Improved cooling of photovoltaic panels by natural convection flow in a channel with adiabatic extensions.

In hot dry regions, photovoltaic modules are exposed to excessive temperatures, which leads to a drop in performance and the risk of overheating. The present numerical study aims to evaluate the natural air cooling of PV modules by an inclined chimney mounted at the back. The basic equations were solved using the finite volume method. The validity of the model is verified by comparison with the data available in the literature. Thermal and dynamic flow patterns are analyzed for a variety of parameters: Rayleigh numbers from 102 to 106, PV panel tilt angle from 15° to 90°, and channel aspect ratios from 1/20 to 1/5. A critical aspect ratio has been determined to minimize overheating of the PV module. According to the computational results, the tilt angle and modified Rayleigh number increase the mass flow rate and mean Nusselt number. The overheating zone with maximum temperatures is located in the upper part of the photovoltaic panel. The addition of an extension to both channel's inlet and outlet was found to improve the cooling of the photovoltaic panels; however, only the extensions downstream of the channel are truly effective. The critical lengths at which channel performance improves significantly were identified by examining the impact of longer extensions on channel performance. Increasing the extension length from 0 to 3H improves the mass flow rate by 65%, the average Nusselt number by 13.4%, and leads to an 11% decrease in maximum temperature when Ra* = 106. This cooling technique is particularly promising for hot dry regions where water is scarce.

Expression of concern: High performance flexible supercapacitors based on secondary doped PEDOT-PSS-graphene nanocomposite films for large area solid state devices.

Expression of concern for 'High performance flexible supercapacitors based on secondary doped PEDOT-PSS-graphene nanocomposite films for large area solid state devices' by Syed Khasim et al., RSC Adv., 2020, 10, 10526-10539, https://doi.org/10.1039/D0RA01116A.

Effects of nonlinear thermal radiation on the efficiency of building integrated photovoltaic systems with nanofluid cooling.

The nonlinear effects of thermal radiation on the free convection flow of certain nanofluids along a heated wall are studied numerically using an original finite-difference method. Nanofluids are used to improve the performance of flat and curved integrated photovoltaic modules. The partial differential equations governing the flow are difficult to solve due to the strong non-linearity of the radiative term. In contrast to previous studies, the problem is solved directly without linearization by Rosseland's nonlinear approximation. The proposed numerical method is validated with results from the literature. The effects of nonlinearity and various physical parameters such as time, volume fraction and radiation parameter on the velocity, temperature, Nusselt number and skin friction coefficient of the CuO-water nanofluid are analyzed and presented graphically. A comparative study between the solutions given by the linear and non-linear problems reveals that Rosseland's linear approximation is no longer valid when the effect of thermal radiation is significant. On the other hand, the non-linear model better reflects the physical phenomena involved in the cooling process. Finally, a comparison of the performance of five nanofluids (CuO, Ag, Al2O3, Cu and TiO2 in water) shows that the Cu-water nanofluid performs best, with a high heat transfer rate and low shear stresses.

The Hydrothermal-Assisted Approach Improves the Photocatalytic and Energy Storage Performance of Novel CuSe-TiO2-GO Composite.

This study reports a novel CuSe-TiO2-GO composite, synthesized by a facile hydrothermal method at a controlled temperature, and investigates its electrochemical performance for supercapacitors (SCs) and photocatalytic behavior for degrading methylene blue (MB) dye. The compositional phase structure and chemical bond interaction were thoroughly investigated. The as-fabricated pristine, binary, and ternary composites underwent comprehensive characterization employing spectroscopic techniques and electrochemical analysis. Compared with pure and binary compounds (CuSe, TiO2, and binary CuSe-TiO2 composites), the ternary CuSe-TiO2-GO composites demonstrated a high degradation efficiency while degrading MB in less than just 80 min (240 min, 100 min, and 140 min, respectively). The photocatalytic activity of the ternary CuSe-TiO2-GO composites is enhanced due to the highly positive conduction band of CuSe, leading to the quick excitation of electrons to the conduction band of CuSe. Subsequently, graphene oxide (GO) left holes on the photocatalyst surface for MB, as GO assisted the photoexcited electron-hole pairs, resulting in enhanced photocatalytic performance. The CuSe-TiO2-GO electrode for the supercapacitor indicates a 310.6 F/g and 135.2 F/g capacitance when the discharge current upsurges from 1 to 12 A/g. The good photocatalytic and energy storage performance is due to the smaller charge transfer resistance, which promotes efficient separation of electron-hole pairs.

Onsite enhancement of REEEC solar photovoltaic performance through PCM cooling technique.

