A Difluoro-Methoxylated Ending-Group Asymmetric Small Molecule Acceptor Lead Efficient Binary Organic Photovoltaic Blend.

Developing a new end group for synthesizing asymmetric small molecule acceptors (SMAs) is crucial for achieving high-performance organic photovoltaics (OPVs). Herein, an asymmetric small molecule acceptor, BTP-BO-4FO, featuring a new difluoro-methoxylated end-group is reported. Compared to its symmetric counterpart L8-BO, BTP-BO-4FO exhibits an upshifted energy level, larger dipole moment, and more sequential crystallinity. By adopting two representative and widely available solvent additives (1-chloronaphthalene (CN) and 1,8-diiodooctane (DIO)), the device based on PM6:BTP-BO-4FO (CN) photovoltaic blend demonstrates a power conversion efficiency (PCE) of 18.62% with an excellent open-circuit voltage (VOC) of 0.933 V, which surpasses the optimal result of L8-BO. The PCE of 18.62% realizes the best efficiencies for binary OPVs based on SMAs with asymmetric end groups. A series of investigations reveal that optimized PM6:BTP-BO-4FO film demonstrates similar molecular packing motif and fibrillar phase distribution as PM6:L8-BO (DIO) does, resulting in comparable recombination dynamics, thus, similar fill factor. Besides, it is found PM6:BTP-BO-4FO possesses more efficient charge generation, which yields better VOC-JSC balance. This study provides a new ending group that enables a cutting-edge efficiency in asymmetric SMA-based OPVs, enriching the material library and shed light on further design ideas.

Glycol Monomethyl Ether-Substituted Carbazolyl Hole-Transporting Material for Stable Inverted Perovskite Solar Cells with Efficiency of 25.52.

Organic self-assembled molecules (OSAMs) based hole transporting materials play a pivotal role in achieving highly efficient and stable inverted perovskite solar cells (IPSCs). However, the reported carbazol-based OSAMs have serious drawbacks, such as poor solubility in alcohol solution, worse matched energy arrangement with perovskite, and limited molecular species, which greatly limit the device performance. To address above problems, a novel OSAM 4-(3,6-glycol monomethyl ether-9H-carbazol-9-yl) butyl]phosphonic acid (GM-4PACz) was synthesized as hole-transporting material by introducing glycol monomethyl ether (GM) side chains at carbazolyl unit. GM groups enhance the surface energy of Indium Tin Oxide (ITO)/SAM substrate to facilitate the nucleation and growth of up perovskite film, suppress cation defects, release the residual stress at SAM/perovskite interface, and evaluate energy level for matching with perovskite. Consequently, the GM-4PACz based IPSC achieves a champion PCE of 25.52%, a respectable open-circuit voltage (VOC) of 1.21 V, a high stability, possessing 93.29% and 91.75% of their initial efficiency after aging in air for 2000 h or tracking at maximum power point for 1000 h, respectively.

Non-Fully Conjugated Dimerized Giant Acceptors with Different Alkyl-Linked Sites for Stable and 19.13 % Efficiency Organic Solar Cells.

Achieving both high power conversion efficiency (PCE) and device stability is a major challenge for the practical development of organic solar cells (OSCs). Herein, three non-fully conjugated dimerized giant acceptors (named 2Y-sites, including wing-site-linked 2Y-wing, core-site-linked 2Y-core, and end-site-linked 2Y-end) are developed. They share the similar monomer precursors but have different alkyl-linked sites, offering the fine-tuned molecular absorption, packing, glass transition temperature, and carrier mobility. Among their binary active layers, D18/2Y-wing has better miscibility, leading to optimized morphology and more efficient charge transfer compared to D18/2Y-core and D18/2Y-end. Therefore, the D18/2Y-wing-based OSCs achieve a superior PCE of 17.73 %, attributed to enhanced photocurrent and fill factor. Furthermore, the D18/2Y-wing-based OSCs exhibit a balance of high PCE and improved stability, distinguishing them within the 2Y-sites. Building on the success of 2Y-wing in binary systems, we extend its application to ternary OSCs by pairing it with the near-infrared absorbing D18/BS3TSe-4F host. Thanks to the complementary absorption within 300-970 nm and further optimized morphology, ternary OSCs obtain a higher PCE of 19.13 %, setting a new efficiency benchmark for the dimer-derived OSCs. This approach of alkyl-linked site engineering for constructing dimerized giant acceptors presents a promising pathway to improve both PCE and stability of OSCs.

