Graphene oxide decreases the effects of salt stress on Persian clover seed germination.

Among biotic and abiotic stresses, the most restrictive for plant distribution is salt stress, where different concentrations might exert harmful effects on seed germination. Recently, nanomaterials were used successfully to mitigate these stresses, indicating that plants may be able to develop normally in adverse conditions. The aim of this study was to examine the effects of graphene oxide (GO) on the germination of Persian clover seedlings under salt stress conditions. Following sown on substrate paper, seeds were tested after exposure to different concentrations of graphene oxide (0, 125, 250, or 500 mg L-1 GO), sodium chloride (0; -0.1; -0.2; -0.3, or -0.4 MPa NaCl) and/or GO + salt concomitantly, and then stored for 7 days in a germination chamber at 20°C in the presence of light. Seed germination and growth parameters of seedlings were determined. Graphene oxide demonstrated protective effect against salt stress as evident by no marked adverse effects on seed germination where GO blocked the salt-induced reduction in germination. The results obtained provide references for the safe application of nanomaterials and emphasize the significance of GO as a promising material for reducing the toxicity of salts in agriculture.

Magnetic graphene derivates for efficient herbicide removal from aqueous solution through adsorption.

2,4-Dichlorophenoxyacetic acid (2,4-D) is an herbicide and is among the most widely distributed pollutant in the environment and wastewater. Herein is presented a complete comparison of adsorption performance between two different magnetic carbon nanomaterials: graphene oxide (GO) and its reduced form (rGO). Magnetic functionalization was performed employing a coprecipitation method, using only one source of Fe2+, requiring low energy, and potentially allowing the control of the amount of incorporated magnetite. For the first time in literature, a green reduction approach for GO with and without Fe3O4, maintaining the magnetic behavior after the reaction, and an adsorption performance comparison between both carbon nanomaterials are demonstrated. The nanoadsorbents were characterized by FTIR, XRD, Raman, VSM, XPS, and SEM analyses, which demonstrates the successful synthesis of graphene derivate, with different amounts of incorporate magnetite, resulting in distinct magnetization values. The reduction was confirmed by XPS and FTIR techniques. The type of adsorbent reveals that the amount of magnetite on nanomaterial surfaces has significant influence on adsorption capacity and removal efficiency. The procedure demonstrated that the best performance, for magnetic nanocomposites, was obtained by GO∙Fe3O4 1:1 and rGO∙Fe3O4 1:1, presenting values of removal percentage of 70.49 and 91.19%, respectively. The highest adsorption capacity was reached at pH 2.0 for GO∙Fe3O4 1:1 (69.98 mg g-1) and rGO∙Fe3O4 1:1 (89.27 mg g-1), through different interactions: π-π, cation-π, and hydrogen bonds. The adsorption phenomenon exhibited a high dependence on pH, initial concentration of adsorbate, and coexisting ions. Sips and PSO models demonstrate the best adjustment for experimental data, suggesting a heterogeneous surface and different energy sites, respectively. The thermodynamic parameters showed that the process was spontaneous and exothermic. Finally, the nanoadsorbents demonstrated a high efficiency in 2,4-D adsorption even after five adsorption/desorption cycles.

Study of phenobarbital removal from the aqueous solutions employing magnetite-functionalized chitosan.

Due to its wide use in anticonvulsant pharmacotherapy, phenobarbital (PHEN) is an aquatic contaminant with a high prevalence in the environment. In this adsorption study, chitosan and chitosan-based magnetic adsorbents containing different amounts of incorporated magnetite (CS, CS·Fe3O4 1:1, CS·Fe3O4 1:5, and CS·Fe3O4 1:10) were used for phenobarbital removal. The magnetic adsorbents were synthesized by co-precipitation method and characterized through FTIR, XRD, MEV, and VSM analysis. In PHEN adsorption, the equilibrium and adsorption kinetic were better adjusted by the Sips and pseudo-second-order model, respectively. Among the four nanoadsorbents used, the maximum phenobarbital adsorption capacity was 94.60 mg g-1 using 25 mg of CS·Fe3O4 1:5, with a concentration of PHEN (50 mg L-1), pH 7.0 at room temperature. The parameters of pH, adsorbent dosage, ionic strength, and thermodynamic study were tested for the adsorbent with the highest performance (CS·Fe3O4 1:5). The nanoadsorbent demonstrates efficiency in the removal of the contaminant for diverse adsorption cycles. Finally, the protocol employing magnetic adsorbents dispenses the subsequent steps of filtration and centrifugation.

An Overview of Renal Cell Carcinoma Hallmarks, Drug Resistance, and Adjuvant Therapies.

Renal neoplasms are highlighted as one of the 10 most common types of cancer. Renal cell carcinoma (RCC) is the most common type of renal cancer, considered the seventh most common type of cancer in the Western world. The most frequently altered genes described as altered are VHL, PBRM1, SETD2, KDM5C, PTEN, BAP1, mTOR, TP53, TCEB1 (ELOC), SMARCA4, ARID1A, and PIK3CA. RCC therapies can be classified in three groups: monoclonal antibodies, tyrosine kinase inhibitors, and mTOR inhibitors. Besides, there are targeted agents to treat RCC. However, frequently patients present side effects and resistance. Even though many multidrug resistance mechanisms already have been reported to RCC, studies focused on revealing new biomarkers as well as more effective antitumor therapies with no or low side effects are very important. Some studies reported that natural products, such as honey, epigallocatechin-3-gallate (EGCG), curcumin, resveratrol, and englerin A showed antitumor activity against RCC. Moreover, nanoscience is another strategy to improve RCC treatment and reduce the side effects due to the improvement in pharmacokinetics and reduction of toxicities of chemotherapies. Taking this into account, we conducted a systemic review of recent research findings on RCC hallmarks, drug resistance, and adjuvant therapies. In conclusion, a range of studies reported that RCC is characterized by high incidence and increased mortality rates because of the development of resistance to standard therapies. Given the importance of improving RCC treatment and reducing adverse effects, nanoscience and natural products can be included in therapeutic strategies.

Highly Efficient Adsorption of Tetracycline Using Chitosan-Based Magnetic Adsorbent.

Herein, tetracycline adsorption employing magnetic chitosan (CS·Fe3O4) as the adsorbent is reported. The magnetic adsorbent was synthesized by the co-precipitation method and characterized through FTIR, XRD, SEM, and VSM analyses. The experimental data showed that the highest maximum adsorption capacity was reached at pH 7.0 (211.21 mg g-1). The efficiency of the magnetic adsorbent in tetracycline removal was dependent on the pH, initial concentration of adsorbate, and the adsorbent dosage. Additionally, the ionic strength showed a significant effect on the process. The equilibrium and kinetics studies demonstrate that Sips and Elovich models showed the best adjustment for experimental data, suggesting that the adsorption occurs in a heterogeneous surface and predominantly by chemical mechanisms. The experimental results suggest that tetracycline adsorption is mainly governed by the hydrogen bonds and cation-π interactions due to its pH dependence as well as the enhancement in the removal efficiency with the magnetite incorporation on the chitosan surface, respectively. Thermodynamic parameters indicate a spontaneous and exothermic process. Finally, magnetic chitosan proves to be efficient in TC removal even after several adsorption/desorption cycles.