Synthesis and physicochemical characterization of room temperature ionic liquids and their application in sodium ion batteries.

Sodium ion batteries (SIBs) based on IL electrolytes have attracted great attention, particularly in large-scale energy storage systems for renewable energy due to the abundance of sodium and the excellent safety resulting from the use of non-flammable ionic liquid (IL) electrolytes. In this article, a series of 15 functionalized room temperature ionic liquids (RTILs) suitable as electrolytes is presented. Special emphasis was laid on the purity of the synthesized RTILs and a consistent and uniform characterization of their physicochemical properties. Evaluation of the viscosity, conductivity, and thermal and electrochemical stabilities resulted in clear structure-property relationships, rendering the ether functionalized RTILs most promising for application in SIBs. Electrochemical investigations of the ether functionalized IL electrolytes in SIB half cells (Na0.6Mn0.9Co0.1O2 as cathode material) proved their compatibility with a SIB system. Stable cycling performance was achieved with the piperidinium based RTIL IL 6 outperforming the organic electrolyte by far with a retention of 81% after 350 cycles. These results show the suitability of RTILs to enhance the performance of SIB systems and serve as a basis for the design of high performance IL electrolytes.

Assessment of the Accuracy of Using ICD-10 Codes to Identify Systemic Sclerosis.

IMPORTANCE: With the increased use of data from electronic medical records for research, it is important to validate in-patient electronic health records/hospital electronic health records for specific diseases identification using International Classification of Diseases, Tenth Revision (ICD-10) codes. OBJECTIVE: To assess the accuracy of using ICD-10 codes to identify systemic sclerosis (SSc) in the French hospital database. DESIGN SETTING AND PARTICIPANTS: Electronic health record database analysis. The setting of the study's in-patient database was the Toulouse University Hospital, a tertiary referral center (2880 beds) that serves approximately 2.9 million inhabitants. Participants were patients with ICD-10 discharge diagnosis codes of SSc seen at Toulouse University Hospital between January 1, 2010, and December 31, 2017. MAIN OUTCOMES AND MEASURES: The main outcome was the positive predictive value (PPV) of discharge diagnosis codes for identifying SSc. The PPVs were calculated by determining the ratio of the confirmed cases found by medical record review to the total number of cases identified by ICD-10 code. RESULTS: Of the 2766 hospital stays, 216 patients were identified by an SSc discharge diagnosis code. Two hundred were confirmed as SSc after medical record review. The overall PPV was 93% (95% CI, 88-95%). The PPV for limited cutaneous SSc was 95% (95% CI, 85-98%). CONCLUSIONS AND RELEVANCE: Our results suggest that using ICD-10 codes alone to capture SSc is reliable in The French hospital database.

Electronic and Geometric Structures of Rechargeable Lithium Manganese Sulfate Li2Mn(SO4)2 Cathode.

Here, we report the use of Li2Mn(SO4)2 as a potential energy storage material and describe its route of synthesis and structural characterization over one electrochemical cycle. Li2Mn(SO4)2 is synthesized by ball milling of MnSO4·H2O and Li2SO4·H2O and characterized using a suite of techniques, in particular, ex situ X-ray diffraction, X-ray photoelectron spectroscopy, and X-ray absorption spectroscopy on the Mn and S K-edges to investigate the electronic and local geometry around the absorbing atoms. The prepared Li2Mn(SO4)2 electrodes undergo electrochemical cycles to different potential points on the charge-discharge curve and are then extracted from the cells at these points for ex situ structural analysis. Analysis of X-ray absorption spectroscopy (both near and fine structure part of the data) data suggests that there are minimal changes to the oxidation state of Mn and S ions during charge-discharge cycles. However, X-ray photoelectron spectroscopy analysis suggests that there are changes in the oxidation state of Mn, which appears to be different from the conclusion drawn from X-ray absorption spectroscopy. This difference in results during cycling can thus be attributed to electrochemical reactions being dominant at the surface of the Li2Mn(SO4)2 particles rather than in the bulk.

Effect of Conducting Salts in Ionic Liquid Electrolytes for Enhanced Cyclability of Sodium-Ion Batteries.

The electrochemical performance of ionic liquid electrolytes containing different sodium salts dissolved in 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide (BMPTFSI) evaluated in a half-cell configuration using spherical P2-Na0.6Co0.1Mn0.9O2+z (NCO) cathodes are reported. Among the various electrolytes investigated, sodium bis(fluorosulfonyl)imide (NaFSI) (0.5 M) in BMPTFSI shows the best electrochemical performance with a significant improvement in cycling stability (90% capacity retention after 500 cycles at 50 mA g-1 in a half cell versus Na metal anode) compared with conventional NaClO4 (1 M) in ethylene carbonate/propylene carbonate electrolytes (39% retention after 500 cycles). Cyclic voltammetry (CV) studies reveal that ionic liquid electrolytes are stable up to 4.8 V versus Na/Na+. When NaFSI and NaTFSI are used as conducting salts, X-ray photoelectron spectroscopy results prove that the cathode electrolyte interface (CEI) is composed of components resulting from the decomposition of the TFSI anion and the deposition of the BMP cation. On the other hand, the CEI layer of the electrode cycled in an electrolyte containing NaClO4 in BMPTFSI follows a different pathway of TFSI decomposition and consists mainly of sodium fluoride. Similarly, plating studies were used to understand the stability of different ionic liquids in contact with metallic sodium. It was found that the excellent capacity retention for the electrolyte consisting of NaFSI salt is related to the formation of a stable CEI and solid electrolyte interphase layers.