RESUMO
The problem of water pollution is of a great concern. Adsorption is one of the most efficient techniques for removing noxious heavy metals from the solvent phase. This paper presents a detailed information and review on the adsorption of noxious heavy metal ions from wastewater effluents using various adsorbents - i.e., conventional (activated carbons, zeolites, clays, biosorbents, and industrial by-products) and nanostructured (fullerenes, carbon nanotubes, graphenes). In addition to this, the efficiency of developed materials for adsorption of the heavy metals is discussed in detail along with the comparison of their maximum adsorption capacity in tabular form. A special focus is made on the perspectives of further wider applications of nanostructured adsorbents (especially, carbon nanotubes and graphenes) in wastewater treatment.
Assuntos
Metais Pesados/análise , Nanotubos de Carbono/química , Águas Residuárias/química , Poluentes Químicos da Água/análise , Purificação da Água/métodos , Adsorção , Carvão Vegetal/química , Íons , Zeolitas/químicaRESUMO
The paper considers the development of fillers representing mixtures of carbon nanotubes and graphene materials (graphene oxide and graphene nanoplatelets) in different mass ratios to modify epoxy resin. The graphene type and content effect on the dispersed phase particle effective sizes-both in aqueous suspensions and the resin-was analyzed. Hybrid particles were characterized by Raman spectroscopy and electron microscopy. The composites containing 0.15-1.00 wt.% CNTs/GO and CNTs/GNPs were thermogravimetrically analyzed, and their mechanical characteristics were determined. SEM images of the composite fracture surfaces were acquired. Optimal dispersions containing 75-100 nm particles were obtained at the CNTs:GO mass ratio of 1:4. It was shown that the CNTs can be located between the GO layers and on the GNP surface. The samples containing up to 0.2 wt.% CNTs/GO (at 1:1 and 1:4 ratios) were stable when heated in air up to 300 °C. For 0.15-0.20 wt.% CNTs/GO (at 1:1 ratio), the tensile strength and modulus of the composite increased by 84-88 and 40%, respectively. The increase in the strength characteristics was found to occur due to the interaction of the filler layered structure with the polymer matrix. The obtained composites can be used as structural materials in different fields of engineering.
RESUMO
This paper considers the synthesis of a novel nanocomposite based on reduced graphene oxide and oxidized carbon nanotubes modified with polyaniline and phenol-formaldehyde resin and developed through the carbonization of a pristine aerogel. It was tested as an efficient adsorbent to purify aquatic media from toxic Pb(II). Diagnostic assessment of the samples was carried out through X-ray diffractometry, Raman spectroscopy, thermogravimetry, scanning and transmission electron microscopy, and infrared spectroscopy. The carbonized aerogel was found to preserve the carbon framework structure. The sample porosity was estimated through nitrogen adsorption at 77 K. It was found that the carbonized aerogel predominantly represented a mesoporous material having a specific surface area of 315 m2/g. After carbonization, an increase in smaller micropores occurred. According to the electron images, the highly porous structure of the carbonized composite was preserved. The adsorption capacity of the carbonized material was studied for liquid-phase Pb(II) extraction in static mode. The experiment results showed that the maximum Pb(II) adsorption capacity of the carbonized aerogel was 185 mg/g (at pH 6.0). The results of the desorption studies showed a very low desorption rate (0.3%) at pH 6.5 and a rate of about 40% in a strongly acidic medium.
RESUMO
A hapten-protein conjugate with copper nanoparticles (Hap-Car-BSA@CuNPs) was first synthesized in the present work for the determination of carbaryl. The copper nanoparticles (CuNPs) of the conjugate were used as electrochemical labels in the direct solid-phase competitive determination of carbaryl residues in flour from different crops. The signal was read by linear sweep anodic stripping voltammetry (LSASV) of copper (through the electrochemical stripping of accumulated elemental copper) on a gold-graphite electrode (GGE). To form a recognition receptor layer of monoclonal antibodies against the carbaryl on the surface of the GGE, 1-ethyl-3-(3-dimethylaminopropyl)carbodiimide hydrochloride (EDC) and 1-hydroxy-2,5-pyrrolidinedione (NHS) were used as the best covalent cross-linkers. The concentrations of the antibodies and the Hap-Car-BSA@CuNPs conjugate were optimized for carbaryl detection by the electrochemical immunosensor. The electrochemical immunosensor can be used for highly sensitive determination of carbaryl residues in flour samples in the concentration range 0.8-32.3 µg·kg-1, with a limit of detection 0.08 µg·kg-1. The present work paves the path for a novel method for monitoring carbaryl in other food products, drinks, and soil samples.