Compounds based on iron mining tailing dams and activated carbon from macauba palm for removal of emerging contaminants and phosphate from aqueous systems.

In this work, an iron-rich residue, which is widely obtained as a by-product in the iron mining industry, and macauba endocarp, waste from the extraction of vegetable oil for the production of biofuels, were used in the preparation of different composites based on iron and carbon. The composites were obtained by manual grinding of the calcined iron residue and activated carbon prepared by the macauba endocarp followed by thermal treatment under nitrogen atmosphere. The effect of the thermal treatment was analyzed by Mössbauer spectroscopy and X-ray diffraction and showed that the increase in the treatment temperature promoted the formation of different reduced iron phases in the final composite, such as Fe3O4, FeO, and Fe0. These composites were used in a combined adsorption/oxidation process through photocatalysis to remove up to 93% of amoxicillin from aqueous phase. The formation of possible reaction intermediates was monitored by electrospray ionization mass spectrometry (ESI-MS) and a mechanism of amoxicillin degradation was proposed. Afterward, the Fe/C composites were conducted to evaluate the impact of several parameters on phosphate adsorption processes and showed a maximum adsorption capacity of 40.3 mg g-1. The adsorption capacity obtained for all the materials were greater than those found in the literature.

Temperature programmed CVD: a novel technique to investigate carbon nanotube synthesis on FeMo/MgO catalysts.

In this work, it is demonstrated how a novel technique based on temperature-programmed chemical vapor deposition (TPCVD) can be used to investigate the synthesis of carbon nanotubes (CNTs) from methane on a classic catalyst FeMo(x)/MgO (x = 0.07, 0.35 and 1.00). TPCVD monitors carbon deposition by measuring H2 formed during CH4 decomposition and affords information on the different catalytic species, deactivation process, reaction kinetics and carbon yields. The obtained results showed for FeMgO catalyst a simple TPCVD peak related to the production of carbon beginning at 760 degrees C with maximum at 800 degrees C followed by a rapid deactivation resulting in a low carbon yield. The addition of Mo to Fe/MgO catalyst completely changes the TPCVD profile with the formation of a new catalytic species active at temperatures higher than 900 degrees C, which is stable and continuously decomposes CH4 to produce high carbon yields. Raman, TG/DTG, Mössbauer, SEM, TEM, XRD and TPR analyses suggested that this active catalytic phase is likely related to Fe-Mo and Fe-Mo-C phases active to produce single wall and mainly multiwall carbon nanotubes.

Radiosensitizing effects of citrate-coated cobalt and nickel ferrite nanoparticles on breast cancer cells.

Aim: Evaluation of the biocompatibility and radiosensitizer potential of citrate-coated cobalt (cit-CF) and nickel (cit-NF) ferrite nanoparticles (NPs). Materials & methods: Normal fibroblast and breast cancer cells were treated with different concentrations of citrate-coated ferrite NPs (cit-NPs) and irradiated with a cobalt-60 source at doses of 1 and 3 Gy. After 24 h, cell metabolism, morphology alterations and nanoparticle uptake were evaluated. Results: Cit-CF and cit-NF NPs showed no toxicity to normal cells up to 250 and 100 µg.ml-1, respectively. Combination of cit-NP and ionizing radiation resulted in up to fivefold increase in the radiation therapeutic efficacy against breast cancer cells. Conclusion: Cit-CF and cit-NF NPs are suitable candidates for application as breast cancer cell radiosensitizers.

Efficient activation of peroxymonosulfate by composites containing iron mining waste and graphitic carbon nitride for the degradation of acetaminophen.

