Spreading Solution Additives Governs the Quality of Polystyrene Particle-Based Two-Dimensional Opals.

Two-dimensional polystyrene sphere opals are important materials for nanotechnology applications and fundamental nanoscience research. They are a facile and inexpensive nanofabrication tool, but the quality factor of these opals has drastic differences between reports. Additives like ethanol, ions, and organic molecules in the aqueous particle spreading solution are known to affect the quality factor and growth efficiency of the produced opals. However, a systematic study on the effect and optimization of some of the most effective additives has not been reported until now. Here, we investigate the influence of additives on the growth efficiency and quality factor of such monolayers formed at the air-water interface without the use of a Langmuir-Blodgett trough. The additives induced large variations in the monolayer quality factor and growth efficiency, and we found that the ideal additive content of the spreading agents is 30 wt % < cethanol < 70 wt %, 0 < cH2SO4 < 30.5 mM, and 0 < csty < 255.0 mM. This study provides a guideline for the rational composition and additive content of the spreading solution to obtain high-quality two-dimensional opals for further applications in nanofabrication and photonics and will enable researchers and application engineers to produce standardized nanofabrication materials.

Upcycling of Acid-Leaching Solutions from Li-Ion Battery Waste Treatment through the Facile Synthesis of Magnetorheological Fluid.

The rapidly growing production and usage of lithium-ion batteries (LIBs) dramatically raises the number of harmful wastes. Consequently, the LIBs waste management processes, taking into account reliability, efficiency, and sustainability criteria, became a hot issue in the context of environmental protection as well as the scarcity of metal resources. In this paper, we propose for the first time a functional material-a magnetorheological fluid (MRF) from the LIBs-based liquid waste containing heavy metal ions. At first, the spent battery waste powder was treated with acid-leaching, where the post-treatment acid-leaching solution (ALS) contained heavy metal ions including cobalt. Then, ALS was used during wet co-precipitation to obtain cobalt-doped superparamagnetic iron oxide nanoparticles (SPIONs) and as an effect, the harmful liquid waste was purified from cobalt. The obtained nanoparticles were characterized with SEM, TEM, XPS, and magnetometry. Subsequently, superparamagnetic nanoparticles sized 15 nm average in diameter and magnetization saturation of about 91 emu g-1 doped with Co were used to prepare the MRF that increases the viscosity by about 300% in the presence of the 100 mT magnetic fields. We propose a facile and cost-effective way to utilize harmful ALS waste and use them in the preparation of superparamagnetic particles to be used in the magnetorheological fluid. This work describes for the first time the second life of the battery waste in the MRF and a facile way to remove the harmful ingredients from the solutions obtained after the acid leaching of LIBs as an effective end-of-life option for hydrometallurgical waste utilization.

Lithography-free synthesis of periodic, vertically-aligned, multi-walled carbon nanotube arrays.

Until now, the growth of periodic vertically aligned multi-walled carbon nanotube (VA-MWCNT) arrays was dependent on at least one lithography step during fabrication. Here, we demonstrate a lithography-free fabrication method to grow hexagonal arrays of self-standing VA-MWCNTs with tunable pitch and MWCNT size. The MWCNTs are synthesized by plasma enhanced chemical vapor deposition (PECVD) from Ni catalyst particles. Template guided dewetting of a thin Ni film on a hexagonally close-packed silica particle monolayer provides periodically distributed Ni catalyst particles as seeds for the growth of the periodic MWCNT arrays. The diameter of the silica particles directly controls the pitch of the periodic VA-MWCNT arrays from 600 nm to as small as 160 nm. The diameter and length of the individual MWCNTs can also be readily adjusted and are a function of the Ni particle size and PECVD time. This unique method of lithography-free growth of periodic VA-MWCNT arrays can be utilized for the fabrication of large-scale biomimetic materials.

Extraordinary optical transmission in nano-bridged plasmonic arrays mimicking a stable weakly-connected percolation threshold.

