RESUMO
Silicon photonic wavefront phase-tilt sensors for wavefront monitoring using surface coupling grating arrays are demonstrated. The first design employs the intrinsic angle dependence of the grating coupling efficiency to determine local wavefront tilt, with a measured sensitivity of 7â dB/°. The second design connects four gratings in an interferometric waveguide circuit to determine incident wavefront phase variation across the sensor area. In this device, one fringe spacing corresponds to 2° wavefront tilt change. These sensor elements sample a wavefront incident on the chip surface without the use of bulk optic elements, fiber arrays, or imaging arrays. Both sensor elements are less than 60â µm across and are potential unit cell sensor elements for large arrays that monitor wavefront shape across an image or pupil plane in adaptive optics systems for free-space optical communications, astronomy, and beam pointing applications.
RESUMO
Recent developments of photonic integrated circuits for the mid-infrared band has opened up a new field of attractive applications for group IV photonics. Grating couplers, formed as diffractive structures on the chip surface, are key components for input and output coupling in integrated photonic platforms. While near-infrared optical fibers exhibit large mode field diameters compared to the wavelength, in the long-wave regime commercially available single-mode optical fibers have mode field diameters of the order of the operating wavelength. Consequently, an efficient fiber-chip surface coupler designed for the long-wave infrared range must radiate the power propagating in the waveguide with a higher radiation strength than a conventional grating coupler in the near-infrared range. In this article, we leverage the short electrical length required for long-wave infrared couplers to design a broadband all-dielectric micro-antenna for a suspended germanium platform at 7.67 µm. The design methodology is inspired by fundamental grating coupler equations, which remain valid even when the micro-antenna has only two or three diffractive elements. A simulated coupling efficiency of ~ 40% is achieved with a 1-dB bandwidth broader than 430 nm, which is almost twice the typical fractional bandwidth of a conventional grating coupler. In addition, the proposed design is markedly tolerant to fiber tilt misalignments of ±10°. This all-dielectric micro-antenna design paves the way for efficient fiber-chip coupling in long-wavelength mid-infrared integrated platforms.
RESUMO
In this work we investigate the implementation of ultra-wideband polarization rotator in the mid-infrared spectral region. A new design method of the rotation section is proposed, yielding a polarization rotator with an extinction ratio of at least 15 dB in a wavelength range of 2 µm. For a spectral range wider than 3.8 µm, an extinction ratio of at least 10 dB is achieved for this design. The device is 1660 µm long and the associated insertion loss is below 1.2 dB on the full operational wavelength range. The influence of geometrical parameters with respect to the design method to obtain such a broadband behavior is discussed. Finally, to increase the tolerance to fabrication errors, a tapered rotator design is proposed. Such a device can support up to ± 100 nm fabrication errors and still guarantees remarkable broadband behavior. To the best of our knowledge, this is the first time an integrated polarization rotator is designed to operate for the wavelength range of 4 to 9 µm with a bandwidth exceeding 2 µm.
RESUMO
In this Letter, we report suspended silicon waveguides operating at a wavelength of 7.67 µm with a propagation loss of 3.1±0.3 dB/cm. To our knowledge, this is the first demonstration of low-loss silicon waveguides at such a long wavelength, with loss comparable to other platforms that use more exotic materials. The suspended Si waveguide core is supported by a sub-wavelength grating that provides lateral optical confinement while also allowing access to the buried oxide layer so that it can be wet etched using hydrofluoric acid. We also demonstrate low-loss waveguide bends and s-bends.
RESUMO
We present several fundamental photonic building blocks based on suspended silicon waveguides supported by a lateral cladding comprising subwavelength grating metamaterial. We discuss the design, fabrication, and characterization of waveguide bends, multimode interference devices and Mach-Zehnder interferometers for the 3715 - 3800 nm wavelength range, demonstrated for the first time in this platform. The waveguide propagation loss of 0.82 dB/cm is reported, some of the lowest loss yet achieved in silicon waveguides for this wavelength range. These results establish a direct path to ultimately extending the operational wavelength range of silicon wire waveguides to the entire transparency window of silicon.
