Hybrid Ethylcellulose Polymeric Films: Ag(I)-Based Components and Curcumin as Reinforcing Ingredients for Enhanced Food Packaging Properties.

Bio-active ethylcellulose (EC) polymeric films have been obtained by incorporating curcumin (curc) and Ag(I)-based compounds, known for their antioxidant and antimicrobial activity, respectively, within the polymeric matrix. The recently reported Ag(I) coordination polymer, in both its structural forms (α-[(bpy)Ag(OTf)]∞ and ß-{[(bpy)Ag][OTf]}∞), and the [(bpy)Ag(OTf)]∞-curc polymeric co-crystal (bpy=2,2'-bipyridine; OTf=trifluoromethanesulfonate) have been selected as Ag(I) species. The hybrid composite films have been prepared through the simple solvent casting method and characterized through Powder X-Ray Diffraction (PXRD), Differential Scanning Calorimetry (DSC) and Fourier Transform Infrared (FTIR) spectroscopy, Scanning Electron Microscope (SEM), UV-vis spectroscopy. The deep investigation of the film samples highlighted the non-inert behaviour of EC towards these specific active ingredients. Antimicrobial tests showed that EC films embedding the Ag(I)-based compounds present good antimicrobial performance, in particular against Staphylococcus aureus, used as a model of Gram-positive bacteria. In addition, Silver migration tests, performed on the Ag(I)-incorporating EC films, evidenced low values of silver release particularly in the case of the EC films incorporating [(bpy)Ag(OTf)]∞-curc.

A rapid method for the quantification of urinary phthalate monoesters: A new strategy for the assessment of the exposure to phthalate ester by solid-phase microextraction with gas chromatography and tandem mass spectrometry.

In the following work, a new method for the analysis of the phthalate monoesters in human urine was reported. Phthalate monoesters are metabolites generated as a result of phthalate exposure. In compliance with the dictates of Green Analytical Chemistry, a rapid and simple protocol was developed and optimized for the quantification of phthalate monoesters (i.e., monoethyl phthalate, monoisobutyl phthalate, mono-n-butyl phthalate, mono-(2-ethylhexyl) phthalate, mono-n-octyl phthalate, monocyclohexyl phthalate, mono-isononyl phthalate) in human urine, which entails preceding derivatization with methyl chloroformate combined with the use of commercial solid phase microextraction and the analysis by gas chromatography-triple quadrupole mass spectrometry. The affinity of the derivatized analytes toward five commercial coatings was evaluated, and in terms of analyte extraction, the best results were reached with the use of the divinylbenzene/carboxen/polydimethylsiloxane fiber. The multivariate approach of experimental design was used to seek for the best working conditions of the derivatization reaction and the solid phase microextraction, thus obtaining the optimum response values. The proposed method was validated according to the guidelines issued by the Food and Drug Administration achieving satisfactory values in terms of linearity, sensitivity, matrix effect, intra- and inter-day accuracy, and precision.

Lanthanide Discrimination with Hydroxyl-Decorated Flexible Metal-Organic Frameworks.

We report two new highly crystalline metal-organic frameworks (MOFs), derived from the natural amino acids serine (1) and threonine (2), featuring hexagonal channels densely decorated with hydroxyl groups belonging to the amino acid residues. Both 1 and 2 are capable of discriminating, via solid-phase extraction, a mixture of selected chloride salts of lanthanides on the basis of their size, chemical affinity, and/or the flexibility of the network. In addition, this discrimination follows a completely different trend for 1 and 2 because of the different locations of the hydroxyl groups in each compound, which is evocative of steric complementarity between the substrate and receptor. Last but not least, the crystal structures of selected adsorbates could be resolved, offering unprecedented snapshots on the capture process and enabling structural correlations with the separation mechanism.

Investigating the robustness and extraction performance of a matrix-compatible solid-phase microextraction coating in human urine and its application to assess 2-6-ring polycyclic aromatic hydrocarbons using GC-MS/MS.

