Simultaneous modal phase and group velocity matching in microstructured optical fibers for second harmonic generation with ultrashort pulses.

Optical fibers provide a favorable medium for nonlinear optical processes owing to the small mode field size and concurrently high optical intensity combined with the extended interaction lengths. Second harmonic generation (SHG) is one of those processes that has been demonstrated in silica glass optical fibers. Since silica is centrosymmetric, generating SHG in an optical fiber requires poling of the glass. In addition and when one wants to use ultrashort pulses for SHG, achieving both phase and group velocity matching is crucial. Although fibers that feature either modal phase velocity or group velocity matching for SHG have been reported, the possibility of simultaneous modal phase and group velocity matching was never reported before. In this paper we address this challenge, and for the first time to our knowledge, we show that it is feasible to do so with silica microstructured optical fibers featuring at least one ring of air holes in the cladding and a heavily Germanium doped core (above 25 mol.%) by exploiting the LP01(ω) and LP02(2ω) modes at 1.06 µm pump and 0.53 µm second harmonic wavelengths. This finding can greatly impact applications requiring waveguide based SHG generation with ultrashort pulses, including microscopy, material characterization and nonlinear imaging.

Highly birefringent microstructured optical fiber for distributed hydrostatic pressure sensing with sub-bar resolution.

We demonstrate distributed optical fiber-based pressure measurements with sub-bar pressure resolution and 1 m spatial resolution over a ∼100 m distance using a phase-sensitive optical time-domain reflectometry technique. To do so, we have designed a novel highly birefringent microstructured optical fiber that features a high pressure to temperature sensitivity ratio, a high birefringence and a mode field diameter that is comparable to that of conventional step-index single mode fibers. Our experiments with two fibers fabricated according to the design confirm the high polarimetric pressure sensitivities (-62.4 rad×MPa-1×m-1 and -40.1 rad×MPa-1×m-1) and simultaneously low polarimetric temperature sensitivities (0.09 rad×K-1×m-1 and 0.2 rad×K-1×m-1), at a wavelength of 1550 nm. The fiber features a sufficiently uniform birefringence over its entire length (2.17×10-4 ± 7.65×10-6) and low propagation loss (∼3 dB/km), which allows envisaging pressure measurements along distances up to several kilometers.

Impact of FBG feedback phase on laser dynamics.

Fiber Bragg gratings (FBGs) have been advantageously used to improve the chaotic properties of semiconductor lasers. Though these components are known to be highly sensitive to environmental conditions, feedback phase fluctuations are often neglected. In this work, we experimentally demonstrate that the small variations of the propagation time induced by a simple thermal tuning of the FBG are sufficient to induce significant changes of the laser behavior. We report periodic stability enhancements linked with phase variations and highlight that both phase variation and phase offsets play an important role. Last, we show a good qualitative agreement with simulations based on an expanded version of the Lang-Kobayashi model.

Long-distance distributed pressure sensing based on frequency-scanned phase-sensitive optical time-domain reflectometry.

In this paper, a long-distance distributed pressure sensing system based on a special fiber and using frequency-scanned phase-sensitive optical time-domain reflectometry is proposed. The fiber shows high pressure sensitivity (159 MHz/bar) and low loss (3 dB/km) owing to its simple structure made of two large air holes in the cladding. The pressure response of the two orthogonal polarization axes of the fiber is explored distinctively. Distributed pressure sensing over a long sensing range (720 m) and high spatial resolution (5 cm) is demonstrated, resulting in 14,400 resolved sensing points with uncertainty on pressure of 0.49 bar. Discrimination between the temperature/strain and pressure responses is demonstrated, taking advantage of the different pressure and temperature sensitivities of the two polarization axes. In addition, the temperature response of the fiber is studied and the simulation results show the possibility of scaling the temperature sensitivity by adjusting the size of the core. The sensing distance limit due to crosstalk between the polarization axes is also discussed.

Miniature freeform flow-line lightguide for sensing: from design to fabrication.