In this work, the potential to use an iron mining waste (IW), rich in α-Fe2O3 and α-FeOOH, for the development of composites based on graphitic carbon nitride (CN) is demonstrated. These materials were synthesized through a simple thermal treatment at 550 °C of a mixture containing melamine and different IW mass percentages, giving rise to the catalysts xIWCN (where x is related to the initial mass percentage of IW). The iron phases of the precursor were partially transformed throughout the formation of the composites, in such a way that a mixture of α-Fe2O3 and γ-Fe2O3 was observed in their final composition. Furthermore, structural defects were produced in the carbonaceous matrix of the materials, causing the fragmentation of g-C3N4 and an increase of surface area. The catalytic activities of these composites were evaluated in reactions of peroxymonosulfate activation for the degradation of paracetamol. Among these materials, the composite 20IWCN showed the best catalytic activity, being able to degrade almost 90 % of the total paracetamol in only 20 min of reaction. This catalyst also demonstrated high chemical stability, being successfully utilized in five consecutive reaction cycles, with negligible iron leaching.

Boron nitride nanotube@NiFe2O4: a highly efficient system for magnetohyperthermia therapy.

Aim: The field of nanotechnology promotes the development of innovative and more effective cancer therapies. This work is aimed to develop a hybrid system that combines the capacity of boron nitride nanotubes (BNNTs) to be internalized by tumor cells and the ability of nickel ferrite nanoparticles to efficiently release heat by induced AC magnetic heating. Materials & methods: The systems studied were characterized by using x-ray diffractometry, transmission electron microscopy, vibrating sample magnetometry and Mössbauer spectroscopy. Results: The ferrite nanoparticles attached to BNNT were able to achieve the required temperatures for magnetohyperthermia therapies. After cellular internalization, AC induced magnetic heating of BNNT@NiFe2O4 can kill almost 80% of Hela cells lineage in a single cycle. Conclusion: This system can be a highly efficient magnetohyperthermia agent in cancer therapy.

Nanocrystalline Transition-Metal Gallium Oxide Spinels from Acetylacetonate Precursors via Solvothermal Synthesis.

The synthesis of mixed-metal spinels based on substituted γ-Ga2O3 is reported using metal acetylacetonate precursors in solvothermal reactions with alcohols as solvents at 240 °C. New oxides of Cr, Mn and Fe have been produced, all of which are formed as nanocrystalline powders, as seen by high-resolution transmission electron microscopy (HR-TEM). The first chromium-gallium mixed oxide is thus formed, with composition 0.33Ga1.87Cr0.8O4 ( = vacant site). X-ray absorption near-edge spectroscopy (XANES) at the chromium K-edge shows the presence of solely octahedral Cr3+, which in turn implies a mixture of tetrahedral and octahedral Ga3+, and the material is stable on annealing to at least 850 °C. An analogous manganese material with average chemical composition close to MnGa2O4 is shown to contain octahedral Mn2+, along with some Mn3+, but a different inversion factor to materials reported by conventional solid-state synthesis in the literature, which are known to have a significant proportion of tetrahedral Mn2+. In the case of iron, higher amounts of the transition metal can be included to give an Fe:Ga ratio of 1:1. Elemental mapping using energy dispersive X-ray spectroscopy on the TEM, however, reveals inhomogeneity in the distribution of the two metals. This is consistent with variable temperature 57Fe Mössbauer spectroscopy that shows the presence of Fe2+ and Fe3+ in more than one phase in the sample. Variable temperature magnetisation and electron paramagnetic resonance (EPR) indicate the presence of superparamagnetism at room temperature in the iron-gallium oxides.

Organotin(IV) complexes of 2-pyridineformamide-derived thiosemicarbazones: antimicrobial and cytotoxic effects.

Reaction of n-butyltin trichloride [(n-Bu)SnCl(3)] with 2-pyridineformamide thiosemicarbazone (H2Am4DH) and its N(4)-methyl (H2Am4Me) and N(4)-ethyl (H2Am4Et) derivatives gave [(n-Bu)Sn(2Am4DH)Cl(2)] (1), [(n-Bu)Sn(2Am4Me)Cl(2)] (2), and [(n-Bu)Sn(2Am4Et)Cl(2)] (3). Thiosemicarbazones as well as their tin complexes are active as antimicrobials against the growth of Candida albicans and Salmonella typhimurium and were highly active against malignant glioblastoma. The cytotoxic activity of complexes 1-3 is similar. Among the studied compounds [(n-Bu)Sn(2Am4DH)Cl(2)] (1) was the most active as antiproliferative (cytostatic) agent. Thiosemicarbazones and their tin(IV) complexes proved to be more potent as cytotoxic agents than cisplatin. All the compounds were able to induce apoptosis.

