RESUMO
The purpose of this in-vitro study was to compare trueness, 3D deviation, production time and costs of milled and 3D-printed resin single crowns. A total of 20 CAD-CAM resin single crowns were fabricated from 10 digital wax patterns designed on 10 tooth preparations available in a reference model. Standardized control linear measurements were performed with a CAD software. Each STL file was then used to fabricate two resins crowns - one milled and one 3D-printed. All crowns underwent physical linear measurements using a digital caliper. The crowns were then scanned using an intraoral scanner for assessing 3D deviation. Finally, time to produce a single crown, as well as costs and production rates of both methods were also compared. Both CAM methods did not present statistically significant differences in linear measurements, as compared to controls (P⟩.05). Furthermore, 3D-printed crowns had significantly greater deviations in cervical margins (P=.032) and occlusal surfaces (P=.041), as compared with milled crowns. Finally, 3D-printing took significantly longer to produce one single crown (P=.001), but with a cheaper and higher production rate than milling. These findings suggest that milling devices produce resin single crowns with smaller 3D deviations but more expensive costs, as compared with low-cost 3D printers.
Assuntos
Desenho Assistido por Computador , Coroas , Custos e Análise de Custo , Adaptação Marginal Dentária , Planejamento de Prótese Dentária , Impressão Tridimensional , SoftwareRESUMO
PURPOSE: Intraoral scanning subgingival finish lines has been described as challenging. The purpose of this study was to assess the impact of gingival contour around margins of implant stock abutments on marginal fit of Computer-aided Design - Computer-aided Manufacturing (CAD-CAM) zirconia copings. This in-vitro study was conducted on 40 analogues of implant stock abutments that were embedded into individual phantoms composed by a resin block. All 40 phantoms underwent two intraoral scans - one with (test group) and one without artificial gingiva (control group) - using a closed system intraoral scanner. Zirconia copings were then digitally designed and milled, followed by high-speed sintering, before being analyzed for marginal adaptation and internal surface roughness with scanning electron microscopy. Statistically significant differences between groups were assessed with the Mann-Whitney test. Median marginal gap values were 149.78 µm (95% CI: 112.39-216.66) for the test group and 94.90 µm (95% CI: 83.89-107.74) for the control group. A statistically significant difference was found between groups (p=0.0001). However, there were no subjective differences between groups for internal surface roughness. Within the limitations of this study, the present findings suggest that a gingival contour one millimeter higher than the finishing line affects marginal adaptation of CAD-CAM zirconia copings.
Assuntos
Implantes Dentários , Adaptação Marginal Dentária , Adaptação Psicológica , Desenho Assistido por Computador , Coroas , Planejamento de Prótese Dentária , Gengiva , ZircônioRESUMO
OBJECTIVES: This review aimed to compare traditional and digital methods to assess marginal gaps in fixed dental prostheses. Each method's characteristics, advantages, and limitations were identified and discussed, also addressing the knowledge gaps in the current scientific literature. DATA: Studies comparing currently available techniques for marginal gap examination were investigated. The main techniques analyzed were the Cross-Sectional Method (CSM), Direct View (DV), Silicone Replica Technique (SRT), Dual-Scan Method (DSM), Triple-Scan Method (TSM), Optical Coherence Tomography (OCT), and Micro-Computed Tomography (MCT). SOURCES: Two experienced independent reviewers screened online databases (MEDLINE via PubMed and Scopus) to identify studies published in English up to March 2024. References from primary studies and the main peer-reviewed scientific journals were manually searched. STUDY SELECTION: From an initial pool of 8126 articles, the reviewers meticulously selected 25 in vitro studies on objective comparisons between two or more methods for assessing marginal gaps in fixed dental prostheses on natural teeth. Publications that assessed marginal gaps in implant-supported fixed dental prostheses were excluded. CONCLUSIONS: This study highlights that while traditional methods like CSM and SRT are widely used and validated, they have limitations in comprehensive gap assessment, often neglecting recommended measurement points. The DV technique, focusing solely on external gaps, may be less relevant for modern assessments. Conversely, three-dimensional techniques like TSM, DSM, OCT, and MCT offer a more thorough evaluation of dental restoration fit. Moreover, digital methods such as TSM and DSM have a significant potential for future clinical application. CLINICAL SIGNIFICANCE: This review examined methods for evaluating marginal gaps in fixed dental prostheses. The review aids dental professionals and researchers in choosing the most suitable technique for clinical in vivo or laboratory assessment of the marginal adaptation of dental restorations. This study also indicates the need for an established and standardized assessment protocol for the marginal fit.