We present the development of a compact (about 1.3 × 2.0 × 20 mm3) freeform optical lightguide for sensing applications, from the conceptual design to the fabrication through injection molding. The design of the optic is based on the flow-line method from Nonimaging Optics, which allows the desired optical functionalities (45° half-acceptance and 40° beam steering) while meeting particularly tight mechanical and geometrical constraints. An extensive analysis of the effects of fabrication parameters on the performances demonstrates the importance of minimizing the fillet radius. This requisite inspired a special procedure for designing the mold, which is built as a "3D puzzle" assembly of separate pieces, each one dedicated to one specific side surface of the lightguide. This technique enables uniform optical quality on all the optic's surfaces and removes the need of a fillet radius in the mold. At present, the first lightguide prototypes have been fabricated; after the coating phase, they will be ready for the validation stage.

Monitoring of Torque Induced Strain in Composite Shafts with Embedded and Surface-Mounted Optical Fiber Bragg Gratings.

In this study, silica glass, optical fiber Bragg gratings (FBGs) are used for torque-induced strain monitoring in carbon fiber reinforced polymer (CFRP) hollow shafts toward the development of a methodology for structural load monitoring. Optical fibers with gratings are embedded during shaft manufacturing, by an industrial filament winding process, along different orientations with respect to its central axis and surface mounted after production. Experimental results are supported by numerical modeling of the shaft with appropriate boundary conditions and homogenized material properties. For an applied torque up to 800 Nm, the strain sensitivity of an embedded grating positioned along the reinforcing fibers' direction winded under 55° is in the order of 3.6 pm/Nm, while this value is more than 4× times higher than the other examined orientations. The study also shows that surface-mounted optical fiber Bragg gratings along the reinforcing carbon fibers' direction perform equally well in monitoring strains in composite shafts under torque.

Spectral Verification of the Mechanisms behind FBG-Based Ultrasonic Guided Wave Detection.

Ultrasonic guided wave (UGW) detection with fiber Bragg grating (FBG)-based sensors has received increasing attention in the last decades due to the ability to perform non-destructive inspection (NDI) of large plate-like surfaces with a network of lightweight and multiplexed sensors. For accurate UGW measurements, several studies concluded that the ratio between the wavelength of the UGW and the length of the FBG should be above 7. However, shorter FBGs suffer from a lower FBG reflectivity and less steep slopes in the reflection spectrum. In this work we experimentally verified the effect of a passing UGW on the Bragg peak of FBG sensors of different lengths. By performing edge-filtering interrogation throughout the FBG's reflection spectrum, we were able to reconstruct the FBG's spectral response to a UGW in function of time. Our experimental findings are partially in line with those in the literature considering the UGW wavelength to FBG length ratio and the corresponding Bragg peak changes. We experimentally show for the first time that for shorter FBG sensors, the strain modulation is translated mostly into Bragg peak shifting, while for longer FBG sensors, Bragg peak deformation takes over as main mechanism. Despite the different mechanism for the latter, the UGW can still be detected by edge-filtering on the steepest slope, and with a much higher sensitivity.

Bend-Direction and Rotation Plastic Optical Fiber Sensor.

A plastic filament of poly (methyl methacrylate) (PMMA) was fabricated by extrusion. The mode confinement was simulated using numerical software. The idea is to study how the light intensity changes inside the plastic optical fiber (POF) when a bending in multiple directions is applied. The results obtained from the simulation were compared to the experimental observations. The non-circular shape of the POF allows sensing a rotation applied as well. The angle of rotation was obtained processing two images of the end facet of the fiber (one with the fiber in a reference position and one with the rotated fiber), using an intensity-based automatic image registration. The accuracy in the rotation calculation was of 0.01°.

Effect of hydrogen gas on FBG-based optical fiber sensors for downhole pressure and temperature monitoring.

The influence of hydrogen gas on Fiber Bragg Grating (FBG)-based optical fiber sensors has been validated experimentally. More in particular, the focus was on FBGs written in the so-called Butterfly Micro Structured Fiber that targets simultaneous pressure and temperature monitoring with a minimum in cross-sensitivity to be used in, for example, downhole applications for the oil and gas market. The hydrogen-induced pressure and temperature errors from this type of sensor have been quantified as a function of the partial hydrogen pressure. The induced errors can be related to the diffusion of the hydrogen into the microstructure and to refractive index changes due to the presence of the hydrogen in the micro holes and penetration of it into the fiberglass. Furthermore, we have also shown that the hydrogen-induced errors scale with the partial hydrogen pressure.