In this work, a polydimethylsiloxane/divinylbenzene fiber overcoated with a layer of polydimethylsiloxane was evaluated as analytical sampling tool for the first time in human urine. Urinary polycyclic aromatic hydrocarbons with 2-6 aromatic rings were considered as target compounds. The analyte uptake in kinetic and thermodynamic regime was evaluated and compared to the performances of polydimethylsiloxane/divinylbenzene and polydimethylsiloxane fibers. The assessment of the robustness and endurance of the overcoated fiber was carried out by direct immersion solid-phase microextraction in undiluted urine performing up to 120 consecutive extractions. The overcoated fiber was then used to develop a fast and easy direct immersion solid-phase microextraction with gas chromatography and triple quadrupole mass spectrometry protocol for the quantification of the target polycyclic aromatic hydrocarbons. The attained values of accuracy and precision were 75-114% and 2-19%, respectively, while the limits of quantification ranged between 0.05 and 1 ng/L. The proposed protocol was applied to the screening of urine samples collected from smoking and nonsmoking volunteers. The successful results obtained by using the overcoated fiber create not only new alternatives for polycyclic aromatic hydrocarbon exposure assessment but also new perspectives for the application of direct immersion solid-phase microextraction to the analysis of bioclinical matrixes.

Multivariate optimization of a microextraction by packed sorbent-programmed temperature vaporization-gas chromatography-tandem mass spectrometry method for organophosphate flame retardant analysis in environmental aqueous matrices.

In this work, organophosphate ester flame retardant (OPFRs) assay in environmental waters was addressed by using microextraction by packed sorbent (MEPS) and gas chromatography-tandem mass spectrometry (GC-MS/MS). Ten OPFRs with different physicochemical properties were taken into account as target compounds for a comprehensive method evaluation. Five MEPS cartridges (i.e., C2, C8, C18, Silica, and DVB) and seven solvents (i.e., methanol, ethyl acetate, methyl tert-butyl ether, hexane, acetonitrile, dichloromethane, and trichloromethane) were surveyed. The analysis was performed by using a gas chromatograph equipped with a programmed temperature vaporization injector (PTV). Univariate and multivariate approaches were exploited in order to optimize the parameters affecting the MEPS extraction and the PTV injection of the analytes into the gas chromatographic system. The optimal working conditions were achieved using DVB as sorbent material and acetonitrile as elution solvent. Internal standard calibration was carried out using TBP-d27 and TCEP-d12. Satisfactory values of accuracy and precision were generally obtained as well as limit of detection (2.7-99 pg/mL for tap water; 2.9-97 pg/mL for river water; 3-107 pg/mL for wastewater) and limit of quantification (0.01-0.2 ng/mL). The proposed protocol was evaluated on real case scenarios by analyzing tap water, river water and simulated wastewater samples. The developed method is not only eco-friendly due to the low use of organic solvents but also simple and automatable since the MEPS extraction procedure can be implemented in the autosampler routine. Graphical abstract The steps of the analytical protocol.

Efficient Nickel and Cobalt Recovery by Metal-Organic Framework-Based Mixed Matrix Membranes (MMM-MOFs).

Green energy transition has supposed to give a huge boost to the electric vehicle rechargeable battery market. This has generated a compelling demand for raw materials, such as cobalt and nickel, which are key common constituents in lithium-ion batteries (LIBs). However, their existing mining protocols and the concentrated localization of such ores have made cobalt and nickel mineral conundrums, and their supplies experience shortages, which threaten to slow the progress of the renewable energy transition. Aiming to contribute to the sustainable recycling of these valuable metals from LIBs and wastewater, in this work, we explore the use of four mixed matrix membranes (MMMs) embedding different metal-organic frameworks (MOFs), i.e., MIL-53(Al), MIL-53(Fe), MIL-101(Fe), and {SrIICuII 6[(S,S)-serimox]3(OH)2(H2O)}·39H2O (SrCu 6 Ser) in polyether sulfone (PES), for the recovery of cobalt(II) and nickel(II) metal cations from mixed cobalt-nickel aqueous solutions containing common interfering ions. Whereas the neat PES membrane slightly contributes to the adsorption of metal ions, showing reduced removal efficiency values of 10.2 and 9.5% for Ni(II) and Co(II), respectively, the inclusion of MOFs in the polymeric matrix substantially improves the adsorption performances. The four MOF@PES MMMs efficiently remove these metals from water, with MIL-53(Al)@PES being the one that presents better performance, with a removal efficiency up to 95% of Ni(II) and Co(II). Remarkably, SrCu 6 Ser@PES exhibits outstanding selectivity toward cobalt(II) cations compared to of nickel(II) ones, with removal efficiencies of 63.7 and 15.1% for Co(II) and Ni(II), respectively. Overall, the remarkable efficiencies, versatility, high environmental robustness, and cost-effective synthesis shown by this family of MOF@PES MMMs situate them among the best adsorbents for the extraction of this kind of contaminants.

A protocol based on solid phase microextraction -gas chromatography-tandem mass spectrometry for the monitoring of parabens and bisphenols in human saliva.