Surface restructuring of red mud to produce FeO x (OH) y sites and mesopores for the efficient complexation/adsorption of ß-lactam antibiotics.

In this work, iron oxide in the red mud (RM) waste was restructured to produce mesopores with surface [FeO x (OH) y ] sites for the efficient complexation/adsorption of ß-lactam antibiotics. Red mud composed mainly by hematite was restructured by an acid/base process followed by a thermal treatment at 150-450 °C (MRM150, MRM200, MRM300, and MRM450) and fully characterized by Mössbauer, XRD, FTIR, BET, SEM, CHN, and thermogravimetric analyses. The characterization data showed a highly dispersed Fe3+ oxyhydroxy phase, which was thermally dehydrated to a mesoporous α-Fe2O3 with surface areas in the range of 141-206 m2 g-1. These materials showed high efficiencies (21-29 mg g-1) for the adsorption of ß-lactam antibiotics, amoxicillin, cephalexin, and ceftriaxone, and the data was better fitted by the Langmuir model isotherm (R 2 = 0.9993) with monolayer adsorption capacity of ca. 39 mg g-1 for amoxicillin. Experiments such as competitive adsorption in the presence of phosphate and H2O2 decomposition suggested that the ß-lactamic antibiotics might be interacting with surface [FeO x (OH) y ] species by a complexation process. Moreover, the OH/Fe ratio, BET surface area and porosity indicated that this complexation is occurring especially on [FeO x (OH) y ]surf sites contained in the mesopore space.

Magnetic nanoparticles coated with cyclodextrins and citrate for irinotecan delivery.

In the present work, we study the role of different components in the formation of more stable iron oxide magnetic nanoparticles (MNPs): ß-cyclodextrin (BCD), 2-hydroxypropyl-ß-cyclodextrin (HP) and citrate anion. MNPs formulations were characterized by FTIR, particles size measurements, zeta potential based on dynamic light scattering principle technique, X-ray powder pattern diffraction, XPS spectroscopy, transmission electron microscopy and thermogravimetric analysis. The results showed that cyclodextrins and citrate plays a key role in order to obtain a lower size of coated MNPs and proved to be an efficient strategy to obtain a more stable colloidal dispersion, avoiding the nanoparticles oxidation, enhancing the irinotecan incorporation and release. Furthermore, citrate-coated BCD-MNPs showed the same cytotoxicity of the free IRI.

Magnetic iron species highly dispersed over silica: use as catalysts for removal of pollutants in water.

Fe2O3-SiO2 composites were prepared by impregnation (sample FeIMP) or doping (sample FeDOP) in the structure of porous silica. The dye removal capacity of the materials was investigated through adsorption and oxidation studies of methylene blue and rhodamine B. N2 adsorption/desorption measurements on FeIMP and FeDOP resulted in specific areas of 27 and 235 m2 g-1, respectively. Mössbauer spectroscopy and XRD data detected hematite and maghemite as the iron phases in the samples FeIMP and FeDOP, respectively. Adsorption isotherms and kinetic studies of the dyes were better fitted in DKR model for FeDOP, where the process follows a pseudo-second order with the interparticle diffusion step being the rate-limiting step. On the other hand, FeIMP has better fit in the Langmuir model. Photocatalytic activity was observed in FeDOP under UV irradiation by the presence of reaction-hydroxylated intermediates for MB (m/z = 301) and RhB (m/z = 459). However, the photocatalytic activity was strongly influenced by the adsorption affinity between dye/catalyst. Photogenerated holes are the species responsible for the dye degradation when the adsorption is too strong, while hydroxyl radical action will be favored when the adsorption is not vigorous as detected by ESI-MS. Graphical Abstract Action of photogenerated holes and free electrons into the photocatalytically mechanism of methylene blue degradation over a semiconductor.

Role of [FeOx(OH)y] surface sites on the adsorption of ß-lactamic antibiotics on Al2O3 supported Fe oxide.

