Phragmites australis (Reed) as an Efficient, Eco-Friendly Adsorbent for Brackish Water Pre-Treatment in Reverse Osmosis: A Kinetic Study.

A cost-effective adsorbent was prepared by carbonization of pre-treated Phragmites australis reed at 500 °C. Phragmites australis was characterized using Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), and Brunauer-Emmett-Teller (BET) surface analyses. XRD of the as-prepared adsorbent exhibited a partially crystalline structure with a specific surface area of 211.6 m2/g and an average pore diameter of 4.2 nm. The biosorption potential of novel biosorbent Phragmites australis reed was investigated with a batch scale and continuous flow study. The study was conducted at different constraints to obtain optimum pH conditions, adsorbent dose, contact time, agitation speed, and initial TDS concentration. In order to analyze the properties of the procedure and determine the amount of sodium removal, Langmuir, Freundlich, and Dubinin-Radushkevich isotherms were tested. The optimal values of contact time, pH, and adsorbent dose were found to be 150 min, 4, and 10 g/L, respectively, with an agitation speed of 300 rpm at room temperature (27 °C). The three tested isotherms show that the adsorption of Na+ onto the prepared adsorbent is a hybrid process from physi- and chemisorption. For industrial application, the adsorbent was tested using the adsorbent column technique. Pseudo-first-order, pseudo-second-order, and diffusion models were connected, and it was discovered that the information fit best to the pseudo-second-arrange active model. According to the intraparticle diffusion model, the mechanism goes through four stages before reaching equilibrium. The periodicity test shows that the adsorption ability of Phragmites australis can be recovered by washing with 0.1 M HCl.

Industrial-scale feasibility for textile wastewater treatment via Photocatalysis-adsorption technology using black sand and UV lamp.

Dye-contaminated wastewater is a major environmental problem that requires effective and affordable treatment methods. This study investigates an innovative approach using black sand filtration assisted by UV light to remove methylene blue (MB) dye from wastewater. The motivation is to develop a sustainable low-cost wastewater treatment technology. Black sand's composition of iron oxide and other metal oxides enables the adsorption and photocatalytic degradation of dyes. The effects of operating parameters, including pH, bed height, flow rate, and initial MB concentration, were examined using a fixed-bed column system. The maximum adsorption capacity was 562.43 mg g-1 at optimal pH 10, 15 cm bed height, 50 ppm MB, and 53.33 mL min-1 flow rate. Mathematical models effectively described the experimental breakthrough curves. For real textile wastewater, black sand with a UV lamp removed 50.40% COD, 73.68% TDS, 43.82% TSS, and 98.57% conductivity, significantly outperforming filtration without UV assistance. Characterization via XRD, XRF, FTIR, zeta potential, and SEM revealed black sand's photocatalytic properties and mechanism of MB adsorption. The findings demonstrate black sand filtration plus UV irradiation as a feasible, sustainable technology for removing dyes and organics from wastewater. This method has promise for the scale-up treatment of textiles and other industrial effluents.

Synergistic effects (adsorption and biodegradation) of Streptomyces hydrogenans immobilization on nano-reed biochar for further application in upflow anaerobic sludge blanket.