Correlation of Local Isomerization Induced Lateral and Terminal Torsions with Performance and Stability of Organic Photovoltaics.

Organic photovoltaics (OPVs) have achieved great progress in recent years due to delicately designed non-fullerene acceptors (NFAs). Compared with tailoring of the aromatic heterocycles on the NFA backbone, the incorporation of conjugated side-groups is a cost-effective way to improve the photoelectrical properties of NFAs. However, the modifications of side-groups also need to consider their effects on device stability since the molecular planarity changes induced by side-groups are related to the NFA aggregation and the evolution of the blend morphology under stresses. Herein, a new class of NFAs with local-isomerized conjugated side-groups are developed and the impact of local isomerization on their geometries and device performance/stability are systematically investigated. The device based on one of the isomers with balanced side- and terminal-group torsion angles can deliver an impressive power conversion efficiency (PCE) of 18.5%, with a low energy loss (0.528 V) and an excellent photo- and thermal stability. A similar approach can also be applied to another polymer donor to achieve an even higher PCE of 18.8%, which is among the highest efficiencies obtained for binary OPVs. This work demonstrates the effectiveness of applying local isomerization to fine-tune the side-group steric effect and non-covalent interactions between side-group and backbone, therefore improving both photovoltaic performance and stability of fused ring NFA-based OPVs.

Dimer Acceptor Adopting a Flexible Linker for Efficient and Durable Organic Solar Cells.

Organic solar cells (OSCs) have advanced rapidly due to the development of new photovoltaic materials. However, the long-term stability of OSCs still poses a severe challenge for their commercial deployment. To address this issue, a dimer acceptor (dT9TBO) with flexible linker is developed for incorporation into small-molecule acceptors to form molecular alloy with enhanced intermolecular packing and suppressed molecular diffusion to stabilize active layer morphology. Consequently, the PM6 : Y6 : dT9TBO-based device displays an improved power conversion efficiency (PCE) of 18.41 % with excellent thermal stability and negligible decay after being aged at 65 °C for 1800 h. Moreover, the PM6 : Y6 : dT9TBO-based flexible OSC also exhibits excellent mechanical durability, maintaining 95 % of its initial PCE after being bended repetitively for 1500 cycles. This work provides a simple and effective way to fine-tune the molecular packing with stabilized morphology to overcome the trade-off between OSC efficiency and stability.

Correlation of Broad Absorption Band with Small Singlet-Triplet Energy Gap in Organic Photovoltaics.

Organic photovoltaics (OPV) are one of the most effective ways to harvest renewable solar energy, with the power conversion efficiency (PCE) of the devices soaring above 19 % when processed with halogenated solvents. The superior photocurrent of OPV over other emerging photovoltaics offers more opportunities to further improve the efficiency. Tailoring the absorption band of photoactive materials is an effective way to further enhance OPV photocurrent. However, the field has mostly been focusing on improving the near-infrared region photo-response, with the absorption shoulders in short-wavelength region (SWR) usually being neglected. Herein, by developing a series of non-fullerene acceptors (NFAs) with varied side-group conjugations, we observe an enhanced SWR absorption band with increased side-group conjugation length. The underpinning factors of how molecular structures and geometries improve SWR absorption are clearly elucidated through theoretical modelling and crystallography. Moreover, a clear relationship between the enhanced SWR absorption and reduced singlet-triplet energy gap is established, both of which are favorable for the OPV performance and can be tailored by rational structure design of NFAs. Finally, the rationally designed NFA, BO-TTBr, affords a decent PCE of 18.5 % when processed with a non-halogenated green solvent.

