RESUMO
Atomically thin graphene with a high-density of precise subnanometer pores represents the ideal membrane for ionic and molecular separations. However, a single large-nanopore can severely compromise membrane performance and differential etching between pre-existing defects/grain boundaries in graphene and pristine regions presents fundamental limitations. Here, we show for the first time that size-selective interfacial polymerization after high-density nanopore formation in graphene not only seals larger defects (>0.5 nm) and macroscopic tears but also successfully preserves the smaller subnanometer pores. Low-temperature growth followed by mild UV/ozone oxidation allows for facile and scalable formation of high-density (4-5.5 × 1012 cm-2) useful subnanometer pores in the graphene lattice. We demonstrate scalable synthesis of fully functional centimeter-scale nanoporous atomically thin membranes (NATMs) with water (â¼0.28 nm) permeance â¼23× higher than commercially available membranes and excellent rejection to salt ions (â¼0.66 nm, >97% rejection) as well as small organic molecules (â¼0.7-1.5 nm, â¼100% rejection) under forward osmosis.
RESUMO
Memristor, which had been predicted a long time ago (Chua, L. O. IEEE Trans. Circuit Theory 1971, 18, 507), was recently invented (Strukov, D. B.; et al. Nature 2008, 453, 80). The introduction of a memristor is expected to open a new era for nonvolatile memory storage, neuromorphic computing, digital logic, and analog circuit. Furthermore, several breakthroughs were made for memristive phenomena and transistors with single-layer MoS2 (Sangwan, V. K.; et al. Nat. Nanotechnol. 2015, 10, 403. van der Zande, A. M.; et al. Nat. Mater. 2013, 12, 554. Liu, H.; et al. ACS Nano 2014, 8, 1031. Bessonov, A. A.; et al. Nat. Mater. 2015, 14, 199. Yuan, J.; et al. Nat. Nanotechnol. 2015, 10, 389). Herein, we demonstrate that 2H phase of bulk MoS2 possessed an ohmic feature, whereas 1T phase of exfoliated MoS2 nanosheets exhibited a unique memristive behavior due to voltage-dependent resistance change. Furthermore, an ideal odd-symmetric memristor with odd-symmetric I-V characteristics was successfully fabricated by the 1T phase MoS2 nanosheets via combining two asymmetric switches antiserially.
RESUMO
Angstrom-scale pores introduced into atomically thin 2D materials offer transformative advances for proton exchange membranes in several energy applications. Here, we show that facile kinetic control of scalable chemical vapor deposition (CVD) can allow for direct formation of angstrom-scale proton-selective pores in monolayer graphene with significant hindrance to even small, hydrated ions (K+ diameter â¼6.6 Å) and gas molecules (H2 kinetic diameter â¼2.9 Å). We demonstrate centimeter-scale Nafion|Graphene|Nafion membranes with proton conductance â¼3.3-3.8 S cm-2 (graphene â¼12.7-24.6 S cm-2) and H+/K+ selectivity â¼6.2-44.2 with liquid electrolytes. The same membranes show proton conductance â¼4.6-4.8 S cm-2 (graphene â¼39.9-57.5 S cm-2) and extremely low H2 crossover â¼1.7 × 10-1 - 2.2 × 10-1 mA cm-2 (â¼0.4 V, â¼25 °C) with H2 gas feed. We rationalize our findings via a resistance-based transport model and introduce a stacking approach that leverages combinatorial effects of interdefect distance and interlayer transport to allow for Nafion|Graphene|Graphene|Nafion membranes with H+/K+ selectivity â¼86.1 (at 1 M) and record low H2 crossover current density â¼2.5 × 10-2 mA cm-2, up to â¼90% lower than state-of-the-art ionomer Nafion membranes â¼2.7 × 10-1 mA cm-2 under identical conditions, while still maintaining proton conductance â¼4.2 S cm-2 (graphene stack â¼20.8 S cm-2) comparable to that for Nafion of â¼5.2 S cm-2. Our experimental insights enable functional atomically thin high flux proton exchange membranes with minimal crossover.
