Synthesis, Characterization, and Nanomaterials Generated from 6,6'-(((2-Hydroxyethyl)azanediyl)bis(methylene))bis(2,4-di- tert-butylphenol) Modified Group 4 Metal Alkoxides.

The impact on the morphology nanoceramic materials generated from group 4 metal alkoxides ([M(OR)4]) and the same precursors modified by 6,6'-(((2-hydroxyethyl)azanediyl)bis(methylene))bis(2,4-di- tert-butylphenol) (referred to as H3-AM-DBP2 (1)) was explored. The products isolated from the 1:1 stoichiometric reaction of a series of [M(OR)4] where M = Ti, Zr, or Hf; OR = OCH(CH3)2(OPr i); OC(CH3)3(OBu t); OCH2C(CH3)3(ONep) with H3-AM-DBP2 proved, by single crystal X-ray diffraction, to be [(ONep)Ti( k4( O,O',O'',N)-AM-DBP2)] (2), [(OR)M(µ( O)- k3( O',O'',N)-AM-DBP2)]2 [M = Zr: OR = OPr i, 3·tol; OBu t, 4·tol; ONep, 5·tol; M = Hf: OR = OBu t, 6·tol; ONep, 7·tol]. The product from each system led to a tetradentate AM-DBP2 ligand and retention of a parent alkoxide ligand. For the monomeric Ti derivative (2), the metal was solved in a trigonal bipyramidal geometry, whereas for the Zr (3-5) and Hf (6, 7) derivatives a symmetric dinuclear complex was formed where the ethoxide moiety of the AM-DBP2 ligand bridges to the other metal center, generating an octahedral geometry. High quality density functional theory level gas-phase electronic structure calculations on compounds 2-7 using Gaussian 09 were used for meaningful time dependent density functional theory calculations in the interpretation of the UV-vis absorbance spectral data on 2-7. Nanoparticles generated from the solvothermal treatment of the ONep/AM-DBP2 modified compounds (2, 5, 7) in comparison to their parent [M(ONep)4] were larger and had improved regularity and dispersion of the final ceramic nanomaterials.

Titanium hydride nanoparticles and nanoinks for aerosol jet printed electronics.

Conductive inks commonly rely on oxidation-resistant metallic nanoparticles such as gold, silver, copper, and nickel. The criterion of air stability limits the scope of material properties attainable in printed electronic devices. Here we present an alternative approach based on air-stable nanoscale metal hydrides. Conductive patterns based on titanium hydride (TiH2) nanoinks were successfully printed on polyimide under ambient atmosphere and cured using intense pulsed light processing. Nanoparticles of TiH2 were generated by heating TiH2 powder in octylamine followed by wet ball milling, yielding <100 nm platelets. The addition of a suitable polymer dispersant during ball milling yielded stable colloidal dispersions suitable for liquid-phase processing. Aerosol jet printing of the resultant TiH2 nanoinks was demonstrated on glass and polyimide substrates, with a resolution as fine as 20 µm. Following intense pulsed light curing, samples on polyimide were found to exhibit a sintered, porous morphology with an electrical sheet resistance of ∼150 Ω â–¡-1.

Slot-die-coating operability windows for polymer electrolyte membrane fuel cell cathode catalyst layers.

Roll-to-roll (R2R) slot-die coating of polymer electrolyte membrane fuel cell (PEMFC) catalyst layers represents a scalable deposition method for producing 10-20 m2·min-1 of catalyst-coated gas diffusion layers (GDLs). This high-throughput production technique will help lower the cost of PEMFC catalyst layers. The uniformity of the wet layer applied by slot die deposition is affected by process parameters such as substrate speed, vacuum pressure applied at the upstream meniscus, gap between the slot die lips and substrate, ink rheology, and other ink and substrate properties. The set of conditions for producing a defect-free coating with a dilute ink typically requires little to no upstream vacuum pressure, so suitable operating conditions can be found easily through trial and error and operator intuition. However, the higher viscosity of more concentrated inks dramatically shifts the range of settings that result in a homogeneous coating to higher vacuum levels, which are harder to find through hit or miss. A predictive model showing the range of operable conditions decreases material wastage inherent in experimentally searching for suitable parameters. In this study, the defect-free coating parameter window is explored experimentally and theoretically for two concentrations of PEFC cathode inks. Both a full capillary hydrodynamic model and a computationally cheaper viscocapillary model successfully predict the experimentally determined coating window within the experimental and model uncertainty limits for inks with 5.3 wt% and 12.0 wt% solids ink while maintaining the 0.1 mgPt·cm-2Pt areal loading target. This paper demonstrates a viable pathway for meeting the $30/kWnet ultimate cost target of the United States Department of Energy (U.S. DOE) Hydrogen Fuel Cells Technologies Office (HFTO). The concentrated ink lowers the thermal energy and capital expenditure (CapEx) budget of the coating process by decreasing the amount of time, energy, and floorspace required for drying the coating.

The advent of membrane-less zinc-anode aqueous batteries with lithium battery-like voltage.