Water pollution due to wastewater is a serious issue that needs to be studied as many organic compounds are released from wastewater, affecting the ecosystem. Therefore, appropriate treatment methods should be used to prevent these effects. Phragmites australis biochar immobilized with bacteria was prepared in this study for use as an adsorbent in a pilot-scale up-flow anaerobic sludge blanket (UASB) to remove organic matter from wastewater in a buffalo farm. Combining reed biochar and immobilized Streptomyces hydrogenans introduces a synergistic effect: reed biochar serves as a substrate for microbial colonization and provides a conducive environment for microbial growth while Streptomyces hydrogenans, immobilized on the biochar, enhances the degradation of organic matter through its metabolic activities. Suitable techniques were employed, including infrared spectroscopy (FTIR) to determine the functional groups before and after adsorption, scanning electron microscopy (SEM) to determine the morphology of the composite before and after adsorption, X-ray diffraction (XRD) to examine the mineralogical changes through reflectometry, high-resolution diffraction and Brunauer-Emmett-Teller (BET) analyses to determine the surface area that always carried out by nitrogen adsorption/desorption technique based on the BET isotherm. Two-level factorial design experiments optimized using biochar, immobilized with bacteria, were employed to enhance the UASB performance. Chemical oxygen demand (COD) removal and biogas production were studied as a function of four experimental parameters: biochar dose, buffalo sludge dose, pH, and bacteria type. The buffalo sludge (manure) dose negatively affected the model's performance. The results showed better COD removal with Streptomyces hydrogenans S11 inoculation. The optimum biochar dose, buffalo sludge dose, and pH were 20 g L-1, 0%, and 7.5, respectively. The COD removal efficiency under these experimental conditions reached 92.70% with a biogas production of 5.0 mL. The experimental results of a validated point from the model were 90.80% for COD removal ratio and 4.80 mL for biogas production at 2 g L-1 biochar dose, 0% buffalo sludge dose, and pH 7.5 using Streptomyces hydrogenans S11 bacteria. A buffalo wastewater (BWW) anaerobic digestion experimental model was best fitted to the data under optimal conditions. This study aligns with the United Nations Sustainable Development Goals (SDGs), specifically SDG 6 (clean water and sanitation) and SDG 12 (responsible consumption and production). The implications of our work extend to large-scale applications, promising a greener and more sustainable future for wastewater treatment.

Adsorption of Mn(ii) ions from wastewater using an AgNPs/GO/chitosan nanocomposite material.

Water contaminated with heavy metal ions is extremely poisonous and threatens living organisms. Therefore, scientists place a premium on removing heavy metal ions from water that has already been contaminated. Removing metal ions from water typically involves the use of nanomaterials. Chitosan was made by extracting it from shrimp shells and combining it with a 3 : 1 ratio of synthetically produced AgNPs/GO. Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) with transmission electron microscopy (TEM), and X-ray diffraction were used to investigate an AgNPs/GO/chitosan nanocomposite (XRD). A number of studies must be run to determine the optimal pH, adsorbent quantity, retention period, stirring speed, temperature, and initial concentration. The studies were conducted in a variety of ways. The isotherms of Langmuir, Freundlich, and Dubinin-Radushkevich were utilized. The industrial wastewater was used in the column adsorption experiment, and the flow rates and column bed heights were varied. An optimum contact time, pH, and adsorbent dosage for Mn(ii) were determined. At 30 minutes, pH 6, and 0.05 grams of Mn(ii) adsorbent per 100 ml, with agitation at 250 rpm, room temperature of 30 °C, and an initial concentration of 40 ppm, the best conditions were discovered. A positive correlation coefficient finding (R 2 = 0.925) indicates a good fit for Mn, according to equilibrium studies (II). The pseudo-second-order active model was connected to data that suited the pseudo-first and pseudo-second-order models. In the intra-particle diffusion model, the mechanism must proceed through four phases before equilibrium is reached. In an industrial adsorbent column, the adsorbent was put to the test. The periodicity test demonstrates that the nanocomposite's adsorption capability can be recovered by washing it with 0.1 M HCl. Mn(ii) adsorbed on AgNPs/GO/Chitosan after four cycles was only 20%, insufficient for additional adsorption tests. The repeated cycles that led to the partial loss of the adsorbate may have reduced the adsorbent material's efficacy.

Fe(iii) and Cr(vi) ions' removal using AgNPs/GO/chitosan nanocomposite as an adsorbent for wastewater treatment.

Heavy metal ions in water refer to significant risks to the biological system due to their high toxicity. Therefore, the decontamination of water polluted by heavy metal ions attracts significant interest of researchers. Adsorption by nanomaterials has been a widely used technique for removing heavy metal ions from water. Chitosan was extracted from shrimp shellfish and mixed with laboratory-prepared AgNPs/GO in the ratio of 3 : 1. A series of tests evaluates the best condition of pH, amount of adsorbent, retention time, stirring speed, temp, and initial concentration. The research was conducted under various conditions. Langmuir, Freundlich, Tempkin, and Dubinin-Radushkevich isotherms were also tested. Also, the column adsorption experiment was carried out on industrial wastewater at different flow rates and column bed heights. The optimal values of the contact time, pH, and adsorbent dose of Cr(vi) were found to be 80 min, 4, and 0.1 g 100 mL-1, respectively, at room temperature (30 °C), agitation at 150 rpm, and initial concentration of 50 ppm. On the other hand, the optimal value of contact time, pH, and adsorbent dose of Fe(iii) were found to be 30 min, 6, and 0.02 g 100 mL-1, respectively, at room temp (30 °C) with a stirring speed of 250 rpm and an initial concentration of 40 ppm. For Cr(vi) and Fe(iii), equilibrium studies show that the data fit the Freundlich isotherm well (correlation coefficient, R 2 = 0.98) (III). A link between the pseudo-second order active model and data fitting the pseudo-first order active models were made. Within the intraparticle diffusion model, there are four stages that the mechanism must go through before it is at equilibrium. The adsorbent was tested in an industrial adsorbent column. This test proves that the nanocomposite's adsorption capacity can be restored by washing it with 0.1 M HCl, as shown by the periodicity test. After four cycles, the amount of Cr(vi) adsorbed on AgNPs/GO/chitosan was just 20%, which is insufficient for further adsorption experiments. Cr(vi) removal rates (%R) decreased slightly.