RESUMO
We propose a fiber-chip grating coupler that interleaves the standard full and shallow etch trenches in a 220 nm thick silicon layer to provide a directionality upward exceeding 95%. By adjusting the separation between the two sets of trenches, constructive interference is achieved in the upward direction independent of the bottom oxide thickness and without any bottom reflectors, overlays, or customized etch depths. We implement a transverse subwavelength structure in the first two grating periods to minimize back-reflections. The grating coupler has a calculated coupling efficiency of CE~-1.05 dB with a 1 dB bandwidth of 30 nm and minimum feature size of 100 nm, compatible with deep-UV lithography.
RESUMO
We present a new type of mid-infrared silicon-on-insulator (SOI) waveguide. The waveguide comprises a sub-wavelength lattice of holes acting as lateral cladding while at the same time allowing for the bottom oxide (BOX) removal by etching. The waveguide loss is determined at the wavelength of 3.8 µm for structures before and after being underetched using both vapor phase and liquid hydrofluoric acid (HF). A propagation loss of 3.4 dB/cm was measured for a design with a 300 nm grating period and 150 nm holes after partial removal (560 nm) of BOX by vapor phase HF etching. We also demonstrate an alternative design with 550 nm period and 450 nm holes, which allows a faster and complete removal of the BOX by liquid phase HF etching, yielding the waveguide propagation loss of 3.6 dB/cm.
RESUMO
We propose an ultra-broadband multimode interference (MMI) coupler with a wavelength range exceeding the O, E, S, C, L and U optical communication bands. For the first time, the dispersion property of the MMI section is engineered using a subwavelength grating structure to mitigate wavelength dependence of the device. We present a 2 × 2 MMI design with a bandwidth of 450nm, an almost fivefold enhancement compared to conventional designs, maintaining insertion loss, power imbalance and MMI phase deviation below 1dB, 0.6dB and 3°, respectively. The design is performed using an in-house tool based on the 2D Fourier Eigenmode Expansion Method (F-EEM) and verified with a 3D Finite Difference Time Domain (FDTD) simulator.
Assuntos
Refratometria/instrumentação , Ressonância de Plasmônio de Superfície/instrumentação , Telecomunicações/instrumentação , Desenho Assistido por Computador , Desenho de Equipamento , Análise de Falha de EquipamentoRESUMO
A complete photonic wire molecular biosensor microarray chip architecture and supporting instrumentation is described. Chip layouts with 16 and 128 independent sensors have been fabricated and tested, where each sensor can provide an independent molecular binding curve. Each sensor is 50 µm in diameter, and consists of a millimeter long silicon photonic wire waveguide folded into a spiral ring resonator. An array of 128 sensors occupies a 2 × 2 mm2 area on a 6 × 9 mm2 chip. Microfluidic sample delivery channels are fabricated monolithically on the chip. The size and layout of the sensor array is fully compatible with commercial spotting tools designed to independently functionalize fluorescence based biochips. The sensor chips are interrogated using an instrument that delivers sample fluid to the chip and is capable of acquiring up to 128 optical sensor outputs simultaneously and in real time. Coupling light from the sensor chip is accomplished through arrays of sub-wavelength surface grating couplers, and the signals are collected by a fixed two-dimensional detector array. The chip and instrument are designed so that connection of the fluid delivery system and optical alignment are automated, and can be completed in a few seconds with no active user input. This microarray system is used to demonstrate a multiplexed assay for serotyping E. coli bacteria using serospecific polyclonal antibody probe molecules.
