Polymer Micropillar Arrays for Colorimetric DNA Detection.

We describe the use of periodic micropillar arrays, produced from cyclic olefin copolymer using high-fidelity microfabrication, as templates for colorimetric DNA detection. The assay involves PCR-amplified gene markers for E. coli O157:H7 (rfbO157, eae, vt1, and vt2) incorporating a detectable digoxigenin label, which is revealed through an immunoenzymatic process following hybridization with target-specific oligonucleotide capture probes. The capacity of micropillar arrays to induce wicking is used to distribute and confine capture probes with spatial control, making it possible to achieve a uniform signal while allowing multiple, independent probes to be arranged in close proximity on the same substrate. The kinetic profile of color pigment formation on the surface was followed using absorbance measurements, showing maximum signal increase between 20 and 60 min of reaction time. The relationship between microstructure and colorimetric signal was investigated through variation of geometric parameters, such as pitch (10-50 µm), pillar diameter (5-40 µm), and height (16-48 µm). Our findings suggest that signal intensity is largely influenced by the edges of the pillars and less by their height such that it deviates from a linear relationship when both aspect ratio and pillar density become very high. A theoretical model used to simulate the changes in surface composition at the molecular level suggests that differences in the temporal and spatial accumulation of assay components account for this observation.

Centrifugal microfluidic lab-on-a-chip system with automated sample lysis, DNA amplification and microarray hybridization for identification of enterohemorrhagic Escherichia coli culture isolates.

The development of technology for the rapid, automated identification of bacterial culture isolates can help regulatory agencies to shorten response times in food safety surveillance, compliance, and enforcement as well as outbreak investigations. While molecular methods such as polymerase chain reaction (PCR) enable the identification of microbial organisms with high sensitivity and specificity, they generally rely on sophisticated instrumentation and elaborate workflows for sample preparation with an undesirably high level of hands-on engagement. Herein, we describe the design, operation and performance of a lab-on-a-chip system integrating thermal lysis, PCR amplification and microarray hybridization on the same cartridge. The assay is performed on a centrifugal microfluidic platform that allows for pneumatic actuation of liquids during rotation, making it possible to perform all fluidic operations in a fully-automated fashion without the need for integrating active control elements on the microfluidic cartridge. The cartridge, which is fabricated from hard and soft thermoplastic polymers, is compatible with high-volume manufacturing (e.g., injection molding). Chip design and thermal interface were both optimized to ensure efficient heat transfer and allow for fast thermal cycling during the PCR process. The integrated workflow comprises 14 steps and takes less than 2 h to complete. The only manual steps are related to loading of the sample and reagents on the cartridge as well as fluorescence imaging of the microarray. On-chip lysis and PCR amplification both provided results comparable to those obtained by bench-top instrumentation. The microarray, incorporating a panel of oligonucleotide probes for multiplexed detection of seven enterohemorrhagic E. coli priority serotypes, was implemented on a cyclic olefin copolymer substrate using a novel activation scheme that involves the conversion of hydroxyl groups (derived from oxygen plasma treatment) into reactive cyanate ester using cyanogen bromide. On-chip hybridization was demonstrated in a non-quantitative fashion using fluorescently-labelled gene markers for E. coli O157:H7 (rfbO157, eae, vt1, and vt2) obtained through a multiplexed PCR amplification step.

Genetic characterization of norovirus GII.4 variants circulating in Canada using a metagenomic technique.

