Determination of the through-plane profile of vanadium species in hydrated Nafion studied with micro X-ray absorption near-edge structure spectroscopy - proof of concept.

Vanadium-ion transport through the polymer membrane results in a significant decrease in the capacity of vanadium redox flow batteries. It is assumed that five vanadium species are involved in this process. Micro X-ray absorption near-edge structure spectroscopy (micro-XANES) is a potent method to study chemical reactions during vanadium transport inside the membrane. In this work, protocols for micro-XANES measurements were developed to enable through-plane characterization of the vanadium species in Nafion 117 on beamline P06 of the PETRA III synchrotron radiation facility (DESY, Hamburg, Germany). A Kapton tube diffusion cell with a diameter of 3 mm was constructed. The tube diameter was chosen in order to accommodate laminar flow for cryogenic cooling while allowing easy handling of the cell components by hand. A vertical step size of 2.5 µm and a horizontal step size of 5 µm provided sufficient resolution to resolve the profile and good statistics after summing up horizontal rows of scan points. The beam was confined in the horizontal plane to account for the waviness of the membrane. The diffusion of vanadium ions during measurement was inhibited by the cryogenic cooling. Vanadium oxidation, e.g. by water radiolysis (water percentage in the hydrated membrane ∼23 wt%), was mitigated by the cryogenic cooling and by minimizing the dwell time per pixel to 5 ms. Thus, the photo-induced oxidation of V3+ in the focused beam could be limited to 10%. In diffusion experiments, Nafion inside the diffusion cell was exposed on one side to V3+ electrolyte and on the other side to VO2+. The ions were allowed to diffuse across the through-plane orientation of the membrane during one of two short defrost times (200 s and 600 s). Subsequent micro-XANES measurements showed the formation of VO2+ from V3+ and VO2+ inside the water body of Nafion. This result proves the suitability of the experimental setup as a powerful tool for the determination of the profile of vanadium species in Nafion and other ionomeric membranes.

A Quartz Crystal Microbalance, Which Tracks Four Overtones in Parallel with a Time Resolution of 10 Milliseconds: Application to Inkjet Printing.

A quartz crystal microbalance (QCM) is described, which simultaneously determines resonance frequency and bandwidth on four different overtones. The time resolution is 10 milliseconds. This fast, multi-overtone QCM is based on multi-frequency lockin amplification. Synchronous interrogation of overtones is needed, when the sample changes quickly and when information on the sample is to be extracted from the comparison between overtones. The application example is thermal inkjet-printing. At impact, the resonance frequencies change over a time shorter than 10 milliseconds. There is a further increase in the contact area, evidenced by an increasing common prefactor to the shifts in frequency, Δf, and half-bandwidth, ΔΓ. The ratio ΔΓ/(-Δf), which quantifies the energy dissipated per time and unit area, decreases with time. Often, there is a fast initial decrease, lasting for about 100 milliseconds, followed by a slower decrease, persisting over the entire drying time (a few seconds). Fitting the overtone dependence of Δf(n) and ΔΓ(n) with power laws, one finds power-law exponents of about 1/2, characteristic of semi-infinite Newtonian liquids. The power-law exponents corresponding to Δf(n) slightly increase with time. The decrease of ΔΓ/(-Δf) and the increase of the exponents are explained by evaporation and formation of a solid film at the resonator surface.

CE-XRF-initial steps toward a non-invasive elemental sensitive detector for liquid separations.

