Spatial Distribution of Brønsted Acid Sites Determines the Mobility of Reactive Cu Ions in the Cu-SSZ-13 Catalyst during the Selective Catalytic Reduction of NOx with NH3.

The formation of dimer-Cu species, which serve as the active sites of the low-temperature selective catalytic reduction of NOx with NH3 (NH3-SCR), relies on the mobility of CuI species in the channels of the Cu-SSZ-13 catalysts. Herein, the key role of framework Brønsted acid sites in the mobility of reactive Cu ions was elucidated via a combination of density functional theory calculations, in situ impedance spectroscopy, and in situ diffuse reflectance ultraviolet-visible spectroscopy. When the number of framework Al sites decreases, the Brønsted acid sites decrease, leading to a systematic increase in the diffusion barrier for [Cu(NH3)2]+ and less formation of highly reactive dimer-Cu species, which inhibits the low-temperature NH3-SCR reactivity and vice versa. When the spatial distribution of Al sites is uneven, the [Cu(NH3)2]+ complexes tend to migrate from an Al-poor cage to an Al-rich cage (e.g., cage with paired Al sites), which effectively accelerates the formation of dimer-Cu species and hence promotes the SCR reaction. These findings unveil the mechanism by which framework Brønsted acid sites influence the intercage diffusion and reactivity of [Cu(NH3)2]+ complexes in Cu-SSZ-13 catalysts and provide new insights for the development of zeolite-based catalysts with excellent SCR activity by regulating the microscopic spatial distribution of framework Brønsted acid sites.

Modulating the Microstructure and Surface Acidity of MnO2 by Doping-Induced Phase Transition for Simultaneous Removal of Toluene and NOx at Low Temperature.

It is a great challenge to remove VOCs and NOx simultaneously from flue gas in nonelectric industries. This study focuses on the construction of Fe-MnO2 catalysts that perform well in the simultaneous removal of toluene and NOx at low temperatures. Utilizing the Fe-induced phase transition of MnO2, Fe-MnO2-F&R catalysts with a composite morphology of nanoflowers and nanorods were successfully prepared that provided an abundant microporous structure to facilitate the diffusion of molecules of different sizes. Through in-depth investigation of the active sites and reaction mechanism, we discovered that Fe-induced phase transition could modulate the surface acidity of Fe-MnO2-F&R. The higher concentration of surface Mn4+ provided numerous Brønsted acid sites, which effectively promoted the activation of toluene to reactive intermediates, such as benzyl alcohol/benzoate/maleic acid. Simultaneously, Fe provided a large number of Lewis acid sites that anchor and activate NH3 species, thereby inhibiting NH3 nonselective oxidation. Furthermore, additional Brønsted acid sites were generated during the simultaneous reaction process, enhancing toluene activation. Consequently, the simultaneous removal of toluene and NOx was achieved through regulation of the physical structure and the concentration of acidic sites. The present work provides new insights into the rational design of bifunctional catalysts for the synergistic control of VOCs and NOx emissions.

Enhancement Effect Induced by the Second Metal to Promote Ozone Catalytic Oxidation of VOCs.

It is a promising research direction to develop catalysts with high stability and ozone utilization for low-temperature ozone catalytic oxidation of VOCs. While bimetallic catalysts exhibit excellent catalytic activity compared with conventional single noble metal catalysts, limited success has been achieved in the influence of the bimetallic effect on the stability and ozone utilization of metal catalysts. Herein, it is necessary to systematically study the enhancement effect in the ozone catalytic reaction induced by the second metal. With a simple continuous impregnation method, a platinum-cerium bimetallic catalyst is prepared. Also highlighted are studies from several aspects of the contribution of the second metal (Ce) to the stability and ozone utilization of the catalysts, including the "electronic effect" and "geometric effect". The synergistic removal rate of toluene and ozone is nearly 100% at 30 °C, and it still shows positive stability after high humidity and a long reaction time. More importantly, the instructive significance, which is the in-depth knowledge of enhanced catalytic mechanism of bimetallic catalysts resulting from a second metal, is provided by this work.

