Injectable Colloidal Hydrogels of N-Vinylformamide Microgels Dispersed in Covalently Interlinked pH-Responsive Methacrylic Acid-Based Microgels.

Injectable hydrogels offer great potential to augment damaged or degenerated soft tissues. A key criterion for such gels is that their modulus is as close as possible to that of the target tissue. The majority of synthetic hydrogels have used low molecular weight polymer chains which may cause problems if they diffuse away from the injection site and/or increase the local osmotic pressure. We previously introduced a different approach of injecting preformed ultra-high molecular weight pH-responsive microgels (MGs) that interlink to form hydrogels. MGs are crosslinked polymer colloid particles that swell when the pH approaches the particle pKa. These colloidal hydrogels are termed doubly crosslinked microgels (DX MGs). The gel moduli of previous DX MGs were much greater than that reported for human nucleus pulposus (NP) tissue of the spinal intervertebral disk. Here, we replace some of the pH-responsive poly(ethyl acrylate-co-methacrylic acid) (PEA-MAA) MGs with hydrophilic non-ionic MGs based on poly(N-vinylformamide) (NVF). We investigate the morphology and mechanical properties of these new injectable composite DX MGs and show that the mechanical properties can be tuned by systematically varying the NVF MG content. Using this approach, the gel moduli close to that for NP tissue are achieved. These injectable new pH-responsive gels exhibit low cytotoxicity. Our work provides a potential new system for minimally invasive intervertebral disk augmentation.

Structurally colored semitransparent perovskite solar cells using one-step deposition of self-ordering microgel particles.

Semitransparent perovskite solar cells (STPSCs) have excellent potential for widespread application as building integrated photovoltaics. Widespread application of STPSCs could result in decreased CO2 footprints for buildings. Unfortunately, STPSCs tend to have poor aesthetic qualities (being usually red-brown in color) and low stability. Building on our previous work, here we use new poly(N-isopropylacrylamide) microgels (PNP MGs) to provide highly ordered non-close packed arrays within perovskite films that reflect some of the incident light to provide structural color to STPSCs. (MGs are swellable crosslinked polymer colloid particles.) We introduce PNP MGs into two different perovskites and achieve a wide gamut of reflected color and iridescence from the perovskite films. Devices containing the MGs have average visible transparency (AVT) values of greater than 25%. The best PCE for a MG-containing STPSC is 10.60% compared to 9.14% for the MG-free control. The MGs not only introduce structural color to the STPSCs but increase the PCE and stability. Equations are provided that enable the reflected color to be predicted from the formulation used to deposit the films. Our work shows that the self-ordering tendency of PNP MGs gives a viable new method for introducing structural color into STPSCs. Because our one-step method for introducing structural color into STPSCs is general, does not introduce any additional processing steps and is scalable whilst also improving device stability, this study may bring deployment of STPSCs closer.

Improving the Efficiency, Stability, and Adhesion of Perovskite Solar Cells Using Nanogel Additive Engineering.

Additive engineering has been applied widely to improve the efficiency and/or stability of perovskite solar cells (PSCs). Most additives used to date are difficult to locate within PSCs as they are small molecules or linear polymers. In this work, we introduce, for the first time, carboxylic acid-functionalized nanogels (NGs) as additives for PSCs. NGs are swellable sub-100 nm gel particles. The NGs consist of poly(2-(2-methoxyethoxy) ethyl methacrylate)-co-methacrylic acid-co-ethylenegylcol dimethacrylate (PMEO2MA-MAA-EGD) particles prepared by a scalable synthesis, which have a diameter of 40 nm. They are visualized in the perovskite films using SEM and are located at the grain boundaries. X-ray photoelectron and FTIR spectroscopy reveal that the NGs coordinate with Pb2+ via the -COOH groups. Including the NGs within the PSCs increased the grain size, decreased nonradiative recombination, and increased the power conversion efficiency (PCE) to 20.20%. The NGs also greatly increase perovskite stability to ambient storage, elevated temperature, and humidity. The best system maintained more than 80% of its original PCE after 180 days of storage under ambient conditions. Tensile cross-cut tape adhesion tests are used to assess perovskite film mechanical integrity. The NGs increased both the adhesion of the perovskite to the substrate and the mechanical stability. This study demonstrates that NGs are an attractive alternative to molecularly dispersed additives for providing performance benefits to PSCs. Our study indicates that the NGs act as a passivator, stabilizer, cross-linker, and adhesion promoter.