Ultrasensitive sensors of various physical properties can be based on percolation systems, e.g., insulating media filled with nearly touching conducting particles. Such a system at its percolation threshold featuring the critical particle concentration, changes drastically its response (electrical conduction, light transmission, etc.) when subjected to an external stimulus. Due to the critical nature of this threshold, a given state at the threshold is typically very unstable. However, stability can be restored without significantly sacrificing the structure sensitivity by forming weak connections between the conducting particles. In this work, we employed nano-bridged nanosphere lithography to produce such a weakly connected percolation system. It consists of two coupled quasi-Babinet complementary arrays, one with weakly connected, and the other with disconnected metallic islands. We demonstrate via experiment and simulation that the physics of this plasmonic system is non-trivial, and leads to the extraordinary optical transmission at narrowly defined peaks sensitive to system parameters, with surface plasmons mediating this process. Thus, our system is a potential candidate for percolation effect based sensor applications. Promising detection schemes could be based on these effects.

Nano-bridged nanosphere lithography.

We develop nano-bridged nanosphere lithography (NB-NSL), a modification to the widely used conventional nanosphere lithography (NSL). Nano-bridges between polystyrene (PS) spheres of a pristine NSL template are controllably formed in a two-step process: (i) spin-coating of a dilute styrene solution on top of the template, followed by (ii) oxygen plasma etching of the template. We show that the nanobridge dimensions can be precisely tuned by controlling the pre-processing conditions and the plasma etching time. The resulting lithography templates feature control over the shape and size of the apertures, which determine the morphology of the final nano-island arrays after material deposition and template removal. The unique advantage of NB-NSL is that PS particle templates based on a single PS particle diameter can be utilized for the fabrication of a variation of nano-island shapes and sizes, whereas conventional NSL yields only bowtie-shaped nano-islands, with their size being predetermined by the PS particle diameter of the template.

Plasmon resonances in coupled Babinet complementary arrays in the mid-infrared range.

A plasmonic structure with transmission highly tunable in the mid-infrared spectral range is developed. This structure consists of a hexagonal array of metallic discs located on top of silicon pillars protruding through holes in a metallic Babinet complementary film. We reveal with FDTD simulations that changing the hole diameter tunes the main plasmonic resonance frequency of this structure throughout the infrared range. Due to the underlying Babinet physics of these coupled arrays, the spectral width of these plasmonic resonances is strongly reduced, and the higher harmonics are suppressed. Furthermore, we demonstrate that this structure can be easily produced by a combination of the nanosphere lithography and the metal-assisted chemical etching technique.

Role of interactions in the magneto-plasmonic response at the geometrical threshold of surface continuity: publisher's note.

This publisher's note amends the author listing of [Opt. Express26, 32792 (2017)].

Advancing semiconductor-electrocatalyst systems: application of surface transformation films and nanosphere lithography.

Photoelectrochemical (PEC) cells offer the possibility of carbon-neutral solar fuel production through artificial photosynthesis. The pursued design involves technologically advanced III-V semiconductor absorbers coupled via an interfacial film to an electrocatalyst layer. These systems have been prepared by in situ surface transformations in electrochemical environments. High activity nanostructured electrocatalysts are required for an efficiently operating cell, optimized in their optical and electrical properties. We demonstrate that shadow nanosphere lithography (SNL) is an auspicious tool to systematically create three-dimensional electrocatalyst nanostructures on the semiconductor photoelectrode through controlling their morphology and optical properties. First results are demonstrated by means of the photoelectrochemical production of hydrogen on p-type InP photocathodes where hitherto applied photoelectrodeposition and SNL-deposited Rh electrocatalysts are compared based on their J-V and spectroscopic behavior. We show that smaller polystyrene particle masks achieve higher defect nanostructures of rhodium on the photoelectrode which leads to a higher catalytic activity and larger short circuit currents. Structural analyses including HRSEM and the analysis of the photoelectrode surface composition by using photoelectron spectroscopy support and complement the photoelectrochemical observations. The optical performance is further compared to theoretical models of the nanostructured photoelectrodes on light scattering and propagation.

Long-term release of antibiotics by carbon nanotube-coated titanium alloy surfaces diminish biofilm formation by Staphylococcus epidermidis.