BACKGROUND: Human norovirus is the leading cause of viral gastroenteritis globally, and the GII.4 has been the most predominant genotype for decades. This genotype has numerous variants that have caused repeated epidemics worldwide. However, the molecular evolutionary signatures among the GII.4 variants have not been elucidated throughout the viral genome. METHOD: A metagenomic, next-generation sequencing method, based on Illumina RNA-Seq, was applied to determine norovirus sequences from clinical samples. RESULTS: Herein, the obtained deep-sequencing data was employed to analyze full-genomic sequences from GII.4 variants prevailing in Canada from 2012 to 2016. Phylogenetic analysis demonstrated that the majority of these sequences belong to New Orleans 2009 and Sydney 2012 strains, and a recombinant sequence was also identified. Genome-wide similarity analyses implied that while the capsid gene is highly diverse among the isolates, the viral protease and polymerase genes remain relatively conserved. Numerous amino acid substitutions were observed at each putative antigenic epitope of the VP1 protein, whereas few amino acid changes were identified in the polymerase protein. Co-infection with other enteric RNA viruses was investigated and the astrovirus genome was identified in one of the samples. CONCLUSIONS: Overall this study demonstrated the application of whole genome sequencing as an important tool in molecular characterization of noroviruses.

Microfluidic Integration of a Cloth-Based Hybridization Array System (CHAS) for Rapid, Colorimetric Detection of Enterohemorrhagic Escherichia coli (EHEC) Using an Articulated, Centrifugal Platform.

We describe the translation of a cloth-based hybridization array system (CHAS), a colorimetric DNA detection method that is used by food inspection laboratories for colony screening of pathogenic agents, onto a microfluidic chip format. We also introduce an articulated centrifugal platform with a novel fluid manipulation concept based on changes in the orientation of the chip with respect to the centrifugal force field to time the passage of multiple components required for the process. The platform features two movable and motorized carriers that can be reoriented on demand between 0 and 360° during stage rotation. Articulation of the chip can be used to trigger on-the-fly fluid dispensing through independently addressable siphon structures or to relocate solutions against the centrifugal force field, making them newly accessible for downstream transfer. With the microfluidic CHAS, we achieved significant reduction in the size of the cloth substrate as well as the volume of reagents and wash solutions. Both the chip design and the operational protocol were optimized to perform the entire process in a reliable, fully automated fashion. A demonstration with PCR-amplified genomic DNA confirms on-chip detection and identification of Escherichia coli O157:H7 from colony isolates in a colorimetric multiplex assay using rfbO157, fliCH7, vt1, and vt2 genes.

Enhancing the Detection of Giardia duodenalis Cysts in Foods by Inertial Microfluidic Separation.

The sensitivity and specificity of current Giardia cyst detection methods for foods are largely determined by the effectiveness of the elution, separation, and concentration methods used. The aim of these methods is to produce a final suspension with an adequate concentration of Giardia cysts for detection and a low concentration of interfering food debris. In the present study, a microfluidic device, which makes use of inertial separation, was designed and fabricated for the separation of Giardia cysts. A cyclical pumping platform and protocol was developed to concentrate 10-ml suspensions down to less than 1 ml. Tests involving Giardia duodenalis cysts and 1.90-µm microbeads in pure suspensions demonstrated the specificity of the microfluidic chip for cysts over smaller nonspecific particles. As the suspension cycled through the chip, a large number of beads were removed (70%) and the majority of the cysts were concentrated (82%). Subsequently, the microfluidic inertial separation chip was integrated into a method for the detection of G. duodenalis cysts from lettuce samples. The method greatly reduced the concentration of background debris in the final suspensions (10-fold reduction) in comparison to that obtained by a conventional method. The method also recovered an average of 68.4% of cysts from 25-g lettuce samples and had a limit of detection (LOD) of 38 cysts. While the recovery of cysts by inertial separation was slightly lower, and the LOD slightly higher, than with the conventional method, the sample analysis time was greatly reduced, as there were far fewer background food particles interfering with the detection of cysts by immunofluorescence microscopy.

Microfluidic filtration and extraction of pathogens from food samples by hydrodynamic focusing and inertial lateral migration.