Unidirectional Sidechain Engineering to Construct Dual-Asymmetric Acceptors for 19.23 % Efficiency Organic Solar Cells with Low Energy Loss and Efficient Charge Transfer.

Achieving both high open-circuit voltage (Voc ) and short-circuit current density (Jsc ) to boost power-conversion efficiency (PCE) is a major challenge for organic solar cells (OSCs), wherein high energy loss (Eloss ) and inefficient charge transfer usually take place. Here, three new Y-series acceptors of mono-asymmetric asy-YC11 and dual-asymmetric bi-asy-YC9 and bi-asy-YC12 are developed. They share the same asymmetric D1 AD2 (D1 =thieno[3,2-b]thiophene and D2 =selenopheno[3,2-b]thiophene) fused-core but have different unidirectional sidechain on D1 side, allowing fine-tuned molecular properties, such as intermolecular interaction, packing pattern, and crystallinity. Among the binary blends, the PM6 : bi-asy-YC12 one has better morphology with appropriate phase separation and higher order packing than the PM6 : asy-YC9 and PM6 : bi-asy-YC11 ones. Therefore, the PM6 : bi-asy-YC12-based OSCs offer a higher PCE of 17.16 % with both high Voc and Jsc , due to the reduced Eloss and efficient charge transfer properties. Inspired by the high Voc and strong NIR-absorption, bi-asy-YC12 is introduced into efficient binary PM6 : L8-BO to construct ternary OSCs. Thanks to the broadened absorption, optimized morphology, and furtherly minimized Eloss , the PM6 : L8-BO : bi-asy-YC12-based OSCs achieve a champion PCE of 19.23 %, which is one of the highest efficiencies among these annealing-free devices. Our developed unidirectional sidechain engineering for constructing bi-asymmetric Y-series acceptors provides an approach to boost PCE of OSCs.

High Efficiency (15.8%) All-Polymer Solar Cells Enabled by a Regioregular Narrow Bandgap Polymer Acceptor.

Despite the significant progresses made in all-polymer solar cells (all-PSCs) recently, the relatively low short-circuit current density (Jsc) and large energy loss are still quite difficult to overcome for further development. To address these challenges, we developed a new class of narrow-bandgap polymer acceptors incorporating a benzotriazole (BTz)-core fused-ring segment, named the PZT series. Compared to the commonly used benzothiadiazole (BT)-containing polymer PYT, the less electron-deficient BTz renders PZT derivatives with significantly red-shifted optical absorption and up-shifted energy levels, leading to simultaneously improved Jsc and open-circuit voltage in the resultant all-PSCs. More importantly, a regioregular PZT (PZT-γ) has been developed to achieve higher regiospecificity for avoiding the formation of isomers during polymerization. Benefiting from the more extended absorption, better backbone ordering, and more optimal blend morphology with donor component, PZT-γ-based all-PSCs exhibit a record-high power conversion efficiency of 15.8% with a greatly enhanced Jsc of 24.7 mA/cm2 and a low energy loss of 0.51 eV.

Multi-Selenophene-Containing Narrow Bandgap Polymer Acceptors for All-Polymer Solar Cells with over 15 % Efficiency and High Reproducibility.