Bacterial biofilms cause a considerable amount of prosthetic joint infections every year, resulting in morbidity and expensive revision surgery. To address this problem, surface modifications of implant materials such as carbon nanotube (CNT) coatings have been investigated in the past years. CNTs are biologically compatible and can be utilized as drug delivery systems. In this study, multi-walled carbon nanotube (MWCNT) coated TiAl6V4 titanium alloy discs were fabricated and impregnated with Rifampicin, and tested for their ability to prevent biofilm formation over a period of ten days. Agar plate-based assays were employed to assess the antimicrobial activity of these surfaces against Staphylococcus epidermidis. It was shown that vertically aligned MWCNTs were more stable against attrition on rough surfaces than on polished TiAl6V4 surfaces. Discs with coated surfaces caused a significant inhibition of biofilm formation for up to five days. Therefore, MWCNT-modified surfaces may be effective against pathogenic biofilm formation on endoprostheses.

Au@MnO2 core-shell nanomesh electrodes for transparent flexible supercapacitors.

A novel Au@MnO2 supercapacitor is presented. The sophisticated core-shell architecture combining an Au nanomesh core with a MnO2 shell on a flexible polymeric substrate is demonstrated as an electrode for high performance transparent flexible supercapacitors (TFSCs). Due to their unique structure, high areal/gravimetric capacitance and rate capability for TFSCs are achieved.

Understanding anisotropic plasma etching of two-dimensional polystyrene opals for advanced materials fabrication.

Anisotropic deformation of polystyrene particles in an oxygenated (O2/Ar) plasma is observed for radio frequency (rf) plasma and inductively coupled plasma (ICP). A facile model based on a ratio of completely isotropic and completely anisotropic etching is presented to describe the anisotropy of the etching process and is implemented to determine the height of the spheroid-shaped polystyrene particles. In our systems, we find the plasma etching to be 54% isotropic in the rf plasma and 79% isotropic in the ICP. With this model, the maximum material deposition thickness for nanofabrication with plasma-etched nanosphere lithography or colloid lithography can be predicted. Moreover, the etching of polystyrene particles in an oxygenated plasma is investigated versus the etching time, gas flow, gas composition, temperature, substrate material, and particle size. The results of this study allow precise shape tuning during the fabrication of nanostructured surfaces with size-dependent properties for bionic, medical, and photonic applications.

How scanning probe microscopy can be supported by artificial intelligence and quantum computing?

The impact of Artificial Intelligence (AI) is rapidly expanding, revolutionizing both science and society. It is applied to practically all areas of life, science, and technology, including materials science, which continuously requires novel tools for effective materials characterization. One of the widely used techniques is scanning probe microscopy (SPM). SPM has fundamentally changed materials engineering, biology, and chemistry by providing tools for atomic-precision surface mapping. Despite its many advantages, it also has some drawbacks, such as long scanning times or the possibility of damaging soft-surface materials. In this paper, we focus on the potential for supporting SPM-based measurements, with an emphasis on the application of AI-based algorithms, especially Machine Learning-based algorithms, as well as quantum computing (QC). It has been found that AI can be helpful in automating experimental processes in routine operations, algorithmically searching for optimal sample regions, and elucidating structure-property relationships. Thus, it contributes to increasing the efficiency and accuracy of optical nanoscopy scanning probes. Moreover, the combination of AI-based algorithms and QC may have enormous potential to enhance the practical application of SPM. The limitations of the AI-QC-based approach were also discussed. Finally, we outline a research path for improving AI-QC-powered SPM. RESEARCH HIGHLIGHTS: Artificial intelligence and quantum computing as support for scanning probe microscopy. The analysis indicates a research gap in the field of scanning probe microscopy. The research aims to shed light into ai-qc-powered scanning probe microscopy.

A Stable Perovskite Sensitized Photonic Crystal P-N Junction with Enhanced Photoelectrochemical Hydrogen Production.

