atrial flutter (AFL). METHODS AND RESULTS: Unselected patients undergoing direct current cardioversion for treatment of AF or AFL were asked to perform 1-min heart rhythm recordings post-treatment, at least twice daily for 30 days at home, using an iPhone 7 smartphone running the CORAI Heart Monitor PPG application simultaneously with a single-lead ECG recording (KardiaMobile). Photoplethysmography and ECG recordings were read independently by two experienced readers. In total, 280 patients recorded 18 005 simultaneous PPG and ECG recordings. Sufficient quality for diagnosis was seen in 96.9% (PPG) vs. 95.1% (ECG) of the recordings (P < 0.001). Manual reading of the PPG recordings, compared with manually interpreted ECG recordings, had a sensitivity, specificity, and overall accuracy of 97.7%, 99.4%, and 98.9% with AFL recordings included and 99.0%, 99.7%, and 99.5%, respectively, with AFL recordings excluded. CONCLUSION: A novel smartphone-PPG method can be used by patients unsupervised at home to achieve accurate heart rhythm diagnostics of AF and AFL with very high sensitivity and specificity. This smartphone-PPG device can be used as an independent heart rhythm diagnostic device following cardioversion, without the requirement of confirmation with ECG.

Prospective multicenter study of continuous tonic-clonic seizure monitoring on Apple Watch in epilepsy monitoring units and ambulatory environments.

OBJECTIVE: Evaluate the performance of a custom application developed for tonic-clonic seizure (TCS) monitoring on a consumer-wearable (Apple Watch) device. METHODS: Participants with a history of convulsive epileptic seizures were recruited for either Epilepsy Monitoring Unit (EMU) or ambulatory (AMB) monitoring; participants without epilepsy (normal controls [NC]) were also enrolled in the AMB group. Both EMU and AMB participants wore an Apple Watch with a research app that continuously recorded accelerometer and photoplethysmography (PPG) signals, and ran a fixed-and-frozen tonic-clonic seizure detection algorithm during the testing period. This algorithm had been previously developed and validated using a separate training dataset. All EMU convulsive events were validated by video-electroencephalography (video-EEG); AMB events were validated by caregiver reporting and follow-ups. Device performance was characterized and compared to prior monitoring devices through sensitivity, false alarm rate (FAR; false-alarms per 24 h), precision, and detection delay (latency). RESULTS: The EMU group had 85 participants (4,279 h, 19 TCS from 15 participants) enrolled across four EMUs; the AMB group had 21 participants (13 outpatient, 8 NC, 6,735 h, 10 TCS from 3 participants). All but one AMB participant completed the study. Device performance in the EMU group included a sensitivity of 100 % [95 % confidence interval (CI) 79-100 %]; an FAR of 0.05 [0.02, 0.08] per 24 h; a precision of 68 % [48 %, 83 %]; and a latency of 32.07 s [standard deviation (std) 10.22 s]. The AMB group had a sensitivity of 100 % [66-100 %]; an FAR of 0.13 [0.08, 0.24] per 24 h; a precision of 22 % [11 %, 37 %]; and a latency of 37.38 s [13.24 s]. Notably, a single AMB participant was responsible for 8 of 31 false alarms. The AMB FAR excluding this participant was 0.10 [0.07, 0.14] per 24 h. DISCUSSION: This study demonstrates the practicability of TCS monitoring on a popular consumer wearable (Apple Watch) in daily use for people with epilepsy. The monitoring app had a high sensitivity and a substantially lower FAR than previously reported in both EMU and AMB environments.

Evaluation of an algorithm-guided photoplethysmography for atrial fibrillation burden using a smartwatch.

BACKGROUND: Wearable devices based on the PPG algorithm can detect atrial fibrillation (AF) effectively. However, further investigation of its application on long-term, continuous monitoring of AF burden is warranted. METHOD: The performance of a smartwatch with continuous photoplethysmography (PPG) and PPG-based algorithms for AF burden estimation was evaluated in a prospective study enrolling AF patients admitted to Beijing Anzhen Hospital for catheter ablation from September to November 2022. A continuous Electrocardiograph patch (ECG) was used as the reference device to validate algorithm performance for AF detection in 30-s intervals. RESULTS: A total of 578669 non-overlapping 30-s intervals for PPG and ECG each from 245 eligible patients were generated. An interval-level sensitivity of PPG was 96.3% (95% CI 96.2%-96.4%), and specificity was 99.5% (95% CI 99.5%-99.6%) for the estimation of AF burden. AF burden estimation by PPG was highly correlated with AF burden calculated by ECG via Pearson correlation coefficient (R2 = 0.996) with a mean difference of -0.59 (95% limits of agreement, -7.9% to 6.7%). The subgroup study showed the robust performance of the algorithm in different subgroups, including heart rate and different hours of the day. CONCLUSION: Our results showed the smartwatch with an algorithm-based PPG monitor has good accuracy and stability in continuously monitoring AF burden compared with ECG patch monitors, indicating its potential for diagnosing and managing AF.

