Thermistors coated with molecularly imprinted nanoparticles for the electrical detection of peptides and proteins.

In this communication, molecularly imprinted nanoparticles (nanoMIPs) that are produced by solid-phase synthesis are functionalised onto thermistors via dip-coating. These thermistors are soldered onto a printed-circuit board to facilitate electrical detection. Subsequently, these are inserted into a home-made thermal device that can measure the selective binding of biomolecules to the nanoMIP layer via monitoring the thermal resistance (Rth) at the solid-liquid interface. This thermal analysis technique, referred to as the Heat-Transfer Method, has previously been used for detection of proteins with MIP-based binders. While offering the advantages of low-cost and label free analysis, this method is limited by the high noise on the feedback loop and not being commercially available. These disadvantages can be overcome by the use of thermistors, which offer superior temperature sensitivity compared to thermocouples, and its electrical read-out can be easily integrated into portable devices. To our knowledge, this is the first report where MIPs are directly integrated onto thermistors for detection purposes. Measurements were conducted with an epitope of epidermal growth factor receptor (EGFR) and trypsin, where the electrical resistance was correlated to the biomolecule concentration. For both EGFR and trypsin, an enhanced signal to noise ratio for the electrical measurements was observed compared to previous analysis that was based on thermal resistance. The sensitivity of the sensors in buffered solution was in the nanomolar range, which is compatible with physiologically relevant concentrations. Upon exposure of the nanoMIP for EGFR towards pepsin no significant change in the resistance was yielded, establishing the selectivity of the developed sensor platform. Besides the enhanced sensitivity, the use of thermistors will enable miniaturisation of the device and has potential for in vivo measurements since specified electrochemical measurements are compatible with human use. To highlight the versatility of the nanoMIPs, this work should be extended to a set of biomolecules with various structures, with the possibility of extending this to an array format.

Evaluating the potential of thermal read-out techniques combined with molecularly imprinted polymers for the sensing of low-weight organic molecules.

In recent years, there has been a tremendous increase in the papers published on synthetic recognition elements. Molecularly imprinted polymers (MIPs), also referred to as "man-made mimics" of antibodies, are able to rebind their template molecules with high affinity. Advantages compared with those of natural receptors include their excellent thermal and chemical stability, low cost, and ease of the production process. However, their use in commercial biosensors is limited owing to the difficulty to incorporate MIPs into suitable sensing platforms and traditional detection techniques, such as chromatography, that require bulky and sophisticated equipment. In this review, we evaluate the potential to use MIPs combined with thermal read-out for the detection of low-weight organic molecules. We discuss thermal methods to study MIP-template complexation and to determine neurotransmitters concentrations. In particular, we highlight the heat-transfer method, a recent technique that is straightforward and low cost and requires minimal instrumentation. Until now, sample preparation involves a 2-step process, making it time-consuming, and measuring biological samples is difficult owing to the noise in the signal. Different sample preparation methods are discussed, and it will be demonstrated how this affects the thermal response. An outlook is given in novel methods that can simplify and speed up sample preparation. Finally, we show a novel thermal technique, which is based on the analysis of transport of thermal waves rather than evaluating the fixed heat-transfer resistance. Through applying the concept of thermal waves, signal-noise ratio is significantly increased, which results in lower detection limits and has potential for the study of biological samples.

Molecularly imprinted polymers as synthetic receptors for the QCM-D-based detection of L-nicotine in diluted saliva and urine samples.

Molecularly imprinted polymers (MIPs) are synthetic receptors that are able to specifically bind their target molecules in complex samples, making them a versatile tool in biosensor technology. The combination of MIPs as a recognition element with quartz crystal microbalances (QCM-D with dissipation monitoring) gives a straightforward and sensitive device, which can simultaneously measure frequency and dissipation changes. In this work, bulk-polymerized L-nicotine MIPs were used to test the feasibility of L-nicotine detection in saliva and urine samples. First, L-nicotine-spiked saliva and urine were measured after dilution in demineralized water and 0.1× phosphate-buffered saline solution for proof-of-concept purposes. L-nicotine could indeed be detected specifically in the biologically relevant micromolar concentration range. After successfully testing on spiked samples, saliva was analyzed, which was collected during chewing of either nicotine tablets with different concentrations or of smokeless tobacco. The MIPs in combination with QCM-D were able to distinguish clearly between these samples: This proves the functioning of the concept with saliva, which mediates the oral uptake of nicotine as an alternative to the consumption of cigarettes.