The slow photon effect in inverse opal photonic crystals represents a promising approach to manipulate the interactions between light and matter through the design of material structures. This study introduces a novel ordered inverse opal photonic crystal (IOPC) sensitized with perovskite quantum dots (PQDs), demonstrating its efficacy for efficient visible-light-driven H2 generation via water splitting. The rational structural design contributes to enhanced light harvesting. The sensitization of the IOPC with PQDs improves optical response performance and enhances photocatalytic H2 generation under visible light irradiation compared to the IOPC alone. The designed photoanode exhibits a photocurrent density of 3.42 mA cm-2 at 1.23 V vs RHE. This work advances the rational design of visible light-responsive photocatalytic heterostructure materials based on wide band gap metal oxides for photoelectrochemical applications.

Transparent nanowire network electrode for textured semiconductors.

This work presents an inexpensive and easily manufacturable, highly conductive and transparent nanowire network electrode for textured semiconductors. It is based on lines of silver nanoparticles transformed into a nanowire network by microwave or furnace sintering. The nanonetwork electrode on crystalline silicon is demonstrated experimentally, with the nanoparticles self-assembling in the valleys between the pyramids of the textured surface. Optical experiments show that this conductive nanowire network electrode can be essentially 'invisible' when covered with the conventional anti-reflection coating (ARC), and thus could be employed in photovoltaic applications.

Oxidative Stress in Long-Term Exposure to Multi-Walled Carbon Nanotubes in Male Rats.

Multi-walled carbon nanotubes (MWCNTs) serve as nanoparticles due to their size, and for that reason, when in contact with the biological system, they can have toxic effects. One of the main mechanisms responsible for nanotoxicity is oxidative stress resulting from the production of intracellular reactive oxygen species (ROS). Therefore, oxidative stress biomarkers are important tools for assessing MWCNTs toxicity. The aim of this study was to evaluate the oxidative stress of multi-walled carbon nanotubes in male rats. Our animal model studies of MWCNTs (diameter ~15-30 nm, length ~15-20 µm) include measurement of oxidative stress parameters in the body fluid and tissues of animals after long-term exposure. Rattus Norvegicus/Wistar male rats were administrated a single injection to the knee joint at three concentrations: 0.03 mg/mL, 0.25 mg/mL, and 0.5 mg/mL. The rats were euthanized 12 and 18 months post-exposure by drawing blood from the heart, and their liver and kidney tissues were removed. To evaluate toxicity, the enzymatic activity of total protein (TP), reduced glutathione (GSH), glutathione S-transferase (GST), thiobarbituric acid reactive substances (TBARS), Trolox equivalent antioxidant capacity (TEAC), nitric oxide (NO), and catalase (CAT) was measured and histopathological examination was conducted. Results in rat livers showed that TEAC level was decreased in rats receiving nanotubes at higher concentrations. Results in kidneys report that the level of NO showed higher concentration after long exposure, and results in animal serums showed lower levels of GSH in rats exposed to nanotubes at higher concentrations. The 18-month exposure also resulted in a statistically significant increase in GST activity in the group of rats exposed to nanotubes at higher concentrations compared to animals receiving MWCNTs at lower concentrations and compared to the control group. Therefore, an analysis of oxidative stress parameters can be a key indicator of the toxic potential of multi-walled carbon nanotubes.

Highly Flexible and Acid-Alkali Resistant TiN Nanomesh Transparent Electrodes for Next-Generation Optoelectronic Devices.

Transparent electrodes are vital for optoelectronic devices, but their development has been constrained by the limitations of existing materials such as indium tin oxide (ITO) and newer alternatives. All face issues of robustness, flexibility, conductivity, and stability in harsh environments. Addressing this challenge, we developed a flexible, low-cost titanium nitride (TiN) nanomesh transparent electrode showcasing exceptional acid-alkali resistance. The TiN nanomesh electrode, created by depositing a TiN coating on a naturally cracked gel film substrate via a sputtering method, maintains a stable electrical performance through thousands of bending cycles. It exhibits outstanding chemical stability, resisting strong acid and alkali corrosion, which is a key hurdle for current electrodes when in contact with acidic/alkaline materials and solvents during device fabrication. This, coupled with superior light transmission and conductivity (88% at 550 nm with a sheet resistance of ∼200 Ω/sq), challenges the reliance on conventional materials. Our TiN nanomesh electrode, successfully applied in electric heaters and electrically controlled thermochromic devices, offers broad potential beyond harsh environment applications. It enables alternative possibilities for the design and fabrication of future optoelectronics for advancements in this pivotal field.