In this work, [FeOx(OH)y]/Al2O3 composites with different Fe oxyhydroxy contents, i.e. 10, 20 and 50wt% treated at 150, 200, 300 and 450°C were investigated as adsorbents of ß-lactamic antibiotics, i.e. cephalexin, ceftriaxone and especially amoxicillin, from aqueous solutions. The obtained results showed that the nature of the surface Fe(3+) species play a fundamental role on the adsorption process. The most efficient adsorption was obtained for the sample 150Fe50A (50% [FeOx(OH)y] supported in Al2O3 treated at 150°C) whereas the thermal treatment at higher temperatures caused a strong decrease on the adsorption capacity. Mössbauer, XRD, FTIR, Raman, TG-MS, SEM, CHN and BET of the composite 150Fe50A suggested an approximate composition of FeO0.65(OH)1.7 whereas at 450°C strong dehydroxylation process takes place to form FeO1.4(OH)0.21. These results combined with competitive adsorption using amoxicillin mixed with phosphate or H2O2 suggest that the antibiotic molecules adsorb by complexation on surface sites likely based on FeOx(OH)y by the replacement of the labile OH ligands.

Growth of carbon structures on chrysotile surface for organic contaminants removal from wastewater.

Amphiphilic magnetic composites were produced based on chrysotile mineral and carbon structures by chemical vapor deposition at different temperatures (600-900 °C) and cobalt as catalyst. The materials were characterized by elemental analysis, X-ray diffraction, vibrating sample magnetometry, adsorption and desorption of N2, Raman spectroscopy, scanning electronic microscopy, and thermal analysis showed an effective growth of carbon structures in all temperatures. It was observed that at 800 and 900 °C, a large amount of carbon structures are formed with fewer defects than at 600 and 700 °C, what contributes to their stability. In addition, the materials present magnetic phases that are important for their application as catalysts and adsorbents. The materials have shown to be very active to remove the oil dispersed in a real sample of emulsified wastewater from biodiesel production and to remove methylene blue by adsorption and oxidation via heterogeneous Fenton mechanism.

Efficient use of Fe metal as an electron transfer agent in a heterogeneous Fenton system based on Fe0/Fe3O4 composites.

In this work a novel heterogeneous Fenton system based on Fe(0)/Fe3O4 composites is described. The composites with several Fe(0)/Fe3O4 ratios were prepared by two different methods, i.e. mechanical alloying of Fe(0) and Fe3O4 powders and controlled reduction of Fe3O4 with H2. Reaction studies and detailed Conversion Electron Mössbauer surface characterization of the composites Fe(0)/Fe3O4, Fe(0), Fe3O4, alpha-Fe2O3 and gamma-Fe2O3 suggested that Fe2+surf species are essential to produce an active Fenton system. Kinetic studies for the oxidation of the dye methylene blue, used as an organic model molecule, and for the peroxide decomposition suggest that the reactions proceed via HO* radicals generated from Fe2+surf species and H2O2 in a Fenton like mechanism. The increase in activity caused by the addition of Fe(0) is discussed in terms of a creation of Fe2+surf species during the preparation of the composite and by an electron transfer mechanism from Fe(0) to Fe3+surf during the Fenton reaction to regenerate the Fe2+surf active species.

Steel wastes as versatile materials for treatment of biorefractory wastewaters.

Recent research on novel cost-effective adsorbent materials suggests potential use of industrial wastes for effluent treatment, with the added benefit of reuse of the wastes. Waste steel materials, including blast oxygen furnace sludge (BOFS), blast furnace sludge (BFS), and blast furnace dust (BFD), were investigated as low-cost adsorbents for removal of an oil emulsion and RR195 dye. The residues were characterized by X-ray diffraction, Brunauer-Emmett-Teller area, volume and distribution of pore diameters, Mössbauer spectroscopy, X-ray fluorescence, granulometry, scanning electron microscopy/energy dispersive spectroscopy, and pHpzc. Adsorption kinetics data were obtained by UV-vis spectrophotometry at the maximum absorption wavelength of the dye solution and crude oil emulsion. The use of waste as an adsorbent was more efficient for treatment of the oil emulsion than the dye solution. BOFS had higher total organic carbon (TOC) removal efficiency than the other waste materials. For the RR195 dye, good color removal was observed for all adsorbents, >90 % within 24 h. TOC removal was poor, <10 % for BFD and BFS and a maximum of 37 % for BOFS. For the oil emulsion, 97 % TOC removal was obtained by adsorption onto BOFS and 87 % onto BFS.