Low-temperature NH3 abatement via selective oxidation over a supported copper catalyst with high Cu+ abundance.

Selective catalytic NH3-to-N2 oxidation (NH3-SCO) is highly promising for abating NH3 emissions slipped from stationary flue gas after-treatment devices. Its practical application, however, is limited by the non-availability of low-cost catalysts with high activity and N2 selectivity. Here, using defect-rich nitrogen-doped carbon nanotubes (NCNT-AW) as the support, we developed a highly active and durable copper-based NH3-SCO catalyst with a high abundance of cuprous (Cu+) sites. The obtained Cu/NCNT-AW catalyst demonstrated outstanding activity with a T50 (i.e. the temperature to reach 50% NH3 conversion) of 174°C in the NH3-SCO reaction, which outperformed not only the Cu catalyst supported on N-free O-functionalized CNTs (OCNTs) or NCNT with less surface defects, but also those most active Cu catalysts in open literature. Reaction kinetics measurements and temperature-programmed surface reactions using NH3 as a probe molecule revealed that the NH3-SCO reaction on Cu/NCNT-AW follows an internal selective catalytic reaction (i-SCR) route involving nitric oxide (NO) as a key intermediate. According to mechanistic investigations by X-ray photoelectron spectroscopy, Raman spectroscopy, and X-ray absorption spectroscopy, the superior NH3-SCO performance of Cu/NCNT-AW originated from a synergy of surface defects and N-dopants. Specifically, surface defects promoted the anchoring of CuO nanoparticles on N-containing sites and, thereby, enabled efficient electron transfer from N to CuO, increasing significantly the fraction of SCR-active Cu+ sites in the catalyst. This study puts forward a new idea for manipulating and utilizing the interplay of defects and N-dopants on carbon surfaces to fabricate Cu+-rich Cu catalysts for efficient abatement of slip NH3 emissions via selective oxidation.

Facile and Scalable Mechanochemical Synthesis of Defective MoS2 with Ru Single Atoms Toward High-Current-Density Hydrogen Evolution.

Designing a facile strategy to prepare catalysts with highly active sites are challenging for large-scale implementation of electrochemical hydrogen production. Herein, a straightforward and eco-friendly method by high-energy mechanochemical ball milling for mass production of atomic Ru dispersive in defective MoS2 catalysts (Ru1 @D-MoS2 ) is developed. It is found that single atomic Ru doping induces the generation of S vacancies, which can break the electronic neutrality around Ru atoms, leading to an asymmetrical distribution of electrons. It is also demonstrated that the Ru1 @D-MoS2 exhibits superb alkaline hydrogen evolution enhancement, possibly attributing to this electronic asymmetry. The overpotential required to deliver a current density of 10 mA cm-2 is as low as 107 mV, which is much lower than that of commercial MoS2 (C-MoS2 , 364 mV). Further density functional theory (DFT) calculations also support that the vacancy-coupled single Ru enables much higher electronic distribution asymmetry degree, which could regulate the adsorption energy of intermediates, favoring the water dissociation and the adsorption/desorption of H*. Besides, the long-term stability test under 500 mA cm-2 further confirms the robust performance of Ru1 @D-MoS2 . Our strategy provides a promising and practical way towards large-scale preparation of advanced HER catalysts for commercial applications.

Cold-Start NOx Mitigation by Passive Adsorption Using Pd-Exchanged Zeolites: From Material Design to Mechanism Understanding and System Integration.