FBGs written in specialty fiber for high pressure/high temperature measurement.

In this paper, we evaluate different thermal treatments in order to stabilize fiber Bragg gratings written by a femtosecond pulsed laser in specialty highly birefringent micro-structured optical fiber, targeting pressure monitoring at high pressure and high temperature environments. We have obtained a pressure sensitivity of 3.30 pm/bar up to 1400 bar and 290 °C. An effective thermal treatment has been experimentally implemented, yielding a nearly unchanged reflectivity at high temperature in combination with stable temperature and pressure readings: a standard deviation of 0.42 bar in the pressure reading was observed over 7 days at 280°C.

Fibre Bragg Gratings in Embedded Microstructured Optical Fibres Allow Distinguishing between Symmetric and Anti-Symmetric Lamb Waves in Carbon Fibre Reinforced Composites.

Conventional contact sensors used for Lamb wave-based ultrasonic inspection, such as piezo-electric transducers, measure omnidirectional strain and do not allow distinguishing between fundamental symmetric and anti-symmetric modes. In this paper, we show that the use of a single fibre Bragg grating created in a dedicated microstructured optical fibre allows one to directly make the distinction between these fundamental Lamb wave modes. This feature stems from the different sensitivities of the microstructured fibre to axial and transverse strain. We fabricated carbon fibre-reinforced polymer panels equipped with embedded microstructured optical fibre sensors and experimentally demonstrated the strain waves associated with the propagating Lamb waves in both the axial and transverse directions of the optical fibre.

Numerical modeling of femtosecond laser inscribed IR gratings in photonic crystal fibers.

During grating inscription in photonic crystal fibers (PCFs) the intensity of the inscribing laser beam is non-uniformly distributed over the core region due to the interaction with the air holes in the fiber's microstructure. In this paper we model and study the non-uniformity of the index modification and its influence on the grating reflection spectra, taking into account the non-linear nature of the index change. For femtosecond laser inscription pulses at 800 nm, we show that the intensity redistribution in the PCF core region can result in Type II index changes even if the peak intensity of the incident beam is well below the corresponding threshold. Our coupled mode analysis reveals that the non-uniform nature of the index change can seriously affect the reflectivity of the grating due to a limited overlap of the guided mode with the transverse index modulation profile for almost all angular orientations of the PCFs with respect to the inscription beam. We also evaluate the influence of PCF tapering and we found that for the considered PCF a significant increase in the induced index change and reflectivity is observed only for taper diameters below 40 µm.

Algorithms for determining the radial profile of the photoelastic coefficient in glass and polymer optical fibers.

We discuss two algorithms to determine the value and the radial profile of the photoelastic coefficient C in glass and polymer optical fibers. We conclude that C is constant over the fiber cross-sections, with exception of silica glass fibers containing a fluorine-doped depressed cladding. In the undoped and Ge-doped parts of these silica glass fibers we find a consistent value for C that is slightly larger than in bulk silica. In the fluorine-doped trenches of the absolute value of C decreases with about 27%. In polymethyl methacrylate optical fibers, the value of C significantly varies from fiber to fiber.

A micro-computed tomography technique to study the quality of fibre optics embedded in composite materials.

Quality of embedment of optical fibre sensors in carbon fibre-reinforced polymers plays an important role in the resultant properties of the composite, as well as for the correct monitoring of the structure. Therefore, availability of a tool able to check the optical fibre sensor-composite interaction becomes essential. High-resolution 3D X-ray Micro-Computed Tomography, or Micro-CT, is a relatively new non-destructive inspection technique which enables investigations of the internal structure of a sample without actually compromising its integrity. In this work the feasibility of inspecting the position, the orientation and, more generally, the quality of the embedment of an optical fibre sensor in a carbon fibre reinforced laminate at unit cell level have been proven.

Shear stress sensing with Bragg grating-based sensors in microstructured optical fibers.