The toxicity, bioavailability, and mobilization of elements within the biosphere is dependent on its species. CE has emerged as a strong separation technique for elemental speciation. Conventionally, CE has been coupled with UV-vis, C4 D, PIXE (proton-induced X-ray emission), and ICP-MS. UV-vis and C4 D are not elemental sensitive detection methods, PIXE requires the etching of the detection window resulting in a very brittle capillary, and ICP-MS is an expensive large footprint instrument. Here, we aim to develop an elemental specific detector, XRF (X-ray fluorescence spectrometry), for use with CE. A custom-built micro-XRF was tested and static LODs were determined for 19 elements (Ca-U) with both unmodified (20-926 ppm) and modified capillaries (20-291 ppm). A custom-built CE was combined with the micro-XRF and separation of Ca2+ and Co2+ was obtained. Sr2+ coeluted with Ca2+ in the mixture, but because of the elemental sensitivity of XRF, the Sr and Ca signals could be separated. After successful testing of the micro-XRF, the feasibility of using a low-cost X-ray source and detector was tested. Even lower LODs were obtained for Ga and Rb, showing the feasibility of a smaller, low-cost XRF unit as an elemental specific detector. However, the buffer selection that can be conveniently used with XRF is currently limited due to capillary corrosion, likely correlated to radiolysis.

Total reflection X-ray fluorescence analysis of airborne silver nanoparticles from fabrics.

Ag nanoparticles (NPs) are usually applied to consumer products because of their antimicrobial properties, which are desired in fabrics for sportswear as well as cloth used for cleaning. Hazards to human health from airborne Ag NPs may occur when the NPs are inhaled. NPs are comparable in size to macromolecules and viruses and able to penetrate deep into the lungs, e.g., the alveoli, where they may cause damage to cells and tissue due to their large surface area. In this study, aerosols released form fabrics treated with Ag NPs were collected using a low pressure Berner impactor and analyzed with total reflection X-ray fluorescence (TXRF). We found that the Ag NPs are released primarily in the form of larger particles, mainly 0.13-2 µm, probably attached to fiber material. Using an electron micro probe, single particles could be identified. The detection of backscattered electrons suggests small spots on the particle consist of a heavier element, which most likely is Ag, although the signal in energy-dispersive X-ray spectroscopy (EDX) was below the lower limit of detection (LOD). To achieve LODs necessary for Ag determination, Ar peaks were eliminated by a nitrogen atmosphere provided by the "Picofox-box". This enables linear calibration and quantification of Ag. The LOD was calculated at 0.2 ng (2.0 ppb). Following the TXRF and scanning electron microscopy (SEM)/EDX analysis, the aerosol samples were dissolved in nitric acid and analyzed with ICPMS to successfully confirm the results obtained by the TXRF measurements.

Engineering Compounds for the Recovery of Critical Elements from Slags: Melt Characteristics of Li5AlO4, LiAlO2, and LiAl5O8.

Engineered artificial minerals (EnAMs) are the core of a new concept of designing scavenger compounds for the recovery of critical elements from slags. It requires a fundamental understanding of solidification from complex oxide melts. Ion diffusivity and viscosity play vital roles in this process. In the melt, phase separations and ion transport give rise to gradients/increments in composition and, with it, to ion diffusivity, temperature, and viscosity. Due to this complexity, solidification phenomena are yet not well understood. If the melt is understood as increments of simple composition on a microscopic level, then the properties of these are more easily accessible from models and experiments. Here, we obtain these data for three stoichiometric lithium aluminum oxides. LiAlO2 is a promising EnAM for the recovery of lithium from lithium-ion battery pyrometallurgical processing. It is obtained through the addition of aluminum to the recycling slag melt. The high temperature properties spanning from below to above the liquidus temperature of three stoichiometric Li-Al-Oxides: Li5AlO4, LiAlO2, and LiAl5O8 are determined using molecular dynamic simulations. The compounds are also synthesized via the sol-gel route. The Li+ ion exhibits the largest diffusivity. They are quite mobile already below the liquidus temperature, i.e., for LiAlO2 at T = 1700 K, the diffusion coefficient of the lithium ion equals D = 3.0 × 10-9 m2 s-1. The other ions Al3+ and O2- do not move considerably at that temperature. The diffusivity of Li+ is largest in the lithium-rich compound Li5AlO4 with D = 32 × 10-9 m2 s-1 at 2500 K. The lower the viscosity, the higher the lithium content. The Li5AlO4 exhibits a viscosity of η = 2.2 mPa s at 1328 K which matches well with the experimentally determined 2.5 mPa s at this temperature. The viscosity of LiAlO2 at 1800 K is more than two times higher. These data sets can help to describe the melts on a microscopic level and understand how the melt properties will change due to gradients in the Li/Al concentration.