It remains a major challenge to abate efficiently the harmful nitrogen oxides (NOx) in low-temperature diesel exhausts emitted during the cold-start period of engine operation. Passive NOx adsorbers (PNA), which could temporarily capture NOx at low temperatures (below 200 °C) and release the stored NOx at higher temperatures (normally 250-450 °C) to downstream selective catalytic reduction unit for complete abatement, hold promise to mitigate cold-start NOx emissions. In this review, recent advances in material design, mechanism understanding, and system integration are summarized for PNA based on palladium-exchanged zeolites. First, we discuss the choices of parent zeolite, Pd precursor, and synthetic method for the synthesis of Pd-zeolites with atomic Pd dispersions, and review the effect of hydrothermal aging on the properties and PNA performance of Pd-zeolites. Then, we show how different experimental and theoretical methodologies can be integrated to gain mechanistic insights into the nature of Pd active sites, the NOx storage/release chemistry, as well as the interactions between Pd and typical components/poisons in engine exhausts. This review also gathers several novel designs of PNA integration into modern exhaust after-treatment systems for practical application. At the end, we discuss the major challenges, as well as important implications, for the further development and real application of Pd-zeolite-based PNA in cold-start NOx mitigation.

Revealing the Formation and Reactivity of Cage-Confined Cu Pairs in Catalytic NOx Reduction over Cu-SSZ-13 Zeolites by In Situ UV-Vis Spectroscopy and Time-Dependent DFT Calculation.

The low-temperature mechanism of chabazite-type small-pore Cu-SSZ-13 zeolite, a state-of-the-art catalyst for ammonia-assisted selective reduction (NH3-SCR) of toxic NOx pollutants from heavy-duty vehicles, remains a debate and needs to be clarified for further improvement of NH3-SCR performance. In this study, we established experimental protocols to follow the dynamic redox cycling (i.e., CuII ↔ CuI) of Cu sites in Cu-SSZ-13 during low-temperature NH3-SCR catalysis by in situ ultraviolet-visible spectroscopy and in situ infrared spectroscopy. Further integrating the in situ spectroscopic observations with time-dependent density functional theory calculations allows us to identify two cage-confined transient states, namely, the O2-bridged Cu dimers (i.e., µ-η2:η2-peroxodiamino dicopper) and the proximately paired, chemically nonbonded CuI(NH3)2 sites, and to confirm the CuI(NH3)2 pair as a precursor to the O2-bridged Cu dimer. Comparative transient experiments reveal a particularly high reactivity of the CuI(NH3)2 pairs for NO-to-N2 reduction at low temperatures. Our study demonstrates direct experimental evidence for the transient formation and high reactivity of proximately paired CuI sites under zeolite confinement and provides new insights into the monomeric-to-dimeric Cu transformation for completing the Cu redox cycle in low-temperature NH3-SCR catalysis over Cu-SSZ-13.

Economical and Sustainable Synthesis of Small-Pore Chabazite Catalysts for NOx Abatement by Recycling Organic Structure-Directing Agents.

The application of small-pore chabazite-type SSZ-13 zeolites, key materials for the reduction of nitrogen oxides (NOx) in automotive exhausts and the selective conversion of methane, is limited by the use of expensive N,N,N-trimethyl-1-ammonium adamantine hydroxide (TMAdaOH) as an organic structure-directing agent (OSDA) during hydrothermal synthesis. Here, we report an economical and sustainable route for SSZ-13 synthesis by recycling and reusing the OSDA-containing waste liquids. The TMAdaOH concentration in waste liquids, determined by a bromocresol green colorimetric method, was found to be a key factor for SSZ-13 crystallization. The SSZ-13 zeolite synthesized under optimized conditions demonstrates similar physicochemical properties (surface area, porosity, crystallinity, Si/Al ratio, etc.) as that of the conventional synthetic approach. We then used the waste liquid-derived SSZ-13 as the parent zeolite to synthesize Cu ion-exchanged SSZ-13 (i.e., Cu-SSZ-13) for ammonia-mediated selective catalytic reduction of NOx (NH3-SCR) and observed a higher activity as well as better hydrothermal stability than Cu-SSZ-13 by conventional synthesis. In situ infrared and ultraviolet-visible spectroscopy investigations revealed that the superior NH3-SCR performance of waste liquid-derived Cu-SSZ-13 results from a higher density of Cu2+ sites coordinated to paired Al centers on the zeolite framework. The technoeconomic analysis highlights that recycling OSDA-containing waste liquids could reduce the raw material cost of SSZ-13 synthesis by 49.4% (mainly because of the higher utilization efficiency of TMAdaOH) and, meanwhile, the discharging of wastewater by 45.7%.