High-precision spectra captured by a spectral camera and suppression of their nonlinearity.

The high sensitivity of photoplethysmography (PPG) spectral signals provides conditions for extracting dynamic spectra carrying nonlinear information. By the idea of spatial conversion precision, this paper uses a spectral camera to collect highly sensitive spectral data of 24 wavelengths and proposes a method for extracting dynamic spectra of three different optical path lengths and their joint modeling. In the experiment, the models of the red blood cells and white blood cells established by the joint spectra achieved good results, with the correlation coefficients above 0.77. This study has great significance for achieving high-precision noninvasive quantitative analysis of human blood components.

Feasibility and accuracy of noninvasive continuous hemoglobin monitoring using transesophageal photoplethysmography in porcine model.

BACKGROUND: Continuous and noninvasive hemoglobin (Hb) monitoring during surgery is essential for anesthesiologists to make transfusions decisions. The aim of this study was to investigate the feasibility and accuracy of noninvasive and continuous Hb monitoring using transesophageal descending aortic photoplethysmography (dPPG) in porcine model. METHODS: Nineteen landrace pigs, aged 3 to 5 months and weighing 30 to 50 kg, were enrolled in this study. A homemade oximetry sensor, including red (660 nm) and infrared (940 nm) lights, was placed in the esophagus for dPPG signal detection to pair with the corresponding reference Hb values (Hbi-STAT) measured by blood gas analysis. The decrease and increase changes in Hb concentration were achieved by hemodilution and transfusion. Metrics, including alternating current (AC), direct current (DC), and AC/DC for both red and infrared light were extracted from the dPPG signal. A receiver operating characteristic (ROC) curve was built to evaluate the performance of dPPG metrics in predicting the Hb "trigger threshold" of transfusion (Hb < 60 g/L and Hb > 100 g/L). Agreement and trending ability between Hb measured by dPPG (HbdPPG) and by blood gas analysis were analyzed by Bland-Altman method and polar plot graph. Error grid analysis was also performed to evaluate clinical significance of HbdPPG measurement. RESULTS: The dPPG signal was successfully detected in all of the enrolled experimental pigs, without the occurrence of a continuous loss of dPPG signal for 2 min during the entire measurement. A total of 376 pairs of dPPG signal and Hbi-STAT were acquired. ACred/DCred and ACinf/DCinf had moderate correlations with Hbi-STAT, and the correlation coefficients were 0.790 and 0.782, respectively. The areas under the ROC curve for ACred/DCred and ACinf/DCinf in predicting Hbi-STAT < 60 g/L were 0.85 and 0.75, in predicting Hbi-STAT > 100 g/L were 0.90 and 0.83, respectively. Bland-Altman analysis and polar plot showed a small bias (1.69 g/L) but a wide limit of agreement (-26.02-29.40 g/L) and a poor trend ability between HbdPPG and Hbi-STAT. Clinical significance analysis showed that 82% of the data lay within the Zone A, 18% within the Zone B, and 0% within the Zone C. CONCLUSION: It is feasible to establish a noninvasive and continuous Hb monitoring by transesophageal dPPG signal. The ACred/DCred extracted from the dPPG signal could provide a sensitive prediction of the Hb threshold for transfusion. The Hb concentration measured by dPPG signal has a moderate correlation with that measured by blood gas analysis. This animal study may provide an experimental basis for the development of bedside HbdPPG monitoring in the future.

Cuffless Blood Pressure in clinical practice: challenges, opportunities and current limits.