The herein presented work aims to the development of an easy method for the quantitative determination of parabens and bisphenols in human salivabased on the use of methyl chloroformate as a derivatizing agent, followed by solid-phase microextraction (SPME) and gas chromatography-triple quadrupole mass spectrometry (GC-QqQ-MS) analysis with selected reaction monitoring (SRM). Using multivariate analysis, two derivatization strategies were compared and optimized, demonstrating that the use of methyl chloroformate led to better sensitivity than the classical derivatization by acetic anhydride. Good performance in the sorption process of the derivatized target analytes was obtained using the most recent commercialized overcoated fiber (PDMS/DVB/PDMS). The validation procedure of the final protocol led to satisfactory results in terms of linearity, limit of quantitation, accuracy, and precision. All parabens were quantified from 10 ng/L using the developed method, except for methylparaben, which was quantified from 100 ng/L along with all bisphenols. Intra- and inter-day accuracy and intra- and inter-day precision can be considered satisfactory for all analytes (values between 73% and 118%), except for the inter-day accuracy of BPF. Quite good results also in terms of matrix effect were obtained for the target compounds (range 71% to 118%, RSD% less than 13.6%), except for BPA at the middle concentration and MeP at the lowest concentration. The greenness of the method was evaluated and the results indicated that our approach is more eco-friendly than previously published methods. Based on its characteristics, the presented method can be considered a suitable approach to determine parabens and bisphenols in routine analysis for biomonitoring purposes.

Assessment of benzothiazoles, benzotriazoles and benzenesulfonamides in environmental waters using an optimized combination of microextraction by packed sorbent with programmed temperature vaporization-gas chromatography tandem-mass spectrometry.

This work proposes a new method for the quantification of benzothiazoles (BTs), benzotriazoles (BTRs), and benzenesulfonamides (BSAs) in tap water, river water, and wastewater. The protocol involved the use of microextraction by packed sorbent (MEPS), applied for the first time for the extraction of the target analytes, combined with programmed temperature vaporization-gas chromatography-triple quadrupole mass spectrometry (PTV-GC-QqQ-MS). Considering the synergism between MEPS extraction and PTV injection, the experimental variables affecting their performance were simultaneously optimized by "experimental design", while principal component analysis (PCA) was used to find the overall optimal working conditions. Response surface methodology was used to gain a comprehensive understanding of the effects of working variables on method performance. The developed method achieved very good linearities and satisfactory intra- and inter-day accuracies and precisions. The protocol permitted the detection of the target molecules with limit of detection (LODs) values between 0.005 and 0.85 µg/L. The green character of the procedure was evaluated using three metrics: "Analytical Eco-Scale", "Green Analytical Procedure Index" (GAPI), and "Analytical Greenness metric for sample preparation (AGREEprep). The satisfactory results obtained with real water samples demonstrate the applicability of the method for monitoring campaigns and exposome studies.

An innovative green protocol for the quantification of benzothiazoles, benzotriazoles and benzosulfonamides in PM10 using microwave-assisted extraction coupled with solid-phase microextraction gas chromatography tandem-mass spectrometry.

Benzothiazoles (BTHs), benzotriazoles (BTRs), and benzenesulfonamides (BSAs) are chemicals used in several industrial and household applications. Despite these compounds are emerging pollutants, there is still a lack of information about their presence in outdoor air samples. In this paper, we developed a new method for the quantification of BTHs, BTRs, and BSAs in airborne particulate matter (PM10). The extraction of fourteen analytes from PM10 was accomplished by microwave-assisted extraction (MAE) using an environmentally friendly mixture of water and ethanol. SPME was used to analyze the target compounds from the MAE extract by gas chromatography-tandem mass spectrometry (SPME-GC-MS/MS), eliminating additional sample clean-up steps. The best working conditions for MAE and SPME were examined multivariately by experimental design techniques. The target compounds were quantified in selected reaction monitoring acquisition mode. The proposed method was carefully validated, and the achieved results were satisfactory in terms of linearity, lower limit of quantification (picograms per cubic meter), intra- and inter-day accuracy (81-118% and 82-114%, respectively), and precision (repeatability and reproducibility in the range 2.3-17% and 7.4-19%, respectively). The application in a real monitoring campaign showed that the developed protocol is a valuable and eco-friendly alternative to the methods proposed so far.

Agrochemical treatments as a source of heavy metals and rare earth elements in agricultural soils and bioaccumulation in ground beetles.