Synthetization and characterization of SnCaAl2O3 nanocomposite and using as a superior adsorbent for Pb, Zn, and Cd ions in polluted water.

The presence of heavy metals in drinking water or wastewater poses a serious threat to the ecosystem. Hence, the present study focused on synthesizing SnCaAl2O3 core-shell nanoparticles (C.N.P.s) in the α-Alumina phase by thermal annealing a stacked structure sandwiched between two Al2O3 layers at low temperatures. The obtained structure showed Sn N.P. floating gate with an Al2O3 dielectric stacked tunneling barrier to remove the excess of these heavy metals from polluted water. To characterize the prepared composites, X-ray diffraction (XRD), field emission scanning electron microscope (FE-SEM), and high-resolution transmission electron microscopy (HR-TEM) were used. The synthesized SnCaAl2O3 C.N.P.s composite was examined to utilize it as an adsorbent for removing Zn, Cd, and Pb divalent cations. The removal efficiency was studied by various parameters such as adsorbent dose, pH, contact time, metal concentrations, temperature, and coexisting ions. The experimental results were tested via Langmuir and Freundlich isotherm models. The obtained results were convenient to the Freundlich isotherm model. Moreover, the adsorption thermodynamic behavior of Zn+2, Cd+2, and Pb+2 on the synthesized composite was examined, and the process is endothermic and spontaneous under experimental conditions. The results illustrated that the adsorption efficiency of the SnCaAl2O3 core-shell nanoparticles (C.N.P.s) ranged from 88% to about 100% for all cations.

Enhanced Performance of Chitosan via a Novel Quaternary Magnetic Nanocomposite Chitosan/Grafted Halloysitenanotubes@ZnγFe3O4 for Uptake of Cr (III), Fe (III), and Mn (II) from Wastewater.

A novel chitosan/grafted halloysitenanotubes@Znγmagnetite quaternary nanocomposite (Ch/g-HNTs@ZnγM) was fabricated using the chemical co-precipitation method to remove the ions of Cr (III), Fe (III), and Mn (II) from wastewater. The characteristics of the synthesized Ch/g-HNTs@ZnγM quaternary nanocomposite were investigated using FTIR, SEM, XRD, GPC, TGA, TEM, and surface zeta potential. The characterization analysis proved that the mentioned nanocomposite structure contains multiple functional groups with variable efficiencies. Additionally, they proved the existence of magnetic iron in the nanocomposite internal structure with the clarity of presentation of gaps and holes of high electron density on its surface. The results showed that the pH and time to reach an equilibrium system for all the studied metal ions were obtained at 9.0 and 60 min, respectively. The synthesized Ch/g-HNTs@ZnγM nanocomposite exhibited maximum adsorption removal of 95.2%, 99.06%, and 87.1% for Cr (III), Fe (III), and Mn (II) ions, respectively. The pseudo-second-order kinetic model and, for isotherm, the Langmuir model were best fitted with the experimental data. The thermodynamic parameters indicated the exothermic and spontaneous nature of the adsorption reaction as proven by the ΔH° and ΔG° values. Additionally, chemical adsorption by the coordination bond is supposed as the main mechanism of adsorption of the mentioned metal ions on the nanocomposite. Finally, Ch/g-HNTs@ZnγM displays prospected advantages, such as a low-expense adsorbent, high efficiency and availability, and an eco-friendly source, that will reduce the environmental load via an environmentally friendly method.

