Ultracompact Pseudowedge Plasmonic Lasers and Laser Arrays.

Concentrating light at the deep subwavelength scale by utilizing plasmonic effects has been reported in various optoelectronic devices with intriguing phenomena and functionality. Plasmonic waveguides with a planar structure exhibit a two-dimensional degree of freedom for the surface plasmon; the degree of freedom can be further reduced by utilizing metallic nanostructures or nanoparticles for surface plasmon resonance. Reduction leads to different lightwave confinement capabilities, which can be utilized to construct plasmonic nanolaser cavities. However, most theoretical and experimental research efforts have focused on planar surface plasmon polariton (SPP) nanolasers. In this study, we combined nanometallic structures intersecting with ZnO nanowires and realized the first laser emission based on pseudowedge SPP waveguides. Relative to current plasmonic nanolasers, the pseudowedge plasmonic lasers reported in our study exhibit extremely small mode volumes, high group indices, high spontaneous emission factors, and high Purell factors beneficial for the strong interaction between light and matter. Furthermore, we demonstrated that compact plasmonic laser arrays can be constructed, which could benefit integrated plasmonic circuits.

Collective Lasing Behavior of Monolithic GaN-InGaN Core-Shell Nanorod Lattice under Room Temperature.

We demonstrated a monolithic GaN-InGaN core-shell nanorod lattice lasing under room temperature. The threshold pumping density was as low as 140 kW/cm2 with a quality factor as high as 1940. The narrow mode spacing between lasing peaks suggested a strong coupling between adjacent whisper gallery modes (WGM), which was confirmed with the far-field patterns. Excitation area dependent photoluminescence revealed that the long-wavelength lasing modes dominated the collective lasing behavior under a large excitation area. The excitation-area-dependent lasing behavior resulted from the prominent optical coupling among rods. According to the optical mode simulations and truncated-rod experiments, we confirmed that the fine-splitting of lasing peaks originated from the coupled supermodes existing in the periodic nanorod lattices. With wavelength-tunable active materials and a wafer-level scalable processing, patterning optically coupled GaN-InGaN core-shell nanorods is a highly practical approach for building various on-chip optical components including emitters and coupled resonator waveguides in visible and ultraviolet spectral range.

Demonstration of polarization control GaN-based micro-cavity lasers using a rigid high-contrast grating reflector.

We reported on GaN microcavity (MC) lasers combined with one rigid TiO2 high-contrast grating (HCG) structure as the output mirror. The HCG structure was directly fabricated on the GaN structure without an airgap. The entire MC structure comprised a bottom dielectric distributed Bragg reflector; a GaN cavity; and a top HCG reflector, which was designed to yield high reflectance for transverse magnetic (TM)- or transverse electric (TE)-polarized light. The MC device revealed an operation threshold of approximately 0.79 MW/cm2 when pulsed optical pumping was conducted using the HCG structure at room temperature. The laser emission was TM polarized with a degree of polarization of 99.2% and had a small divergence angle of 14° (full width at half maximum). This laser operation demonstration for the GaN-based MC structure employing an HCG exhibited the advantages of HCGs in semiconductor lasers at wavelengths from green to ultraviolet.

Electrically Pumped III-N Microcavity Light Emitters Incorporating an Oxide Confinement Aperture.

In this work, we report on electrically pumped III-N microcavity (MC) light emitters incorporating oxide confinement apertures. The utilized SiO2 aperture can provide a planar ITO design with a higher index contrast (~1) over other previously reported approaches. The fabricated MC light emitter with a 15-µm-aperture shows a turn-on voltage of 3.3 V, which is comparable to conventional light emitting diodes (LEDs), showing a good electrical property of the proposed structure. A uniform light output profile within the emission aperture suggesting the good capability of current spreading and current confinement of ITO and SiO2 aperture, respectively. Although the quality factor (Q) of fabricated MC is not high enough to achieve lasing action (~500), a superlinear emission can still be reached under a high current injection density (2.83 kA/cm2) at 77 K through the exciton-exciton scattering, indicating the high potential of this structure for realizing excitonic vertical-cavity surface-emitting laser (VCSEL) action or even polariton laser after fabrication optimization.

ZnO-Based Microcavities Sculpted by Focus Ion Beam Milling.

We reported an easy fabrication method to realize ZnO-based microcavities with various cavity shapes by focused ion beam (FIB) milling. The optical characteristics of different shaped microcavities have been systematically carried out and analyzed. Through comprehensive studies of cathodoluminescence and photoluminescence spectra, the whispering gallery mode (WGM) was observed in different shaped microcavities. Up further increasing excitation, the lasing action was dominated by these WGMs and matched very well to the simulated results. Our experiment shows that ZnO microcavities with different shapes can be made with high quality by FIB milling for specific applications of microlight sources and optical devices.