Analysis and health risk assessment of phthalate esters (PAEs) in indoor dust of preschool and elementary school centers in city of Tehran, Iran.

Individuals spend a lot of time indoors; thus they are generally exposed to phthalates used in consumer products. Therefore, those exposed to phthalates as indoor contaminants are at high risks. The present study was conducted to evaluate the carcinogenic and non-carcinogenic hazard of phthalate esters (PAEs), like dimethyl phthalate, diethyl phthalate, di(nbutyl) phthalate, butyl benzyl phthalate, dioctyl phthalate, and di(2-ethylhexyl) phthalate in the dust obtained from 21 schools in Tehran, in 2019. A total of 63 indoor dust specimens were obtained by a vacuum cleaner. After transferring dust samples to the laboratory, 100 mg of each sample was centrifuged and mixed with 20 ml acetone and kept through a night and ultrasonicated within 30 min. Eventually, PAEs' contents were measured via gas chromatography-mass spectrometry. Based on the findings, median concentrations of DMP, DEP, DnBP, BBP, DEHP, and DnOP were 0.90, 0.10, 6.0, 0.20, 118.30, and 4.10 mg kg-1 respectively. Moreover, the overall average daily exposure doses (ADD) of phthalate esters via dust ingestion, skin contact, and inhalation were 1.56E-03, 1.70E-06, and 1.56E-07 mg kg-1 day-1, respectively, and the lifetime average daily exposure doses (LADD) were 1.83E-04, 2.34E-08, and 2.46E-08 mg kg-1 day-1, respectively; thus ingestion of dust particles was found to be the main pathway of exposure to phthalate for non-carcinogenic and carcinogenic risks. Although based on the results, the studied samples were below the US Environmental Protection Agency threshold of 1.00E-06, due to the disadvantages of phthalates in human safety, these kinds of investigations are helpful in understanding the main ways of exposure to PAEs and providing a science-based framework for the future attempts for mitigating the PAEs indoor emissions.

Designing new biocompatible glass-forming Ti75-x Zr10 Nbx Si15 (x = 0, 15) alloys: corrosion, passivity, and apatite formation.

Glass-forming Ti-based alloys are considered as potential new materials for implant applications. Ti75 Zr10 Si15 and Ti60 Zr10 Nb15 Si15 alloys (free of cytotoxic elements) can be produced as melt-spun ribbons with glassy matrix and embedded single ß-type nanocrystals. The corrosion and passivation behavior of these alloys in their homogenized melt-spun states have been investigated in Ringer solution at 37°C in comparison to their cast multiphase crystalline counterparts and to cp-Ti and ß-type Ti-40Nb. All tested materials showed very low corrosion rates as expressed in corrosion current densities icorr < 50 nA/cm(2). Electrochemical and surface analytical studies revealed a high stability of the new alloys passive states in a wide potential range. This corresponds to low passive current densities ipass = 2 ± 1 µA/cm(2) based on the growth of oxide films with thickness d <10 nm. A homogeneous constituent distribution in the melt-spun alloys is beneficial for stable surface passivity. The addition of Nb does not only improve the glass-forming ability and the mechanical properties but also supports a high pitting resistance even at extreme anodic polarization up to 4V versus SCE were oxide thickness values of d ∼35 nm are reached. With regard to the corrosion properties, the Nb-containing nearly single-phase glassy alloy can compete with the ß-type Ti-40Nb alloy. SBF tests confirmed the ability for formation of hydroxyapatite on the melt-spun alloy surfaces. All these properties recommend the new glass-forming alloys for application as wear- and corrosion-resistant coating materials for implants.

Designing biocompatible Ti-based metallic glasses for implant applications.

Ti-based metallic glasses show high potential for implant applications; they overcome in several crucial respects their well-established biocompatible crystalline counterparts, e.g. improved corrosion properties, higher fracture strength and wear resistance, increased elastic strain range and lower Young's modulus. However, some of the elements required for glass formation (e.g. Cu, Ni) are harmful for the human body. We critically reviewed the biological safety and glass forming tendency in Ti of 27 elements. This can be used as a basis for the future designing of novel amorphous Ti-based implant alloys entirely free of harmful additions. In this paper, two first alloys were developed: Ti(75)Zr(10)Si(15) and Ti(60)Nb(15)Zr(10)Si(15). The overheating temperature of the melt before casting can be used as the controlling parameter to produce fully amorphous materials or bcc-Ti-phase reinforced metallic glass nano-composites. The beneficial effect of Nb addition on the glass-formation and amorphous phase stability was assessed by X-ray diffraction, transmission electron microscopy and differential scanning calorimetry. Crystallization and mechanical behavior of ribbons are influenced by the amount and distribution of the nano-scaled bcc phase existing in the as-cast state. Their electrochemical stability in Ringer's solution at 310 K was found to be significantly better than that of commercial Ti-based biomaterials; no indication for pitting corrosion was recorded.