RESUMO
BACKGROUND: The risk of femoral neck fracture progressively increases with age. However, the reasons behind this consistent increase in the fracture risk can't be completely justified by the decrease in the bone mineral density. The objective of this study was to analyze the correlation between various bone structural features and age. STUDY DESIGN & METHODS: A total of 29 consecutive patients who suffered an intracapsular hip fracture and underwent joint replacement surgery between May 2012 and March 2013 were included in this study. A 2 cm × 1 cm Ø cylindrical trabecular bone sample was collected from the femoral heads and preserved in formaldehyde. Bone mineral density (BMD), microarchitecture, organic content and crystallography were analyzed using a Dual-energy X-ray absorptiometry scan, micro-CT scan, and high resolution magic-angle-spinning-nuclear magnetic resonance (MAS-NMR), respectively. Statistical correlations were made using Spearman´s or Pearson´s correlation tests depending on the distribution of the continuous variables. RESULTS: The mean patient age was 79.83 ± 9.31 years. A moderate negative correlation was observed between age and the hydrogen content in bone (1H), which is an indirect estimate to quantify the organic matrix (r = -0.512, p = 0.005). No correlations were observed between BMD, trabecular number, trabecular thickness, phosphorous content, apatite crystal size, and age (r = 0.06, p = 0.755; r = -0.008, p = 0.967; r = -0.046, p = 0.812; r = -0.152, p = 0.430, respectively). A weak positive correlation was observed between Charlson´s comorbidity index (CCI) and c-axis of the hydroxiapatite (HA) crystals (r = -0.400, p = 0.035). CONCLUSION: The femoral head relative protein content progressively decreases with age. BMD was not correlated with other structural bone parameters and age. Patients with higher comorbidity scores had larger HA crystals. The present results suggest that the progressive increase in the hip fracture risk in elderly patients could be partially explained by the lower bone protein content in this age group.
Assuntos
Envelhecimento/fisiologia , Densidade Óssea/fisiologia , Fraturas do Colo Femoral/diagnóstico por imagem , Cabeça do Fêmur/patologia , Fraturas por Osteoporose/diagnóstico por imagem , Absorciometria de Fóton , Idoso , Idoso de 80 Anos ou mais , Estudos Transversais , Feminino , Fraturas do Colo Femoral/fisiopatologia , Humanos , Masculino , Fraturas por Osteoporose/fisiopatologia , Microtomografia por Raio-XRESUMO
INTRODUCTION: Evidence from the adult population suggests that sleep-disordered breathing (SDB) (i.e., obstructive sleep apnea [OSA]) is negatively associated with bone mineral density. Whether a similar association exists in children with SDB has not been investigated. Using the mandibular cortical width (MCW) as a proxy for skeletal bone density, we investigated if children at risk of SDB or diagnosed with OSA have a reduced mandibular cortical width compared to children without SDB. METHODS: Two retrospective cross-sectional studies were performed. The first study included comparison of MCW between 24 children with polysomnographically (PSG) diagnosed OSA and 72 age- and sex-matched control children. The second study included a cohort of children in which SDB was suggested by the Pediatric Sleep Questionnaire (PSQ) ( n = 101). MCW was measured from panoramic radiographs. RESULTS: Multiple-predictors regression analysis from the first study indicated that in children with a severe form of SDB, as induced by OSA severity, there was a negative association with MCW (ß = -0.290, P = 0.049). Moreover, PSG-diagnosed OSA children had thinner MCW (2.9. ± 0.6mm) compared to healthy children (3.5 ± 0.6 mm; P = 0.002). These findings were further supported by the second study illustrating that PSQ total scores were negatively associated with MCW (ß = -0.391, P < 0.001). CONCLUSIONS: Findings suggest that children at risk for or diagnosed with SDB exhibit reduced mandibular cortical width that purportedly may reflect alterations in bone homeostasis. KNOWLEDGE TRANSFER STATEMENT: We report that sleep-disordered breathing (including its severe form, obstructive sleep apnea) in children is associated with reduced mandibular cortical width. This association might be a direct consequence of reduced bone health to sleep-disordered breathing or a reflection that reduced bone formation underlies the development of sleep-disordered breathing. Our findings suggest that mandibular cortical width can be used as an adjunct diagnostic parameter for the diagnosis of sleep-disordered breathing.
