Phase-contrast acceleration mapping with synchronized encoding.

PURPOSE: To develop a phase-contrast (PC) -based method for direct and unbiased quantification of the acceleration vector field by synchronization of the spatial and acceleration encoding time points. The proposed method explicitly aims at in-vitro applications, requiring high measurement accuracy, as well as the validation of clinically relevant acceleration-encoded sequences. METHODS: A velocity-encoded sequence with synchronized encoding (SYNC SPI) was modified to allow direct acceleration mapping by replacing the bipolar encoding gradients with tripolar gradient waveforms. The proposed method was validated in two in-vitro flow cases: a rotation and a stenosis phantom. The thereby obtained velocity and acceleration vector fields were quantitatively compared to those acquired with conventional PC methods, as well as to theoretical data. RESULTS: The rotation phantom study revealed a systematic bias of the conventional PC acceleration mapping method that resulted in an average pixel-wise relative angle between the measured and theoretical vector field of (7.8 ± 3.2)°, which was reduced to (-0.4 ± 2.7)° for the proposed SYNC SPI method. Furthermore, flow features in the stenosis phantom were displaced by up to 10 mm in the conventional PC data compared with the acceleration-encoded SYNC SPI data. CONCLUSIONS: This work successfully demonstrates a highly accurate method for direct acceleration mapping. It thus complements the existing velocity-encoded SYNC SPI method to enable the direct and unbiased quantification of both the velocity and acceleration vector field for in vitro studies. Hence, this method can be used for the validation of conventional acceleration-encoded PC methods applicable in-vivo.

Phase-contrast single-point imaging with synchronized encoding: a more reliable technique for in vitro flow quantification.

PURPOSE: The purpose of this study is to provide a standard method for flow velocity measurements with phase-contrast (PC) MRI. This method can be used for in vitro studies that place high demands on measurement accuracy. Clinically relevant PC MRI techniques can be validated using this method before being applied in vivo. METHODS: Many motion-related errors in PC MRI, particularly flow misregistration, depend on the timing of the encoding gradients in the pulse sequence. By synchronizing all encoding gradients and shortening the overall encoding interval, these errors can be significantly reduced. Based on this concept, a single-point PC MRI method is proposed. RESULTS: Flow experiments were conducted in vitro. No considerable errors were found in the velocity data of the proposed method. For comparison, a conventional PC MRI technique showed up to 100% local velocity deviation and up to 35% flow rate deviation in the same experiments. CONCLUSIONS: With the proposed method, the overall measurement accuracy is significantly increased compared to conventional PC MRI techniques. Due to long acquisition times and high specific absorption rates, this method can only be applied in vitro.

Equivalent Scalar Stress Formulation Taking into Account Non-Resolved Turbulent Scales.

PURPOSE: Cardiovascular engineering includes flows with fluid-dynamical stresses as a parameter of interest. Mechanical stresses are high-risk factors for blood damage and can be assessed by computational fluid dynamics. By now, it is not described how to calculate an adequate scalar stress out of turbulent flow regimes when the whole share of turbulence is not resolved by the simulation method and how this impacts the stress calculation. METHODS: We conducted direct numerical simulations (DNS) of test cases (a turbulent channel flow and the FDA nozzle) in order to access all scales of flow movement. After validation of both DNS with literature und experimental data using magnetic resonance imaging, the mechanical stress is calculated as a baseline. Afterwards, same flows are calculated using state-of-the-art turbulence models. The stresses are computed for every result using our definition of an equivalent scalar stress, which includes the influence from respective turbulence model, by using the parameter dissipation. Afterwards, the results are compared with the baseline data. RESULTS: The results show a good agreement regarding the computed stress. Even when no turbulence is resolved by the simulation method, the results agree well with DNS data. When the influence of non-resolved motion is neglected in the stress calculation, it is underpredicted in all cases. CONCLUSION: With the used scalar stress formulation, it is possible to include information about the turbulence of the flow into the mechanical stress calculation even when the used simulation method does not resolve any turbulence.

An unbiased method for PRF-shift temperature measurements in convective heat transfer systems with functional parts made of metal.

The purpose of this study is to provide a PRF-shift method for fluid temperature measurements in convective heat transfer systems, which contain functional parts made of metal. Such measurements are extremely useful to examine and design convective cooling systems for industrial devices. Metals like copper seem inevitable for such applications because no commonly available non-metallic material reaches the same level of thermal conductivity as for example copper. In MRI, electrically conductive parts embedded in the measured sample are known to produce various kinds of errors including errors in the image phase caused by eddy currents. Two methods are compared that can be used to remove the eddy currents induced phase: via the phase difference of two readouts at different echo times and via the sum of the phase of two acquisitions with reverse gradient polarity and same echo time. The latter method, termed Rot-Echo, provides a better measurement efficiency because of higher temperature sensitivity. Also, this technique is able to directly measure the eddy currents induced phase map. After verification in a stationary water experiment, the Rot-Echo method was applied to time-averaged temperature measurements in a Pin Fin heat exchanger, comprised of water flow that is heated by an array of copper pins. The temperature fields acquired in the Pin Fin heat exchanger under stable thermal-hydraulic conditions agreed well with data from temperature sensors. No eddy currents effects were visible in any of the data sets in the vicinity of the copper rods. In conclusion, this study shows that unbiased PRF-shift temperature measurements are feasible in complex flow systems even if metallic material is used for the functional parts.

CFD validation using in-vitro MRI velocity data - Methods for data matching and CFD error quantification.

Predicting blood flow velocities in patient-specific geometries with Computational Fluid Dynamics (CFD) can provide additional data for diagnosis and treatment planning but the solution can be inaccurate. Therefore, it is crucial to understand the simulation errors and calibrate the numerical model. In-vitro velocity-encoded MRI is a versatile tool to validate CFD. The comparison between CFD and in-vitro MRI velocity data, and the analysis of the simulation error are the objectives of this study. A three-step routine is presented to validate medical CFD data. First, a properly scaled model of the patient-specific geometry is fabricated to achieve high relative resolution in the MRI experiment. Second, the measured flow geometry is matched with the CFD data using one of two algorithms, Coherent Point Drift and Iterative Closest Point. The aligned data sets are then interpolated onto a common grid to enable a point-to-point comparison. Third, the global and local deviations between CFD and MRI velocity data are calculated using different algorithms to reliably estimate the simulation error. The routine is successfully tested with a patient-specific model of a cerebral aneurysm. In conclusion, the methods presented here provide a framework for CFD validation using in-vitro MRI velocity data.