The efficiency of solar panels decreases as the temperature increases and heat dissipation becomes a serious problem in hot environments such as the Arabian desert. This paper investigates the use of a phase change material (PCM-OM37P) to maintain panel temperatures close to ambient. The enhancement of the GCL-P6/60265W solar panel efficiency was demonstrated at the University of Tabuk Renewable Energy and Energy Efficiency Center (REEEC). As these solar panel arrays are remotely monitored, we were able to demonstrate the validity of our cooling solution. During peak times, a drop voltage of at least 0.6V has been realized using the PCM for cooling the PV panel. This corresponds to a cooling temperature of 5 to 6°C. This difference in operating voltages between the PCM-cooled and the reference PV panels translates into a power enhancement percentage (PEP) of about 3%. The PEP value was underestimated due to the PV string configuration where the operating electrical current is taken as the average value for both PV panels.

Expression of concern: Design and development of highly sensitive PEDOT-PSS/AuNP hybrid nanocomposite-based sensor towards room temperature detection of greenhouse methane gas at ppb level.

Expression of concern for 'Design and development of highly sensitive PEDOT-PSS/AuNP hybrid nanocomposite-based sensor towards room temperature detection of greenhouse methane gas at ppb level' by Syed Khasim et al., RSC Adv., 2021, 11, 15017-15029. DOI https://doi.org/10.1039/D1RA00994J.

Enhanced and Proficient Soft Template Array of Polyaniline-TiO2 Nanocomposites Fibers Prepared Using Anionic Surfactant for Fuel Cell Hydrogen Storage.

Porous TiO2-doped polyaniline and polyaniline nanocomposite fibers prepared by the in situ polymerization technique using anionic surfactant in an ice bath were studied. The prepared nanocomposites were characterized by FTIR spectroscopy and XRD patterns for structural analysis. The surface morphology of the polyaniline and its nanocomposites was examined using SEM images. DC conductivity shows the three levels of conductivity inherent in a semiconductor. Among the nanocomposites, the maximum DC conductivity is 5.6 S/cm for 3 wt.% polyaniline-TiO2 nanocomposite. Cyclic voltammetry shows the properties of PANI due to the redox peaks of 0.93 V and 0.24 V. Both peaks are due to the redox transition of PANI from the semiconductor to the conductive state. The hydrogen absorption capacity is approximately 4.5 wt.%, but at 60 °C the capacity doubles to approximately 7.3 wt.%. Conversely, 3 wt.% PANI-TiO2 nanocomposites have a high absorption capacity of 10.4 wt.% compared to other nanocomposites. An overall desorption capacity of 10.4 wt.% reduced to 96% was found for 3 wt.% TiO2-doped PANI nanocomposites.

Preparation of Anionic Surfactant-Based One-Dimensional Nanostructured Polyaniline Fibers for Hydrogen Storage Applications.

Polyaniline fibers were prepared in the presence of anionic surfactant in an ice medium to nucleate in one dimension and were compared to bulk polyaniline prepared at an optimum temperature. Fourier-transform infrared spectroscopy (FTIR) and X-ray powder diffraction (XRD) were used to investigate the structural analysis of the prepared samples. A conductivity study reveals that polyaniline fibers have high conductivity compared to bulk polyaniline. Hydrogen storage measurements confirm that the polyaniline fibers adsorbed approximately 86% of the total actual capacity of 8-8.5 wt% in less than 9 min, and desorption occurs at a lower temperature, releasing approximately 1.5 wt% of the hydrogen gases when the pressure is reduced further to 1 bar.

Fabrication and Characterization of Flexible Solid Polymers Electrolytes for Supercapacitor Application.

