RESUMO
Although various types of bifacial solar cells exist, few studies have been conducted on bifacial semitransparent CuInSe2 solar cells (BS-CISe SCs) despite the attractive potential in power generation from both sides in an albedo environment. The optimized BS-CISe SCs with 300 and 800 nm-thick absorber via a streamlined single-stage co-evaporation process exhibit a power conversion efficiency (PCE) of 6.32% and 10.6%, respectively. When double-sided total 2.0 sun illumination is assumed in an albedo environment, the bifacial power generation densities (BPGD) of them increases to 9.41% and 13.9%. Four-terminal bifacial semitransparent tandem solar cells (4T-BST SCs) are fabricated to increase the BPGD by mechanically stacking a BS-perovskite (PVK) top cell on top of a BS-CISe bottom cell with the 300 and 800 nm-thick absorber layers. When summed up, the best top and bottom cell PCEs of the 4T-BST SC with 300 and 800 nm-thick BS-CISe SC are 18.8% and 21.1%, respectively. However, the practical BPGD values of the 4T-BST SC under total 2 sun illumination are interestingly 23.4% and 24.4%, respectively. This is because the BS-CISe bottom cell's thickness affects how much rear-side illumination is transmitted to the BS-PVK top cell, increasing its current density and BPGD.
RESUMO
OBJECTIVE: Using medicinal plant by-products (MPBP) as feed additives may be an eco-friendly option as substitutes for feedstuffs and may assist in reducing the improper disposal of MPBP. Therefore, this study was conducted to evaluate the influences of MPBP on the meat quality of Hanwoo steers fed a total mixed ration (TMR). METHODS: Twenty seven steers (body weight = 573±57 kg) were randomly divided into three treatments with a control group and two tested groups as follows: control, 1,000 g/kg TMR; treatment 1 (MPBP30), 970 g/kg TMR and 30 g/kg MPBP; treatment 2 (MPBP50), 950 g/kg TMR and 50 g/kg MPBP. RESULTS: Average daily gain, feed conversion ratio and the Commission Internationale de l'Eclairage L* of muscle were improved (p<0.05, respectively) by MPBP30. Stearic acid (C18:0) was decreased (linear effect, p = 0.012), while oleic acid (C18:1) was increased (linear effect, p = 0.055) by MPBP level. Saturated fatty acid (SFA) and polyunsaturated fatty acid (PUFA) were decreased for MPBP50 while unsaturated fatty acid (USFA) and monounsaturated fatty acid (MUFA) were increased for MPBP 50. USFA and SFA ratio was increased for MPBP50 as well. CONCLUSION: These results indicated that MPBP supplementation in Hanwoo steers fed a TMR increased feed efficiency and meat color (lightness) with altering fatty acid proportions. Therefore, MPBP may be successfully used in ruminant feeding.
RESUMO
The efficiency of copper indium gallium selenide (CIGS) solar cells that use transparent conductive oxide (TCO) as the top electrode decreases significantly as the device area increases owing to the poor electrical properties of TCO. Therefore, high-efficiency, large-area CIGS solar cells require the development of a novel top electrode with high transmittance and conductivity. In this study, a microgrid/TCO hybrid electrode is designed to minimize the optical and resistive losses that may occur in the top electrode of a CIGS solar cell. In addition, the buffer layer of the CIGS solar cells is changed from the conventional CdS buffer to a dry-processed wide-band gap ZnMgO (ZMO) buffer, resulting in increased device efficiency by minimizing parasitic absorption in the short-wavelength region. By optimizing the combination of ZMO buffer and the microgrid/TCO hybrid electrode, a device efficiency of up to 20.5% (with antireflection layers) is achieved over a small device area of 5 mm × 5 mm (total area). Moreover, CIGS solar cells with an increased device area of up to 20 mm × 70 mm (total area) exhibit an efficiency of up to 19.7% (with antireflection layers) when a microgrid/TCO hybrid electrode is applied. Thus, this study demonstrates the potential for high-efficiency, large-area CIGS solar cells with novel microgrid electrodes.
RESUMO
This study evaluated the in vitro effect of medicinal plant extracts on ruminal methanogenesis, four different groups of methanogens and ruminal fermentation characteristics. A fistulated Holstein cow was used as a donor of rumen fluid. Licorice and mugwort extracts (Glycyrrhiza uralensis and Artemisia capillaris, 0.5% and 1% of total substrate DM, respectively), previously used as folk remedies, were added to an in vitro fermentation incubated with buffered-rumen fluid. Total gas production in Glycyrrhiza uralensis extract treatment was not significantly different between treatments (p<0.05) while total gas production in the Artemisia capillaris extract treatment was lower than that of the control. Artemisia capillaris extract and Glycyrrhiza uralensis extract reduced CH4 emission by 14% (p<0.05) and 8% (p<0.05), respectively. Ciliate-associated methanogens population decreased by 18% in the medicinal plant extracts treatments. Medicinal plant extracts also affected the order Methanobacteriales community. Methanobacteriales diversity decreased by 35% in the Glycyrrhiza uralensis extract treatment and 30% in the Artemisia capillaris extract treatment. The order Methanomicrobiales population decreased by 50% in the 0.5% of Glycyrrhiza uralensis extract treatment. These findings demonstrate that medicinal plant extracts have the potential to inhibit in vitro ruminal methanogenesis.