Detecting pathogenic bacteria in food or other biological samples with lab-on-a-chip (LOC) devices requires several sample preparation steps prior to analysis which commonly involves cleaning complex sample matrices of large debris. This often underestimated step is important to prevent these larger particles from clogging devices and to preserve initial concentrations when LOC techniques are used to concentrate or isolate smaller target microorganisms for downstream analysis. In this context, we developed a novel microfluidic system for membrane-free cleaning of biological samples from debris particles by combining hydrodynamic focusing and inertial lateral migration effects. The microfluidic device is fabricated using thermoplastic elastomers being compatible with thermoforming fabrication techniques leading to low-cost single-use devices. Microfluidic chip design and pumping protocols are optimized by investigating diffusive losses numerically with coupled Navier-Stokes and convective-diffusion theoretical models. Stability of inertial lateral migration and separation of debris is assessed through fluorescence microscopy measurements with labelled particles serving as a model system. Efficiency of debris cleaning is experimentally investigated by monitoring microchip outlets with in situ optical turbidity sensors, while retention of targeted pathogens (i.e., Listeria monocytogenes) within the sample stream is assessed through bacterial culture techniques. Optimized pumping protocols can remove up to 50 % of debris from ground beef samples while percentage for preserved microorganisms can account for 95 % in relatively clean samples. However, comparison between inoculated turbid and clean samples (i.e., with and without ground beef debris) indicate some degree of interference between debris inertial lateral migration and hydrodynamic focusing of small microorganisms. Although this interference can lead to significant decrease in chip performance through loss of target bacteria, it remains possible to reach 70 % for sample recovery and more than 50 % for debris removal even in the most turbid samples tested. Due to the relatively simple design, the robustness of the inertial migration effect itself, the high operational flow rates and fabrication methods that leverage low-cost materials, the proposed device can have an impact on a wide range of applications where high-throughput separation of particles and biological species is of interest.

Centrifugal microfluidic system for colorimetric sample-to-answer detection of viral pathogens.

We describe a microfluidic system for conducting thermal lysis, polymerase chain reaction (PCR) amplification, hybridization, and colorimetric detection of foodborne viral organisms in a sample-to-answer format. The on-chip protocol entails 24 steps which are conducted by a centrifugal platform that allows for actuating liquids pneumatically during rotation and so facilitates automation of the workflow. The microfluidic cartridge is fabricated from transparent thermoplastic polymers and accommodates assay components along with an embedded micropillar array for detection and read-out. A panel of oligonucleotide primers and probes has been developed to perform PCR and hybridization assays that allows for identification of five different viruses, including pathogens such as norovirus and hepatitis A virus (HAV) in a multiplexed format using digoxigenin-labelled amplicons and immunoenzymatic conversion of a chromogenic substrate. Using endpoint detection, we demonstrate that the system can accurately and repetitively (n = 3) discriminate positive and negative signals for HAV at 350 genome copies per µL. As part of the characterization and optimization process, we show that the implementation of multiple (e.g., seven) micropillar arrays in a narrow fluidic pathway can lead to variation (up to 50% or more) in the distribution of colorimetric signal deriving from the assay. Numerical modeling of flow behaviour was used to substantiate these findings. The technology-by virtue of automation-can provide a pathway toward rapid detection of viral pathogens, shortening response time in food safety surveillance, compliance, and enforcement as well as outbreak investigations.

Automated centrifugal microfluidic system for the preparation of adaptor-ligated sequencing libraries.

The intensive workload associated with the preparation of high-quality DNA libraries remains a key obstacle toward widespread deployment of sequencing technologies in remote and resource-limited areas. We describe the development of single-use microfluidic devices driven by an advanced pneumatic centrifugal microfluidic platform, the PowerBlade, to automate the preparation of Illumina-compatible libraries based on adaptor ligation methodology. The developed on-chip workflow includes enzymatic DNA fragmentation coupled to end-repair, adaptor ligation, first DNA cleanup, PCR amplification, and second DNA cleanup. This complex workflow was successfully integrated into simple thermoplastic microfluidic devices that are amenable to mass production with injection molding. The system was validated by preparing, on chip, libraries from a mixture of genomic DNA extracted from three common foodborne pathogens (Listeria monocytogenes, Escherichia coli and Salmonella enterica serovar Typhimurium) and comparing them with libraries made via a manual procedure. The two types of libraries were found to exhibit similar quality control metrics (including genome coverage, assembly, and relative abundances) and led to nearly uniform coverage independent of GC content. This microfluidic technology offers a time-saving and cost-effective alternative to manual procedures and robotic-based automation, making it suitable for deployment in remote environments where technical expertise and resources might be scarce. Specifically, it facilitates field practices that involve mid- to low-throughput sequencing, such as tasks related to foodborne pathogen detection, characterization, and microbial profiling.