In this work, solid flexible polymer blend electrolytes (PBE) composed of polyvinyl alcohol (PVA) and polyvinyl pyrrolidone (PVP) with different amounts of sodium thiocyanate (NaSCN) salt mixed in double-distilled water (solvent) are prepared via solution casting method. The obtained films are characterized using several techniques. The study of the surface morphology of the polymer blend salt complex films via the POM technique reveals the presence of amorphous regions due to the NaSCN effect. FTIR spectra studies confirm the complex formation between PVA, PVP, and NaSCN. The addition of 20 wt% NaSCN salt in the composition PVA: PVP (50:50 wt%) polymer blend matrix leads to an increase in the number of charge carriers and thus improves the ionic conductivity. The ionic conductivity of each polymer blend electrolyte was studied using the electrochemical impedance spectroscopy (EIS) method. The highest room temperature ionic conductivity of 8.1 × 10-5 S/cm S cm-1 is obtained for the composition of PVA: PVP (50:50 wt%) with 20 wt% NaSCN. LSV test shows the optimized ion-conducting polymer blend electrolyte is electrochemically stable up to 1.5 V. TNM analysis reveals that 99% of ions contribute for the conductivity against 1% of electrons only in the highly conductive polymer electrolyte PVA: PVP (50:50 wt%) + 20 wt% NaSCN. A supercapacitor device was fabricated using the optimized ion-conducting polymer blend film and graphene oxide (GO) coated electrodes. The GCD curve clearly reveals the behavior of an ideal capacitor with less Faradic process and low ESR value. The columbic efficiency of the GO-based system is found to be 100%, the GO-based electrode exhibits a specific capacitance of 12.15 F/g and the system delivers the charge for a long duration. The specific capacitance of the solid-state supercapacitor cell was found to be 13.28 F/g via the CV approach close to 14.25 F/g obtained with EIS data at low frequency.

Thermal effect on curved photovoltaic panels: Model validation and application in the Tabuk region.

This paper aimed to investigate the temperature effect on photovoltaic (PV) cell parameters. The PV cell parameters such as series and parallel resistances, diode ideality factor, and diode saturation current, are not considered in the reported stepwise modeling. The present work aims to improve available models used in the modeling and simulation of PV modules to support the researcher and power project developer. All the required temperature-dependent parameters are determined to model the simulated PV module with high accuracy using Simulink/MATLAB software. To validate the method, a 36-cell-50W solar panel with different radii of curvature is set up to assess solar power outputs under varying irradiance and temperature conditions. For the present application, the Tabuk region (Saudi Arabia) is chosen based on its location and climatic conditions. The method provided conformity to the measured power outputs for varying Global Horizontal Irradiance (GHI) and temperature conditions. The maximum power output of the PV module increases from 14.4 W to 25.8 W when the received solar power density varies from 307 W/m2 to 526 W/m2 depending on the level of curvature starting from a semi-cylindrical shape to a vaulted shape to a flat shape. The curved PV module shows slightly higher power variation with temperature as compared to the flat one. Above 25°C, the power output is about 20% less at a maximum temperature of 65°C. When the temperature drops below 25°C, the power outputs increase about 6% and 11.5% for corresponding temperatures of 15°C and 5°C, respectively.

The Impact of Polymer Electrolyte Properties on Lithium-Ion Batteries.

In recent decades, the enhancement of the properties of electrolytes and electrodes resulted in the development of efficient electrochemical energy storage devices. We herein reported the impact of the different polymer electrolytes in terms of physicochemical, thermal, electrical, and mechanical properties of lithium-ion batteries (LIBs). Since LIBs use many groups of electrolytes, such as liquid electrolytes, quasi-solid electrolytes, and solid electrolytes, the efficiency of the full device relies on the type of electrolyte used. A good electrolyte is the one that, when used in Li-ion batteries, exhibits high Li+ diffusion between electrodes, the lowest resistance during cycling at the interfaces, a high capacity of retention, a very good cycle-life, high thermal stability, high specific capacitance, and high energy density. The impact of various polymer electrolytes and their components has been reported in this work, which helps to understand their effect on battery performance. Although, single-electrolyte material cannot be sufficient to fulfill the requirements of a good LIB. This review is aimed to lead toward an appropriate choice of polymer electrolyte for LIBs.

Design and development of highly sensitive PEDOT-PSS/AuNP hybrid nanocomposite-based sensor towards room temperature detection of greenhouse methane gas at ppb level.

Herein, we present fabrication of a novel methane sensor based on poly (3,4-ethylenedioxythiophene:poly (styrene sulfonic acid)) (p-PEDOT-PSS) and gold nanoparticles (AuNPs) treated with dimethyl sulfoxide (DMSO) and Zonyl using a spin coating technique. The nanocomposite films were further post treated with H2SO4 to improve the charge transport mechanism. The structural and morphological features of the composites were analyzed through scanning electronic microscopy, transmission electron microscopy, Fourier transform infra-red spectroscopy, UV-Vis spectroscopy and thermogravimetric analysis. Treatment with organic solvents and post treatment of H2SO4 significantly enhances the conductivity of the composite to 1800 S cm-1. The fabricated sensor shows an excellent sensing response, fast response and recovery time along with acceptable selectivity towards methane gas at ppb concentrations. Due to a simple fabrication technique, excellent conductivity, superior sensing performance and improved mechanical properties, the sensor fabricated in this study could potentially be used to detect greenhouse methane gas at low concentrations.