Photo-switchable Collectors for the Flotation of Lithium Aluminate for the Recycling of the Critical Raw Material Lithium.

Flotation of the mineral lithium aluminate by application of the natural product punicine from Punica granatum and some derivatives as collectors is examined. Punicines, 1-(2',5'-dihydroxyphenyl)-pyridinium compounds, are switchable molecules whose properties can be changed reversibly. They exist as cations, neutral mesomeric betaines, anions, and dianions depending on the pH. In light, they form radicals. Five punicine derivatives were prepared which possess ß-methyl, ß-chlorine, γ-tert.-butyl, and γ-acetyl groups attached to the pyridinium ring, and a pyrogallol derivative. On the other hand, LiAlO2 reacts with water to give species such as LiAl2(OH)7 on its surface. Flotations were performed applying the punicines in daylight (3000 lux), in darkness (<40 lux) and under UV-irradiation (4500 lux, 390-400 nm). The pH of the suspension, the collector's concentration, the conditioning time as well as the flotation time were varied. The recovery rates strongly depend on these parameters. For example, the recovery rate of lithium aluminate was increased by 116 % on changing the lighting condition from daylight to darkness, when the pyrogallol derivative of punicine was applied. UV, FTIR, TGA and zeta potential measurements as well as DFT calculations were performed in order to gain insight into the chemistry of punicines on the surface of LiAlO2 and LiAl2(OH)7 in water which influence the flotation's results.

Lithium aluminate flotation by pH- and light-switchable collectors based on the natural product punicine.

Derivatives of the natural product punicine [1-(2',5'-dihydroxyphenyl)pyridinium chloride] were developed as switchable collectors for the flotation of lithium-containing engineered artifical minerals (EnAMs). These EnAMs are e.g. formed by pyrometallurgical processing of end-of-life lithium-ion batteries. Depending on the pH value and the lighting conditions, punicines exist in water as cations, two different electrostatically neutral mesomeric betaines, anionic tripoles, radical cations or radical anions. The radical species form by photochemically induced disproportionation reactions. We prepared punicine derivatives introducing alkyl chains in the pyridinium moiety (4-methyl, 4-ethyl, 4-octyl and 4-undecanyl) to install hydrophobic groups and examined the recovery rates of the flotation of lithium aluminate (LiAlO2). We varied the lighting conditions (darkness, daylight, LED irradiation at λ = 390-400 nm) and the pH value, the collector's and frother's concentration, and the flotation time. With our collectors, recovery rates of lithium aluminate up to 90% were accomplished when the flotation was conducted in Hallimond tubes exposed to daylight at pH 11 in water.

In situ functionalization and PEO coating of iron oxide nanocrystals using seeded emulsion polymerization.

Herein we demonstrate that seeded emulsion polymerization is a powerful tool to produce multiply functionalized PEO coated iron oxide nanocrystals. Advantageously, by simple addition of functional surfactants, functional monomers, or functional polymerizable linkers-solely or in combinations thereof-during the seeded emulsion polymerization process, a broad range of in situ functionalized polymer-coated iron oxide nanocrystals were obtained. This was demonstrated by purposeful modulation of the zeta potential of encapsulated iron oxide nanocrystals and conjugation of a dyestuff. Successful functionalization was unequivocally proven by TXRF. Furthermore, the spatial position of the functional groups can be controlled by choosing the appropriate spacers. In conclusion, this methodology is highly amenable for combinatorial strategies and will spur rapid expedited synthesis and purposeful optimization of a broad scope of nanocrystals.

Indoor aerosol determination with respect to a soiling phenomenon in private residences.