Copper Site Motion Promotes Catalytic NOx Reduction under Zeolite Confinement.

Ammonia-mediated selective catalytic reduction (NH3-SCR) is currently the key approach to abate nitrogen oxides (NOx) emitted from heavy-duty lean-burn vehicles. The state-of-art NH3-SCR catalysts, namely, copper ion-exchanged chabazite (Cu-CHA) zeolites, perform rather poorly at low temperatures (below 200 °C) and are thus incapable of eliminating effectively NOx emissions under cold-start conditions. Here, we demonstrate a significant promotion of low-temperature NOx reduction by reinforcing the dynamic motion of zeolite-confined Cu sites during NH3-SCR. Combining complex impedance-based in situ spectroscopy (IS) and extended density-functional tight-binding molecular dynamics simulation, we revealed an environment- and temperature-dependent nature of the dynamic Cu motion within the zeolite lattice. Further coupling in situ IS with infrared spectroscopy allows us to unravel the critical role of monovalent Cu in the overall Cu mobility at a molecular level. Based on these mechanistic understandings, we elicit a boost of NOx reduction below 200 °C by reinforcing the dynamic Cu motion in various Cu-zeolites (Cu-CHA, Cu-ZSM-5, Cu-Beta, etc.) via facile postsynthesis treatments, either in a reductive mixture at low temperatures (below 250 °C) or in a nonoxidative atmosphere at high temperatures (above 450 °C).

Application of logistic regression, support vector machine and random forest on the effects of titanium dioxide nanoparticles using macroalgae in treatment of certain risk factors associated with kidney injuries.

The use of titanium dioxide (TiO2) nanoparticles in many biological and technical domains is on the rise. There hasn't been much research on the toxicity of titanium dioxide nanoparticles in biological systems, despite their ubiquitous usage. In the current investigation, samples were exposed to various dosages of TiO2 nanoparticles for 4 days, 1 month, and 2 months following treatment. ICP-AES was used to dose TiO2 into the tissues, and the results showed that the kidney had a significant TiO2 buildup. On the other hand, apoptosis of renal tubular cells is one of the most frequent cellular processes contributing to kidney disease (KD). Nevertheless, the impact of macroalgal seaweed extract on KD remains undetermined. In this work, machine learning (ML) approaches have been applied to develop prediction algorithms for acute kidney injury (AKI) by use of titanium dioxide and macroalgae in hospitalized patients. Fifty patients with (AKI) and 50 patients (non-AKI group) have been admitted and considered. Regarding demographic data, and laboratory test data as input parameters, support vector machine (SVM), and random forest (RF) are utilized to build models of AKI prediction and compared to the predictive performance of logistic regression (LR). Due to its strong antioxidant and anti-inflammatory powers, the current research ruled out the potential of using G. oblongata red macro algae as a source for a variety of products for medicinal uses. Despite a high and fast processing of algorithms, logistic regression showed lower overfitting in comparison to SVM, and Random Forest. The dataset is subjected to algorithms, and the categorization of potential risk variables yields the best results. AKI samples showed significant organ defects than non-AKI ones. Multivariate LR indicated that lymphocyte, and myoglobin (MB) ≥ 1000 ng/ml were independent risk parameters for AKI samples. Also, GCS score (95% CI 1.4-8.3 P = 0.014) were the risk parameters for 60-day mortality in samples with AKI. Also, 90-day mortality in AKI patients was significantly high (P < 0.0001). In compared to the control group, there were no appreciable changes in the kidney/body weight ratio or body weight increases. Total thiol levels in kidney homogenate significantly decreased, and histopathological analysis confirmed these biochemical alterations. According to the results, oral TiO2 NP treatment may cause kidney damage in experimental samples.

