A preliminary study on the properties and fouling-release performance of siloxane-polyurethane coatings prepared from poly(dimethylsiloxane) (PDMS) macromers.

Siloxane-polyurethane fouling-release (FR) coatings based on aminopropyl terminated poly(dimethylsiloxane) (PDMS) macromers were prepared and characterized for FR performance via laboratory biological assays. These systems rely on self-stratification, resulting in a coating with a siloxane-rich surface and polyurethane bulk. Previously, these coating systems have used PDMS with multiple functional groups which react into the polyurethane bulk. Here, aminopropyl terminated PDMS macromers were prepared, where a single amine group anchors the PDMS in the coating. Coatings were prepared with four molecular weights (1000, 5000, 10,000, and 15,000 g mol⁻¹) and two levels of PDMS (5% and 10%). High water contact angles and low surface energies were observed for the coatings before and after water immersion, along with low pseudobarnacle removal forces. Laboratory bioassays showed reduced biofilm retention of marine bacteria, good removal of diatoms from coatings with low molecular weight PDMS, high removal of algal sporelings (young plants), and low removal forces of live barnacles.

Combinatorial and high-throughput screening of the effect of siloxane composition on the surface properties of crosslinked siloxane-polyurethane coatings.

Libraries of siloxane-polyurethane coatings were designed, formulated, and screened using high-throughput experimentation. Four independent variables that were analyzed were the molecular weight of poly(dimethylsiloxane) (PDMS), presence or absence of poly(epsilon-caprolactone) (PCL) blocks attached to the PDMS backbone, the length of the PCL blocks, and the siloxane polymer level in the coating formulations. In addition to the siloxane libraries (3-aminopropyl-terminated PDMS and poly(epsilon-caprolactone)-poly(dimethylsiloxane)-poly(epsilon-caprolactone) (PCL-PDMS-PCL) triblock copolymers), the coating formulation included a trifunctional isocyanate crosslinker, trifunctional poly(epsilon-caprolactone) polyol, 2,4-pentanedione (pot-life extender), dibutyltin diacetate (catalyst), and a blend of solvents. The resulting coatings were analyzed for their surface energy and pseudobarnacle adhesion both before and after aging the coatings for 30 days in water. The water and methylene iodide contact angle averages increase with increasing molecular weight of PDMS. Coatings prepared from PCL-PDMS-PCL triblock copolymers have lower surface energies than coatings prepared from 3-aminopropyl-terminated PDMS; however, lower pseudobarnacle adhesion results were obtained for the coatings prepared from 3-aminopropyl-terminated PDMS than coatings prepared from PCL-PDMS-PCL triblock copolymers. The siloxane polymer level in the coating formulations does not have a significant effect on the surface energy of the coatings, but it resulted in higher pseudobarnacle adhesion.

Laboratory screening of coating libraries for algal adhesion.

Coatings libraries achieved through a combinatorial chemistry approach, which may generate tens to hundreds of formulations, can be deposited in an array of 12 patches, each approximately 9 cm(2), on 10 x 20 cm primed aluminum panels. However, existing methods to quantify algal biomass on coatings are unsuitable for this type of array format. This paper describes an algorithm modelled on a probability distribution that quantifies the area of surface covered by a green alga from digital images. The method allows coatings with potential fouling-release properties to be down-selected for further evaluation. The use of the algorithm is illustrated by a set of eight siloxane-polyurethane coatings made using organofunctional poly(dimethylsiloxane) (PDMS) and poly(epsilon-caprolactone)-PDMS-poly(epsilon-caprolactone) (PCL-PDMS-PCL) triblock copolymers along with four PDMS standards which were deposited on one panel. Six replicate panels were seeded with Ulva zoospores which grew into sporelings (small plants) that completely covered the surface. The ease of removal of the Ulva sporeling biofilms was determined by automated water jetting at six different impact pressures. The coverage of the biofilm on the twelve individual formulations after jet washing was quantified from the green colour of digital images. The data are discussed in relation to the composition of the coatings.

Combinatorial materials research applied to the development of new surface coatings IV. A high-throughput bacterial biofilm retention and retraction assay for screening fouling-release performance of coatings.

A high-throughput bacterial biofilm retention screening method has been augmented to facilitate the rapid analysis and down-selection of fouling-release coatings for identification of promising candidates. Coatings were cast in modified 24-well tissue culture plates and inoculated with the marine bacterium Cytophaga lytica for attachment and biofilm growth. Biofilms retained after rinsing with deionised water were dried at ambient laboratory conditions. During the drying process, retained biofilms retracted through a surface de-wetting phenomenon on the hydrophobic silicone surfaces. The retracted biofilms were stained with crystal violet, imaged, and analysed for percentage coverage. Two sets of experimental fouling-release coatings were analysed with the high-throughput biofilm retention and retraction assay (HTBRRA). The first set consisted of a series of model polysiloxane coatings that were systematically varied with respect to ratios of low and high MW silanol-terminated PDMS, level of cross-linker, and amount of silicone oil. The second set consisted of cross-linked PDMS-polyurethane coatings varied with respect to the MW of the PDMS and end group functionality. For the model polysiloxane coatings, HTBRRA results were compared to data obtained from field immersion testing at the Indian River Lagoon at the Florida Institute of Technology. The percentage coverage calculations of retracted biofilms correlated well to barnacle adhesion strength in the field (R(2)=0.82) and accurately identified the best and poorest performing coating compositions. For the cross-linked PDMS-polyurethane coatings, the HTBRRA results were compared to combinatorial pseudobarnacle pull-off adhesion data and good agreement in performance was observed. Details of the developed assay and its implications in the rapid discovery of new fouling-release coatings are discussed.