All-polymer solar cells (all-PSCs) progressed tremendously due to recent advances in polymerized small molecule acceptors (PSMAs), and their power conversion efficiencies (PCEs) have exceeded 15 %. However, the practical applications of all-PSCs are still restricted by a lack of PSMAs with a broad absorption, high electron mobility, low energy loss, and good batch-to-batch reproducibility. A multi-selenophene-containing PSMA, PFY-3Se, was developed based on a selenophene-fused SMA framework and a selenophene π-spacer. Compared to its thiophene analogue PFY-0Se, PFY-3Se shows a ≈30 nm red-shifted absorption, increased electron mobility, and improved intermolecular interaction. In all-PSCs, PFY-3Se achieved an impressive PCE of 15.1 % with both high short-circuit current density of 23.6 mA cm-2 and high fill factor of 0.737, and a low energy loss, which are among the best values in all-PSCs reported to date and much better than PFY-0Se (PCE=13.0 %). Notably, PFY-3Se maintains similarly good batch-to-batch properties for realizing reproducible device performance, which is the first reported and also very rare for the PSMAs. Moreover, the PFY-3Se-based all-PSCs show low dependence of PCE on device area (0.045-1.0 cm2 ) and active layer thickness (110-250 nm), indicating the great potential toward practical applications.

Optimized Active Layer Morphologies via Ternary Copolymerization of Polymer Donors for 17.6 % Efficiency Organic Solar Cells with Enhanced Fill Factor.

Regulating molecular structure to optimize the active layer morphology is of considerable significance for improving the power conversion efficiencies (PCEs) in organic solar cells (OSCs). Herein, we demonstrated a simple ternary copolymerization approach to develop a terpolymer donor PM6-Tz20 by incorporating the 5,5'-dithienyl-2,2'-bithiazole (DTBTz, 20 mol%) unit into the backbone of PM6 (PM6-Tz00). This method can effectively tailor the molecular orientation and aggregation of the polymer, and then optimize the active layer morphology and the corresponding physical processes of devices, ultimately boosting FF and then PCE. Hence, the PM6-Tz20: Y6-based OSCs achieved a PCE of up to 17.1% with a significantly enhanced FF of 0.77. Using Ag (220 nm) instead of Al (100 nm) as cathode, the champion PCE was further improved to 17.6%. This work provides a simple and effective molecular design strategy to optimize the active layer morphology of OSCs for improving photovoltaic performance.

A Non-Conjugated Polymer Acceptor for Efficient and Thermally Stable All-Polymer Solar Cells.

A non-conjugated polymer acceptor PF1-TS4 was firstly synthesized by embedding a thioalkyl segment in the mainchain, which shows excellent photophysical properties on par with a fully conjugated polymer, with a low optical band gap of 1.58 eV and a high absorption coefficient >105  cm-1 , a high LUMO level of -3.89 eV, and suitable crystallinity. Matched with the polymer donor PM6, the PF1-TS4-based all-PSC achieved a power conversion efficiency (PCE) of 8.63 %, which is ≈45 % higher than that of a device based on the small molecule acceptor counterpart IDIC16. Moreover, the PF1-TS4-based all-PSC has good thermal stability with ≈70 % of its initial PCE retained after being stored at 85 °C for 180 h, while the IDIC16-based device only retained ≈50 % of its initial PCE when stored at 85 °C for only 18 h. Our work provides a new strategy to develop efficient polymer acceptor materials by linkage of conjugated units with non-conjugated thioalkyl segments.

High-Performance Nonfullerene Polymer Solar Cells Based on a Wide-Bandgap Polymer without Extra Treatment.

Nonfullerene polymer solar cells (PSCs) are developed based on a fluorinated thienyl-based wide-bandgap (WBG) polymer PBBF as the electron donor and nonfullerene small molecule IDIC as the electron acceptor. PBBF exhibits a strong absorption in the range of 300-605 nm with a wide optical bandgap of 2.05 eV, which is complementary with that of IDIC. Meanwhile, it possesses a deeper highest occupied molecular orbital energy level of  -5.52 eV and a higher hole mobility of 7.3 × 10-4  cm2 V-1  s-1 compared to the nonfluorinated polymer PBDTT. The PSCs based on PBBF:IDIC without extra treatment show a power conversion efficiency (PCE) of 8.5% with a V oc of 0.95 V, a J sc of 15.3 mA cm-2 , and an FF of 58.8%, which is much higher than that of the devices based on PBDTT:IDIC (a PCE of 5.3% with a V oc of 0.88 V, a J sc of 13.7 mA cm-2 , and an FF of 43.9%). These results indicate that PBBF is a promising WBG polymer donor material for the photovoltaic applications in nonfullerene PSCs.

