Tunable beam shaping with a phased array acousto-optic modulator.

We demonstrate the generation of Bessel beams using an acousto-optic array based on a liquid filled cavity surrounded by a cylindrical multi-element ultrasound transducer array. Conversion of a Gaussian laser mode into a Bessel beam with tunable order and position is shown. Also higher-order Bessel beams up to the fourth order are successfully generated with experimental results very closely matching simulations.

Patterning of microspheres and microbubbles in an acoustic tweezers.

We describe the construction of an ultrasonic device capable of micro-patterning a range of microscopic particles for bioengineering applications such as targeted drug delivery. The device is formed from seven ultrasonic transducers positioned around a heptagonal cavity. By exciting two or three transducers simultaneously, lines or hexagonal shapes can be formed with microspheres, emulsions and microbubbles. Furthermore, phase control of the transducers allows patterning at any desired position in a controlled manner. The paper discusses in detail direct positioning of functionalised microspheres, emulsions and microbubbles. With the advantages of miniaturization, rapid and simple fabrication, ultrasonic tweezers is a potentially useful tool in many biomedical applications.

Acoustic radiation force analysis using finite difference time domain method.

Acoustic radiation force exerted by standing waves on particles is analyzed using a finite difference time domain Lagrangian method. This method allows the acoustic radiation force to be obtained directly from the solution of nonlinear fluid equations, without any assumptions on size or geometry of the particles, boundary conditions, or acoustic field amplitude. The model converges to analytical results in the limit of small particle radii and low field amplitudes, where assumptions within the analytical models apply. Good agreement with analytical and numerical models based on solutions of linear scattering problems is observed for compressible particles, whereas some disagreement is detected when the compressibility of the particles decreases.

Manipulation of microparticles using phase-controllable ultrasonic standing waves.

A method of manipulating microparticles in a liquid using ultrasound is proposed and demonstrated. An ultrasonic standing wave with nodal planes whose positions are controllable by varying the relative phase of two applied sinusoidal signals is generated using a pair of acoustically matched piezoelectric transducers. The resulting acoustic radiation force is used to trap micron scale particles at a series of arbitrary positions (determined by the relative phase) and then move them in a controlled manner. This method is demonstrated experimentally and 5 µm polystyrene particles are trapped and moved in one dimension through 140 µm.

Ultrasonic defect characterization using parametric-manifold mapping.

The aim of ultrasonic non-destructive evaluation includes the detection and characterization of defects, and an understanding of the nature of defects is essential for the assessment of structural integrity in safety critical systems. In general, the defect characterization challenge involves an estimation of defect parameters from measured data. In this paper, we explore the extent to which defects can be characterized by their ultrasonic scattering behaviour. Given a number of ultrasonic measurements, we show that characterization information can be extracted by projecting the measurement onto a parametric manifold in principal component space. We show that this manifold represents the entirety of the characterization information available from far-field harmonic ultrasound. We seek to understand the nature of this information and hence provide definitive statements on the defect characterization performance that is, in principle, extractable from typical measurement scenarios. In experiments, the characterization problem of surface-breaking cracks and the more general problem of elliptical voids are studied, and a good agreement is achieved between the actual parameter values and the characterization results. The nature of the parametric manifold enables us to explain and quantify why some defects are relatively easy to characterize, whereas others are inherently challenging.

The detectability of kissing bonds in adhesive joints using ultrasonic techniques.

This paper concerns a study of the detectability of dry contact kissing bonds in adhesive joints using three ultrasonic inspection techniques. Conventional normal incidence longitudinal and shear wave inspection were conducted on dry contact kissing bonds using a standard damped ultrasonic transducer and an electro-magnetic acoustic transducer (EMAT) respectively. The detectability of the dry contact kissing bonds was assessed by calculating the reflection coefficient of the imperfect interface at varying loads for a number of surface roughnesses. A high power ultrasonic method was also employed to determine the non-linear behavior of the adhesive interface. The non-linearity of the interface was determined by the ratio of the amplitudes of the first harmonic and fundamental frequencies of the transmitted waveform. It was found that the high power technique showed the greatest sensitivity to these kissing bonds at low contact pressures, however at high loads conventional longitudinal wave testing was more sensitive. It was also noted that a combination of two or more techniques could provide enhanced information about the kissing bond compared to a single technique alone.

Ultrasonic assembly of anisotropic short fibre reinforced composites.

We report the successful manufacture of short fibre reinforced polymer composites via the process of ultrasonic assembly. An ultrasonic device is developed allowing the manufacture of thin layers of anisotropic composite material. Strands of unidirectional reinforcement are, in response to the acoustic radiation force, shown to form inside various matrix media. The technique proves suitable for both photo-initiator and temperature controlled polymerisation mechanisms. A series of glass fibre reinforced composite samples constructed in this way are subjected to tensile loading and the stress-strain response is characterised. Structural anisotropy is clearly demonstrated, together with a 43% difference in failure stress between principal directions. The average stiffnesses of samples strained along the direction of fibre reinforcement and transversely across it were 17.66±0.63MPa and 16.36±0.48MPa, respectively.

Comparison of ultrasonic array imaging algorithms for nondestructive evaluation.

Ultrasonic array imaging algorithms have been widely used and developed in nondestructive evaluation in the last 10 years. In this paper, three imaging algorithms [total focusing method (TFM), phase-coherent imaging (PCI), and spatial compounding imaging (SCI)] are compared through both simulation and experimental measurements. In the simulation, array data sets were generated using a hybrid forward model containing a single defect among a multitude of randomly distributed point scatterers to represent backscatter from material microstructure. The number of point scatterers per unit area and their scattering amplitude were optimized to reduce computation cost. The SNR of the final images and their resolution were used to indicate the quality of the different imaging algorithms. The images of different types of defects (point reflectors and planar cracks) were used to investigate the robustness of the imaging algorithms. It is shown that PCI can yield higher image resolution and higher SNR for defects in material with weak backscatter than TFM, but that the images of cracks are distorted. Overall, TFM is the most robust algorithm across a range of different types of defects. It is also shown that the detection limit of all three imaging algorithms is almost equal for weakly scattering defects.