Survival and Inactivation by Advanced Oxidative Process of Foodborne Viruses in Model Low-Moisture Foods.

Enteric viruses, such as human norovirus (NoV) and hepatitis A virus (HAV), are the major causes of foodborne illnesses worldwide. These viruses have low infectious dose, and may remain infectious for weeks in the environment and food. Limited information is available regarding viral survival and transmission in low-moisture foods (LMF). LMFs are generally considered as ready-to-eat products, which undergo no or minimal pathogen reduction steps. However, numerous foodborne viral outbreaks associated with LMFs have been reported in recent years. The objective of this study was to examine the survival of foodborne viruses in LMFs during 4-week storage at ambient temperature and to evaluate the efficacy of advanced oxidative process (AOP) treatment in the inactivation of these viruses. For this purpose, select LMFs such as pistachios, chocolate, and cereal were inoculated with HAV and the norovirus surrogates, murine norovirus (MNV) and feline calicivirus (FCV), then viral survival on these food matrices was measured over a four-week incubation at ambient temperature, by both plaque assay and droplet-digital RT-PCR (ddRT-PCR) using the modified ISO-15216 method as well as the magnetic bead assay for viral recovery. We observed an approximately 0.5 log reduction in viral genome copies, and 1 log reduction in viral infectivity for all three tested viruses following storage of select inoculated LMFs for 4 weeks. Therefore, the present study shows that the examined foodborne viruses can persist for a long time in LMFs. Next, we examined the inactivation efficacy of AOP treatment, which combines UV-C, ozone, and hydrogen peroxide vapor, and observed that while approximately 100% (4 log) inactivation can be achieved for FCV, and MNV in chocolate, the inactivation efficiency diminishes to approximately 90% (1 log) in pistachios and 70% (< 1 log) in cereal. AOP treatment could therefore be a good candidate for risk reduction of foodborne viruses from certain LMFs depending on the food matrix and surface of treatment.

A cloth-based hybridization array system for rapid detection of the food- and waterborne protozoan parasites Giardia duodenalis, Cryptosporidium spp. and Toxoplasma gondii.

Protozoan parasites in food or water samples are generally detected using microscopy or PCR followed by Sanger sequencing. However, microscopy is subjective, requires a high degree of expertise and has limited sensitivity, while DNA sequencing requires expensive and specialized equipment and facilities. This study describes a cloth-based hybridization array system (CHAS) that is an alternative to Sanger sequencing to confirm PCR-positive samples. CHAS is an inexpensive, rapid and reliable method for the simultaneous detection of multiple protozoan parasite species based on the colorimetric detection of PCR amplicons on a polyester cloth. PCR primers and CHAS hybridization probes were developed to detect the protozoan parasites Giardia duodenalis, Cryptosporidium spp. and Toxoplasma gondii. In addition, CHAS probes were designed for the differentiation of G. duodenalis Assemblages A and B. In artificially contaminated fresh produce (lettuce, parsley) and water samples (river water, wastewater), this CHAS assay allowed for the successful detection of G. duodenalis, Cryptosporidium spp., and T. gondii. The present study demonstrates that the CHAS detection method is a simple and inexpensive alternative to DNA sequencing for the confirmation of PCR-positive results in laboratories testing for parasites in food or water samples. This assay may also be beneficial in developing countries, where DNA sequencing facilities may not be readily available.

Evaluation of Bead-Based Assays for the Isolation of Foodborne Viruses from Low-Moisture Foods.

