Estimation of sorption-desorption characteristics of biosorbent of Lantana camara leaves for removal of Pb (II) ions from wastewater.

This study points out the method regarding the removal of Pb (II) ions from water by treatment with Lantana camara leaves' biosorbent (LCLB). The sorption process was investigated by varying different parameters pH, contact time, adsorbent dose, initial metal ion concentration, and temperature. For a 5.00 g sorbent dose and a 45 min of the contact period, a Pb (II) ion solution with an initial metal ion concentration of 10 mg/L resulted in 90.7% maximum elimination at an optimum pH 6 and temperature 298 ± 1.5 K with LCLB. The adsorption process was spontaneous and exothermic. The maximum monolayer adsorption was 3.5 mg/g for Pb (II) sorption using LCLB. Adsorption of Pb (II) ions using LCLB (R2 > 0.999) followed the pseudo-second-order kinetics. The spectroscopic characterization was done by fourier transform infrared (FT-IR) analysis, while scanning electron microscope (SEM) images were captured for the morphological characterization. Desorption experiments revealed that hydrochloric acid has a strong potential as an eluent for Pb (II) ion desorption. The findings proposed that LCLB can be used as an effectual and cost-effective biosorbent for the expulsion of Pb (II) ions.

Self-standing, conducting and capacitive biomimetic hybrid nanomembranes for selective molecular ion separation.

Hybrid free-standing biomimetic materials are developed by integrating the VDAC36 ß-barrel protein into robust and flexible three-layered polymer nanomembranes. The first and third layers are prepared by spin-coating a mixture of poly(lactic acid) (PLA) and poly(vinyl alcohol) (PVA). PVA nanofeatures are transformed into controlled nanoperforations by solvent-etching. The two nanoperforated PLA layers are separated by an electroactive layer, which is successfully electropolymerized by introducing a conducting sacrificial substrate under the first PLA nanosheet. Finally, the nanomaterial is consolidated by immobilizing the VDAC36 protein, active as an ion channel, into the nanoperforations of the upper layer. The integration of the protein causes a significant reduction of the material resistance, which decreases from 21.9 to 3.9 kΩ cm2. Electrochemical impedance spectroscopy studies using inorganic ions and molecular metabolites (i.e.l-lysine and ATP) not only reveal that the hybrid films behave as electrochemical supercapacitors but also indicate the most appropriate conditions to obtain selective responses against molecular ions as a function of their charge. The combination of polymers and proteins is promising for the development of new devices for engineering, biotechnological and biomedical applications.

Advances in aptamer screening and aptasensors' detection of heavy metal ions.

Heavy metal pollution has become more and more serious with industrial development and resource exploitation. Because heavy metal ions are difficult to be biodegraded, they accumulate in the human body and cause serious threat to human health. However, the conventional methods to detect heavy metal ions are more strictly to the requirements by detection equipment, sample pretreatment, experimental environment, etc. Aptasensor has the advantages of strong specificity, high sensitivity and simple preparation to detect small molecules, which provides a new direction platform in the detection of heavy metal ions. This paper reviews the selection of aptamers as target for heavy metal ions since the 21th century and aptasensors application for detection of heavy metal ions that were reported in the past five years. Firstly, the selection methods for aptamers with high specificity and high affinity are introduced. Construction methods and research progress on sensor based aptamers as recognition element are also introduced systematically. Finally, the challenges and future opportunities of aptasensors in detecting heavy metal ions are discussed.

Elemental Characterization of Ciders and Other Low-Percentage Alcoholic Beverages Available on the Polish Market.

