Negative Food Effect of Danirixin: Use of PBPK Modelling to Explore the Effect of Formulation and Meal Type on Clinical PK.

PURPOSE: To use physiologically-based pharmacokinetic (PBPK) modelling to explore the food effect of different DNX hydrobromide (HBr) hemihydrate salt tablet formulations using biorelevant dissolution. METHODS: Compendial dissolution using a paddle method and TIM-1 biorelevant dissolution were performed and incorporated into a previously reported PBPK model. A two-part clinical study evaluated tablet formulations in the fasted/fed (high fat) state (Part A), and the impact of food (fasted/normal/high fat) and Proton Pump Inhibitor (PPI) co-administration for a selected formulation; as well as a formulation containing DNX HBr in the monohydrate state (Part B). RESULTS: TIM-1 data showed that the fed state bioaccessibility of DNX was significantly decreased compared to the fasted state with no significant differences between formulations. Dosed with normal/high fat food the selected formulation showed comparable exposure and a modest increase in DNX systemic PK was observed with PPI dependent on meal type. Under fed conditions DNX systemic exposure was comparable for the monohydrate and hemihydrate formulations. The integration of biorelevant TIM-1 data into the PBPK model led to the successful simulation of a DNX negative food effect. CONCLUSIONS: Interactions between DNX and food components are the likely the source of the negative food effect via micellar entrapment, ion pairing and/or meal induced viscosity changes.

Integrating In Vitro Biopharmaceutics into Physiologically Based Biopharmaceutic Model (PBBM) to Predict Food Effect of BCS IV Zwitterionic Drug (GSK3640254).

A strategy followed to integrate in vitro solubility and permeability data into a PBBM model to predict the food effect of a BCS IV zwitterionic drug (GSK3640254) observed in clinical studies is described. The PBBM model was developed, qualified and verified using clinical data of an immediate release (IR)-tablet (10-320 mg) obtained in healthy volunteers under fasted and fed conditions. The solubility of GSK3640254 was a function of its ionization state, the media composition and pH, whereas its permeability determined using MDCK cell lines was enhanced by the presence of mixed micelles. In vitro data alongside PBBM modelling suggested that the positive food effect observed in the clinical studies was attributed to micelle-mediated enhanced solubility and permeability. The biorelevant media containing oleic acid and cholesterol in fasted and fed levels enabled the model to appropriately capture the magnitude of the food effect. Thus, by using Simcyp® v20 software, the PBBM model accurately predicted the results of the food effect and predicted data were within a two-fold error with 70% being within 1.25-fold. The developed model strategy can be effectively adopted to increase the confidence of using PBBM models to predict the food effect of BCS class IV drugs.

In Vitro Biopredictive Methods: A Workshop Summary Report.

This workshop report summarizes the proceedings of Day 1 of a three-day workshop on "Current State and Future Expectations of Translational Modeling Strategies to Support Drug Product Development, Manufacturing Changes and Controls". Physiologically based biopharmaceutics models (PBBM) are tools which enable the drug product quality attributes to be linked to the in vivo performance. These tools rely on key quality inputs in order to provide reliable predictions. After introducing the objectives of the workshop and the expectations from the breakout sessions, Day 1 of the workshop focused on the best practices and challenges in measuring in vitro inputs needed for modeling, such as the drug solubility, the dissolution rate of the drug product, potential precipitation of the drug and drug permeability. This paper reports the podium presentations and summarizes breakout session discussions related to A) the best strategies for determining solubility, supersaturation and critical supersaturation; B) the best strategies for the development of biopredictive (clinically relevant) dissolution methods; C) the challenges associated with describing gastro-intestinal systems parameters such as mucus, liquid volume and motility; and D) the challenges with translating biopharmaceutical measures of drug permeability along the gastrointestinal tract to a meaningful model parameter.

Preparation of glass solutions of three poorly water soluble drugs by spray drying, melt extrusion and ball milling.

The aim of this study was to investigate the influence of the manufacturing process on the physicochemical properties of three poorly water soluble compounds (carbamazepine, dipyridamole, and indomethacin) when processed with a polymer (polyvinylpyrrolidone K30 (PVP)) at a 1:2 drug to polymer ratio. Melt extrusion, spray drying, and ball milling techniques were used to prepare glass solutions. Product homogeneity, dissolution, physical stability, and drug/polymer interactions were investigated. Particular attention was paid to solid phase analysis using XRPD, modulated temperature DSC, optical microscopy, and Raman microscopy and the importance of using a combination of techniques was demonstrated. The latter technique when applied to freshly ball milled samples exhibited the presence of drug and polymer rich areas, indicating that complete glass solution formation had not occurred. The three compounds produced products with differing physical stability with indomethacin proving the most physically stable. These differences in physical stability were attributed to hydrogen bonding of drug and polymer. The manufacturing technique did not influence physical stability, but it did affect dissolution. The dissolution of the spray-dried material was generally poor, compared to melt extruded and ball milled products. This was probably due to rapid dissolution of PVP from the small particles of the spray-dried products.

The influence of thermal and mechanical preparative techniques on the amorphous state of four poorly soluble compounds.

A number of studies in the literature have reported on the use of different preparative techniques to convert crystalline pharmaceutical compounds into the amorphous form. However, very few direct comparisons of different preparative techniques using the same drugs are available. The purpose of this study was to determine the influence of two techniques: quench cooling and ball milling on four structurally diverse pharmaceutical drugs. Dipyridamole, carbamazepine, glibenclamide, and indomethacin were converted to the amorphous form by (a) quench cooling of the drug melt and (b) ball milling. The chemical purity and physical form of the products was determined using diffractometric, spectroscopic, and thermal analytical techniques. Products were analysed immediately post preparation and after storage under different stability conditions. Quench cooling of the melt resulted in amorphous conversion of all four compounds. However with glibenclamide, quench cooling resulted in unacceptable chemical degradation whereas ball milling of glibenclamide resulted in a change in the keto-enol tautomerism at the aryl amide moiety of this drug. Ball milling resulted in predominantly amorphous products for all compounds except carbamazepine. Ball milling of carbamazepine resulted in a polymorphic transition of the starting material to form III. Physical stability studies showed that irrespective of preparative technique and storage conditions all samples showed at least partial reversion to the crystalline state after storage. Quench cooling of drug melts may be of use as a preparative technique however it can result in chemical degradation. Ball milling may also be of use as a preparative technique however its effectiveness is dependent on the unit cell structure of the compound.

The developability classification system: application of biopharmaceutics concepts to formulation development.

A revised classification system for oral drugs was developed using the biopharmaceutics classification system (BCS) as a starting point. The revised system is designed to have a greater focus on drug developability. Intestinal solubility, the compensatory nature of solubility and permeability in the small intestine and an estimate of the particle size needed to overcome dissolution rate limited absorption were all considered in the revised system. The system was then validated by comparison with literature on the in vivo performance of a number of test compounds. Observations on the test compounds were consistent with the revised classification, termed the developability classification system (DCS), showing it to be of greater value in predicting what factors are critical to in vivo performance than the widely used BCS.