Background: Cuffless blood pressure measurement technologies have attracted significant attention for their potential to transform cardiovascular monitoring.Methods: This updated narrative review thoroughly examines the challenges, opportunities, and limitations associated with the implementation of cuffless blood pressure monitoring systems.Results: Diverse technologies, including photoplethysmography, tonometry, and ECG analysis, enable cuffless blood pressure measurement and are integrated into devices like smartphones and smartwatches. Signal processing emerges as a critical aspect, dictating the accuracy and reliability of readings. Despite its potential, the integration of cuffless technologies into clinical practice faces obstacles, including the need to address concerns related to accuracy, calibration, and standardization across diverse devices and patient populations. The development of robust algorithms to mitigate artifacts and environmental disturbances is essential for extracting clear physiological signals. Based on extensive research, this review emphasizes the necessity for standardized protocols, validation studies, and regulatory frameworks to ensure the reliability and safety of cuffless blood pressure monitoring devices and their implementation in mainstream medical practice. Interdisciplinary collaborations between engineers, clinicians, and regulatory bodies are crucial to address technical, clinical, and regulatory complexities during implementation. In conclusion, while cuffless blood pressure monitoring holds immense potential to transform cardiovascular care. The resolution of existing challenges and the establishment of rigorous standards are imperative for its seamless incorporation into routine clinical practice.Conclusion: The emergence of these new technologies shifts the paradigm of cardiovascular health management, presenting a new possibility for non-invasive continuous and dynamic monitoring. The concept of cuffless blood pressure measurement is viable and more finely tuned devices are expected to enter the market, which could redefine our understanding of blood pressure and hypertension.

This review explores cuffless blood pressure technologies and their impact on clinical practice, highlighting innovative devices that offer non-invasive, continuous and non-continuous monitoring without a cuff. Signal processing is essential for ensuring accurate readings, as it filters out unwanted artifacts and environmental disturbances which could make the reading inaccurate. While these advancements show great potential for transforming cardiovascular care, there are still several challenges to overcome, including the need for standardized protocols and validation studies to ensure their reliability and safety in clinical settings. Collaborative efforts between engineers, clinicians, and regulatory bodies are needed to address the technical and regulatory complexities surrounding the implementation of these technologies. These cuffless blood pressure measurement devices have the potential to reshape how we understand and manage blood pressure and hypertension.

A pilot clinical study to estimate intracranial pressure utilising cerebral photoplethysmograms in traumatic brain injury patients.

PURPOSE: In this research, a non-invasive intracranial pressure (nICP) optical sensor was developed and evaluated in a clinical pilot study. The technology relied on infrared light to probe brain tissue, using photodetectors to capture backscattered light modulated by vascular pulsations within the brain's vascular tissue. The underlying hypothesis was that changes in extramural arterial pressure could affect the morphology of recorded optical signals (photoplethysmograms, or PPGs), and analysing these signals with a custom algorithm could enable the non-invasive calculation of intracranial pressure (nICP). METHODS: This pilot study was the first to evaluate the nICP probe alongside invasive ICP monitoring as a gold standard. nICP monitoring occurred in 40 patients undergoing invasive ICP monitoring, with data randomly split for machine learning. Quality PPG signals were extracted and analysed for time-based features. The study employed Bland-Altman analysis and ROC curve calculations to assess nICP accuracy compared to invasive ICP data. RESULTS: Successful acquisition of cerebral PPG signals from traumatic brain injury (TBI) patients allowed for the development of a bagging tree model to estimate nICP non-invasively. The nICP estimation exhibited 95% limits of agreement of 3.8 mmHg with minimal bias and a correlation of 0.8254 with invasive ICP monitoring. ROC curve analysis showed strong diagnostic capability with 80% sensitivity and 89% specificity. CONCLUSION: The clinical evaluation of this innovative optical nICP sensor revealed its ability to estimate ICP non-invasively with acceptable and clinically useful accuracy. This breakthrough opens the door to further technological refinement and larger-scale clinical studies in the future. TRIAL REGISTRATION: NCT05632302, 11th November 2022, retrospectively registered.

InsightSleepNet: the interpretable and uncertainty-aware deep learning network for sleep staging using continuous Photoplethysmography.

