RESUMO
Metal oxide 1D nanowires are probably the most promising structures to develop cheap stable and selective chemical sensors. The purpose of this contribution is to review almost two-decades of research activity at the Sensor Lab Brescia on their preparation during by vapor solid (n-type In2O3, ZnO), vapor liquid solid (n-type SnO2 and p-type NiO) and thermal evaporation and oxidation (n-type ZnO, WO3 and p-type CuO) methods. For each material we've assessed the chemical sensing performance in relation to the preparation conditions and established a rank in the detection of environmental and industrial pollutants: SnO2 nanowires were effective in DMMP detection, ZnO nanowires in NO2, acetone and ethanol detection, WO3 for ammonia and CuO for ozone.
RESUMO
Metallic implants and devices are widely used in the orthopedic and orthodontic clinical areas. However, several problems regarding their adhesion with the living tissues and inflammatory responses due to the release of metallic ions to the medium have been reported. The modification of the metallic surfaces and the use of biocompatible protective coatings are two approaches to solve such issues. In this study, in order to improve the adhesion properties and to increase the corrosion resistance of metallic Ti substrates we have obtained a hybrid structure based on TiO2 nanotubular arrays and PDMS-TEOS films. TiO2 nanotubes have been prepared with two different diameters by means of electrochemical anodization. PDMS-TEOS films have been prepared by the sol-gel method. The morphological and the elemental analysis of the structures have been investigated by scanning electron microscopy and energy dispersive spectroscopy (EDS). Electrochemical impedance spectroscopy (EIS) and polarization curves have been performed during immersion of the samples in Kokubo's simulated body fluid (SBF) at 37 °C to study the effect of structure layers and tube diameter on the protective properties. The obtained results show that the modification of the surface structure of TiO2 and the application of PDMS-TEOS film is a promising strategy for the development of implant materials.
Assuntos
Materiais Revestidos Biocompatíveis/síntese química , Dimetilpolisiloxanos/química , Nanotubos/química , Nylons/química , Silanos/química , Titânio/química , Eletroquímica , Humanos , Teste de Materiais , Nanotubos/ultraestruturaRESUMO
Synthesis--particularly by electrochemical anodization-, growth mechanism and chemical sensing properties of pure, doped and mixed titania tubular arrays are reviewed. The first part deals on how anodization parameters affect the size, shape and morphology of titania nanotubes. In the second part fabrication of sensing devices based on titania nanotubes is presented, together with their most notable gas sensing performances. Doping largely improves conductivity and enhances gas sensing performances of TiO2 nanotubes.
Assuntos
Técnicas Eletroquímicas , Gases/análise , Nanotubos , TitânioRESUMO
Synthesis of Nb-containing titania nanotubular arrays at room temperature by electrochemical anodization is reported. Crystallization of pure and Nb-doped TiO(2) nanotubes was carried out by post-growth annealing at 400°C. The morphology of the tubes obtained was characterized by scanning electron microscopy (SEM). Crystal structure and composition of tubes were investigated by glancing incidence x-ray diffraction (GIXRD) and total reflection x-ray fluorescence (TXRF). For the first time gas sensing characteristics of Nb-doped TiO(2) nanotubes were investigated and compared to those of undoped nanotubes. The functional properties of nanotubular arrays towards CO, H(2), NO(2), ethanol and acetone were tested in a wide range of operating temperature. The introduction of Nb largely improves conductivity and enhances gas sensing performances of TiO(2) nanotubes.