Assuntos
Síndromes da Apneia do Sono , Apneia Obstrutiva do Sono , Adulto , Criança , Estudos Transversais , Humanos , Estudos Retrospectivos , SonoRESUMO
OBJECTIVES: Susceptibility artefacts from dental materials may compromise MRI diagnosis. However, little is known regarding MRI artefacts of dental material samples with the clinical shapes used in dentistry. The present phantom study aims to clarify how pulse sequences and sequence parameters affect MRI artefacts caused by metal-ceramic restorations. METHODS: A phantom consisting of nickel-chromium metal-ceramic restorations (i.e. dental crowns and fixed bridges) and cylindrical reference specimens immersed in agar gel was imaged in 1.5 and 3.0 T MRI scanners. Gradient echo (GRE), spin echo (SE) and ultrashort echo time (UTE) pulse sequences were used. The artefact area in each image was automatically calculated from the pixel values within a region of interest. Mean values for similar pulse sequences differing in one parameter at a time were compared. A comparison between mean artefact area at 1.5 and 3.0 T, and from GRE and SE was also carried out. In addition, a parametric correlation between echo time (TE) and artefact area was performed. RESULTS: A significant correlation was found between TE and artefact area in GRE images. Higher receiver bandwidth significantly reduced artefact area in SE images. UTE images yielded the smallest artefact area at 1.5 T. In addition, a significant difference in mean artefact area was found between images at 1.5 and 3.0 T field strengths (p = 0.028) and between images from GRE and SE pulse sequences (p = 0.005). CONCLUSIONS: It is possible to compensate the effect of higher field strength on MRI artefacts by setting optimized pulse sequences for scanning patients with metal-ceramic restorations.
Assuntos
Artefatos , Ligas de Cromo/química , Porcelana Dentária/química , Imageamento por Ressonância Magnética/métodos , Ligas Metalo-Cerâmicas/química , Coroas , Prótese Parcial Fixa , Humanos , Campos Magnéticos , Imagens de FantasmasRESUMO
Immediate dental implant placement in the molar region is critical, because of the high amount of bone loss and the discrepancy between alveolar crest thickness and the implant platform. Laser phototherapy (LPT) improves bone repair. The aim of this study was to evaluate the human alveolar bone repair 40 days after molar extraction in patients submitted to LPT. Twenty patients were selected for this randomized controlled clinical trial; 10 underwent LPT (laser group) with a GaAlAs diode laser (808 nm, 100 mW, 0.04 cm(2), 75 J/cm(2), 30s per point, 3 J per point, at five points). The control group patients (n=10) were not irradiated. Forty days later, the tissue formed inside the sockets was analyzed by micro-computed tomography and histomorphometry. Data from the two groups were compared with Student's t-test and Pearson's correlation test. The relative bone volume was significantly higher in the laser group (P<0.0001). The control group showed negative correlations (P<0.01) between number and thickness, and between number and separation of trabeculae, and a positive correlation between thickness and separation of trabeculae. The laser group showed a significant negative correlation between the number and thickness of trabeculae (P<0.01). The results suggest that LPT is able to accelerate alveolar bone repair after molar extraction, leading to a more homogeneous trabecular configuration represented by thin and close trabeculae.