Seventy-three samples of alcoholic beverages and juices that were purchased on the Polish market and home-made were analyzed for their elemental profiles. The levels of 23 metals were determined by ICP-MS (Ag, Ba, Bi, Cd, Co, Cr, Li, Mn, Ni, Pb, Sr and Tl), ICP-OES (Al, B, Ca, Cu, Fe, K, Mg, Na, Ti and Zn) and CVAAS (Hg) techniques in twenty-five samples of ciders widely available on the Polish market; six samples of home-made ciders; two samples of juices used in the production of these ciders; and forty samples of low-percentage, flavored alcoholic beverages based on beer. The gathered analytical data confirmed that the final elemental fingerprint of a product is affected by the elemental fingerprint of the ingredients used (apple variety) as well as the technology and equipment used by the producer, and in the case of commercial ciders, also the impact of type of the packaging used was proven. These factors are specific to each producer and the influence of the mentioned above parameters was revealed as a result of the performed analysis. Additionally, the inclusion of the home-made ciders in the data set helped us to understand the potential origin of some elements, from the raw materials to the final products. The applied statistical tests revealed (Kruskal-Wallis and ANOVA) the existence of statistically significant differences in the concentration of the following metals: Ag, Al, B, Bi, Co, Cr, Cu, Fe, K, Li, Mg, Na, Ni, Ti and Zn in terms of the type of cider origin (commercial and home-made). In turn, for different packaging (can or bottle) within one brand of commercial cider, the existence of statistically significant differences for Cu, Mn and Na was proved. The concentrations of all determined elements in the commercial cider from the Polish market and home-made cider samples can be considered as nontoxic, because the measured levels of elements indicated in the regulations were lower than the allowable limits. Moreover, the obtained results can be treated as preliminary for the potential authentication of products in order to distinguish the home-made (fake) from the authentic products, especially for premium-class alcoholic beverages.

Removal of Mercury Ions from Aqueous Solutions by Crosslinked Chitosan-based Adsorbents: A Mini Review.

Abatement of mercury emissions in air and waters has become a global challenge due to the toxicity of mercury species for life, yet actual remediation techniques are limited. In particular, adsorption of mercury ions onto solids is widely used but most adsorption techniques are not specific, and in turn, removal efficiency is lower. Adsorbents developed so far include activated carbon, clay, bentonite, cellulose and chitosan. Chitosan derivatives have recently attracted research attention for water purification because their molecular frames contain a large amount of -NH2 and -OH groups that can chelate with metal ions specifically. This manuscript reviews recent advances in chitosan-based adsorbents designed to remove mercury ions from wastewater. Focus is placed on their design, synthesis, characterization, adsorption properties, adsorption mechanisms and applications.

Electrochemical Biosensors Based on S-Layer Proteins.

Designing and development of electrochemical biosensors enable molecule sensing and quantification of biochemical compositions with multitudinous benefits such as monitoring, detection, and feedback for medical and biotechnological applications. Integrating bioinspired materials and electrochemical techniques promote specific, rapid, sensitive, and inexpensive biosensing platforms for (e.g., point-of-care testing). The selection of biomaterials to decorate a biosensor surface is a critical issue as it strongly affects selectivity and sensitivity. In this context, smart biomaterials with the intrinsic self-assemble capability like bacterial surface (S-) layer proteins are of paramount importance. Indeed, by forming a crystalline two-dimensional protein lattice on many sensors surfaces and interfaces, the S-layer lattice constitutes an immobilization matrix for small biomolecules and lipid membranes and a patterning structure with unsurpassed spatial distribution for sensing elements and bioreceptors. This review aims to highlight on exploiting S-layer proteins in biosensor technology for various applications ranging from detection of metal ions over small organic compounds to cells. Furthermore, enzymes immobilized on the S-layer proteins allow specific detection of several vital biomolecules. The special features of the S-layer protein lattice as part of the sensor architecture enhances surface functionalization and thus may feature an innovative class of electrochemical biosensors.

High Aspect Ratio Fin-Ion Sensitive Field Effect Transistor: Compromises toward Better Electrochemical Biosensing.

The development of next generation medicines demands more sensitive and reliable label-free sensing able to cope with increasing needs of multiplexing and shorter times to results. Field effect transistor-based biosensors emerge as one of the main possible technologies to cover the existing gap. The general trend for the sensors has been miniaturization with the expectation of improving sensitivity and response time but presenting issues with reproducibility and noise level. Here we propose a Fin-Field Effect Transistor (FinFET) with a high height to width aspect ratio for electrochemical biosensing solving the issue of nanosensors in terms of reproducibility and noise, while keeping the fast response time. We fabricated different devices and characterized their performance with their response to the pH changes that fitted to a Nernst-Poisson model. The experimental data were compared with simulations of devices with different aspect ratio, establishing an advantage in linearity and lower device resistance to provide higher current signals for the FinFETs with higher aspect ratio. In addition, these FinFETs promise the optimization of reliability and efficiency in terms of limits of detection for which the interplay of the size and geometry of the sensor with the diffusion of the analytes plays a pivotal role.

Manganese as a Catalytic Mediator for Photo-oxidation and Breaking the pH Limitation of Nanozymes.