Efficient as-cast semi-transparent organic solar cells with efficiency over 9% and a high average visible transmittance of 27.6.

As promising candidates for future applications in building-integrated photovoltaics, semitransparent organic solar cells (ST-OSCs) have made tremendous progress. However, power conversion efficiency (PCE) of the ST-OSCs is limited by intrinsic narrow absorption spectra concentrated in the near infrared region (NIR), weak extinction coefficient, and mismatched molecular energy levels of thin active layers. Here, an efficient ST-OSC based on a donor/acceptor electron pair of a trifluorinated polymer donor PBFTT and a tetrachlorinated acceptor IT-4Cl was fabricated. Due to halogenation, photovoltaic materials show stronger extinction coefficient, improved crystallinity and higher charge carrier mobility; PBFTT shows lower electronic energy levels, and IT-4Cl shows a red-shifted absorption spectrum. As a result, the PBFTT:IT-4Cl pair shows matched energy levels, complementary absorption spectra in the NIR region and a good blend morphology. Hence, as-cast OSCs based on PBFTT:IT-4Cl achieved a high PCE of 11.1% with a high short-circuit current density of 19.7 mA cm-2 and a high fill factor of 73.9%. Owing to the complementary absorption spectra in the NIR region, high EQE values between 600 and 830 nm and a favourable transparency window between 400 and 600 nm, while the human eye has the highest sensitivity in the yellow-green wavelength region (500-600 nm), ST-OSCs using an ultra-thin (10-20 nm) Au cathode showed high PCEs of 7.9-9.1% at a high average visible transmittance of 37.3-27.6% in the photopic region. The PCE of 9.1% is one of the highest values reported in the literature for ST-OSCs without any extra treatment and with an AVT of more than 25% in the photopic region so far.

Eliminating the Burn-in Loss of Efficiency in Organic Solar Cells by Applying Dimer Acceptors as Supramolecular Stabilizers.

The meta-stable active layer morphology of organic solar cells (OSCs) is identified as the main cause of the rapid burn-in loss of power conversion efficiency (PCE) during long-term device operation. However, effective strategies to eliminate the associated loss mechanisms from the initial stage of device operation are still lacking, especially for high-efficiency material systems. Herein, the introduction of molecularly engineered dimer acceptors with adjustable thermal transition properties into the active layer of OSCs to serve as supramolecular stabilizers for regulating the thermal transitions and optimizing the crystallization of the absorber composites is reported. By establishing intimate π-π interactions with small-molecule acceptors, these stabilizers can effectively reduce the trap-state density (Nt) in the devices to achieve excellent PCEs over 19%. More importantly, the low Nt associated with an initially optimized morphology can be maintained under external stresses to significantly reduce the PCE burn-in loss in devices. This research reveals a judicious approach to improving OPV stability by establishing a comprehensive correlation between material properties, active-layer morphology, and device performance, for developing burn-in-free OSCs.

In Situ Synthesized Low-Dimensional Perovskite for >25% Efficiency Stable MA-Free Perovskite Solar Cells.

Developing an additive to effectively regulate the perovskite crystallization kinetics for the optimized optoelectronic properties of perovskite film plays a vital role in obtaining high efficiency and stable perovskite solar cells (PSCs). Herein, a new additive is designed and directly synthesized in perovskite precursor solution by utilizing an addition reaction between but-3-yn-1-amine hydrochloride (BAH) and formamidinium iodide. It is found that its product may control the intermediate precursor phase for regulating perovskite nucleation, leading to advantageous 2D perovskite to induce growth of perovskite along the preferred [001] orientation with not only released lattice strain but also strong interaction with perovskite to passivate its surface defects. By taking advantage of the above synergistic effects, the optimized PSC delivers an efficiency of 25.19% and a high open-circuit voltage (VOC) of 1.22 V. Additionally, the devices demonstrate good stability, remaining over 90% of their initial efficiencies under ambient atmosphere conditions for 60 days, high temperature of 85 °C for 200 h, or maximum power point tracking for 500 h.