We demonstrate shear stress sensing with a Bragg grating-based microstructured optical fiber sensor embedded in a single lap adhesive joint. We achieved an unprecedented shear stress sensitivity of 59.8 pm/MPa when the joint is loaded in tension. This corresponds to a shear strain sensitivity of 0.01 pm/µÎµ. We verified these results with 2D and 3D finite element modeling. A comparative FEM study with conventional highly birefringent side-hole and bow-tie fibers shows that our dedicated fiber design yields a fourfold sensitivity improvement.

Influence of measurement noise on the determination of the radial profile of the photoelastic coefficient in step-index optical fibers.

We discuss a measurement method that aims to determine the radial distribution of the photoelastic constant C in an optical fiber. This method uses the measurement of the retardance profile of a transversely illuminated fiber as a function of applied tensile load and requires the computation of the inverse Abel transform of this retardance profile. We focus on the influence of the measurement error on the obtained values for C. The results suggest that C may not be constant across the fiber and that the mean absolute value of C is slightly larger for glass fibers than for bulk fused silica. This can, for example, influence the accuracy with which one is able to predict the response of optical fiber sensors used for measuring mechanical loads.

Temperature-insensitive polarimetric vibration sensor based on HiBi microstructured optical fiber.

A new type of highly birefringent microstructured optical fiber has been tested for vibration measurements using a polarimetric technique. This technique takes advantage of the stress-induced phase shift between the two orthogonally polarized fiber eigenmodes. Comparison of three different fiber types shows that standard single-mode fibers do not provide stable measurements and that conventional polarization-maintaining fibers lead to a significant cross-sensitivity to temperature. However, for highly birefringent microstructured fibers specifically designed to provide a temperature-independent birefringence, our experiments show repeatable vibration measurements over a frequency range extending from 50 Hz to 1 kHz that are unaffected by temperature variations (up to 120 °C).

Geometrical study of a hexagonal lattice photonic crystal fiber for efficient femtosecond laser grating inscription.

We have studied transverse propagation of femtosecond pulse duration laser light through the microstructure of hexagonal lattice photonic crystal fibers. Our results provide insight in the role of the microstructure on the amount of optical power that reaches the core of the PCF, which is of particular importance for grating inscription applications. We developed a dedicated approach based on commercial FDTD software and defined a figure of merit, the transverse coupling efficiency, to evaluate the coupling process. We analyzed the propagation of femtosecond laser pulses to the core of a wide range of PCFs and studied the influence of the PCF orientation angle, the air hole pitch and air hole radius on the energy reaching the core. We have found that the transverse coupling efficiency can benefit from a dedicated design of the microstructured cladding and an accurate fiber orientation. We designed a dedicated PCF microstructure that enhances transverse coupling to the core at a wavelength of 800 nm.

Microstructured optical fiber sensors embedded in a laminate composite for smart material applications.

Fiber Bragg gratings written in highly birefringent microstructured optical fiber with a dedicated design are embedded in a composite fiber-reinforced polymer. The Bragg peak wavelength shifts are measured under controlled axial and transversal strain and during thermal cycling of the composite sample. We obtain a sensitivity to transversal strain that exceeds values reported earlier in literature by one order of magnitude. Our results evidence the relevance of using microstructured optical fibers for structural integrity monitoring of composite material structures.

Challenges in the Fabrication of Biodegradable and Implantable Optical Fibers for Biomedical Applications.

The limited penetration depth of visible light in biological tissues has encouraged researchers to develop novel implantable light-guiding devices. Optical fibers and waveguides that are made from biocompatible and biodegradable materials offer a straightforward but effective approach to overcome this issue. In the last decade, various optically transparent biomaterials, as well as different fabrication techniques, have been investigated for this purpose, and in view of obtaining fully fledged optical fibers. This article reviews the state-of-the-art in the development of biocompatible and biodegradable optical fibers. Whilst several reviews that focus on the chemical properties of the biomaterials from which these optical waveguides can be made have been published, a systematic review about the actual optical fibers made from these materials and the different fabrication processes is not available yet. This prompted us to investigate the essential properties of these biomaterials, in view of fabricating optical fibers, and in particular to look into the issues related to fabrication techniques, and also to discuss the challenges in the use and operation of these optical fibers. We close our review with a summary and an outline of the applications that may benefit from these novel optical waveguides.