Indoor aerosol exposure has become of major interest since health hazards arising from fine and ultrafine dust particles have become more evident. The study presented here is dedicated to fine and ultrafine dust characterization and determination in more than 150 private residences with special respect to a phenomenon of enhanced soiling. In the scientific community committed to ecological housing and building it is referred to as "black magic dust" though the staining is often film-like in nature. This phenomenon has been observed for 20 years in residences in Europe and North America and there is strong evidence that it is correlated to emission of semivolatile organic compounds (SVOCs) from refurbishing materials. In this study we show that fine dust particle concentrations are elevated in such homes and that there is characteristic particle morphology for "black magic dust" staining. From the results we suggest that elevated particle concentration and particle size are significant to induce a condensation process which causes the observed blackening. Reduced air exchanges due to new insulation standards may also contribute to its occurrence.

Polyether-tethered imidazole-2-thiones, imidazole-2-selenones and imidazolium salts as collectors for the flotation of lithium aluminate and spodumene.

Imidazolium salts were prepared which possess 2-ethoxyethyl pivalate or 2-(2-ethoxyethoxy)ethyl pivalate groups as amphiphilic side chains with oxygen donors as well as n-butyl substituents as hydrophobic groups. The N-heterocyclic carbenes of the salts, characterized by 7Li and 13C NMR spectroscopy as well as by Rh and Ir complex formation, were used as starting materials for the preparation of the corresponding imidazole-2-thiones and imidazole-2-selenones. Flotation experiments in Hallimond tubes under variation of the air flow, pH, concentration and flotation time were performed. The title compounds proved to be suitable collectors for the flotation of lithium aluminate and spodumene for lithium recovery. Recovery rates up to 88.9% were obtained when the imidazole-2-thione was used as collector.

Confocal MXRF in environmental applications.

In this review we highlight the performance of confocal micro X-ray fluorescence (CMXRF) for application in environmental science, citing contributions from recent studies (2008-2010). In CMXRF the use of focusing and collecting optics enables discrimination of the origin of fluorescence photons in three dimensions. It thereby enables simple and direct three dimensional imaging, and also the removal of unwanted signal contribution either from the depth of the sample or from its surface. By limiting the area of origin of fluorescence signal CMXRF can simplify quantitative approaches.

Characterization of Dimeric Vanadium Uptake and Species in Nafion™ and Novel Membranes from Vanadium Redox Flow Batteries Electrolytes.

A core component of energy storage systems like vanadium redox flow batteries (VRFB) is the polymer electrolyte membrane (PEM). In this work, the frequently used perfluorosulfonic-acid (PFSA) membrane Nafion™ 117 and a novel poly (vinylidene difluoride) (PVDF)-based membrane are investigated. A well-known problem in VRFBs is the vanadium permeation through the membrane. The consequence of this so-called vanadium crossover is a severe loss of capacity. For a better understanding of vanadium transport in membranes, the uptake of vanadium ions from electrolytes containing Vdimer(IV-V) and for comparison also V(II), V(III), V(IV), and V(V) by both membranes was studied. UV/VIS spectroscopy, X-ray absorption near edge structure spectroscopy (XANES), total reflection X-ray fluorescence spectroscopy (TXRF), inductively coupled plasma optical emission spectrometry (ICP-OES), and micro X-ray fluorescence spectroscopy (microXRF) were used to determine the vanadium concentrations and the species inside the membrane. The results strongly support that Vdimer(IV-V), a dimer formed from V(IV) and V(V), enters the nanoscopic water-body of Nafion™ 117 as such. This is interesting, because as of now, only the individual ions V(IV) and V(V) were considered to be transported through the membrane. Additionally, it was found that the Vdimer(IV-V) dimer partly dissociates to the individual ions in the novel PVDF-based membrane. The Vdimer(IV-V) dimer concentration in Nafion™ was determined and compared to those of the other species. After three days of equilibration time, the concentration of the dimer is the lowest compared to the monomeric vanadium species. The concentration of vanadium in terms of the relative uptake λ = n(V)/n(SO3) are as follows: V(II) [λ = 0.155] > V(III) [λ = 0.137] > V(IV) [λ = 0.124] > V(V) [λ = 0.053] > Vdimer(IV-V) [λ = 0.039]. The results show that the Vdimer(IV-V) dimer needs to be considered in addition to the other monomeric species to properly describe the transport of vanadium through Nafion™ in VRFBs.