A long-standing challenge in nanozyme catalysis is low activity at physiological pH, especially for oxidase- and peroxidase-mimicking nanozymes. We herein communicate that Mn(II) can promote catalysis at neutral pH for carbon dots (C-dots) as a photo-oxidase nanozyme. The C-dots produce singlet oxygen upon light irradiation to oxidize Mn(II) to Mn(III), which is confirmed by a suite of spectroscopic evidence. The in situ produced Mn(III) acts as a mediator, analogous to mediators in electrochemistry to enhance electron transfer. None of the other divalent metal ions show such an effect, allowing the selective detection of Mn(II) down to 5 nM. EDTA further enhances the activity by stabilizing the highly active Mn(III), producing an intense blue color by oxidizing 3,3',5,5'-tetramethylbenzidine (TMB) in just 10 s. Finally, this reaction was used to evaluate antioxidants. With this method, more analytical and biomedical applications of nanozymes can be exploited at neutral pH, and it may inspire other strategies to overcome the pH limitation in nanozyme catalysis.

Development of an Atmospheric Pressure Chemical Ionization Interface for GC-MS.

A closed atmospheric pressure chemical ionization (APCI) ion source as interface between a gas chromatograph (GC) and a triple quadrupole mass spectrometer (QqQ-MS) was developed. The influence of different ion source conditions, such as humidity, make-up gas flow, and the position of the GC column, were investigated and determined as main factors to increase sensitivity and repeatability of the system. For a performance test under real conditions, the new APCI ion source was used for the determination of plant protection products in commercially available coffee beans from Vietnam. The ionization behavior was investigated and the majority of the analytes were detected as [MH]+, [M]+∙, or as characteristic fragment ions, which have been assigned to ion source fragmentation. The developed GC-MS methods are based on tandem MS (MS/MS) and revealed for the plant protection products limits of detection (LOD) between 1 and 250 pg on column and relative standard derivations for all compounds < 16%. The used ultrasonic solid-liquid extraction yielded recovery rates of approximately 60 to 100%. Residues of herbicide methyl esters, organophosphorus compounds, and organonitrogen compounds have been detected in the analyzed coffee beans.

Rational Design of Polyamine-Based Cryogels for Metal Ion Sorption.

Here we report the method of fabrication of supermacroporous monolith sorbents (cryogels) via covalent cross-linking of polyallylamine (PAA) with diglycidyl ether of 1,4-butandiol. Using comparative analysis of the permeability and sorption performance of the obtained PAA cryogels and earlier developed polyethyleneimine (PEI) cryogels, we have demonstrated the advantages and disadvantages of these polymers as sorbents of heavy metal ions (Cu(II), Zn(II), Cd(II), and Ni(II)) in fixed-bed applications and as supermacroporous matrices for the fabrication of composite cryogels containing copper ferrocyanide (CuFCN) for cesium ion sorption. Applying the rate constant distribution (RCD) model to the kinetic curves of Cu(II) ion sorption on PAA and PEI cryogels, we have elucidated the difference in sorption/desorption rates and affinity constants of these materials and showed that physical sorption contributed to the Cu(II) uptake by PAA, but not to that by PEI cryogels. It was shown that PAA cryogels had significantly higher selectivity for Cu(II) sorption in the presence of Zn(II) and Cd(II) ions in comparison with that of PEI cryogels, while irreversible sorption of Co(II) ions by PEI can be used for the separation of Ni(II) and Co(II) ions. Using IR and Mössbauer spectroscopy, we have demonstrated that strong complexation of Cu(II) ions with PEI significantly affects the in situ formation of Cu(II) ferrocyanide nanosorbents leading to their inefficiency for Cs+ ions selective uptake, whereas PAA cryogel was applicable for the fabrication of efficient monolith composites via the in situ formation of CuFCN or loading of ex situ formed CuFCN colloids.

SLIM Ultrahigh Resolution Ion Mobility Spectrometry Separations of Isotopologues and Isotopomers Reveal Mobility Shifts due to Mass Distribution Changes.