High performance flexible supercapacitors based on secondary doped PEDOT-PSS-graphene nanocomposite films for large area solid state devices.

In this work, we propose the development of high performance and flexible supercapacitors using reduced graphene oxide (rGO) incorporated poly(3,4 ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT-PSS) nanocomposites by secondary doping. The structural and morphological features of the composite film were analyzed in detail using SEM, AFM, FTIR, XPS and TGA. Secondary doping of ethylene glycol (EG) assisted by rGO incorporation significantly enhances the room temperature conductivity of PEDOT-PSS films from 3 S cm-1 to nearly 1225 S cm-1 for a 10 wt% composite. The secondary doped PEDOT-PSS:EG/rGO composite film demonstrated improved electrochemical performances with specific capacitance of 174 (F g-1) and energy density of 810 (W h kg-1) which is nearly 4 times greater than pristine PEDOT-PSS due to synergetic interactions between rGO and PEDOT-PSS. The prepared composite films show long term stability with capacitance retention of over 90% after 5000 cycles of charging-discharging. The nanocomposite films used in the present investigation demonstrates percolative behavior with a percolation threshold at 10 wt% of rGO in PEDOT-PSS. The assembled supercapacitor device could be bent and rolled-up without a decrease in electrochemical performance indicating the potential to be used in practical applications. To demonstrate the practical applicability, a rolled-up supercapacitor device was constructed that demonstrates operation of a red LED for 40 seconds when fully charged. This study will provide new dimensions towards designing cost effective, flexible and all solid-state supercapacitors with improved electrochemical performance using electrodes based on secondary doped PEDOT-PSS/rGO organic thin films.

Synthesis and characterization of HDPE/N-MWNT nanocomposite films.

In this work, a series of nitrogen-doped multi-walled carbon nanotubes (N-MWCNTs) with several weight percentages (0.1, 0.4, 0.8, and 1.0 wt.%) were synthesized by catalytic chemical vapor deposition (CCVD) technique. The N-MWCNTs were first characterized and then dispersed in high-density polyethylene (HDPE) polymer matrix to form a nanocomposite. The HDPE/N-MWCNT nanocomposite films were prepared by melt mixing and hot pressing; a good dispersion in the matrix and a good N-MWCNT-polymer interfacial adhesion have been verified by scanning electron microscopy (SEM). Raman spectroscopy measurements have been performed on prepared samples to confirm the presence and nature of N-MWNTs in HDPE matrix. The X-ray diffraction (XRD) analysis demonstrated that the crystalline structure of HDPE matrix was not affected by the incorporation of the N-MWNTs.

Low-cost carbon-silicon nanocomposite anodes for lithium ion batteries.

The specific energy of the existing lithium ion battery cells is limited because intercalation electrodes made of activated carbon (AC) materials have limited lithium ion storage capacities. Carbon nanotubes, graphene, and carbon nanofibers are the most sought alternatives to replace AC materials but their synthesis cost makes them highly prohibitive. Silicon has recently emerged as a strong candidate to replace existing graphite anodes due to its inherently large specific capacity and low working potential. However, pure silicon electrodes have shown poor mechanical integrity due to the dramatic expansion of the material during battery operation. This results in high irreversible capacity and short cycle life. We report on the synthesis and use of carbon and hybrid carbon-silicon nanostructures made by a simplified thermo-mechanical milling process to produce low-cost high-energy lithium ion battery anodes. Our work is based on an abundant, cost-effective, and easy-to-launch source of carbon soot having amorphous nature in combination with scrap silicon with crystalline nature. The carbon soot is transformed in situ into graphene and graphitic carbon during mechanical milling leading to superior elastic properties. Micro-Raman mapping shows a well-dispersed microstructure for both carbon and silicon. The fabricated composites are used for battery anodes, and the results are compared with commercial anodes from MTI Corporation. The anodes are integrated in batteries and tested; the results are compared to those seen in commercial batteries. For quick laboratory assessment, all electrochemical cells were fabricated under available environment conditions and they were tested at room temperature. Initial electrochemical analysis results on specific capacity, efficiency, and cyclability in comparison to currently available AC counterpart are promising to advance cost-effective commercial lithium ion battery technology. The electrochemical performance observed for carbon soot material is very interesting given the fact that its production cost is away cheaper than activated carbon. The cost of activated carbon is about $15/kg whereas the cost to manufacture carbon soot as a by-product from large-scale milling of abundant graphite is about $1/kg. Additionally, here, we propose a method that is environmentally friendly with strong potential for industrialization.