RESUMO
Among many building-integrated semitransparent photovoltaics (BISTPVs), semitransparent ultrathin (STUT) Cu(Inx ,Ga1-x )Se2 (CIGSe) solar cells are distinguishable due to their potential high power conversion efficiency (PCE) among other thin-film solar cells, versatile applicability based on thin film deposition processes, high stability consisting of all inorganic compositions, and practical expandability to bifacial applications. However, the fundamental trade-off relationship between PCE and transparency limits the performance of BISTPV because implementing a higher semitransparency lowers the optical budget of incoming light. To expand the available optical budget and to enhance the PCE while maintaining a suitable transparency in STUT CIGSe solar cell with single-stage coevaporated 500-nm-thick absorber, an atomic layer deposited wide bandgap Zn(O,S) buffer is introduced as the replacement of conventional CdS buffer, which partially limits incoming light less than 520 nm in wavelength. As a replacement result, more incoming light becomes valid for power conversion, and the short circuit current density (Jsc ) has increased comparatively by 17%, which has directly lead to a large increase in PCE up to 12.41%. Furthermore, Zn(O,S) buffer in the STUT CIGSe solar cell also has enhanced the bifacial compatible efficiency (BCE), which has increased to 14.44% at 1.3 sun and 19.42% at 2.0 sun.
RESUMO
Chalcopyrite-based materials for photovoltaic devices tend to exhibit complex structural imperfections originating from their polycrystalline nature; nevertheless, properly controlled devices are surprisingly irrelevant to them in terms of resulting device performances. The present work uses atom probe tomography to characterize co-evaporated high-quality Cu(In,Ga)Se2 (CIGS) films on flexible polyimide substrates either with or without doping with Na or doping with Na followed by K via a post-deposition treatment. The intent is to elucidate the unique characteristics of the grain boundaries (GBs) in CIGS, in particular the correlations/anti-correlations between matrix elements and the alkali dopants. Various compositional fluctuations are identified at GBs irrespective of the presence of alkali elements. However, [Cu-poor and Se/In,Ga-rich] GBs are significantly more common than [Cu-rich and Se/In,Ga-poor] ones. In addition, the anti-correlations between Cu and the other matrix elements are found to show not only regular trends among themselves but also the association with the degree of alkali segregation at GBs. The Na and K concentrations exhibited a correlation at the GBs but not in the intragrain regions. Density functional theory calculations are used to explain the compositional fluctuations and alkali segregation at the GBs. Our experimental and theoretical findings not only reveal the benign or beneficial characteristics of the GBs of CIGS but also provide a fundamental understanding of the GB chemistry in CIGS-based materials.
RESUMO
Control of the constituent phase and stoichiometry of iron pyrite (FeS2) is a prerequisite for high-performance photovoltaic devices based on this material. If the pyrite contains sulfur-deficiency-related secondary phases which have a metallic character and a high possibility of coexistence in pyrite films, then significant carrier recombination is expected. In this work, the beneficial role of Na in suppressing the formation of nanoscale or amorphous sulfur-deficient secondary phases is reported with experimental evidence, leading to a higher phase purity for solution-processed pyrite films. The potential reduction of charge recombination via these metallic secondary phases results in significant improvements in both the photopotential and photocurrent intensity of Na-modified pyrite films compared with reference samples.
RESUMO
A common feature of the inorganic thin films including Cu(In,Ga)(S,Se)2 fabricated by nonvacuum solution-based approaches is the doubled-layered structure, with a top dense inorganic film and a bottom carbon-containing residual layer. Although the latter has been considered to be the main efficiency limiting factor, (as a source of high series resistance), the exact influence of this layer is still not clear, and contradictory views are present. In this study, using a CISe as a model system, we report experimental evidence indicating that the carbon residual layer itself is electrically benign to the device performance. Conversely, carbon was found to play a significant role in determining the depth elemental distribution of final film, in which carbon selectively hinders the diffusion of Cu during selenization, resulting in significantly Cu-deficient top CISe layer while improving the film morphology. This carbon-affected compositional and morphological impact on the top CISe films is a determining factor for the device efficiency, which was supported by the finding that CISe solar cells processed from the precursor film containing intermediate amount of carbon demonstrated high efficiencies of up to 9.15% whereas the performances of the devices prepared from the precursor films with very high and very low carbon were notably poor.