Optimization of Electrode and Cell Design for Ultrafast-Charging Lithium-Ion Batteries Based on Molybdenum Niobium Oxide Anodes.

Niobium oxides are an emerging class of anode materials for use in high-power lithium-ion batteries. Galvanostatic cycling and electrochemical impedance spectroscopy (EIS) were used in this study to investigate the influence of electrode porosity, electrode mass ratio, and cycling rate on the capacity, cycle life, and ionic conductivity of Li-ion battery cells based on a modified micron-sized MoNb12O33 (MNO) anode powder. Both electrode and cell designs were found to have a significant impact on the rate performance and cycle life of Li-ion half- and full cells. A higher specific capacity, improved rate performance, and a longer cycle life were obtained in both anode and cathode half-cells by lowering the electrode porosity through calendaring. MNO/Li half-coin cells displayed excellent cyclability, reaching 80% state of health (SOH) after 600 cycles at C/2 charge and 1C discharge. MNO/NMC622 full-coin cells displayed a high capacity of 179 mAh g-1 at 100 mA g-1 (0.5 mA cm-2) and excellent cyclability at 25 °C, reaching 70% SOH after over 1000 cycles at 1 mA cm-2 after optimizing their N/P ratio. Excellent cyclability was obtained at both 1C/1C and fast 2C/2C cycling, reaching 80% SOH after 700 and 470 cycles, respectively. Full-coin and small pouch cells had outstanding rate performance as they could be charged from 0 to 84% capacity in less than 5 min at 10 mA cm-2 and to 70% SOC in 120 s at 20 mA cm-2.

High-Voltage Stabilization of O3-Type Layered Oxide for Sodium-Ion Batteries by Simultaneous Tin Dual Modification.

O3-type layered oxide materials are considered to be a highly suitable cathode for sodium-ion batteries (NIBs) due to their appreciable specific capacity and energy density. However, rapid capacity fading caused by serious structural changes and interfacial degradation hampers their use. A novel Sn-modified O3-type layered NaNi1/3Fe1/3Mn1/3O2 cathode is presented, with improved high-voltage stability through simultaneous bulk Sn doping and surface coating in a scalable one-step process. The bulk substitution of Sn4+ stabilizes the crystal structure by alleviating the irreversible phase transition and lattice structure degradation and increases the observed average voltage. In the meantime, the nanolayer Sn/Na/O composite on the surface effectively inhibits surface parasitic reactions and improves the interfacial stability during cycling. A series of Sn-modified materials are reported. An 8%-Sn-modified NaNi1/3Fe1/3Mn1/3O2 cathode exhibits a doubling in capacity retention increase after 150 cycles in the wide voltage range of 2.0-4.1 V vs Na/Na+ compared to none, and 81% capacity retention is observed after 200 cycles in a full cell vs hard carbon. This work offers a facile process to simultaneously stabilize the bulk structure and interface for the O3-type layered cathodes for sodium-ion batteries and raises the possibility of similar effective strategies to be employed for other energy storage materials.

Reclaimed and Up-Cycled Cathodes for Lithium-Ion Batteries.

As electric vehicles become more widely used, there is a higher demand for lithium-ion batteries (LIBs) and hence a greater incentive to find better ways to recycle these at their end-of-life (EOL). This work focuses on the process of reclamation and re-use of cathode material from LIBs. Black mass containing mixed LiMn2O4 and Ni0.8Co0.15Al0.05O2 from a Nissan Leaf pouch cell are recovered via two different recycling routes, shredding or disassembly. The waste material stream purity is compared for both processes, less aluminium and copper impurities are present in the disassembled waste stream. The reclaimed black mass is further treated to reclaim the transition metals in a salt solution, Ni, Mn, Co ratios are adjusted in order to synthesize an upcycled cathode, LiNi0.6Mn0.2Co0.2O2 via a co-precipitation method. The two reclamation processes (disassembly and shredding) are evaluated based on the purity of the reclaimed material, the performance of the remanufactured cell, and the energy required for the complete process. The electrochemical performance of recycled material is comparable to that of as-manufactured cathode material, indicating no detrimental effect of purified recycled transition metal content. This research represents an important step toward scalable approaches to the recycling of EOL cathode material in LIBs.

Redox-active electrolyte for supercapacitor application.

This paper reports the electrochemical behaviour of supercapacitor carbon electrodes operating in different aqueous solutions modified by various redox-active species (hydroxybenzenes, bromine derivatives and iodide). Three dihydroxybenzenes with varying stereochemistry, i.e., -OH substitution, have been considered as electrolyte additives (0.38 mol L(-1)) in acidic, alkaline and neutral solutions. High capacitance values have been obtained, especially for the acidic and alkaline solutions containing 1,4-dihydroxybenzene (hydroquinone). Bromine derivatives of dihydroxybenzenes were also considered as the additive in alkaline solution for use as a supercapacitor electrolyte, and a significant increase in capacitance value was observed. The redox couple investigated next was an iodide/iodine system, where 2 mol L(-1) NaI aqueous electrolyte was utilized. In this case, the most promising faradaic contribution during capacitor operation was achieved. In particular, stable capacitance values from 300-400 F g(-1) have been confirmed by long-term galvanostatic cycling (over 100 000 cycles), cycling voltammetry and floating. The mechanism of pseudocapacitance phenomena was discussed and supported by electrochemical and physicochemical measurements, e.g., in situ Raman spectroscopy.