Assuntos
Técnicas Biossensoriais/instrumentação , Escherichia coli/isolamento & purificação , Fotometria/instrumentação , Sorotipagem/instrumentação , Análise Serial de Tecidos/instrumentação , Desenho de Equipamento , Análise de Falha de EquipamentoRESUMO
Directional couplers are extensively used devices in integrated optics, but suffer from limited operational wavelength range. Here we use, for the first time, the dispersive properties of sub-wavelength gratings to achieve a fivefold enhancement in the operation bandwidth of a silicon-on-insulator directional coupler. This approach does not compromise the size or the phase response of the device. The sub-wavelength grating based directional coupler we propose covers a 100 nm bandwidth with an imbalance of ≤ 0.6 dB between its outputs, as supported by full 3D FDTD simulations.
RESUMO
Grating couplers are a promising approach to implement efficient fiber-chip coupling. However, their strong polarization dependence makes dual-polarization operation challenging. In this Letter we propose, for the first time, a polarization-independent grating coupler for thick rib silicon-on-insulator (SOI) waveguides. Coupling efficiency is optimized by designing the grating pitch and duty cycle, without varying the bottom oxide thickness, which significantly simplifies practical implementation. Directivity of the grating coupler is enhanced by a high reflectivity layer under the bottom oxide after the selective removal of the Si substrate. Dual-polarization coupling efficiency of -2.8 dB is shown.
RESUMO
Integrated polarization rotators are known to exhibit stringent fabrication tolerances, which severely handicap their practical application. Here we present a general polarization rotator scheme that enables both the compensation of fabrication errors and wavelength tunability. The scheme is described analytically, and a condition for perfect polarization conversion is established. Simulations of a silicon-on-insulator polarization rotator show polarization extinction ratios in excess of 40 dB even in the presence of large fabrication errors that in a conventional rotator configuration degrade the extinction ratio to below 5 dB. Additionally, wavelength tuning over ±30 nm is shown.
RESUMO
The majority of the applications of ultrashort laser pulses require a control of its spectral bandwidth. In this paper we show the capability of volume phase holographic gratings recorded in photopolymerizable glasses for spectral pulse reshaping of ultrashort laser pulses originated in an Amplified Ti: Sapphire laser system and its second harmonic. Gratings with high laser induce damage threshold (LIDT) allowing wide spectral bandwidth operability satisfy these demands. We have performed LIDT testing in the photopolymerizable glass showing that the sample remains unaltered after more than 10 million pulses with 0,75 TW/cm2 at 1 KHz repetition rate. Furthermore, it has been developed a theoretical model, as an extension of the Kogelnik's theory, providing key gratings design for bandwidth operability. The main features of the diffracted beams are in agreement with the model, showing that non-linear effects are negligible in this material up to the fluence threshold for laser induced damage. The high versatility of the grating design along with the excellent LIDT indicates that this material is a promising candidate for ultrashort laser pulses manipulations.
Assuntos
Vidro/química , Holografia/instrumentação , Lasers , Refratometria/instrumentação , Desenho Assistido por Computador , Desenho de Equipamento , Análise de Falha de Equipamento , Vidro/efeitos da radiação , LuzRESUMO
We demonstrate, by experiment and numerical calculations, temperature-independent subwavelength grating waveguides with a periodic composite core composed of alternating regions of silicon and SU-8 polymer. The polymer has a negative thermo-optic (TO) material coefficient that cancels the large positive TO effect of the silicon. Measurements and Bloch mode calculations were carried out over a range of silicon-polymer duty ratios. The lowest measured TO coefficient at a wavelength of 1550 nm is 1.8×10(-6) K(-1); 2 orders of magnitude smaller than a conventional silicon photonic wire waveguide. Calculations predict the possibility of complete cancellation of the silicon waveguide temperature dependence.
RESUMO
Grating couplers are widely used as an efficient and versatile fiber-chip coupling structure in nanometric silicon wire waveguides. The implementation of efficient grating couplers in micrometric silicon-on-insulator (SOI) rib waveguides is, however, challenging, since the coupler waveguide region is multimode. Here we experimentally demonstrate grating couplers in 1.5 µm-thick SOI rib waveguides with a coupling efficiency of -2.2 dB and a 3 dB bandwidth of 40 nm. An inverse taper is used to adiabatically transform the interconnection waveguide mode to the optimum grating coupler excitation field with negligible higher order Bloch mode excitation. Couplers are fabricated in the same etch step as the waveguides using i-line stepper lithography. The benefits of wafer-scale testing and device characterization without facet preparation are thus attained at no additional cost.