Halogenated Dibenzo[f,h]quinoxaline Units Constructed 2D-Conjugated Guest Acceptors for 19% Efficiency Organic Solar Cells.

Halogenation of Y-series small-molecule acceptors (Y-SMAs) is identified as an effective strategy to optimize photoelectric properties for achieving improved power-conversion-efficiencies (PCEs) in binary organic solar cells (OSCs). However, the effect of different halogenation in the 2D-structured large π-fused core of guest Y-SMAs on ternary OSCs has not yet been systematically studied. Herein, four 2D-conjugated Y-SMAs (X-QTP-4F, including halogen-free H-QTP-4F, chlorinated Cl-QTP-4F, brominated Br-QTP-4F, and iodinated I-QTP-4F) by attaching different halogens into 2D-conjugation extended dibenzo[f,h]quinoxaline core are developed. Among these X-QTP-4F, Cl-QTP-4F has a higher absorption coefficient, optimized molecular crystallinity and packing, suitable cascade energy levels, and complementary absorption with PM6:L8-BO host. Moreover, among ternary PM6:L8-BO:X-QTP-4F blends, PM6:L8-BO:Cl-QTP-4F obtains a more uniform and size-suitable fibrillary network morphology, improved molecular crystallinity and packing, as well as optimized vertical phase distribution, thus boosting charge generation, transport, extraction, and suppressing energy loss of OSCs. Consequently, the PM6:L8-BO:Cl-QTP-4F-based OSCs achieve a 19.0% efficiency, which is among the state-of-the-art OSCs based on 2D-conjugated Y-SMAs and superior to these devices based on PM6:L8-BO host (17.70%) and with guests of H-QTP-4F (18.23%), Br-QTP-4F (18.39%), and I-QTP-4F (17.62%). The work indicates that halogenation in 2D-structured dibenzo[f,h]quinoxaline core of Y-SMAs guests is a promising strategy to gain efficient ternary OSCs.

Unveiling the Morphological and Physical Mechanism of Burn-in Loss Alleviation by Ternary Matrix Toward Stable and Efficient All-Polymer Solar Cells.

All-polymer solar cells (All-PSCs) are considered the most promising candidate in achieving both efficient and stable organic photovoltaic devices, yet the field has rarely presented an in-depth understanding of corresponding device stability while efficiency is continuously boosted via the innovation of polymer acceptors. Herein, a ternary matrix is built for all-PSCs with optimized morphology, improved film ductility and importantly, boosted efficiency and better operational stability than its parental binary counterparts, as a platform to study the underlying mechanism. The target system PQM-Cl:PTQ10:PY-IT (0.8:0.2:1.2) exhibits an alleviated burn-in loss of morphology and efficiency under light soaking, which supports its promoted device lifetime. The comprehensive characterizations of fresh and light-soaked active layers lead to a clear illustration of opposite morphological and physical degradation direction of PQM-Cl and PTQ10, thus resulting in a delicate balance at the optimal ternary system. Specifically, the enlarging tendency of PQM-Cl and shrinking preference of PTQ10 in terms of phase separation leads to a stable morphology in their mixing phase; the hole transfer kinetics of PQM-Cl:PY-IT host is stabilized by incorporating PTQ10. This work succeeds in reaching a deep insight into all-PSC's stability promotion by a rational ternary design, which booms the prospect of gaining high-performance all-PSCs.

Green-Solvent Processed Blade-Coating Organic Solar Cells with an Efficiency Approaching 19% Enabled by Alkyl-Tailored Acceptors.

