Capacitive Photodetector Thin-Film Cells of Cu-As2S3-Cu as Revealed by Dielectric Spectroscopy.

The As2S3-Cu interface was studied by dielectric spectroscopy measurements on Cu-As2S3-Cu thin film heterostructure samples to assess the charge carriers' contribution to the electrical properties of such an interface. Three-dimensional printed masks ensured good reproducibility during the PLD deposition of heterostructure samples. The samples were tested for electrical conductivity and AC photoconductivity by dielectric spectroscopy measurements. DC bias voltages and light were applied to the samples. The electrical capacity of the thin film heterostructure can be modified electrically and optically. We observed long-term photoconductivity with a time dependency that was not exponential, and a quick change of the electrical capacity, indicating the potential of the heterostructure cells as photodetector candidates.

Degradation of Losartan Potassium Highlighted by Correlated Studies of Photoluminescence, Infrared Absorption Spectroscopy and Dielectric Spectroscopy.

In this paper, new results on the degradation of losartan potassium (LP, (1)), in the absence and presence of excipients, which was induced by UV light, the acid character of phosphate buffer solution (PBS) and alkaline medium, respectively, are reported through correlated studies of FTIR spectroscopy, photoluminescence and dielectric spectroscopy. The photoluminescence (PL) spectra of LP and the drug marked under the name Lorista (LO) are characterized by intense emission bands, peaking at 378 nm and 380 nm, respectively, accompanied by low intensity bands with a maximum at ~450-460 nm. Photodegradation of LO in a solid state is evidenced by a decrease in the intensity of the PL band at 380 nm, a variation that originates both in the adsorption of water vapors from the air and in the interaction of LP with excipients such as cornstarch, silicon dioxide and cellulose. The LP-water interaction is described, taking into account the main electrical parameters, i.e., complex dielectric permittivity and electrical conductivity. Photodegradation of LP and LO also induces an increase in the intensity of the emission band, at ~450-460 nm. The influence of acid and alkaline medium on the LO degradation is analyzed using phosphate buffer (PBS) and NaOH solutions, respectively. In both cases, a decrease in the intensity of the PL band, at 380 nm, is reported. The intensity diminution of the PL spectra of NaOH-reacted LP and LO is the result of the formation of the photodegradation product N-methanolamide-{[2'-(1H-tetrazol-5-yl)(1,1'-biphenyl)-4-yl]methyl} (2). This compound was proven by the studies of FTIR spectroscopy achieved on LP and NaOH-reacted LP. The appearance of the IR band at 1740 cm-1 and the increase in the absorbance in the IR band at 1423 cm-1 indicate that the photodegradation product (2) contains the C=O and C-OH functional groups.

The Influence of the Ceramic Nanoparticles on the Thermoplastic Polymers Matrix: Their Structural, Optical, and Conductive Properties.

This paper prepared composites under the free membranes form that are based on thermoplastic polymers of the type of polyurethane (TPU) and polyolefin (TPO), which are blended in the weight ratio of 2:1, and ceramic nanoparticles (CNs) such as BaSrTiO3 and SrTiO3. The structural, optical, and conductive properties of these new composite materials are reported. The X-ray diffraction studies highlight a cubic crystalline structure of these CNs. The main variations in the vibrational properties of the TPU:TPO blend induced by CNs consist of the following: (i) the increase in the intensity of the Raman line of 1616 cm-1; (ii) the down-shift of the IR band from 800 to 791 cm-1; (iii) the change of the ratio between the absorbance of IR bands localized in the spectral range 950-1200 cm-1; and (iv) the decrease in the absorbance of the IR band from 1221 cm-1. All these variations were correlated with a preferential adsorption of thermoplastic polymers on the CNs surface. A photoluminescence (PL) quenching process of thermoplastic polymers is demonstrated to occur in the presence of CNs. The anisotropic PL measurements have highlighted a change in the angle of the binding of the TPU:TPO blend, which varies from 23.7° to ≈49.3° and ≈53.4°, when the concentration of BaSrTiO3 and SrTiO3 CNs, respectively, is changed from 0 to 25 wt. %. Using dielectric spectroscopy, two mechanisms are invoked to take place in the case of the composites based on TPU:TPO blends and CNs, i.e., one regarding the type of the electrical conduction and another specifying the dielectric-dipolar relaxation processes.

Lead-Free BNT-BT0.08/CoFe2O4 Core-Shell Nanostructures with Potential Multifunctional Applications.