Origin of the large dispersion of magnetic properties in nanostructured oxides: Fe(x)O/Fe3O4 nanoparticles as a case study.

The intimate relationship between stoichiometry and physicochemical properties in transition-metal oxides makes them appealing as tunable materials. These features become exacerbated when dealing with nanostructures. However, due to the complexity of nanoscale materials, establishing a distinct relationship between structure-morphology and functionalities is often complicated. In this regard, in the FexO/Fe3O4 system a largely unexplained broad dispersion of magnetic properties has been observed. Here we show, thanks to a comprehensive multi-technique approach, a clear correlation between the magneto-structural properties in large (45 nm) and small (9 nm) FexO/Fe3O4 core/shell nanoparticles that can explain the spread of magnetic behaviors. The results reveal that while the FexO core in the large nanoparticles is antiferromagnetic and has bulk-like stoichiometry and unit-cell parameters, the FexO core in the small particles is highly non-stoichiometric and strained, displaying no significant antiferromagnetism. These results highlight the importance of ample characterization to fully understand the properties of nanostructured metal oxides.

Efficient and versatile fibrous adsorbent based on magnetic amphiphilic composites of chrysotile/carbon nanostructures for the removal of ethynilestradiol.

In this work, chrysotile was used as support to grow carbon nanotubes and nanofibers to produce fibrous amphiphilic magnetic nanostructured composites. Iron impregnated on the chrysotile surface at 1, 5 and 15 wt% was used as catalyst to grow carbon nanostructures by CVD (chemical vapor deposition) with ethanol at 800°C. Raman, TG/DTA, Mössbauer, XRD, BET, SEM, TEM, elemental analyses and contact angle measurements suggested the formation of a complex amphiphilic material containing up to 21% of nanostructured hydrophobic carbon supported on hydrophilic Mg silicate fibers with magnetic Fe cores protected by carbon coating. Adsorption tests for the hormone ethynilestradiol (EE), a hazardous water contaminant, showed remarkable adsorption capacities even compared to high surface area activated carbon and multiwall carbon nanotubes. These results are discussed in terms of the hydrophobic surface of the carbon nanotubes and nanofibers completely exposed and accessible for the adsorption of the EE molecules combined with the hydrophilic Mg silicate surface which allows good dispersion in water. The composites are magnetic and after adsorption the dispersed particles can be removed by a simple magnetic process. Moreover, the fibrous composites can be conformed as threads, screens and pellets to produce different filtering media.

Design, structural and spectroscopic elucidation, and the in vitro biological activities of new diorganotin dithiocarbamates.

The reaction of 2,2-dimethoxy-N-methylethyllamine or 2-methyl-1,3-dioxolane with CS(2) in alkaline media produced two novel dithiocarbamate salts. Subsequent reactions with organotin halides yielded six new complexes: [SnMe(2){S(2)CNR(R(1))(2)}(2)] (1), [Sn(n-Bu)(2){S(2)CNR(R(1))(2)}(2)] (2), [SnPh(2){S(2)CNR(R(1))(2)}(2)] (3), [SnMe(2){S(2)CNR(R(2))(2)}(2)] (4), [Sn(n-Bu)(2){S(2)CNR(R(2))(2)}(2)] (5), [SnPh(2){S(2)CNR(R(2))(2)}(2)] (6), where R = methyl, R(1) = CH(2)CH(OMe)(2), and R(2) = 2-methyl-1,3-dioxolane. All compounds were identified in terms of infrared, (1)H and (13)C NMR, and the complexes were also characterized using (119)Sn NMR, (119)Sn Mössbauer and X-ray crystallography. The biological activity of all derivatives has been screened in terms of IC(90) and IC(50) against Aspergillus flavus, Aspergillus niger, Aspergillus parasiticus, Penicillium citrinum, Curvularia senegalensis, Staphylococcus aureus, Listeria monocytogenes, Bacillus cereus, Streptococcus sanguinis, Escherichia coli, Citrobacter freundii, Salmonella typhimurium, and Pseudomonas aeruginosa and the results correlated well with a performed study of structure-activity relationship (SAR). Complexes (3), (5) and (6) displayed the best IC(90) and IC(50) in the presence of the fungi, greater than that of miconazole, used as control drug.