Power-conversion-efficiencies (PCEs) of organic solar cells (OSCs) in laboratory, normally processed by spin-coating technology with toxic halogenated solvents, have reached over 19%. However, there is usually a marked PCE drop when the blade-coating and/or green-solvents toward large-scale printing are used instead, which hampers the practical development of OSCs. Here, a new series of N-alkyl-tailored small molecule acceptors named YR-SeNF with a same molecular main backbone are developed by combining selenium-fused central-core and naphthalene-fused end-group. Thanks to the N-alkyl engineering, NIR-absorbing YR-SeNF series show different crystallinity, packing patterns, and miscibility with polymeric donor. The studies exhibit that the molecular packing, crystallinity, and vertical distribution of active layer morphologies are well optimized by introducing newly designed guest acceptor associated with tailored N-alkyl chains, providing the improved charge transfer dynamics and stability for the PM6:L8-BO:YR-SeNF-based OSCs. As a result, a record-high PCE approaching 19% is achieved in the blade-coating OSCs fabricated from a green-solvent o-xylene with high-boiling point. Notably, ternary OSCs offer robust operating stability under maximum-power-point tracking and well-keep > 80% of the initial PCEs for even over 400 h. Our alkyl-tailored guest acceptor strategy provides a unique approach to develop green-solvent and blade-coating processed high-efficiency and operating stable OSCs, which paves a way for industrial development.

High-Throughput Screening of Blade-Coated Polymer:Polymer Solar Cells: Solvent Determines Achievable Performance.

Optimization of a new system for organic solar cells is a multiparametric analysis problem that requires substantial efforts in terms of time and resources. The strong microstructure-dependent performance of polymer:polymer cells makes them particularly difficult to optimize, or to translate previous knowledge from spin coating into more scalable techniques. In this work, the photovoltaic performance of blade-coated devices was studied based on the promising polymer:polymer system PBDB-T and PF5-Y5 as donor and acceptor, respectively. Using the recently developed high-throughput methodology, the system was optimized for multiple variables, including solvent system, active layer composition, ratio, and thickness, among others, by fabricating more than 500 devices with less than 24 mg of each component. As a result, the power conversion efficiency of the blade-coated devices varied from 0.08 to 6.43 % in the best device. The performed statistical analysis of the large experimental data obtained showed that solvent selection had the major impact on the final device performance due to its influence on the active layer microstructure. As a conclusion, the use of the plot of the device efficiency in the Hansen space was proposed as a powerful tool to guide solvent selection in organic photovoltaics.

Vinylene-Inserted Asymmetric Polymer Acceptor with Absorption Approaching 1000 nm for Versatile Applications in All-Polymer Solar Cells and Photomultiplication-Type Polymeric Photodetectors.

The emerging polymerized small-molecule acceptors (PSMAs) with near-infrared (NIR) absorption have not only significantly boosted the power conversion efficiencies (PCEs) of all-polymer solar cells (all-PSCs) but have also exhibited great potential for sensitive NIR polymeric photodetectors (PPDs). However, there is no report regarding PSMAs with photo-response that can approach 1000 nm, which is an important criterion for applications in NIR-responsive all-PSCs and PPDs. Herein, by unidirectionally inserting vinylene segments into a selenophene-rich polymer backbone to improve the electron-donating strength and quinoidal character, an asymmetric PSMA, namely, PY3Se-1V, was developed, which showed an extensively red-shifted absorption approaching 1000 nm. The PBDB-T:PY3Se-1V-based binary all-PSCs achieve a decent PCE of 13.2% and a record-high photocurrent density of 25.9 mA cm-2 due to the significantly broadened photo-response and efficient photon-to-electron conversion. More encouragingly, narrowband photomultiplication (PM)-type PPDs based on poly(3-hexylthiophene-2,5-diyl) (P3HT):PY3Se-1V were developed, delivering an exceptionally high external quantum efficiency of 3680% and a responsivity of 28 A W-1 at an NIR peak of 960 nm under -50 V bias, which is reported for the first time in PM-type PPDs with a response approaching 1000 nm.