The continuous and extensive application of agrochemicals leads to the accumulation of heavy metals (HMs) and rare earth elements (REEs) in agricultural soils and their transfer in the food web with consequent relevant risks for human and ecosystem health. In this study, HM and REE concentrations were quantified in the soil of wheat crop fields conventionally managed in the agricultural areas of Sila Mountain (Southern Italy) and compared with the concentration in a field of wild herbs, used as control. Statistical analyses and principal component analysis suggested that the use of pesticides, herbicides and fertilizers contributes to the accumulation of HMs and REEs in the soil. Different accumulation patterns were recorded in treated fields as a consequence of the type and amount of agrochemical used and the crop rotation. The exposure risk associated with the transfer through the tropic levels of agroecosystem was carried out measuring the concentration of HMs and REEs in adults of Harpalus (Pseudoophonus) rufipes (De Geer, 1774) collected from each monitored site. Different accumulation patterns found in specimens from the monitored sites highlighted the ability of this generalist predator to regulate metal uptake under field conditions. The values of bioaccumulation factor (BAF) allow to defining the order of accumulation in P. rufipes which was classified as a macroconcentrator of Cd, Cu, Mg and Zn. Our results can supplement the limited information regarding the REE accumulation in soil invertebrates and may provide reference data for assessing potential environmental risks in croplands.

Development of a fast and simple gas chromatographic protocol based on the combined use of alkyl chloroformate and solid phase microextraction for the assay of polyamines in human urine.

Polyamines are aliphatic amines with low molecular weight that are widely recognized as one of the most important cancer biomarkers for early diagnosis and treatment. The goal of the work herein presented is the development of a rapid and simple method for the quantification of free polyamines (i.e., putrescine, cadaverine, spermidine, spermine) and N-monoacetylated polyamines (i.e., N1-Acetylspermidine, N8-Acetylspermidine, and N1-Acetylspermine) in human urine. A preliminary derivatization with propyl chloroformate combined with the use of solid phase microextraction (SPME) allowed for an easy and automatable protocol involving minimal sample handling and no consumption of organic solvents. The affinity of the analytes toward five commercial SPME coatings was evaluated in univariate mode, and the best result in terms of analyte extraction was achieved using the divinylbenzene/carboxen/polydimethylsiloxane fiber. The variables affecting the performance of SPME analysis were optimized by the multivariate approach of experimental design and, in particular, using a central composite design (CCD). The optimal working conditions in terms of response values are the following: extraction temperature 40 °C, extraction time of 15 min and no addition of NaCl. Analyses were carried out by gas chromatography-triple quadrupole mass spectrometry (GC-QqQ-MS) in selected reaction monitoring (SRM) acquisition mode. The developed method was validated according to the guidelines issued by the Food and Drug Administration (FDA). The satisfactory performances reached in terms of linearity, sensitivity (LOQs between 0.01 and 0.1 µg/mL), matrix effect (68-121%), accuracy, and precision (inter-day values between -24% and +16% and in the range 3.3-28.4%, respectively) make the proposed protocol suitable to be adopted for quantification of these important biomarkers in urine samples.

Industrial Waste Treatment by ETS-10 Ion Exchanger Material.

The aim of this project was to study the treatment of industrial waste using ETS-10 zeolite. The pollutants that must be removed were metals sourced from zinc ferrite, a processing waste derived from the use of mineral-containing zinc. The first phase of the work involved the characterization of the industrial waste, zinc ferrite, in order to deepen the knowledge regarding its nature and composition. The second phase involved the removal of the metals released by the zinc ferrite in aqueous systems using the ETS-10 phase as an ion exchanger. Different chemical and physical techniques were used: plasma mass spectrometry, X-ray diffraction, scanning electron microscopy, microanalysis, and thermal analyses. A comparison between ETS-10 and commercial zeolite A performance, in the same aqueous systems, was carried out. The results showed that the metal removal efficiency of ETS-10 phase is higher than that obtained by commercial zeolite A, especially towards dangerous heavy metals such as Pb, Zn and Mn.

A green approach for organophosphate ester determination in airborne particulate matter: Microwave-assisted extraction using hydroalcoholic mixture coupled with solid-phase microextraction gas chromatography-tandem mass spectrometry.