Picoliter droplet deposition using a prototype picoliter pipette: control parameters and application in micro X-ray fluorescence.

In this study, we introduce a Hewlett-Packard prototype picoliter pipette, the "thermal inkjet picofluidic system" (TIPS), for analytical purposes. In contrast to the use of actual inkjet printers, this instrument allows for control of all energy and time settings. We are able to show that in contrast to techniques delivering microliter and nanoliter volumes, evaporation has a major influence on the deposition of picoliter volumes and has to be treated seriously when picoliter depositions are applied in the laboratory for calibration purposes. We developed a strategy to reduce evaporation by varying different parameters, thereby achieving a precision of less than 10% for elemental depositions ranging from 1 to 300 picoliters and 1 to 2000 pg elemental deposits. Additionally, we determined the performance of the micro X-ray fluorescence (MXRF) instruments in terms of limit of detection (LODs), focal spot size, sensitivity, and precision and evaluated the TIPS deposits as reference materials for MXRF using single and multielement solutions. A linear response was observed with correlation coefficients from 0.991 to 0.999 for elemental deposits on AP1 film, and there was a standard deviation from 1 to 40%, depending on the element and the mass deposited. LOD's for Ni deposits on AP1 films were found to range from low picogram levels to subpicogram levels. The dried deposits were characterized for size and shape using light microscopy and atomic force microscopy (AFM) to estimate matrix effects and the area covered with sample material for the MXRF analysis. Diameters from 14 to 39 microm and thicknesses from 200 nm to 2 microm were measured. The accuracy of the dried spot approach was demonstrated by comparing multielement deposits from the TIPS with the NIST SRMs 1833 and 1832 thin film standards for MXRF analysis. The deviation from the SRMs was found to be better than 10%.

A road map to assess critical materials content in boron industrial wastes using sustainable micro-X-ray fluorescence and total reflection X-ray fluorescence instrumentation.

Turkey is the leading country in the world in terms of boron production and sale. Increasing boron production goes along with an increasing generation of boron wastes. The pollution of the soil and the air around the waste piles, as well as the occupation of several square kilometers of ground, are major environmental problems. It is, therefore, very important to make use of the wastes to both protect the environment and create revenue. This work presenteda road map for fast screening of boron waste for critical elements followed by determination of the elements using small footprint low power instrumentation. The sample preparation was kept to a minimum. A procedure that allowed an assessment of critical materials in industrial production waste with minimal consumption of hazardous acids, energy, and time was presented. The samples were first screened for valuable and hazardous elements by micro-X-ray fluorescence (XRF). Samples with considerable contents of Cs, Rb, and Aswere then prepared as slurries for the total reflection XRF (TXRF) measurement. To evaluate the TXRF procedure, a standard reference material was analyzed. As a result, Rb and Cs in concentrations up to 420 ± 70 and 1500 ± 200 mg/kg were detected in some of the waste forms. The time savings were in order of a factor of 3 when comparing the prescreening combined micro-XRF and TXRF approach to an all TXRFanalysis approach.

Side effects of a non-peroxide-based home bleaching agent on dental enamel.

Changes in the chemistry and structure of enamel due to a non-peroxide-based home bleaching product (Rapid White) were studied in vitro using attenuated total reflectance-infrared spectroscopy, Raman spectroscopy, electron probe microanalysis, flame atomic absorption spectroscopy, and total reflection X-ray fluorescence. The results revealed that the citric-acid-containing gel-like component of the bleaching system substantially impacts on the dental hard tissue. Enamel is affected on several levels: (i) the organic component is removed from superficial and deeper enamel layers and remnants of the bleaching gel are embedded in the emptied voids; (ii) cracks and chemical inhomogeneities with respect to Ca and P occur on the surface; and (iii) within a submicron layer of enamel, the Ca-O bond strength in apatite decreases, thus enhancing calcium leakage from the bleached enamel hard tissue.

Characteristics of picoliter droplet dried residues as standards for direct analysis techniques.