Ammonia Abatement via Selective Oxidation over Electron-Deficient Copper Catalysts.

Selective catalytic ammonia-to-dinitrogen oxidation (NH3-SCO) is highly promising for the abatement of NH3 emissions from flue gas purification devices. However, there is still a lack of high-performance and cost-effective NH3-SCO catalysts for real applications. Here, highly dispersed, electron-deficient Cu-based catalysts were fabricated using nitrogen-doped carbon nanotubes (NCNT) as support. In NH3-SCO catalysis, the Cu/NCNT outperformed Cu supported on N-free CNTs (Cu/OCNT) and on other types of supports (i.e., activated carbon, Al2O3, and zeolite) in terms of activity, selectivity to the desired product N2, and H2O resistance. Besides, Cu/NCNT demonstrated a better structural stability against oxidation and a higher NH3 storage capacity (in the presence of H2O vapor) than Cu/OCNT. Quasi in situ X-ray photoelectron spectroscopy revealed that the surface N species facilitated electron transfer from Cu to the NCNT support, resulting in electron-deficient Cu catalysts with superior redox properties, which are essential for NH3-SCO catalysis. By temperature-programmed surface reaction studies and systematic kinetic measurements, we unveiled that the NH3-SCO reaction over Cu/NCNT proceeded via the internal selective catalytic reaction (i-SCR) route; i.e., NH3 was oxidized first to NO, which then reacted with NH3 and O2 to form N2 and H2O. This study paves a new route for the design of highly active, H2O-tolerant, and low-cost Cu catalysts for the abatement of slip NH3 from stationary emissions via selective oxidation to N2.

Inhibition Effect of Phosphorus Poisoning on the Dynamics and Redox of Cu Active Sites in a Cu-SSZ-13 NH3-SCR Catalyst for NOx Reduction.

Phosphorus (P) stemming from biodiesel and/or lubricant oil additives is unavoidable in real diesel exhausts and deactivates gradually the Cu-SSZ-13 zeolite catalyst for ammonia-assisted selective catalytic NOx reduction (NH3-SCR). Here, the deactivation mechanism of Cu-SSZ-13 by P-poisoning was investigated by ex situ examination of the structural changes and by in situ probing the dynamics and redox of Cu active sites via a combination of impedance spectroscopy, diffuse reflection infrared Fourier transform spectroscopy, and ultraviolet-visible spectroscopy. We unveiled that strong interactions between Cu and P led to not only a loss of Cu active sites for catalytic turnovers but also a restricted dynamic motion of Cu species during low-temperature NH3-SCR catalysis. Furthermore, the CuII ↔ CuI redox cycling of Cu sites, especially the CuI → CuII reoxidation half-cycle, was significantly inhibited, which can be attributed to the restricted Cu motion by P-poisoning disabling the formation of key dimeric Cu intermediates. As a result, the NH3-SCR activity at low temperatures (200 °C and below) decreased slightly for the mildly poisoned Cu-SSZ-13 and considerably for the severely poisoned Cu-SSZ-13.

Macroscopic Hexagonal Co3O4 Tubes Derived from Controllable Two-Dimensional Metal-Organic Layer Single Crystals: Formation Mechanism and Catalytic Activity.