Zinc (Zn)-anode batteries, although safe and non-flammable, are precluded from promising applications because of their low voltage (<2 V) and poor rechargeability. Here, we report the fabrication of rechargeable membrane-less Zn-anode batteries with high voltage properties (2.5 to 3.4 V) achieved through coupling cathodes and Zn-anodes in gelled concentrated acid and alkaline solutions separated by a gelled buffer interlayer containing the working ions. The concentrated gelled buffer interlayers perform dual functions of regulating the pH of the system and acting as the source and sink of the working ions. With this strategy we show low-cost membrane-less 2.5 to 3.4 V Zn-manganese dioxide (MnO2) batteries capable of cycling 10-100% of 617 mA h g-1-MnO2 and 20-30% of 820 mA h g-1-Zn and demonstrate their application in electric vehicles. This strategy is then applied to other oxide-based cathode systems like Cu2O and V2O5, where voltages of 2 to 3 V are obtained in membrane-less batteries.

Hydroxyl Conducting Hydrogels Enable Low-Maintenance Commercially Sized Rechargeable Zn-MnO2 Batteries for Use in Solar Microgrids.

Zinc (Zn)-manganese dioxide (MnO2) rechargeable batteries have attracted research interest because of high specific theoretical capacity as well as being environmentally friendly, intrinsically safe and low-cost. Liquid electrolytes, such as potassium hydroxide, are historically used in these batteries; however, many failure mechanisms of the Zn-MnO2 battery chemistry result from the use of liquid electrolytes, including the formation of electrochemically inert phases such as hetaerolite (ZnMn2O4) and the promotion of shape change of the Zn electrode. This manuscript reports on the fundamental and commercial results of gel electrolytes for use in rechargeable Zn-MnO2 batteries as an alternative to liquid electrolytes. The manuscript also reports on novel properties of the gelled electrolyte such as limiting the overdischarge of Zn anodes, which is a problem in liquid electrolyte, and finally its use in solar microgrid applications, which is a first in academic literature. Potentiostatic and galvanostatic tests with the optimized gel electrolyte showed higher capacity retention compared to the tests with the liquid electrolyte, suggesting that gel electrolyte helps reduce Mn3+ dissolution and zincate ion migration from the Zn anode, improving reversibility. Cycling tests for commercially sized prismatic cells showed the gel electrolyte had exceptional cycle life, showing 100% capacity retention for >700 cycles at 9.5 Ah and for >300 cycles at 19 Ah, while the 19 Ah prismatic cell with a liquid electrolyte showed discharge capacity degradation at 100th cycle. We also performed overdischarge protection tests, in which a commercialized prismatic cell with the gel electrolyte was discharged to 0 V and achieved stable discharge capacities, while the liquid electrolyte cell showed discharge capacity fade in the first few cycles. Finally, the gel electrolyte batteries were tested under IEC solar off-grid protocol. It was noted that the gelled Zn-MnO2 batteries outperformed the Pb-acid batteries. Additionally, a designed system nameplated at 2 kWh with a 12 V system with 72 prismatic cells was tested with the same protocol, and it has entered its third year of cycling. This suggests that Zn-MnO2 rechargeable batteries with the gel electrolyte will be an ideal candidate for solar microgrid systems and grid storage in general.

Rheological properties of nanopowder alumina coated with adsorbed fatty acids.

The rheological properties of a nanosized alumina powder coated with fatty acid steric stabilizers of varying chain length were investigated. The storage and loss moduli of the complex modulus were measured to characterize the behavior of the flocculated systems. As chain length increased, there was a transition from an elastic response to fluid behavior. However, the fluid system developed elastic characteristics at relatively low volume fractions of 22%. The length of the steric barrier required to produce the fluid dispersion was estimated to be approximately 2 nm and correlates with attractive interactions on the order of the system thermal energy. Moreover, in the flocculated systems, the storage modulus was found to be higher than reported previously in the literature. These higher values were related to the additional attractive forces due to van der Waals attractions between the hydrocarbon tails of the adsorbed fatty acid layers.

In situ characterization of silver nanoparticle synthesis in maltodextrin supramolecular structures.

The use of maltodextrin supramolecular structures (MD SMS) as a reducing agent and colloidal stabilizing agent for the synthesis of Ag nanoparticles (Ag NPs) identified three key points. First, the maltodextrin (MD) solutions are effective in the formation of well-dispersed Ag NPs utilizing alkaline solution conditions, with the resulting Ag NPs ranging in size from 5 to 50 nm diameter. Second, in situ characterization by Raman spectroscopy and small angle X-ray scattering (SAXS) are consistent with initial nucleation of Ag NPs within the MD SMS up to a critical size of ca. 1 nm, followed by a transition to more rapid growth by aggregation and fusion between MD SMS, similar to micelle aggregation reactions. Third, the stabilization of larger Ag NPs by adsorbed MD SMS is similar to hemi-micelle stabilization, and monomodal size distributions are proposed to relate to integer surface coverage of the Ag NPs. Conditions were identified for preparing Ag NPs with monomodal distributions centered at 30-35 nm Ag NPs.