Hybrid magnetic amphiphilic composites based on carbon nanotube/nanofibers and layered silicates fragments as efficient adsorbent for ethynilestradiol.

In this work, hybrid magnetic amphiphilic composites were prepared by the catalytic growth of carbon nanotubes (CNTs) and nanofibers CNF on layered silicates fragments. SEM, TEM, Raman, XRD, Mössbauer, TG/DTA showed that CVD with CH(4) at 800°C produced CNF and magnetic Fe cores fixed on the surface of microfragments of silicates layers. Due to the amphiphilic character, the composites can be easily dispersed in water and efficiently adsorb hydrophobic contaminant molecules. For example, the composites showed remarkable adsorption capacities for the hormone ethinylestradiol, e.g. 2-4 mg m(-2), compared to ca. 0.1 mg m(-2) obtained for high surface area activated carbon and multiwall CNT. These results are discussed in terms of a high hydrophobic exposed surface area of the CNT and CNF fixed on the layered silicates fragments surface. Moreover, the composites can be easily removed from water by a simple magnetic separation process.

Potential of modified iron-rich foundry waste for environmental applications: Fenton reaction and Cr(VI) reduction.

A magnetic fraction (15%) from a waste of foundry sand (WFS), composed of sand, carbon, bentonite clay and iron (10%) was modified by thermal treatment at 400, 600 and 800°C under inert atmosphere. Mössbauer analyses showed that the thermal treatment increased the amount of Fe(3)O(4) from 25 to 55% by reduction of Fe(2)O(3) and highly dispersed Fe(3+) by the carbon present in the waste. The Fe(3)O(4) caused a significant increase on the activity of two important reactions with application in environmental remediation: the Fenton oxidation of indigo carmine dye with H(2)O(2) and the reduction of Cr(VI) to Cr(III). The magnetic fraction of WFS was also mixed with hematite (Fe(2)O(3)) and thermally treated at 400, 600 and 800°C. This treatment produced large amounts of surface Fe(3)O(4) and increased substantially the rate of Fenton reaction as well as Cr(VI) reduction. This reactivity combined with the presence of carbon (an adsorbent for organic contaminants), bentonite clay (an adsorbent for metallic contaminants) and the granulometry/packing/hydrodynamic features make WFS a promising material for use in reactive permeable barriers.

Controlled reduction of red mud waste to produce active systems for environmental applications: heterogeneous Fenton reaction and reduction of Cr(VI).

In this work, controlled reduction of red mud with H(2) was used to produce active systems for two different environmental applications, i.e. the heterogeneous Fenton reaction and the reduction of Cr(VI). Mössbauer, powder X-ray diffraction, thermal analyses and scanning electron microscopy analyses showed that at different temperatures, i.e. 300, 400, 500 and 600 degrees C, H(2) reduces red mud to different phases, mainly Fe(3)O(4), Fe(0)/Fe(3)O(4) and Fe(0). These Fe phases are dispersed on Al, Si and Ti oxides present in the red mud and show high reactivity towards two environmental applications, i.e. the heterogeneous Fenton reaction and the reduction of Cr(VI). Reduction with H(2) at 400 degrees C showed the best results for the oxidation of the model dye methylene blue with H(2)O(2) at neutral pH due to the presence of the composite Fe(0)/Fe(3)O(4). The reduced red mud at 500-600 degrees C produced Fe(0) highly active for the reduction of Cr(VI) in aqueous medium. Another feature of these red mud based system is that after deactivation due to extensive use they can be completely regenerated by simple treatment with H(2).