Assuntos
Gases/análise , Nanoestruturas/química , Nanoestruturas/ultraestrutura , Nióbio/química , Titânio/química , Transdutores , Desenho de Equipamento , Análise de Falha de Equipamento , Tamanho da PartículaRESUMO
Gelatin-dextran hydrogel scaffolds (G-PEG-Dx) were evaluated for their ability to activate the bone marrow human mesenchymal stromal cells (BM-hMSCs) towards mineralization. G-PEG-Dx1 and G-PEG-Dx2, with identical composition but different architecture, were seeded with BM-hMSCs in presence of fetal bovine serum or human platelet lysate (hPL) with or without osteogenic medium. G-PEG-Dx1, characterized by a lower degree of crosslinking and larger pores, was able to induce a better cell colonization than G-PEG-Dx2. At day 28, G-PEG-Dx2, with hPL and osteogenic factors, was more efficient than G-PEG-Dx1 in inducing mineralization. Scanning electron microscopy (SEM) and Raman spectroscopy showed that extracellular matrix produced by BM-hMSCs and calcium-positive mineralization were present along the backbone of the G-PEG-Dx2, even though it was colonized to a lesser degree by hMSCs than G-PEG-Dx1. These findings were confirmed by matrix-assisted laser desorption/ionization mass spectrometry imaging (MALDI-MSI), detecting distinct lipidomic signatures that were associated with the different degree of scaffold mineralization. Our data show that the architecture and morphology of G-PEG-Dx2 is determinant and better than that of G-PEG-Dx1 in promoting a faster mineralization, suggesting a more favorable and active role for improving bone repair.
RESUMO
A simple and large-area scalable methodology has been set up for direct integration of metal oxide nanowire bundles into a functional device for gas sensing. It is based on sequential application of two consolidated techniques, namely high temperature vapour transport and condensation for fabrication of metal oxide nanowires, and wet etching of a sacrificial layer. The alumina substrate patterned with a silicon dioxide sacrificial layer does not influence the growth of nanowires and remains unaltered under the high temperature process. The sacrificial layer is finally removed under hydrofluoric acid, the metal oxide nanowires do not suffer modifications and a clean substrate surface can be obtained for deposition of stable metal contacts. The methodology was proven effective for application in a gas sensor device. Electrical measurements indicate that a slightly rectifying Schottky junction is present at low temperatures (up to T = 150 degrees C) between nanowires and platinum electrodes, which vanishes as the temperature increases and under high voltage (bias voltage above approximately 3 V). The results foresee the possibility of growth and integration of nanowire bundles directly into devices, overcoming the need for expensive and time-consuming nanomanipulation techniques.
RESUMO
A hybrid nanostructure based on reduced graphene oxide and ZnO has been obtained for the detection of volatile organic compounds. The sensing properties of the hybrid structure have been studied for different concentrations of ethanol and acetone. The response of the hybrid material is significantly higher compared to pristine ZnO nanostructures. The obtained results have shown that the nanohybrid is a promising structure for the monitoring of environmental pollutants and for the application of breath tests in assessment of exposure to volatile organic compounds.
RESUMO
TiO2 anatase nanocrystals were prepared by solvothermal processing of Ti chloroalkoxide in oleic acid, in the presence of W chloroalkoxide, with W/Ti nominal atomic concentration (R(w)) ranging from 0.16 to 0.64. The as-prepared materials were heat-treated up to 500 °C for thermal stabilization and sensing device processing. For R(0.16), the as-prepared materials were constituted by an anatase core surface-modified by WO(x) monolayers. This structure persisted up to 500 °C, without any WO3 phase segregation. For R(w) up to R(0.64), the anatase core was initially wrapped by an amorphous WO(x) gel. Upon heat treatment, the WO(x) phase underwent structural reorganization, remaining amorphous up to 400 °C and forming tiny WO3 nanocrystals dispersed into the TiO2 host after heating at 500 °C, when part of tungsten also migrated into the TiO2 structure, resulting in structural and electrical modification of the anatase host. The ethanol sensing properties of the various materials were tested and compared with pure TiO2 and WO3 analogously prepared. They showed that even the simple surface modification of the TiO2 host resulted in a 3 orders of magnitude response improvement with respect to pure TiO2.