ABSTRACT: Foodborne viruses such as norovirus and hepatitis A virus (HAV) are highly transmissible, persistent in the environment, and resistant to many conventional inactivation methods. Foods can become contaminated with these viruses either at the source of harvest or during food handling and processing. Multiple lines of evidence suggest that foodborne viruses can survive desiccation and dry conditions. Several foodborne virus outbreaks have been linked to low-moisture foods (LMFs), indicating that these foods can be vehicles of virus transmission. However, the efficiencies of common virus extraction methodologies have not been examined with LMFs. We adapted the International Organization for Standardization (ISO) 15216-1:2017 method for virus recovery for use with chocolate, pistachios, and cornflakes. We also developed a magnetic bead assay for the recovery of HAV from LMFs and used the porcine gastric mucin-coated magnetic beads (PGM-MBs) to extract norovirus surrogates, feline calicivirus (FCV), and murine norovirus (MNV) from the same LMFs. The efficiency of virus recovery using the bead-based assay was then compared with that of the ISO 15216-1:2017 method. In chocolate and pistachios, the recovery rates with the PGM-MB method were 5.6- and 21.3-fold higher, respectively, for FCV and 1.65- and 18-fold higher, respectively, for MNV than those with the ISO 15216-1:2017 method. However, the PGM-MB method failed to recover MNV and FCV from cornflakes. The recovery rates for HAV in chocolate, pistachios, and corn flakes with the magnetic bead method were 11.5-, 3-, and 5.6-fold higher, respectively, than those with the ISO 15216-1:2017 method. Thus, depending upon the food matrix and the target virus, the bead-based assays can be used to efficiently and rapidly extract viruses from LMFs.

Development of a DNA microarray for the simultaneous detection and genotyping of noroviruses.

Current methods for detecting and genotyping noroviruses focus on the use of reverse transcriptase (RT)-mediated PCR. A major drawback of this approach is that short target RT-PCR products do not always encompass sequences that can be compared among research laboratories, resulting in difficulties for molecular epidemiology. We describe the use of a microarray-based system for simultaneous detection and molecular characterization of noroviruses. The protocol generates a 917-bp RT-PCR product that encompasses two major regions currently used for detection and analysis of norovirus genomes. The PCR products are then hybridized to an oligonucleotide array (NoroChip) based on 50-mer features, which allows for both confirmation of reaction specificity and molecular characterization of the amplified genome. Parallel sequence analyses of amplicons revealed that our microarray data were robust in separating genogroups I and II, and further subtyping to the cluster level was possible. This approach, combining detection and characterization, overcomes the need for expensive and time-consuming sequence analysis of amplified genome targets for molecular epidemiology.

Characterization of the Genomic Diversity of Norovirus in Linked Patients Using a Metagenomic Deep Sequencing Approach.

Norovirus (NoV) is the leading cause of gastroenteritis worldwide. A robust cell culture system does not exist for NoV and therefore detailed characterization of outbreak and sporadic strains relies on molecular techniques. In this study, we employed a metagenomic approach that uses non-specific amplification followed by next-generation sequencing to whole genome sequence NoV genomes directly from clinical samples obtained from 8 linked patients. Enough sequencing depth was obtained for each sample to use a de novo assembly of near-complete genome sequences. The resultant consensus sequences were then used to identify inter-host nucleotide variations that occur after direct transmission, analyze amino acid variations in the major capsid protein, and provide evidence of recombination events. The analysis of intra-host quasispecies diversity was possible due to high coverage-depth. We also observed a linear relationship between NoV viral load in the clinical sample and the number of sequence reads that could be attributed to NoV. The method demonstrated here has the potential for future use in whole genome sequence analyses of other RNA viruses isolated from clinical, environmental, and food specimens.

Prevalence and Molecular Characterization of the Hepatitis E Virus in Retail Pork Products Marketed in Canada.