BACKGROUND: This study was conducted to address the existing drawbacks of inconvenience and high costs associated with sleep monitoring. In this research, we performed sleep staging using continuous photoplethysmography (PPG) signals for sleep monitoring with wearable devices. Furthermore, our aim was to develop a more efficient sleep monitoring method by considering both the interpretability and uncertainty of the model's prediction results, with the goal of providing support to medical professionals in their decision-making process. METHOD: The developed 4-class sleep staging model based on continuous PPG data incorporates several key components: a local attention module, an InceptionTime module, a time-distributed dense layer, a temporal convolutional network (TCN), and a 1D convolutional network (CNN). This model prioritizes both interpretability and uncertainty estimation in its prediction results. The local attention module is introduced to provide insights into the impact of each epoch within the continuous PPG data. It achieves this by leveraging the TCN structure. To quantify the uncertainty of prediction results and facilitate selective predictions, an energy score estimation is employed. By enhancing both the performance and interpretability of the model and taking into consideration the reliability of its predictions, we developed the InsightSleepNet for accurate sleep staging. RESULT: InsightSleepNet was evaluated using three distinct datasets: MESA, CFS, and CAP. Initially, we assessed the model's classification performance both before and after applying an energy score threshold. We observed a significant improvement in the model's performance with the implementation of the energy score threshold. On the MESA dataset, prior to applying the energy score threshold, the accuracy was 84.2% with a Cohen's kappa of 0.742 and weighted F1 score of 0.842. After implementing the energy score threshold, the accuracy increased to a range of 84.8-86.1%, Cohen's kappa values ranged from 0.75 to 0.78 and weighted F1 scores ranged from 0.848 to 0.861. In the case of the CFS dataset, we also noted enhanced performance. Before the application of the energy score threshold, the accuracy stood at 80.6% with a Cohen's kappa of 0.72 and weighted F1 score of 0.808. After thresholding, the accuracy improved to a range of 81.9-85.6%, Cohen's kappa values ranged from 0.74 to 0.79 and weighted F1 scores ranged from 0.821 to 0.857. Similarly, on the CAP dataset, the initial accuracy was 80.6%, accompanied by a Cohen's kappa of 0.73 and weighted F1 score was 0.805. Following the application of the threshold, the accuracy increased to a range of 81.4-84.3%, Cohen's kappa values ranged from 0.74 to 0.79 and weighted F1 scores ranged from 0.813 to 0.842. Additionally, by interpreting the model's predictions, we obtained results indicating a correlation between the peak of the PPG signal and sleep stage classification. CONCLUSION: InsightSleepNet is a 4-class sleep staging model that utilizes continuous PPG data, serves the purpose of continuous sleep monitoring with wearable devices. Beyond its primary function, it might facilitate in-depth sleep analysis by medical professionals and empower them with interpretability for intervention-based predictions. This capability can also support well-informed clinical decision-making, providing valuable insights and serving as a reliable second opinion in medical settings.

Introducing the Pi-CON Methodology to Overcome Usability Deficits during Remote Patient Monitoring.

The adoption of telehealth has soared, and with that the acceptance of Remote Patient Monitoring (RPM) and virtual care. A review of the literature illustrates, however, that poor device usability can impact the generated data when using Patient-Generated Health Data (PGHD) devices, such as wearables or home use medical devices, when used outside a health facility. The Pi-CON methodology is introduced to overcome these challenges and guide the definition of user-friendly and intuitive devices in the future. Pi-CON stands for passive, continuous, and non-contact, and describes the ability to acquire health data, such as vital signs, continuously and passively with limited user interaction and without attaching any sensors to the patient. The paper highlights the advantages of Pi-CON by leveraging various sensors and techniques, such as radar, remote photoplethysmography, and infrared. It illustrates potential concerns and discusses future applications Pi-CON could be used for, including gait and fall monitoring by installing an omnipresent sensor based on the Pi-CON methodology. This would allow automatic data collection once a person is recognized, and could be extended with an integrated gateway so multiple cameras could be installed to enable data feeds to a cloud-based interface, allowing clinicians and family members to monitor patient health status remotely at any time.

Exploring the Possibility of Photoplethysmography-Based Human Activity Recognition Using Convolutional Neural Networks.

Various sensing modalities, including external and internal sensors, have been employed in research on human activity recognition (HAR). Among these, internal sensors, particularly wearable technologies, hold significant promise due to their lightweight nature and simplicity. Recently, HAR techniques leveraging wearable biometric signals, such as electrocardiography (ECG) and photoplethysmography (PPG), have been proposed using publicly available datasets. However, to facilitate broader practical applications, a more extensive analysis based on larger databases with cross-subject validation is required. In pursuit of this objective, we initially gathered PPG signals from 40 participants engaged in five common daily activities. Subsequently, we evaluated the feasibility of classifying these activities using deep learning architecture. The model's performance was assessed in terms of accuracy, precision, recall, and F-1 measure via cross-subject cross-validation (CV). The proposed method successfully distinguished the five activities considered, with an average test accuracy of 95.14%. Furthermore, we recommend an optimal window size based on a comprehensive evaluation of performance relative to the input signal length. These findings confirm the potential for practical HAR applications based on PPG and indicate its prospective extension to various domains, such as healthcare or fitness applications, by concurrently analyzing behavioral and health data through a single biometric signal.