We report on separations of ion isotopologues and isotopomers using ultrahigh-resolution traveling wave-based Structures for Lossless Ion Manipulations with serpentine ultralong path and extended routing ion mobility spectrometry coupled to mass spectrometry (SLIM SUPER IMS-MS). Mobility separations of ions from the naturally occurring ion isotopic envelopes (e.g., [M], [M+1], [M+2], ... ions) showed the first and second isotopic peaks (i.e., [M+1] and [M+2]) for various tetraalkylammonium ions could be resolved from their respective monoisotopic ion peak ([M]) after SLIM SUPER IMS with resolving powers of ∼400-600. Similar separations were obtained for other compounds (e.g., tetrapeptide ions). Greater separation was obtained using argon versus helium drift gas, as expected from the greater reduced mass contribution to ion mobility described by the Mason-Schamp relationship. To more directly explore the role of isotopic substitutions, we studied a mixture of specific isotopically substituted (15N, 13C, and 2H) protonated arginine isotopologues. While the separations in nitrogen were primarily due to their reduced mass differences, similar to the naturally occurring isotopologues, their separations in helium, where higher resolving powers could also be achieved, revealed distinct additional relative mobility shifts. These shifts appeared correlated, after correction for the reduced mass contribution, with changes in the ion center of mass due to the different locations of heavy atom substitutions. The origin of these apparent mass distribution-induced mobility shifts was then further explored using a mixture of Iodoacetyl Tandem Mass Tag (iodoTMT) isotopomers (i.e., each having the same exact mass, but with different isotopic substitution sites). Again, the observed mobility shifts appeared correlated with changes in the ion center of mass leading to multiple monoisotopic mobilities being observed for some isotopomers (up to a ∼0.04% difference in mobility). These mobility shifts thus appear to reflect details of the ion structure, derived from the changes due to ion rotation impacting collision frequency or momentum transfer, and highlight the potential for new approaches for ion structural characterization.

The dynamics of band (peak) shape development in capillary zone electrophoresis in light of the linear theory of electromigration.

The continuity equations that describe the movement of ions in liquid solutions under the influence of an external stationary electric field, as it is utilized in electrophoresis, were introduced a long time ago starting with Kohlrausch in 1897. From that time on, there have been many attempts to solve the equations and to discuss the results. In electrophoresis, special attention has always been devoted to the peak shapes obtained by the detector since the shapes have a tight connection with the phenomena taking place during electromigration and influence the efficiency and selectivity of the separation. Among these phenomena, the most important is electromigration dispersion. In this commented review paper, we compare various models of electromigration, try to find points that connect them, and discuss the range of their validity in light of the linear and nonlinear theory of electromigration.

On electrophoresis of a pH-regulated nanogel with ion partitioning effects.

The electrophoresis of a polyelectrolyte nanoparticle, whose charge condition depends on the salt concentration and pH of the suspended medium as well as the dielectric permittivity difference, is analyzed. The present nonlinear model for the electrophoresis of this pH-regulated polyelectrolyte (PE) particle is based on the consideration of full set of governing equations of fluid and ion transport coupled with the equation for electric field. The Born energy of the ions are incorporated to account for the difference in the dielectric permittivity of the PE and the electrolyte. The governing equations are computed numerically through a control volume approach. The nonlinear effects are highlighted by comparing with the existing linear model as well as results based on the first-order perturbation analysis valid for a weak applied field. The ion partitioning effect arising due to the difference in self energy of ions between the two media, have a strong impact on the mobility of the PE. The ion partitioning effect attenuates the penetration of counterions in the PE, which enhances the electric force and hence, results in a larger mobility of the PE. The nonlinear effects due to the double layer polarization and relaxation are intensified due to the ion partitioning effect. The ion partitioning effect influences the association/dissociation of PE functional group by tuning the hydrogen/hydroxide ions. Present study shows that the ion partitioning effect is profound for higher salt concentration and/or higher volume density of PE functional groups.

Optimization of background electrolyte composition for simultaneous contactless conductivity and fluorescence detection in capillary electrophoresis of biological samples.

In this article, optimization of BGE for simultaneous separation of inorganic ions, organic acids, and glutathione using dual C4 D-LIF detection in capillary electrophoresis is presented. The optimized BGE consisted of 30 mM 2-[4-(2-hydroxyethyl)piperazin-1-yl]ethanesulfonic acid, 15 mM 2-amino-2-hydroxymethyl-propane-1,3-diol, and 2 mM 18-crown-6 at pH 7.2 and allowed simultaneous separation of ten inorganic anions and cations, three organic acids and glutathione in 20 min. The samples were injected hydrodynamically from both capillary ends using the double-opposite end injection principle. Sensitive detection of anions, cations, and organic acids with micromolar LODs using C4 D and simultaneously glutathione with nanomolar LODs using LIF was achieved in a single run. The developed BGE may be useful in analyses of biological samples containing analytes with differing concentrations of several orders of magnitude that is not possible with single detection mode.

