Exploring cyclic olefin copolymer (COC) for flexible silver nanowire electrode.

The development of flexible electronic devices has been a primary focus in various fields, and silver nanowire (Ag NW) networks show significant promise due to their unique electrical and mechanical properties. However, achieving well-defined and stable nanowire coatings on polymer substrates remains challenging. This work presents a novel and simple approach for directly coating Ag NWs on cyclic olefin copolymer (COC) substrates utilizing ultraviolet/ozone (UVO) treatment, a method not previously demonstrated for this specific material system up to our knowledge. The compatibility of this approach with COC eliminates the need for complex pre- and post-treatment processes, making it a more straightforward and environmentally friendly way to improve adhesion between Ag NWs and COC. The Ag NWs/COC electrodes exhibited excellent optoelectrical performance, with a high optical transmittance of 84% and a low sheet resistance of 13 Ω/sq-metrics that compare favorably to industry standards for transparent conductive films. Additionally, the Ag NWs/COC electrodes displayed excellent mechanical stability, showing no changes in sheet resistance after both tape adhesion and film bending tests. The novelty of the presented Ag NW-COC system, combined with the simplicity and environmental benefits of the UVO coating approach, as well as the demonstrated performance and stability of the resulting electrodes, make this work a significant advancement towards realizing the commercial potential of flexible electronics for biocompatible and wearable device applications.

A surface treatment method for improving the attachment of PDMS: acoustofluidics as a case study.

A method for a permanent surface modification of polydimethylsiloxane (PDMS) is presented. A case study on the attachment of PDMS and the lithium niobate (LiNbO3) wafer for acoustofluidics applications is presented as well. The method includes a protocol for chemically treating the surface of PDMS to strengthen its bond with the LiNbO3 surface. The PDMS surface is modified using the 3-(trimethoxysilyl) propyl methacrylate (TMSPMA) silane reagent. The effect of silane treatment on the hydrophilicity, morphology, adhesion strength to LiNbO3, and surface energy of PDMS is investigated. The results demonstrated that the silane treatment permanently increases the hydrophilicity of PDMS and significantly alters its morphology. The bonding strength between PDMS and LiNbO3increased with the duration of the silane treatment, reaching a maximum of approximately 500 kPa. To illustrate the effectiveness of this method, an acoustofluidic device was tested, and the device demonstrated very promising enhanced bonding and sealing capabilities with particle manipulation at a flow rate of up to 1 L/h by means of traveling surface acoustic waves (TSAW). The device was reused multiple times with no fluid leakage or detachment issues. The utility of the presented PDMS surface modification method is not limited to acoustofluidics applications; it has the potential to be further investigated for applications in various scientific fields in the future.

Tuning the Surface Wettability of Cyclic Olefin Copolymer by Plasma Treatment and Graphene Oxide Deposition and Reduction.

Selective altering of surface wettability in microfluidic channels provides a suitable platform for a large range of processes, such as the phase separation of multiphase systems, synthesis of reaction controlled, nanoliter sized droplet reactors, and catalyst impregnation. Herein we study the feasibility to tune the wettability of a flexible cyclic olefin copolymer (COC). Two methods were considered for enhancing the surface hydrophilicity. The first is argon/oxygen plasma treatment, where the effect of treatment duration on water contact angle and COC surface morphology and chemistry were investigated, and the second is coating COC with GO dispersions of different concentrations. For enhancing the hydrophobicity of GO-coated COC surfaces, three reduction methods were considered: chemical reduction by Hydroiodic acid (HI), thermal reduction, and photo reduction by exposure of GO-coated COC to UV light. The results show that as the GO concentration and plasma treatment duration increased, a significant decrease in contact angle was observed, which confirmed the ability to enhance the wettability of the COC surface. The increase in hydrophilicity during plasma treatment was associated with the increase in surface roughness on the treated surfaces, while the increase during GO coating was associated with introducing oxygen-containing groups on the GO-coated COC surfaces. The results also show that the different reduction methods considered can increase the contact angle and improve the hydrophobicity of a GO-coated COC surface. It was found that the significant improvement in hydrophobicity was related to the reduction of oxygen-containing groups on the GO-coated COC modified surface.