Heat-transfer-based detection of L-nicotine, histamine, and serotonin using molecularly imprinted polymers as biomimetic receptors.

In this work, we will present a novel approach for the detection of small molecules with molecularly imprinted polymer (MIP)-type receptors. This heat-transfer method (HTM) is based on the change in heat-transfer resistance imposed upon binding of target molecules to the MIP nanocavities. Simultaneously with that technique, the impedance is measured to validate the results. For proof-of-principle purposes, aluminum electrodes are functionalized with MIP particles, and L-nicotine measurements are performed in phosphate-buffered saline solutions. To determine if this could be extended to other templates, histamine and serotonin samples in buffer solutions are also studied. The developed sensor platform is proven to be specific for a variety of target molecules, which is in agreement with impedance spectroscopy reference tests. In addition, detection limits in the nanomolar range could be achieved, which is well within the physiologically relevant concentration regime. These limits are comparable to impedance spectroscopy, which is considered one of the state-of-the-art techniques for the analysis of small molecules with MIPs. As a first demonstration of the applicability in biological samples, measurements are performed on saliva samples spiked with L-nicotine. In summary, the combination of MIPs with HTM as a novel readout technique enables fast and low-cost measurements in buffer solutions with the possibility of extending to biological samples.

Towards water compatible MIPs for sensing in aqueous media.

When synthesizing molecularly imprinted polymers (MIPs), a few fundamental principles should be kept in mind. There is a strong correlation between porogen polarity, MIP microenvironment polarity and the imprinting effect itself. The combination of these parameters eventually determines the overall binding behavior of a MIP in a given solvent. In addition, it is shown that MIP binding is strongly influenced by the polarity of the rebinding solvent. Because the use of MIPs in biomedical environments is of considerable interest, it is important that these MIPs perform well in aqueous media. In this article, various approaches are explored towards a water compatible MIP for the target molecule l-nicotine. To this end, the imprinting effect together with the MIP matrix polarity is fine-tuned during MIP synthesis. The binding behavior of the resulting MIPs is evaluated by performing batch rebinding experiments that makes it possible to select the most suitable MIP/non-imprinted polymer couple for future application in aqueous environments. One method to achieve improved compatibility with water is referred to as porogen tuning, in which porogens of varying polarities are used. It is demonstrated that, especially when multiple porogens are mixed, this approach can lead to superior performance in aqueous environments. Another method involves the incorporation of polar or non-polar comonomers in the MIP matrix. It is shown that by carefully selecting these monomers, it is also possible to obtain MIPs, which can selectively bind their target in water.

Synthesis, 1H and 13C NMR assignment and electrochemical properties of novel thiophene-thiazolothiazole oligomers and polymers.

Novel hexyl-substituted bisthiophene compounds containing a thiazolothiazole(5,4-d) unit have been explored. The molecules are soluble in common organic solvents, which would enhance their chance of possible integration in printable electronics. Synthesis and complete elucidation of the chemical structures by detailed 1D/2D NMR spectroscopy are described. This provides interesting input for chemical shift prediction software, because few experimental data on this type of compounds are available. Furthermore, the potential n-type character of these derivatives is verified using electrochemical measurements. In addition, the low-bandgap character of conjugated polymers containing the thiazolothiazole unit is demonstrated by performing an electropolymerization.

A MIP-based impedimetric sensor for the detection of low-MW molecules.

Mimicking the selectivity and sensitivity of biological systems for sensor devices is of increasing interest in biomedical, environmental and chemical analysis. Synthetic materials with imprinted nanocavities, acting as highly selective artificial receptors, are a tailor-made solution in obtaining such a sensor. Incorporation of such molecularly imprinted polymers (MIPs) in a platform suitable for electrochemical measurements, can offer high sensitivity together with device miniaturization and an electronic read-out. As a proof of principle, a MIP-based sensor for L-nicotine has been developed. To this end, the molecular structure of L-nicotine was imprinted in a polymer matrix of polymethacrylic acid (PMAA). Subsequently, microparticles of the imprinted polymer were immobilized on thin films of the conjugated polymer OC(1)C(10)-PPV. These films were incorporated in an impedimetric sensing device. Using electrochemical impedance spectroscopy, the real part of the impedance was monitored for various concentrations. This setup allows for the detection of l-nicotine from 1 to 10 nM and is insensitive for the resembling molecule L-cotinine.