Botanical metabolite ions extraction from full electrospray ionization mass spectrometry using high-dimensional penalized regression.

INTRODUCTION: Mass spectrometric data analysis of complex biological mixtures can be a challenge due to its vast datasets. There is lack of data treatment pipelines to analyze chemical signals versus noise. These tasks, so far, have been up to the discretion of the analysts. OBJECTIVES: The aim of this work is to demonstrate an analytical workflow that would enhance the confidence in metabolomics before answering biological questions by serial dilution of botanical complex mixture and high-dimensional data analysis. Furthermore, we would like to provide an alternative approach to a univariate p-value cutoff from t-test for blank subtraction procedure between negative control and biological samples. METHODS: A serial dilution of complex mixture analysis under electrospray ionization was proposed to study firsthand chemical complexity of metabolomics. Advanced statistical models using high-dimensional penalized regression were employed to study both the concentration and ion intensity relationship and the ion-ion relationship per second of retention time sub dataset. The multivariate analysis was carried out with a tool built in-house, so called metabolite ions extraction and visualization, which was implemented in R environment. RESULTS: A test case of the medicinal plant goldenseal (Hydrastis canandensis L.), showed an increase in metabolome coverage of features deemed as "important" by a multivariate analysis compared to features deemed as "significant" by a univariate t-test. For an illustration, the data analysis workflow suggested an unexpected putative compound, 20-hydroxyecdysone. This suggestion was confirmed with MS/MS acquisition and literature search. CONCLUSION: The multivariate analytical workflow selects "true" metabolite ions signals and provides an alternative approach to a univariate p-value cutoff from t-test, thus enhancing the data analysis process of metabolomics.

Affinity Directed Surface Functionalization of Two Different Metal Nanoparticles by a Natural Ionophore: Probing and Removal of Hg2+ and Al3+ Ions from Aqueous Solutions.

In this work, we report affinity controlled surface modifications of two different metal nanoparticles (MNPs) using a hydrophilic natural ionophore (microbial chelator) aeruginic acid (abbreviated as H2L) that possesses two different types of binding pockets viz. O/O from carboxylic acid group and N/O from a phenol-thiazole moiety. Preferred binding of the former donor set (i.e., O/O) on to the surface of silver nanoparticles (AgNPs) has resulted in a colorimetric nanomaterial HL@AgNPs, which showed naked eye observable easy detection of Hg2+ in aqueous HEPES buffer at pH 7.4, even in the presence of other metal ions. On the other hand, excellent affinity of the phenol-thiazole moiety (i.e., N/O) for iron nanosurfaces (FeNPs) develops a fluorogenic nanomaterial HL@FeNPs. Brilliant emission behavior of this nanomaterial enabled it to be useful for highly selective recognition of Al3+ under identical experimental conditions. Remarkable fluorescence enhancement (122-folds) of HL@FeNPs upon addition of Al3+ remain unchanged even in the presence of other competing metal ions. The nanomaterials HL@AgNPs and HL@FeNPs could even detect the target analytes instantly offering lower detection limits of 2 and 80 nM, respectively. Presence of toxic metal ions as environmental pollutant demands for dual-functional materials capable of performing the task of probing cum removal. Surface functionalizations of the nanomaterials of silver and iron with H2L have also resulted two removal agents that can efficiently and easily extract Hg2+ and Al3+ ions from contaminated water, respectively. We are not aware of any work that highlights the manifold utilization of a microbial chelator (i.e., natural ionophore) in the facile construction of different metal nanoparticles for environmental applications such as detection cum removal of toxic metal ions from aqueous solutions.

Structural and positional impact on DNAzyme-based electrochemical sensors for metal ions.

The rapid, accurate and convenient detection of heavy metal is very important to public health. Here, we developed a DNAzyme-based electrochemical sensor for Pb2+. A DNAzyme-including and Pb2+ active probe was anchored to the biosensing interface, based on the well-defined self-assembled, three-dimensional DNA nanostructure. The results indicate that the detection performance depends on the change of distances between the methylene blue and the electrode surface. The limit of detection (LOD) could reach the concentration of 0.01 µM Pb2+, and the signal change shows semi-logarithmic relationship with the concentration of Pb2+ from 0.01 µM to 100 µM. The biosensor also presents good stability and specificity to detect Pb2+ in tap or river water. This method not only provides promising approach for improving the performance of tetrahedra in detecting Pb2+, but helps deepen the understanding of tetrahedral structure design and how the position of electroactive groups affects the performance of electrochemical sensing.