Macroscopic Co3O4 hexagonal tubes were successfully synthesized using hollow two-dimensional (2D) MOL (metal-organic layer) single crystals as sacrificial templates. The hollow 2D MOL single crystals were prepared under hydrothermal conditions with acetonitrile (MeCN) as an interference agent. The formation of hollow-structured 2D MOL single crystals was tracked by time-dependent experiments, and two simultaneous paths-namely, the crystal-to-crystal transformation in solution and the dissolution + migration (toward the external surface) of inner crystallites-were identified as playing a key role in the formation of the unique hollow structure. The calculated change in Gibbs free energy (ΔG = -1.18 eV) indicated that the crystal-to-crystal transformation was spontaneous at 393 K. Further addition of MeCN as an interference agent eventually leads to the formation of macroscopic hexagonal tubes. Among all of the as-synthesized Co3O4, Co-MeCN-O with a hexagonal tube morphology exhibited the best catalytic performance in toluene oxidation, it achieved a toluene conversion of 90% (T90) at ∼227 °C (a space velocity of 60 000 mL g-1 h-1) and the activity energy (Ea) is 69.5 kJ mol-1. A series of characterizations were performed to investigate the structure-activity correlation. It was found that there are more structure defects, more adsorbed surface oxygen species, more surface Co3+ species, and higher reducibility at low temperatures on the Co-MeCN-O than on other Co3O4 samples; these factors are responsible for its excellent catalytic performance. The in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) characterization showed that, when there is no oxygen in the atmosphere, the lattice oxygen may be involved in the activation of toluene, and the gas-phase oxygen replenished by the oxygen vacancies was essential for the total oxidation of toluene on the surface of the Co-MeCN-O catalysts, it also proves the importance of oxygen vacancies. Moreover, for the Co-MeCN-O catalysts, no obvious decrease in catalytic performance was observed after 120 h at 220 °C and it is still stable after cycling tests, which indicates that it exhibits excellent stability for toluene oxidation. This study sheds lights on the controllable synthesis of macroporous-microporous materials in single-crystalline form without an external template, and, thus, it may serve as a reference for future design and synthesis of hollow porous materials with outstanding catalytic performance.

Interferon-induced RIP1/RIP3-mediated necrosis requires PKR and is licensed by FADD and caspases.

Interferons (IFNs) are cytokines with powerful immunomodulatory and antiviral properties, but less is known about how they induce cell death. Here, we show that both type I (α/ß) and type II (γ) IFNs induce precipitous receptor-interacting protein (RIP)1/RIP3 kinase-mediated necrosis when the adaptor protein Fas-associated death domain (FADD) is lost or disabled by phosphorylation, or when caspases (e.g., caspase 8) are inactivated. IFN-induced necrosis proceeds via progressive assembly of a RIP1-RIP3 "necrosome" complex that requires Jak1/STAT1-dependent transcription, but does not need the kinase activity of RIP1. Instead, IFNs transcriptionally activate the RNA-responsive protein kinase PKR, which then interacts with RIP1 to initiate necrosome formation and trigger necrosis. Although IFNs are powerful activators of necrosis when FADD is absent, these cytokines are likely not the dominant inducers of RIP kinase-driven embryonic lethality in FADD-deficient mice. We also identify phosphorylation on serine 191 as a mechanism that disables FADD and collaborates with caspase inactivation to allow IFN-activated necrosis. Collectively, these findings outline a mechanism of IFN-induced RIP kinase-dependent necrotic cell death and identify FADD and caspases as negative regulators of this process.

Correlating the Integral Sensing Properties of Zeolites with Molecular Processes by Combining Broadband Impedance and DRIFT Spectroscopy--A New Approach for Bridging the Scales.

Zeolites have been found to be promising sensor materials for a variety of gas molecules such as NH3, NOx, hydrocarbons, etc. The sensing effect results from the interaction of the adsorbed gas molecules with mobile cations, which are non-covalently bound to the zeolite lattice. The mobility of the cations can be accessed by electrical low-frequency (LF; mHz to MHz) and high-frequency (HF; GHz) impedance measurements. Recent developments allow in situ monitoring of catalytic reactions on proton-conducting zeolites used as catalysts. The combination of such in situ impedance measurements with diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS), which was applied to monitor the selective catalytic reduction of nitrogen oxides (DeNOx-SCR), not only improves our understanding of the sensing properties of zeolite catalysts from integral electric signal to molecular processes, but also bridges the length scales being studied, from centimeters to nanometers. In this work, recent developments of zeolite-based, impedimetric sensors for automotive exhaust gases, in particular NH3, are summarized. The electrical response to NH3 obtained from LF impedance measurements will be compared with that from HF impedance measurements, and correlated with the infrared spectroscopic characteristics obtained from the DRIFTS studies of molecules involved in the catalytic conversion. The future perspectives, which arise from the combination of these methods, will be discussed.