A novel thermal detection method based on molecularly imprinted nanoparticles as recognition elements.

Molecularly Imprinted Polymers (MIPs) are synthetic receptors that are able to selectively bind their target molecule and, for this reason, they are currently employed as recognition elements in sensors. In this work, MIP nanoparticles (nanoMIPs) are produced by solid-phase synthesis for a range of templates with different sizes, including a small molecule (biotin), two peptides (one derived from the epithelial growth factor receptor and vancomycin) and a protein (trypsin). NanoMIPs are then dipcoated on the surface of thermocouples that measure the temperature inside a liquid flow cell. Binding of the template to the MIP layer on the sensitive area of the thermocouple tip blocks the heat-flow from the sensor to the liquid, thereby lowering the overall temperature measured by the thermocouple. This is subsequently correlated to the concentration of the template, enabling measurement of target molecules in the low nanomolar regime. The significant improvement in the limit of detection (a magnitude of three orders compared to previously used MIP microparticles) can be attributed to their high affinity, enhanced conductivity and increased surface-to-volume ratio. It is the first time that these nanosized recognition elements are used in combination with thermal detection, and it is the first report on MIP-based thermal sensors for determining protein levels. The developed thermal sensors have a high selectivity, fast measurement time (<5 min), and data analysis is straightforward, which makes it possible to monitor biomolecules in real-time. The set of biomolecules discussed in this manuscript show that it is possible to cover a range of template molecules regardless of their size, demonstrating the general applicability of the biosensor platform. In addition, with its high commercial potential and biocompatibility of the MIP receptor layer, this is an important step towards sensing assays for diagnostic applications that can be used in vivo.

Fingerprints for structural defects in poly(thienylene vinylene) (PTV): a joint theoretical-experimental NMR study on model molecules.

In the field of plastic electronics, low band gap conjugated polymers like poly(thienylene vinylene) (PTV) and its derivatives are a promising class of materials that can be obtained with high molecular weight via the so-called dithiocarbamate precursor route. We have performed a joint experimental-theoretical study of the full NMR chemical shift assignment in a series of thiophene-based model compounds, which aims at (i) benchmarking the quantum-chemical calculations against experiments, (ii) identifying the signature of possible structural defects that can appear during the polymerization of PTV's, namely head-to-head and tail-to-tail defects, and (iii) defining a criterion regarding regioregularity.

The band 12 issue in the electron momentum spectra of norbornane: a comparison with additional Green's Function calculations and ultraviolet photoemission measurements.

In continuation of a recent study of the electronic structure of norbornane [J. Chem. Phys., 2004, 121, 10525] by means of electron momentum spectroscopy (EMS), we present Green's Function calculations of the ionization spectrum of this compound at the ADC(3) level using basis sets of varying quality, along with accurate evaluations at the CCSD(T) level of the vertical (26.5 eV) and adiabatic (22.1 eV) double ionization thresholds under C(2v) symmetry. The obtained results are compared with newly recorded ultraviolet photoemission spectra (UPS), up to binding energies of 40 eV. The theoretical predictions are entirely consistent with experiment and indicate that, in a vertical depiction of ionization, shake-up states at binding energies larger than approximately 26.5 eV tend to decay via emission of a second electron in the continuum. A band of s-type symmetry that has been previously seen at approximately 25 eV in the electron impact ionization spectra of norbornane is entirely missing in the UPS measurements and theoretical ADC(3) spectra. With regard to these results and to the time scales characterizing electron-electron interactions in EMS (10(-17) s) as compared with that (10(-13) s) of photon-electron interactions in UPS, and considering the p-type symmetry of the electron momentum distributions for the nearest 1b(1) and 1b(2) orbitals, this additional band can certainly not be due to adiabatic double ionization processes starting from the ground electronic state of norbornane, or to exceptionally strong vibronic coupling interactions between cationic states derived from ionization of the latter orbitals. It is therefore tentatively ascribed to autoionization processes via electronically excited and possibly dissociating states.