Dispersion properties of an alumina nanopowder using molecular, polyelectrolyte, and steric stabilization.

A commercial alumina nanopowder was characterized and its dispersion was studied using electrostatic, electrosteric, and steric surfactants. Citric acid was used as the electrosteric dispersant, ammonium polymethacrylic acid (Darvan C) as the electrosteric dispersant, and Hypermer KD-1 in alpha-terpineol as a purely steric system. Phase stability in water was examined by X-ray diffraction, and the surface chemistry was characterized by zeta potential and isoelectric points. Rheology measurements were used to study the impact of each dispersant type on maximum solids loading, with the maximum loading being achieved for the polyelectrolyte dispersant. Differences in maximum solids loading are related to the excluded volume of the particle separation distance induced by each stabilizing interaction.

Cation-induced collapse of low-molecular-weight polyacrylic acid in the dispersion of barium titanate.

Observations on the steric layers formed by the adsorption of low-molecular-weight polyacrylic acid (PAA) were taken using the colloidal probe method in an atomic force microscope. The effects of divalent barium ions and of monovalent potassium ions at varying concentrations were observed on the repulsive interaction profiles. High ionic concentrations screened double-layer forces to small distances, whereby the acting forces were reduced to steric interactions. De Gennes scaling theory was used to model the effect of electrolyte on an aqueous barium titanate system, which was stabilized with PAA. The brush model was found to represent the force curves better than the mushroom model. The collapse of PAA layers with increasing salt approximated a grafted polymer brush in monovalent electrolyte, but the addition of barium ions caused markedly less steric collapse. It is suggested that the formation of a Ba(2+)-PAA complex in the adsorbed layer increases its compressibility parameter.

Large area mosaic films of graphene-titania: self-assembly at the liquid-air interface and photo-responsive behavior.

Photo-responsive graphene-titania composite nanofilms were formed via evaporative induced self-assembly at the air-liquid interface from the UV-photo-reduction of titania-graphene oxide colloidal solutions.

Photon control of liquid motion on reversibly photoresponsive surfaces.

The movement of a liquid droplet on a flat surface functionalized with a photochromic azobenzene may be driven by the irradiation of spatially distinct areas of the drop with different UV and visible light fluxes to create a gradient in the surface tension. In order to better understand and control this phenomenon, we have measured the wetting characteristics of these surfaces for a variety of liquids after UV and visible light irradiation. The results are used to approximate the components of the azobenzene surface energy under UV and visible light using the van Oss-Chaudhury-Good equation. These components, in combination with liquid parameters, allow one to estimate the strength of the surface interaction as given by the advancing contact angle for various liquids. The azobenzene monolayers were formed on smooth air-oxidized Si surfaces through 3-aminopropylmethyldiethoxysilane linkages. The experimental advancing and receding contact angles were determined following azobenzene photoisomerization under visible and ultraviolet (UV) light. Reversible light-induced advancing contact-angle changes ranging from 8 to 16 degrees were observed. A large reversible change in contact angle by photoswitching of 12.4 degrees was achieved for water. The millimeter-scale transport of 5 microL droplets of certain liquids was achieved by creating a spatial gradient in visible/UV light across the droplets. A criterion for light-induced motion of droplets is shown to be consistent with the response of a variety of liquids. The type of light-driven fluid movement observed could have applications in microfluidic devices.

Photophysical effects between spirobenzopyran-methyl methacrylate-functionalized colloidal particles.

Colloidal particles were derivatized with end-grafted polymethylmethacrylate polymer brushes containing varying concentrations of spirobenzopyran photochromic molecules. The polymers were grown from initiator-functionalized silica particles by an atom-transfer radical polymerization (ATRP). These core-shell colloids formed stable suspensions in toluene with the spirobenzopyran in its closed, nonpolar form. However, UV-induced photoswitching of the photochrome to its open, polar merocyanine isomer caused rapid aggregation. The nature of this colloidal stability transition was examined with respect to the spirobenzopyran content in the polymeric brush and solvent polarity. Turbidimetry, wettability studies, UV-vis spectroscopy, suspension rheology, SEM, and visual inspection were utilized to characterize the system photoswitchability. It was found that the system exhibiting the greatest transition in toluene was the copolymer brush composed of 20% spirobenzopyran and 80% methyl methacrylate.

Patterned colloid assembly by grafted photochromic polymer layers.

Quartz surfaces and colloidal silica particles were derivatized with a poly(methyl methacrylate) copolymer containing spirobenzopyran (SP) photochromic molecules in the pendant groups at a concentration of 20 mol %. Two-photon near-IR excitation (approximately 780 nm) was then used to create chemically distinct patterns on the modified surfaces through a photochromic process of SP transformation to the zwitterionic merocyanine (MC) isomer. The derivatized colloids were approximately 10 times more likely to adsorb onto the photoswitched, MC regions. Surface coverage and adsorption kinetics have been compared to the mean-field model of irreversible monolayer adsorption.