Mucosal vaccines for viral diseases: Status and prospects.

Virus-associated infectious diseases are highly detrimental to human health and animal husbandry. Among all countermeasures against infectious diseases, prophylactic vaccines, which developed through traditional or novel approaches, offer potential benefits. More recently, mucosal vaccines attract attention for their extraordinary characteristics compared to conventional parenteral vaccines, particularly for mucosal-related pathogens. Representatively, coronavirus disease 2019 (COVID-19), a respiratory disease caused by severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), further accelerated the research and development efforts for mucosal vaccines by thoroughly investigating existing strategies or involving novel techniques. While several vaccine candidates achieved positive progresses, thus far, part of the current COVID-19 mucosal vaccines have shown poor performance, which underline the need for next-generation mucosal vaccines and corresponding platforms. In this review, we summarized the typical mucosal vaccines approved for humans or animals and sought to elucidate the underlying mechanisms of these successful cases. In addition, mucosal vaccines against COVID-19 that are in human clinical trials were reviewed in detail since this public health event mobilized all advanced technologies for possible solutions. Finally, the gaps in developing mucosal vaccines, potential solutions and prospects were discussed. Overall, rational application of mucosal vaccines would facilitate the establishing of mucosal immunity and block the transmission of viral diseases.

Investigation on chain segment motions of various starch molecules under different glycerol-water system.

The molecular motion of starch at different glycerol concentrations (0, 20, 50, and 80 %) was investigated using Electron Paramagnetic Resonance (EPR) spectroscopy. Fourier-transform infrared (FTIR) spectroscopy and 1H nuclear magnetic resonance (1H NMR) spectroscopy confirmed that hydroxyl groups at the C2 and C3 positions of glucose units in corn starch (CS), waxy corn starch (WCS), and high amylose corn starch (HCS) were labeled with 4-amino-TEMPO. The crystallinities of CS, WCS, and HCS after spin-labeling decreased from 30.68 % to 3.21 %, 39.36 % to 1.65 %, and 28.54 % to 8.08 %, respectively. The pseudoplastic fluid properties of the spin-labeled starch remained shear-thin at different glycerol concentrations. EPR revealed the fast- and slow-motion components of the spin-labeled starch molecules dispersed in water. At a glycerol concentration of 20 %, the slow-motion component disappeared, indicating a faster rotational motion of the starch chain segments. As the glycerol concentration increased to 50 and 80 %, the rotational motion slowed because of high viscosity. In particular, the mobility of the spin-labeled WCS chains increased owing to easier access of glycerol and water to the branched structure. This study directly observed the dynamics of the molecular behavior of starch in glycerol-water systems.

Process-specified emission factors and characteristics of VOCs from the auto-repair painting industry.