Infection with the hepatitis E virus (HEV) is very common worldwide. HEV causes acute viral hepatitis with approximately 20 million cases per year. While HEV genotypes 1 and 2 cause large waterborne and foodborne outbreaks with a significant mortality in developing countries, genotypes 3 and 4 are more prevalent in developed countries with transmission being mostly zoonotic. In North America and Europe, HEV has been increasingly detected in swine, and exposure to pigs and pork products is considered to be the primary source of infection. Therefore we set out to investigate the prevalence of HEV in retail pork products available in Canada, by screening meal-size portions of pork pâtés, raw pork sausages, and raw pork livers. The presence of the HEV genomes was determined by RT-PCR and viral RNA was quantified by digital droplet PCR. Overall, HEV was detected in 47% of the sampled pork pâtés and 10.5% of the sampled raw pork livers, but not in the sampled pork sausages, and sequencing confirmed that all HEV strains belonged to genotype 3. Further phylogenetic analysis revealed that except for one isolate that clusters with subtype 3d, all isolates belong to subtype 3a. Amino acid variations between the isolates were also observed in the sequenced capsid region. In conclusion, the prevalence of HEV in pâtés and raw pork livers observed in this study is in agreement with the current HEV distribution in pork products reported in other developed countries.

Rapid Screening and Identification of Living Pathogenic Organisms via Optimized Bioorthogonal Non-canonical Amino Acid Tagging.

Pathogenic bacteria can be a major cause of illness from environmental sources as well as the consumption of contaminated products, giving rise to public health concerns globally. The surveillance of such living organisms in food and water supplies remains an important challenge in mitigating their deleterious societal effects. Here, we have developed an optimized bioorthogonal non-canonical amino acid tagging approach to the imaging, capture, and interrogation of shigatoxigenic/verotoxigenic Escherichia coli (VTEC) and Listeria that enables the distinction between living wild-type pathogenic bacteria. The approaches utilize homopropargylglycine (HPG), as well as optimized growth media, that restricts endogenous methionine biosynthesis in a variety of species of public health concern. Endogenous methionine residues are then replaced with HPG, which can then be modified using a myriad of compatible bioorthogonal reactions for tagging of exclusively live bacteria. The methods reported allow for the very rapid screening and identification of living pathogenic organisms.

Development and validation of a microarray for the confirmation and typing of norovirus RT-PCR products.

Noroviruses are implicated in many worldwide institutional, food and waterborne outbreaks each year. Genetic typing of isolates is valuable for monitoring outbreak spread as well as variation in circulating strains. Microarrays have the potential to provide rapid genotype information for norovirus samples. The NoroChip v3.0 provides an oligonucleotide hybridization platform to screen for over 600 potential interactions in each experiment. The NoroChip v3.0 was developed at Health Canada and validated in seven international partner laboratories. Each laboratory validated the NoroChip v3.0 using norovirus amplicons routinely characterized in their testing protocols. Fragments from the capsid region (region C) and a 2.4 kb amplicon spanning polymerase and capsid sequences (region AD) were validated in six of the partner laboratories and provided correct genogroup typing information (GI or GII) when hybridized to the NoroChip v3.0. Results indicate that the current limiting factor for implementing the NoroChip v3.0 as a strain typing tool is the difficulty obtaining a long, specific amplicon from all circulating norovirus strains. Data obtained with the longer region AD amplicon provided the best discrimination between norovirus strains.

Molecular characterization of three plasmids from Bifidobacterium longum.

The complete nucleotide sequences for pNAC1 (3538bp) from strain RW048 as well as for pNAC2 (3684bp) and pNAC3 (10,224bp) from strain RW041 of Bifidobacterium longum were determined. The largest ORF (repB) of pNAC1 encodes a putative protein similar to those involved in a rolling-circle (RC) replication mechanism, which was confirmed by demonstration of single-strand intermediates in the host cell. The putative RepB gene product of pNAC2 is most similar to the replication protein of pDOJH10L and pKJ36. A second gene (mob) is similar to mobilization proteins involved in conjugation. Plasmid pNAC3 is the largest bifidobacterial plasmid to be sequenced to date. Of the eight putative gene products coded by pNAC3, one is similar to replication proteins (RepB), and another (Orf2) to putative transfer proteins (Tra). Bifidobacterial plasmids were divided into five groups based on Rep amino acid sequence homology and the results suggest a new plasmid family for B. longum.