RESUMO
Zinc oxide (ZnO, n-type) and copper oxide (CuO, p-type) nanowires have been synthesized and preliminarily investigated as innovative materials for the fabrication of a proof-of-concept thermoelectric device. The Seebeck coefficients, electrical conductivity and thermoelectric power factors (TPF) of both semiconductor materials have been determined independently using a custom experimental set-up, leading to results in agreement with available literature with potential improvement. Combining bundles of ZnO and CuO nanowires in a series of five thermocouples on alumina leads to a macroscopic prototype of a planar thermoelectric generator (TEG) unit. This demonstrates the possibility of further integration of metal oxide nanostructures into efficient thermoelectric devices.
RESUMO
We report for the first time the synthesis of monoclinic WO3 quantum dots. A solvothermal processing at 250 °C in oleic acid of W chloroalkoxide solutions was employed. It was shown that the bulk monoclinic crystallographic phase is the stable one even for the nanosized regime (mean size 4 nm). The nanocrystals were characterized by X-ray diffraction, High resolution transmission electron microscopy, X-ray photoelectron spectroscopy, UV-vis, Fourier transform infrared and Raman spectroscopy. It was concluded that they were constituted by a core of monoclinic WO3, surface covered by unstable W(V) species, slowly oxidized upon standing in room conditions. The WO3 nanocrystals could be easily processed to prepare gas-sensing devices, without any phase transition up to at least 500 °C. The devices displayed remarkable response to both oxidizing (nitrogen dioxide) and reducing (ethanol) gases in concentrations ranging from 1 to 5 ppm and from 100 to 500 ppm, at low operating temperatures of 100 and 200 °C, respectively. The analysis of the electrical data showed that the nanocrystals were characterized by reduced surfaces, which enhanced both nitrogen dioxide adsorption and oxygen ionosorption, the latter resulting in enhanced ethanol decomposition kinetics.
RESUMO
Surface coating with an organic self-assembled monolayer (SAM) can enhance surface reactions or the absorption of specific gases and hence improve the response of a metal oxide (MOx) sensor toward particular target gases in the environment. In this study the effect of an adsorbed organic layer on the dynamic response of zinc oxide nanowire gas sensors was investigated. The effect of ZnO surface functionalisation by two different organic molecules, tris(hydroxymethyl)aminomethane (THMA) and dodecanethiol (DT), was studied. The response towards ammonia, nitrous oxide and nitrogen dioxide was investigated for three sensor configurations, namely pure ZnO nanowires, organic-coated ZnO nanowires and ZnO nanowires covered with a sparse layer of organic-coated ZnO nanoparticles. Exposure of the nanowire sensors to the oxidising gas NO(2) produced a significant and reproducible response. ZnO and THMA-coated ZnO nanowire sensors both readily detected NO(2) down to a concentration in the very low ppm range. Notably, the THMA-coated nanowires consistently displayed a small, enhanced response to NO(2) compared to uncoated ZnO nanowire sensors. At the lower concentration levels tested, ZnO nanowire sensors that were coated with THMA-capped ZnO nanoparticles were found to exhibit the greatest enhanced response. ΔR/R was two times greater than that for the as-prepared ZnO nanowire sensors. It is proposed that the ΔR/R enhancement in this case originates from the changes induced in the depletion-layer width of the ZnO nanoparticles that bridge ZnO nanowires resulting from THMA ligand binding to the surface of the particle coating. The heightened response and selectivity to the NO(2) target are positive results arising from the coating of these ZnO nanowire sensors with organic-SAM-functionalised ZnO nanoparticles.
RESUMO
Electrochemical anodization of a titanium film on a Kapton HN substrate leads to the formation of closely packed aligned nanotubes, whose shape can be finely tuned by tailoring the anodization parameters. An amorphous-to-anatase phase transition is induced on nanotubes by annealing at 350 °C. The nanotubes are applied as photoanodes in flexible dye-sensitized solar cells (N719 dye; I3-/I- redox couple), resulting in a photoconversion efficiency of up to 3.5% under simulated sunlight irradiation air mass 1.5 global (AM 1.5G).
RESUMO
Density functional theory (DFT) modelling of the alkane-SnO2 surface interaction correctly predicts the results of the chemoresistive alkane sensing tests, provided that the highly reduced nature of the SnO2 nanocrystal surface is properly inserted in the model.