Daily use of passenger vehicles leads to considerable emission of volatile organic compounds (VOCs), which are key precursors to the ground-level ozone pollution. While evaporative and tailpipe emission of VOCs from the passenger vehicles can be eliminated largely, or even completely, by electrification, VOCs emission from the use of coatings in auto-repair is unavoidable and has long been ignored. Here, we present for the first time, to the best of our knowledge, a comprehensive investigation on the emission factors and process-specified characteristics of VOCs from auto-repair painting, based on field measurements over 15 representative auto-repair workshops in the Pearl-River-Delta area, China. Replacement of solvent-borne coatings with water-borne counterparts, which was only achieved partially in the Basecoat step but not in the Putty, Primer and Clearcoat steps, could reduce the per automobile VOCs emission from 756.5 to 489.6 g and the per automobile ozone formation potential (OFP) from 2776.5 to 1666.4 g. Implementation of exhaust after-treatment led to a further reduction of the per automobile VOCs emission to 340.9 g, which is still ca. 42% higher than that from the state-of-art painting processes for the manufacture of passenger vehicles. According to the analysis of VOCs compositions, the Putty process was dominated by the emission of styrene, while Primer, Basecoat (solvent-borne) and Clearcoat steps were all characterized by the emission of n-butyl acetate and xylenes. By contrast, water-borne Basecoat step showed a prominent emission of n-amyl alcohol. Notably, for the full painting process to repair an automobile, n-butyl acetate emerged as the most abundant species in the VOCs emission, whereas xylenes contributed most significantly to the OFP. Scenario analysis suggested that reducing VOCs contents in the coatings, as well as improving the after-treatment efficiency, were highly potential solutions for effective reduction of VOCs emission from auto-repair. Our study contributes to an update of industrial inventories of VOCs emission, and may provide valuable insights for reducing VOCs emission and OFPs from the auto-repair industry.

AflaILVB/G/I and AflaILVD are involved in mycelial production, aflatoxin biosynthesis, and fungal virulence in Aspergillus flavus.

Aflatoxins (AFs) are produced by fungi such as Aspergillus flavus and A. parasiticus and are one of the most toxic mycotoxins found in agricultural products and food. Aflatoxin contamination, which requires the control of A. flavus, remains problematic because of the lack of effective strategies and the exploration of new compounds that can inhibit A. flavus growth and mycotoxin production is urgently required to alleviate potential deleterious effects. Acetohydroxy acid synthase (AHAS) and dihydroxy acid dehydratase are important enzymes in the biosynthetic pathways of branched-chain amino acids (BCAAs), including isoleucine, leucine, and valine. Enzymes involved in BCAA biosynthesis are present in bacteria, plants, and fungi, but not in mammals, and are therefore, attractive targets for antimicrobial and herbicide development. In this study, we characterized AflaILVB/G/I and AflaILVD, which encode the catalytic and regulatory subunits of AHAS and dihydroxy acid dehydratase, from the pathogenic fungus Aspergillus flavus. The AflaILVB/G/I and AflaILVD deletion mutant grew slower and produced smaller colonies than the wild-type strain when grown on glucose minimal medium, potato dextrose agar, and yeast extract medium for three days at 28°C, and disruption of AflaILVB/G/I caused a significant reduction in conidia production when grown on all kinds of media. Cellular stress assays determined that all strains were sensitive to H2O2. Importantly, the pathogenicity and aflatoxin production were affected when AflaILVB/G/I and AflaILVD were knocked out, particularly AflaILVB/G/I. A series of genes that encoded enzymes involved in aflatoxin synthesis were downregulated, meaning that the knockout of AflaILVB/G/I influenced aflatoxin synthesis in A. flavus strain WT. Collectively, our results demonstrate the potential value of antifungals targeting AflaILVB/G/I in A. flavus.

Efficient Atomically Dispersed Co/N-C Catalysts for Formic Acid Dehydrogenation and Transfer Hydrodeoxygenation of Vanillin.

Atomically dispersed catalysts have gained considerable attention due to their unique properties and high efficiency in various catalytic reactions. Herein, a series of Co/N-doped carbon (N-C) catalysts was prepared using a metal-lignin coordination strategy and employed in formic acid dehydrogenation (FAD) and hydrodeoxygenation (HDO) of vanillin. The atomically dispersed Co/N-C catalysts showed outstanding activity, acid resistance, and long-term stability in FAD. The improved activity and stability may be attributed to the high dispersion of Co species, increased surface area, and strong Co-N interactions. XPS and XAS characterization revealed the formation of Co-N3 centers, which are assumed to be the active sites. In addition, DFT calculations demonstrated that the adsorption of formic acid on single-atom Co was stronger than that on Co13 clusters, which may explain the high catalytic activity. The Co/N-C catalyst also showed promising performance in the transfer HDO of vanillin with formic acid, without any external additional molecular H2.