The characteristics of dried residues of picodroplets of single-, two-, and three-element aqueous solutions, which qualify these as reference materials in the direct analysis of single particles, single cells, and other microscopic objects using, e.g., laser ablation inductively coupled plasma time-of-flight mass spectrometry (LA-ICP-TOF-MS) and micro-X-ray fluorescence (MXRF), were evaluated. Different single-, two-, and three-element solutions (0.01-1 g/L) were prepared in picoliter volume (around 130 pL) with a thermal inkjet printing technique. An achievable dosing precision of 4-15% was calculated by total reflection X-ray fluorescence (TXRF) determination of the transferred elemental mass of an array of 100 droplets. The size of the dried residues was determined by optical microscopy to be 5-20 microm in diameter depending on the concentration and the surface material. The elemental distribution of the dried residues was determined with synchrotron micro-X-ray fluorescence (SR-MXRF) analyses. The MXRF results show high uniformity for element deposition of every single droplet with an RSTD of 4-6% depending on the concentration of spotted solution. The shape and height profile of dried residues from picoliter droplets were studied using atomic force microscopy (AFM). It was found that these dry to give symmetrical spherical segments with maximum heights of 1.7 microm. The potential of this technique for direct LA-ICP-TOF-MS analysis is shown.

Structural characterization of beta-sheeted oligomers formed on the pathway of oxidative prion protein aggregation in vitro.

The pathology of transmissible spongiform encephalopathies (TSEs) is strongly associated with the structural conversion of the cellular prion protein (PrPC) into a misfolded isoform (PrPSc) that assembles into amyloid fibrils. Since increased levels of oxidative stress have been linked to prion diseases, we investigated the metal-induced oxidation of human PrP (90-231). A novel in vitro conversion assay based on aerobic incubation of PrP in the presence of elemental copper pellets at pH 5 was established, resulting in aggregation of highly beta-sheeted prion proteins. We show for the first time that two discrete oligomeric species of elongated shape, approx. 25 mers and 100 mers, are formed on the pathway of oxidative PrP aggregation in vitro, which are well characterized regarding shape and size using small-angle X-ray scattering (SAXS), dynamic light scattering (DLS), and electron microscopy (EM). Considering that small oligomers of highly similar size have recently been reported to show the highest specific infectivity within TSE-infected brain tissues of hamsters, the novel oligomers observed in this study are interesting candidates as agent causing neurodegenerative and/or self-propagating effects. Moreover, our results significantly strengthen the theory that oxidative stress might be an influence that leads to substantial structural conversions of PrP in vivo.

Direct analysis of Al2O3 powders by total reflection X-ray fluorescence spectrometry.

A direct analysis procedure for the determination of trace impurities of Ca, V, Cr, Mn, Fe, Ni, Cu, Zn and Ga in Al2O3 ceramic powders by total reflection X-ray fluorescence spectrometry (TXRF) is described. The powders were analysed in the form of slurries containing 1-10 mg mL(-1) of powder. The use of the procedure in the case of powders with differing grain size and for different slurry concentrations was investigated. Three different quantification possibilities were compared, namely the use of Al as a matrix component, the use of Fe as a trace element contained in the sample or of Co added in concentrations of 200 microg g(-1) as internal standard. The homogeneity of elemental distributions in sample layers deposited on the TXRF quartz carriers by evaporating 5 microL of the 10 mg mL(-1) slurries was studied by scanning the 4- to 5-mm-diameter spots of two samples by synchrotron radiation TXRF at Hasylab. For powders with differing graininess but mainly finer than about a few 10 microm, no systematic influence of the grain size on the accuracy of the determinations of Ca, V, Fe, Ni, Cu and Zn could be observed. The measurement precision, however, seemed to be limited by inhomogeneous distributions of the trace elements in the samples as testified by the synchrotron radiation TXRF scans. Detection limits of the developed TXRF procedure for Ca, V, Cr, Mn, Fe, Ni, Cu, Zn and Ga were found to be in the 0.3-7 microg g(-1) range and were shown to increase slightly with the grain size of the samples. Quantification using Al (matrix) as internal standard led to systematically higher values out of the accuracy required, whereas the other two approaches in all cases led to reliable results.