RESUMO
Grating couplers are an efficient means for fiber to chip coupling, as they require no facet preparation and enable wafer scale testing. While grating couplers are commonly used in silicon wire waveguides, their application to micrometric silicon-on-insulator rib waveguides is complicated due to the presence of high-order Bloch modes. We study the Bloch modes behavior and their excitation determined by access waveguide design. The latter is implemented to enable single Bloch mode excitation. The use of a design process based on modal analysis is proposed. A grating coupler is proposed in silicon-on-insulator with 1.5 microm thick silicon layer that achieves a coupling efficiency of 65.6% at 1.55 microm. The structure, including interconnection waveguides, access waveguide and grating can be fabricated using a single lithography step.
RESUMO
A comprehensive investigation of real-time temperature-induced resonance shift cancellation for silicon wire based biosensor arrays is reported for the first time. A reference resonator, protected by either a SU8 or SiO(2) cladding layer, is used to track temperature changes. The temperature dependence of resonators in aqueous solutions, pertinent to biosensing applications, is measured under steady-state conditions and the operating parameters influencing these properties are discussed. Real-time measurements show that the reference resonator resonances reflect the temperature changes without noticeable time delay, enabling effective cancellation of temperature-induced shifts. Binding between complementary IgG protein pairs is monitored over 4 orders of magnitude dynamic range down to a concentration of 20 pM, demonstrating a resolvable mass of 40 attograms. Reactions are measured over time periods as long as 3 hours with high stability, showing a scatter corresponding to a fluid refractive index fluctuation of ± 4 × 10(-6) in the baseline data. Sensor arrays with a SU8 protective cladding are easy to fabricate, while oxide cladding is found to provide superior stability for measurements involving long time scales.
Assuntos
Técnicas Biossensoriais/instrumentação , Técnicas Biossensoriais/métodos , Coloração e Rotulagem , Temperatura , Animais , Eletricidade , Imunoglobulina G/análise , Coelhos , Silício/química , Dióxido de Silício/química , Análise Espectral , Fatores de TempoRESUMO
We demonstrate a fully etched, continuously apodized fiber-to-chip surface grating coupler for the first time (to our knowledge). The device is fabricated in a single-etch step and operates with TM-polarized light, achieving a coupling efficiency of 3.7 dB and a 3 dB bandwidth of 60 nm. A subwavelength microstructure is employed to generate an effective medium engineered to vary the strength of the grating and thereby maximize coupling efficiency, while mitigating backreflections at the same time. Minimum feature size is 100 nm for compatibility with deep-UV 193 nm lithography.
RESUMO
We report a silicon-on-insulator ring resonator biosensor array with one output port, using wavelength division multiplexing as the addressing scheme. With the use of on-chip referencing for environmental drift cancellation, simultaneous monitoring of multiplexed molecular bindings is demonstrated, with a resolution of 0.3 pg/mm(2) (40 ag of total mass) for protein concentrations over 4 orders of magnitude down to 20 pM. Reactions are measured over time periods as long as 3 h with high stability.
Assuntos
Técnicas Biossensoriais/instrumentação , Silício , Animais , Bovinos , Imunoglobulina G/imunologia , Microtecnologia , Soroalbumina Bovina/análise , Soroalbumina Bovina/imunologiaRESUMO
We present an approach to generate paraxial laser beams with arbitrary spatial distribution in the femtosecond time regime. The proposed technique is based upon a pair of volume phase holographic gratings working in parallel arrangement. It exploits the spatial coherence properties of the incoming laser beam in a compact and robust setup that mitigates angular and spatial chirp. The gratings were recorded in a photopolymerizable glass with a high optical damage threshold and a large optical throughput. Setup performance is studied and experimentally demonstrated by generating Laguerre-Gaussian femtosecond pulses.