Efficient charge generation by relaxed charge-transfer states at organic interfaces.

Interfaces between organic electron-donating (D) and electron-accepting (A) materials have the ability to generate charge carriers on illumination. Efficient organic solar cells require a high yield for this process, combined with a minimum of energy losses. Here, we investigate the role of the lowest energy emissive interfacial charge-transfer state (CT1) in the charge generation process. We measure the quantum yield and the electric field dependence of charge generation on excitation of the charge-transfer (CT) state manifold via weakly allowed, low-energy optical transitions. For a wide range of photovoltaic devices based on polymer:fullerene, small-molecule:C60 and polymer:polymer blends, our study reveals that the internal quantum efficiency (IQE) is essentially independent of whether or not D, A or CT states with an energy higher than that of CT1 are excited. The best materials systems show an IQE higher than 90% without the need for excess electronic or vibrational energy.

Ternary bulk heterojunction solar cells: addition of soluble NIR dyes for photocurrent generation beyond 800 nm.

The incorporation of a tert-butyl-functionalized silicon 2,3-naphthalocyanine bis(trihexylsilyloxide) dye molecule as a third component in a ternary blend bulk heterojunction (BHJ) organic solar cell containing P3HT (donor) and PC60BM (acceptor) results in increased NIR absorption. This absorption yields an increase of up to 40% in the short-circuit current and up to 19% in the power conversion efficiency (PCE) in photovoltaic devices. Two-dimensional grazing incidence wide-angle X-ray scattering (2-D GIWAXS) experiments show that compared to the unfunctionalized dye the tert-butyl functionalization enables an increase in the volume fraction of the dye molecule that can be incorporated before the device performance decreases. Quantum efficiency and absorption spectra also indicate that, at dye concentrations above about 8 wt %, there is an approximately 30 nm red shift in the main silicon naphthalocyanine absorption peak, allowing further dye addition to contribute to added photocurrent. This peak shift is not observed in blends with unfunctionalized dye molecules, however. This simple approach of using ternary blends may be generally applicable for use in other unoptimized BHJ systems towards increasing PCEs beyond current levels. Furthermore, this may offer a new approach towards OPVs that absorb NIR photons without having to design, synthesize, and purify complicated donor-acceptor polymers.

Hole transport materials with low glass transition temperatures and high solubility for application in solid-state dye-sensitized solar cells.

We present the synthesis and device characterization of new hole transport materials (HTMs) for application in solid-state dye-sensitized solar cells (ssDSSCs). In addition to possessing electrical properties well suited for ssDSSCs, these new HTMs have low glass transition temperatures, low melting points, and high solubility, which make them promising candidates for increased pore filling into mesoporous titania films. Using standard device fabrication methods and Z907 as the sensitizing dye, power conversion efficiencies (PCE) of 2.94% in 2-µm-thick cells were achieved, rivaling the PCE obtained by control devices using the state-of-the-art HTM spiro-OMeTAD. In 6-µm-thick cells, the device performance is shown to be higher than that obtained using spiro-OMeTAD, making these new HTMs promising for preparing high-efficiency ssDSSCs.

Electronically conductive phospho-olivines as lithium storage electrodes.

Lithium transition metal phosphates have become of great interest as storage cathodes for rechargeable lithium batteries because of their high energy density, low raw materials cost, environmental friendliness and safety. Their key limitation has been extremely low electronic conductivity, until now believed to be intrinsic to this family of compounds. Here we show that controlled cation non-stoichiometry combined with solid-solution doping by metals supervalent to Li+ increases the electronic conductivity of LiFePO4 by a factor of approximately 10(8). The resulting materials show near-theoretical energy density at low charge/discharge rates, and retain significant capacity with little polarization at rates as high as 6,000 mA x g(-1). In a conventional cell design, they may allow development of lithium batteries with the highest power density yet.