Releasing the Bubbles: Nanotopographical Electrocatalyst Design for Efficient Photoelectrochemical Hydrogen Production in Microgravity Environment.

Photoelectrochemical devices integrate the processes of light absorption, charge separation, and catalysis for chemical synthesis. The monolithic design is interesting for space applications, where weight and volume constraints predominate. Hindered gas bubble desorption and the lack of macroconvection processes in reduced gravitation, however, limit its application in space. Physico-chemical modifications of the electrode surface are required to induce gas bubble desorption and ensure continuous device operation. A detailed investigation of the electrocatalyst nanostructure design for light-assisted hydrogen production in microgravity environment is described. p-InP coated with a rhodium (Rh) electrocatalyst layer fabricated by shadow nanosphere lithography is used as a model device. Rh is deposited via physical vapor deposition (PVD) or photoelectrodeposition through a mask of polystyrene (PS) particles. It is observed that the PS sphere size and electrocatalyst deposition technique alter the electrode surface wettability significantly, controlling hydrogen gas bubble detachment and photocurrent-voltage characteristics. The highest, most stable current density of 37.8 mA cm-2 is achieved by depositing Rh via PVD through 784 nm sized PS particles. The increased hydrophilicity of the photoelectrode results in small gas bubble contact angles and weak frictional forces at the solid-gas interface which cause enhanced gas bubble detachment and enhanced device efficiency.

3D hierarchically porous magnetic molybdenum trioxide@gold nanospheres as a nanogap-enhanced Raman scattering biosensor for SARS-CoV-2.

The global pandemic of COVID-19 is an example of how quickly a disease-causing virus can take root and threaten our civilization. Nowadays, ultrasensitive and rapid detection of contagious pathogens is in high demand. Here, we present a novel hierarchically porous 3-dimensional magnetic molybdenum trioxide-polydopamine-gold functionalized nanosphere (3D mag-MoO3-PDA@Au NS) composed of plasmonic, semiconductor, and magnetic nanoparticles as a multifunctional nanosculptured hybrid. Based on the synthesized 3D mag-MoO3-PDA@Au NS, a universal "plug and play" biosensor for pathogens is proposed. Specifically, a magnetically-induced nanogap-enhanced Raman scattering (MINERS) detection platform was developed using the 3D nanostructure. Through a magnetic actuation process, the MINERS system overcomes Raman signal stability and reproducibility challenges for the ultrasensitive detection of SARS-CoV-2 spike protein over a wide dynamic range up to a detection limit of 10-15 g mL-1. The proposed MINERS platform will facilitate the broader use of Raman spectroscopy as a powerful analytical detection tool in diverse fields.

Transmission of light through magnetic nanocavities.

The transmission of light through a metallic film stack on a transparent substrate, perforated with a periodic array of cylindrical holes/nanocavities, is studied. The structure is fabricated by using self-assembled nanosphere lithography. Since one layer in the film stack is made of a ferromagnetic metal (iron), exposure of the structure to a solution containing iron oxide nanoparticles causes nanoparticle accumulation inside the nanocavities. This changes the dielectric constant inside the nanocavities and thus affects the light transmission. Simulations are in good agreement with experiment, and show large sensitivity of the response to the amount of iron oxide nanoparticles deposited. This could be used in various sensor applications.

Surface plasmons and magneto-optic activity in hexagonal Ni anti-dot arrays.

The influence of surface plasmons on the magneto-optic activity in a two-dimensional hexagonal array is addressed. The experiments were performed using hexagonal array of circular holes in a ferromagnetic Ni film. Well pronounced troughs are observed in the optical reflectivity, resulting from the presence of surface plasmons. The surface plasmons are found to strongly enhance the magneto-optic response (Kerr rotation), as compared to a continuous film of the same composition. The influence of the hexagonal symmetry of the pattern on the coupling between the plasmonic excitations is demonstrated, using optical diffraction measurements and theoretical calculations of the magneto-optic and of the angular dependence of the optical activity.