Particulate matter (PM) is among the most dangerous air pollutants, and there is a growing concern related to the effects of airborne particles on human health. Their harmful effects can be derived are directly linked to the size of particles themselves and the associated pollutants after they have been taken up by inhalation. In this work was developed a new analytical method for the quantification of organophosphorus esters (OPE) bound to airborne PM. The proposed protocol provides for the microwave-assisted extraction (MAE) of the analytes from the PM followed by solid-phase microextraction gas chromatography-tandem mass spectrometry determination (SPME-GC-MS/MS). Unlike to the traditional protocol, which provides for the use of tedious Soxhlet extraction with environmentally damaging organic solvents, the proposed method allows for a reliable quantification by using an eco-friendly hydroalcoholic mixture (water/ethanol; 50:50, v/v). The method was developed using as target compounds ten organophosphate esters, namely tripropyl phosphate (TPP), tri-n-butyl phosphate (TBP), tris(2-chloroethyl) phosphate (TCEP), tris(1-chloro-2-propyl) phosphate (TCPP), tris(1,3-dichloro-2-propyl) phosphate (TDCPP), tributoxyethyl phosphate (TBEP), triphenyl phosphate (TPhP), 2-ethylhexyl-diphenyl phosphate (EHDPP), tris(2-ethylhexyl) phosphate (TEHP) and tricresyl phosphate (TCP). The extraction performance of five SPME fibers was evaluated and the DVB/CAR/PDMS coating demonstrated to be the most suitable for the extraction of the target analytes. Experimental Design was used for the multivariate optimization of the parameters affecting the MAE process as well as the SPME extraction, and the optimal working conditions were determined by using Derringer's desirability function. The developed method was validated in terms of linearity, sensitivity (LLOQ values of 0.5 ng/mL for TDCPP and 0.1 ng/mL for the other analytes), matrix effect (81-117%), intra and inter day accuracy (83-115% and 80-115%, respectively), and precision (repeatability and reproducibility in the range 1.0-12.4% and 2.3-15.2%, respectively). The satisfactory performances reached make the proposed protocol a green and high-throughput alternative for OPE quantification in particulate matter.

Gi Protein Modulation of the Potassium Channel TASK-2 Mediates Vesicle Osmotic Swelling to Facilitate the Fusion of Aquaporin-2 Water Channel Containing Vesicles.

Vesicle fusion is a fundamental cell biological process similar from yeasts to humans. For secretory vesicles, swelling is considered a step required for the expulsion of intravesicular content. Here this concept is revisited providing evidence that it may instead represent a general mechanism. We report the first example that non-secretory vesicles, committed to insert the Aquaporin-2 water channel into the plasma membrane, swell and this phenomenon is required for fusion to plasma membrane. Through an interdisciplinary approach, using atomic force microscope (AFM), a fluorescence-based assay of vesicle volume changes and NMR spectroscopy to measure water self-diffusion coefficient, we provide evidence that Gi protein modulation of potassium channel TASK-2 localized in AQP2 vesicles, is required for vesicle swelling. Estimated intravesicular K⁺ concentration in AQP2 vesicles, as measured by inductively coupled plasma mass spectrometry, was 5.3 mM, demonstrating the existence of an inwardly K⁺ chemical gradient likely generating an osmotic gradient causing vesicle swelling upon TASK-2 gating. Of note, abrogation of K⁺ gradient significantly impaired fusion between vesicles and plasma membrane. We conclude that vesicle swelling is a potentially important prerequisite for vesicle fusion to the plasma membrane and may be required also for other non-secretory vesicles, depicting a general mechanism for vesicle fusion.

A fast and simple solid phase microextraction coupled with gas chromatography-triple quadrupole mass spectrometry method for the assay of urinary markers of glutaric acidemias.

The analysis of characteristic urinary acidic markers such as glutaric, 3-hydroxyglutaric, 2-hydroxyglutaric, adipic, suberic, sebacic, ethylmalonic, 3-hydroxyisovaleric and isobutyric acid constitutes the recommended follow-up testing procedure for glutaric acidemia type 1 (GA-1) and type 2 (GA-2). The goal of the work herein presented is the development of a fast and simple method for the quantification of these biomarkers in human urine. The proposed analytical approach is based on the use of solid phase microextraction (SPME) combined with gas chromatography-triple quadrupole mass spectrometry (GC-QqQ-MS) afterward a rapid derivatization of acidic moieties by propyl chloroformate, propanol and pyridine. Trueness and precision of the proposed protocol, tested at 5, 30 and 80mgl-1, provided satisfactory values: recoveries were in the range between 72% and 116% and the relative standard deviations (RSD%) were between 0.9% and 18% (except for isobutyric acid at 5mgl-1). The LOD values achieved by the proposed method ranged between 1.0 and 473µgl-1.