Enhanced Nanofiltration Process of Thin Film Composite Membrane Using Dodecyl Phenol Ethoxylate and Oleic Acid Ethoxylate for Oilfield Calcite Scale Control.

This research studied the enhancing effect on the nanofiltration composite (TFCNF) membrane of two non-ionic surfactants on a thin-film composite nanofiltration membrane (TFCNF) for calcite scale (CaCO3) inhibition in oilfield application to develop a multifunctional filtration system: nanofiltration, antiscalant, and scale inhibitors. The effectiveness of dodecyl phenol ethoxylate (DPE) and oleic acid ethoxylate (OAE) as novel scale inhibitors were studied using the dynamic method. Scaling tests on the membrane were performed to measure the scaling of the inhibited membrane with and without scale inhibitors for salt rejection, permeability, and flux decline. The results revealed that the TFCNF membrane flux decline was improved in the presence of scale inhibitors from 22% to about 15%. The rejection of the membrane scales increases from 72% for blank membranes, reaching 97.2% and 88% for both DPE and OAE, respectively. These confirmed that scale inhibitor DPE had superior anti-scaling properties against calcite deposits on TFCNF membranes. Inhibited scaled TFCNF membrane was characterized using environmental scanning electron (ESEM), FTIR, and XRD techniques. The results of the prepared TFCNF membrane extensively scaled by the calcite deposits were correlated to its morphology.

An integrated bioaugmentation/electrocoagulation concept for olive mill wastewater management and the reuse in irrigation of biofuel plants: a pilot study.

A consortium of highly degrading microorganisms was used in an integrated bioaugmentation/electrocoagulation process for treating olive mill wastewater. The system was investigated for treating 1 m3 day-1, at a pilot scale, for 2 years; hydraulic loading rate and organic loading rate were 2880 l m-2 day-1 and 37,930 g COD m-2 day-1, respectively. Average removal efficiency for COD, oils, and total phenols was 63.9%, 85.2%, and 43.6%, respectively. The olive mill consortium, OMC, consisted of seven actinomycete strains. The strains were confirmed, by 16S rDNA analysis, to belong to five Streptomyces, one Kitasatospora, and one Micromonospora strains, at 100-99.06% similarities. Hydrolytic enzyme activities of OMC strains were remarkably higher for degrading cellulosic and lipid constituents (enzyme-cumulative indices, 14-16.1), than the phenolic constituents (indices, 4.1-6.5). The establishment of actinomycetes in the treatment system was indicated by their increased counts in the biofilm at the end of the biofilter, reaching 13-fold higher than that in the control bed. The treated effluent was toxic to the seedlings of Jatropha curcas (Jatropha) and Simmondsia chinensis (Jojoba). Though its application in irrigation of 3-year-old Jatropha shrubs, significantly, enhanced the fruit yield up to 1.85-fold higher than the control, without affecting the seed oil content, after 3-month application, the irrigated soil showed insignificant changes in its biochemical properties. This developed bioaugmentation/electrocoagulation process can treat wastewater with extremely high organic strength, while its approximate construction and operational costs are limited to 0.03 and 0.51 US$ m-3, respectively. It produces a treated effluent that can be reused in irrigation of specific plants. Graphical abstract.

Regression, kinetics and isotherm models for biosorption of organic pollutants, suspended and dissolved solids by environmentally friendly and economical dried Phragmites australis.

Low cost adsorbents such as P. australis have received considerable interest owing to their low cost and easy availability. The aim of the present study was the evaluation of the removal of chemical oxygen demand (COD), biological oxygen demand (BOD), total suspended and dissolved solids (TSS and TDS) using dried P. australis in influent wastewater to a wastewater treatment plant. The results of the COD and BOD concentration reduction with P. australis at optimum operating conditions were determined for maximum reduction and adsorption isotherms. The maximum reduction of COD, BOD, TSS and TDS concentrations under the optimum operating conditions was 92.27%, 93.89%, 94.38% and 91.61%, respectively. The results demonstrate that the new dried biosorbent is able to adsorb all the aforementioned contamination. It achieved an adsorption capacity for COD of 72.5 mg g-1 and an adsorption capacity for BOD of 43.93 mg g-1. The results were well fitted by the pseudo-second order model with R 2 = 0.984.