Functionalized graphene nanosheets as absorbent for copper (II) removal from water.

Functionalized graphene nanosheets (FGNs) with high surface area and various functional groups were prepared by oxidation method. The characteristics of FGNs were studied by nitrogen adsorption using the Brunauer-Emmett-Teller (BET) method, Fourier transform infrared spectroscopy (FTIR), transmission electron microscope (TEM), scanning electron microscope (SEM), energy dispersion spectrum (EDS), and atomic force microscopy (AFM). The specific surface area of obtained FGNs was measured as 834.06 m2 g-1, which was 20-40% higher than graphene nanosheets (GNs) before oxidation. An abundance of oxygen-containing functional groups, such as carboxyl, hydroxyl and epoxy groups, was grafted on the edge and surface of GNs. Moreover, FGNs demonstrated excellent adsorption and desorption performance when used as absorbent to remove Cu (II) from aqueous solution. The removal percentage could reach 96% within 1 h and remain 72% after 5 adsorption-desorption cycles. Adsorption process and mechanism were elucidated by kinetics models and isotherm models. The results showed FGNs has a great potential to be an adsorbent for removal copper ions from water.

The synergistic effect and microscopic mechanism of co-adsorption of three emerging contaminants and copper ion on gemini surfactant modified montmorillonite.

Montmorillonite (G-Mt) modified by a gemini quaternary ammonium cationic surfactant (Propyl bis (hexadecyl dimethyl ammonium) chloride, 16-3-16) was used to remove emerging contaminants (ECs) (such as 1H-Benzotriazole (BTA), 5-Methyl-1H-benzotriazole (TTA) and 1-Hydroxybenzotriazole (HOBT)) and Cu2+ from wastewater. Based on the adsorption of the above three ECs in our previous studies, single adsorption of Cu2+ and the simultaneous adsorption of three ECs with Cu2+ on G-Mt were also investigated. G-Mt showed much lower adsorption amount on Cu2+ comparing with original montmorillonite (Ca-Mt) in single adsorption system due to the difficulty of ion-exchange property of G-Mt. In co-adsorption system, three organic pollutants and Cu2+ played a synergistic effect and the adsorption capacity of G-Mt on them increased, the influence sequence of Cu2+ on the adsorption of three ECs or the effect of ECs on the adsorption of Cu2+ both followed as: TTA > BTA > HOBT. The results of FT-IR, EDS and XPS revealed that the complex of Cu2+ and ECs were adsorbed onto G-Mt via forming complexes and hydrophobic interaction in co-adsorption system. The pH experiment showed that the optimum pH of the co-adsorption of ECs and Cu2+ on G-Mt was 5. Molecular dynamics (MD) simulations showed that three ECs or ECs combining with Cu2+ were dominantly adsorbed in the interlayer space of G-Mt, which resulted in the arrangement manner of 16-3-16 between the layer of G-Mt before and after adsorption of three organic pollutants was different. Furthermore, by quantitatively analyzing electrostatic potential (ESP) distribution, average local ionization energy (ALIE) distribution and their minimum points on three ECs molecules surfaces, Multiwfn program has been applied to probe the microscopic mechanism. The synergistic effect of co-adsorption will promote enrichment of copper ions and ECs to remove them more efficiently in polluted waters.

Metal-organic framework-based materials: superior adsorbents for the capture of toxic and radioactive metal ions.

Highly efficient removal of metal ion pollutants, such as toxic and nuclear waste-related metal ions, remains a serious task from the biological and environmental standpoint because of their harmful effects on human health and the environment. Recently, highly porous metal-organic frameworks (MOFs), with excellent chemical stability and abundant functional groups, have represented a new addition to the area of capturing various types of hazardous metal ion pollutants. This review focuses on recent progress in reported MOFs and MOF-based composites as superior adsorbents for the efficient removal of toxic and nuclear waste-related metal ions. Aspects related to the interaction mechanisms between metal ions and MOF-based materials are systematically summarized, including macroscopic batch experiments, microscopic spectroscopy analysis, and theoretical calculations. The adsorption properties of various MOF-based materials are assessed and compared with those of other widely used adsorbents. Finally, we propose our personal insights into future research opportunities and challenges in the hope of stimulating more researchers to engage in this new field of MOF-based materials for environmental pollution management.