Herein we report on novel multiferroic core-shell nanostructures of cobalt ferrite (CoFe2O4)-bismuth, sodium titanate doped with barium titanate (BNT-BT0.08), prepared by a two-step wet chemical procedure, using the sol-gel technique. The fraction of CoFe2O4 was varied from 1:0.5 to 1:1.5 = BNT-BT0.08/CoFe2O4 (molar ratio). X-ray diffraction confirmed the presence of both the spinel CoFe2O4 and the perovskite Bi0.5Na0.5TiO3 phases. Scanning electron microscopy analysis indicated that the diameter of the core-shell nanoparticles was between 15 and 40 nm. Transmission electron microscopy data showed two-phase composite nanostructures consisting of a BNT-BT0.08 core surrounded by a CoFe2O4 shell with an average thickness of 4-7 nm. Cole-Cole plots reveal the presence of grains and grain boundary effects in the BNT-BT0.08/CoFe2O4 composite. Moreover, the values of the dc conductivity were found to increase with the amount of CoFe2O4 semiconductive phase. Both X-ray photoelectron spectroscopy (XPS) and Mössbauer measurements have shown no change in the valence of the Fe3+, Co2+, Bi3+ and Ti4+ cations. This study provides a detailed insight into the magnetoelectric coupling of the multiferroic BNT-BT0.08/CoFe2O4 core-shell composite potentially suitable for magnetoelectric applications.

Flexible Delivery Patch Systems based on Thermoresponsive Hydrogels and Submicronic Fiber Heaters.

This paper proposes a novel, flexible, low cost administration patch which could be used as a non-invasive, controlled transdermal drug delivery system. The fabricated device consists in a flexible microfiber architecture heater covered with a thermoresponsive hydrogel, namely poly(N-isopropylacrylamide), as a matrix for the incorporation of active molecules. The manufacturing process consists of two main steps. First, the electrospun poly(methyl methacrylate) fiber networks are sputter coated with a thin gold layer and attached to flexible poly(ethylene terephthalate) substrates to obtain the heating platforms. Second, the heaters are encapsulated in poly(ethylene terephthalate) foils and covered with poly(N-isopropylacrylamide) hydrogel sheets. In order to illustrate the functionality of the fabricated patch, the hydrogel layer is loaded with methylene blue aqueous solution and is afterwards heated via Joule effect, by applying a voltage on the metalized fibers. The methylene blue releasing profiles of the heated patch are compared with those of the unheated one and the influence of parameters such as hydrogel composition and morphology, as well as the applied voltage values for microheating are investigated. The results indicate that the fabricated patch can be used as a drug administration instrument, while its performance can be tuned depending on the targeted application.

Involvement of cyan and ester groups in surface interactions of aerosil-cyanophenyl alkyl benzoate systems with high silica density: Infrared investigations.

Composites prepared from aerosil A380 and liquid crystals (LCs) of 4-n-alkyl-4'-cyanophenyl benzoate type, with four to six carbon atoms in the alkyl chain were investigated by infrared spectroscopy. Their high silica content (of 2-7 g aerosil/1 g of LC) was given by thermogravimetric investigations and allows the observation of a rather thin LC layer on the silica particles. Several surface species onto the external surface of the grains were demonstrated. Arguments are given that monomer and dimer species are present in the bulk cyanophenyl benzoate materials while bulk-like species along with hydrogen-bonded ones coexist in the so-called surface layer of the composites. The main interaction of LC molecules with the aerosil surface is by hydrogen bonding taking place with the involvement of the cyan group. There is a contribution of ester carbonyl group to these surface interactions but this cannot be well quantified.

Molecular relaxation processes in a MOF-5 structure revealed by broadband dielectric spectroscopy: signature of phenylene ring fluctuations.

The molecular mobility of a MOF-5 metal-organic framework was investigated by broadband dielectric spectroscopy. Three relaxation processes were revealed. The temperature dependence of their relaxation rates follows an Arrhenius law. The process observed at lower temperatures is attributed to bending fluctuations of the edges of the cages involving the Zn-O clusters. The processes ("region II") at higher temperatures were assigned to fluctuations of phenyl rings in agreement with the NMR data found by Gould et al. (J. Am. Chem. Soc. 2008, 130, 3246). The carboxylate groups might also be involved. The rotational fluctuations of the phenyl rings leading to the low frequency part of relaxation region II might be hindered either by some solvent molecules entrapped in the cages or by an interpenetrated structure and have a broad distribution of activation energies. The high frequency part of region II corresponds nearly to a Debye-like process: This is explained by a well-defined structure of empty pores.