RESUMO
Filtering nanoparticulate aerosols from air streams is important for a wide range of personal protection equipment (PPE), including masks used for medical research, healthcare, law enforcement, first responders, and military applications. Conventional PPEs capable of filtering nanoparticles <300 nm are typically bulky and sacrifice breathability to maximize protection from exposure to harmful nanoparticulate aerosols including viruses â¼20-300 nm from air streams. Here, we show that nanopores introduced into centimeter-scale monolayer graphene supported on polycarbonate track-etched supports via a facile oxygen plasma etch can allow for filtration of aerosolized SiO2 nanoparticles of â¼5-20 nm from air steams while maintaining air permeance of â¼2.28-7.1 × 10-5 mol m-2 s-1 Pa-1. Furthermore, a systematic increase in oxygen plasma etch time allows for a tunable size-selective filtration of aerosolized nanoparticles. We demonstrate a new route to realize ultra-compact, lightweight, and conformal form-factor filters capable of blocking sub-20 nm aerosolized nanoparticles with particular relevance for biological/viral threat mitigation.
RESUMO
The transport of water through nanoscale capillaries/pores plays a prominent role in biology, ionic/molecular separations, water treatment and protective applications. However, the mechanisms of water and vapor transport through nanoscale confinements remain to be fully understood. Angstrom-scale pores (~2.8-6.6 Å) introduced into the atomically thin graphene lattice represent ideal model systems to probe water transport at the molecular-length scale with short pores (aspect ratio ~1-1.9) i.e., pore diameters approach the pore length (~3.4 Å) at the theoretical limit of material thickness. Here, we report on orders of magnitude differences (~80×) between transport of water vapor (~44.2-52.4 g m-2 day-1 Pa-1) and liquid water (0.6-2 g m-2 day-1 Pa-1) through nanopores (~2.8-6.6 Å in diameter) in monolayer graphene and rationalize this difference via a flow resistance model in which liquid water permeation occurs near the continuum regime whereas water vapor transport occurs in the free molecular flow regime. We demonstrate centimeter-scale atomically thin graphene membranes with up to an order of magnitude higher water vapor transport rate (~5.4-6.1 × 104 g m-2 day-1) than most commercially available ultra-breathable protective materials while effectively blocking even sub-nanometer (>0.66 nm) model ions/molecules.
Assuntos
Grafite , Nanoporos , Vapor , Gases , Membranas , ÍonsRESUMO
Scalable graphene synthesis and facile large-area membrane fabrication are imperative to advance nanoporous atomically thin membranes (NATMs) for molecular separations. Although chemical vapor deposition (CVD) allows for roll-to-roll high-quality monolayer graphene synthesis, facile transfer with atomically clean interfaces to porous supports for large-area NATM fabrication remains extremely challenging. Sacrificial polymer scaffolds commonly used for graphene transfer typically leave polymer residues detrimental to membrane performance and transfers without polymer scaffolds suffer from low yield resulting in high non-selective leakage through NATMs. Here, we systematically study the factors influencing graphene NATM fabrication and report on a novel roll-to-roll manufacturing compatible isopropanol-assisted hot lamination (IHL) process that enables scalable, facile and clean transfer of CVD graphene on to polycarbonate track etched (PCTE) supports with coverage ≥99.2%, while preserving support integrity/porosity. We demonstrate fully functional centimeter-scale graphene NATMs that show record high permeances (â¼2-3 orders of magnitude higher) and better selectivity than commercially available state-of-the-art polymeric dialysis membranes, specifically in the 0-1000 Da range. Our work highlights a scalable approach to fabricate graphene NATMs for practical applications and is fully compatible with roll-to-roll manufacturing processes.
RESUMO
Zn(2-methylimidazole)2 (ZIF-8), as one of the most important metal-organic framework (MOF) molecules, is a promising candidate for drug delivery due to its low-density structure, high surface area, and tunable frameworks. However, ZIF-8 exhibits a high cytotoxicity associated with its external hydrophobic surface, which significantly restricts its application in drug delivery and other biomedical applications. Commonly used chemical functionalization methods would convert the hydrophobic surface of ZIF-8 to hydrophilic, but the generated functional groups on its internal surface may reduce its pore sizes or even block its pores. Herein, a surface defection strategy was applied on the external surface of ZIF-8 to enhance its hydrophilicity without reducing or blocking the internal pores. In this approach, mechanical ball-milling was used to incur defects on the external surface of ZIF-8, leading to unsaturated Zn-sites and N-sites which subsequently bound H2O molecules in an aqueous environment. Furthermore, hydroxyurea delivery and cell cytotoxicity of ZIF-8 with and without the external surface treatment were evaluated. It was found that 5-min ball milling changed the hydrophobic-hydrophilic balance of ZIF-8, resulting in significantly higher cell viability without compromising its hydroxyurea loading and release capacity. Such a simple mechanical ball-milling followed by water-treatment provides a general technique for surface-modification of other MOF molecules, which will undoubtedly magnify their biomedical applications.